You mention that you ran the "KAT500 Configuration Software"
but you didn't say that you tried to reload the firmware.
Have you tried to RELOAD the firmware? If you didn't reload
the firmware, then I would suggest that you give that a try.
73
There are numerous AGC adjustments available in the CONFIG
menu. You can probably find something to suit you there.
73, Ken K3IU
On 7/19/2019 4:14 AM, Roger wrote:
Hi,
when operating the K3S in CW mode I found there is no difference
I built #2888 in Oct 2002.
Ken K3IU
~
On 4/14/2019 11:48 AM, Bud wrote:
I am interested in learning the year that the K2 was introduced into the
Amateur Radio market.
And, what is the approximate year K2 s/n 2514 was shipped?
Thanks to the Elecraft historian
the gain settings on the filter being used. 73, Ken K3IU
~
On 2/22/2019 1:28 PM, Nate Bargmann wrote:
No ideas at all regarding this or did I fail to explain the issue I am
seeing well enough?
73, Nate, N0NB
Good Morning, Barry:
Sounds like a problem that raised its head quite a while back with
corrosion of the 12V pins on the KPA3 connector. I am not near my rig
and info at the moment so I can't confirm that.
73 and Happy Holidays,
Ken K3IU
On 12/17/2017 1:36 AM, Barry Simpson wrote:
I have
the phones were plugged into
the Rear Panel, but did mute when thephones were plugged
into the Front Panel.
73,
Ken K3IU
K3s #10691
~~
On 3/6/2017 10:30 AM, M. George wrote:
Same problem here Bill. I never noticed this on my K3. I sent an email to
Elecraft support.
I am using 5.57 here and tapping either the shift or width
knobs causes the function to cycle between Lo/HI and
Shift/Width with the Green LEDs to switch as well.
73, Ken K3IU
~~
On 2/26/2017 10:13 AM, Ted Bryant wrote:
In playing with Bob N6TV's
I sent an email query to Gary Surrency this morning, but of course have
not yet heard back from him yet.
73, Ken K3IU
~
On 12/11/2016 12:12 PM, Richard Thorne wrote:
...
I'd like to know what the mod is as well.
Rich - N5ZC
73,
Ken Wagner K3IU
Portsmouth, RI
kenk...@cox.net
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
This is as low as it is going to get!
This is an oldie but goodie (s/n 2xx) which has all official
mods and enhancements available to this serial number and is
fully functional to the latest specs. I am the original
owner and the radio has always been in a non-smoking
environment. I have a
This is an oldie but goodie (s/n 2xx) which has all official
mods and enhancements available to this serial number and is
fully functional to the latest specs. I am the original
owner and the radio has always been in a non-smoking
environment. I have a new K3S and this K3 is now excess to
my
This is an oldie but goodie (s/n 2xx) which has all official
mods and enhancements available to this serial number and is
fully functional to the latest specs. I am the original
owner and the radio has always been in a non-smoking
environment. I have a new K3S and this K3 is now excess to
my
It is in great shape and fully functional to original specs
and has been well maintained over the years with all known
official mods and updates applicable to this serial number.
Additionally, it has the new and improved synthesizer
board(KSYN3A) and Interface module (KXV3B) installed (Same
It is in great shape and fully functional to original specs
and has been well maintained over the years with all known
official mods and updates applicable to this serial number.
Additionally, it has the new and improved synthesizer
board(KSYN3A) and Interface module (KXV3B) installed (Same
You might check the Block Diagram om the K3 Manual for the
answer to your question.
73, Ken K3IU
~~~
On 3/21/2016 5:52 AM, Gary wrote:
Anyone confirm the k3 has audio IF of 1.5khz?
Gary
I recently purchased a new K3s and no longer have use for my
old K3 friend #202. Of course, it is not pristine having
been opened up and put back together many times over the
last 9 year, but it is in great shape and fully functional
to original specs and has been well maintained over the
I recently purchased a new K3s and no longer have use for my
old K3 friend #202. Of course, it is not pristine having
been opened up and put back together many times over the
last 9 year, but it is fully functional to original specs
and has been well maintained over the years with all known
bout $3200 plus s/h.
Asking $2295 shipped UPS ground to CONUS. Will accept
PayPal, USPS Money Order or bank draft.
Please reply off-reflector to
73, Ken K3IU
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elec
Hi Bob:
You can just put the K3 in SEMI breakin mode (Press hold
QSK button on Band UP) and set the delay to whatever you
want by adjusting the DELAY (press hold SPEED MIC and turn
knob to adjust). I believe that should produce the result
you are seeking.
73, Ken K3IU
I have the same thing here, Bruce. Something in firmware was
changed a while ago and when I reported it to Wayne, he said
that it is within specs.
73, Ken K3IU
~~~
On 1/9/2016 11:09 AM, Bruce Meier wrote:
Today I noticed that the output power
Same here, Vic. Pretty sure it has always been that way on 6
meters.
73, Ken K3IU
~~
On 12/20/2015 8:51 AM, Vic Rosenthal 4X6GP/K2VCO wrote:
This is strange. Firmware 5.33. On 6 meters when the PWR
control is turned all the way up, the VFO B
G'morning, Frank:
I just tried to duplicate what you are experiencing and was
unsuccessful. No interruptions. K3 #202 with latest firmware.
73, Ken K3IU
~~~
On 11/22/2015 8:54 PM, n...@comcast.net wrote:
I discovered a problem with my K3, s/n 83xx.
With nothing
that don't produce it
because I am not hearing any interruption at any interval.
Thanks for the info...
73, Ken K3IU
On 11/23/2015 9:34 AM, Jim - N4ST wrote:
Ken,
This is firmware problem acknowledged by Elecraft, and previously discussed
SOLD
On 8/1/2015 5:00 PM, Ken K3IU wrote:
Looks like I may have had too high expectations regarding
the asking price.
Price now reduced to $75 delivered via USPS .
73,
Ken K3IU
Portsmouth RI
Kenk3iu at cox.net
~~~
On 7/30/2015 5:26 AM, Ken K3IU
Looks like I may have had too high expectations regarding
the asking price.
Price now reduced to $75 delivered via USPS .
73,
Ken K3IU
Portsmouth RI
Kenk3iu at cox.net
~~~
On 7/30/2015 5:26 AM, Ken K3IU wrote:
I have purchased the KXV3B and now have
I have purchased the KXV3B and now have a PR6 external
preamp excess to my needs. $100 USPS Priority Mail delivered
in US. Please respond direct.
73,
Ken Wagner K3IU
Portsmouth, RI
kenk3iu @ cox.net
__
Elecraft mailing list
Home:
in the instructions.
I reconnected my beam and spot checked a few data points and
the birdies are still present and the same relative
strengths. The only one that might cause me some distress is
the one at abt 50.115, and I can remove that with the firmware.
73, Ken K3iU
Oops... sorry. I didn't mean for this to Reply to: Dave,
N1IX's email. Dag Nabbit!
73, Ken K3IU
~~~
Forwarded Message
Subject:Re: [Elecraft] WTB K3/10 or K3/100
Date: Wed, 24 Jun 2015 08:23:34 -0400
From: Ken K3IU kenk...@cox.net
G'morning, Scott:
I have been using a SS30 for several years (before Elecraft
began selling them) and have had no noise issues with it.
73, Ken K3IU
~~~
On 6/16/2015 1:22 AM, NE9U - Jasper wrote:
I was about to order a switching supply for portable
Mack:
I would suggest that before you contact Support you verify
that all of the TMP interconnect cables are snugly and
completely in place.
73, Ken K3IU
On 3/20/2015 9:30 AM, W4CCS wrote:
Mack:
I have not seen this problem.. Yes, I would contact tech support
Please leave it alone. The TX marker point to B and the
SPLIT with a border around it is enough.
73, Ken K3IU
~~
On 2/17/2015 7:38 PM, Wayne Burdick wrote:
Or, we could replace the *entire* VFO A display with the word SPLIT during
key-down
I believe that you should ne able to install both boards
without removing the KRX3
73, Ken K3IU
On 2/14/2015 10:03 AM, Dauer, Edward wrote:
First question that came to my mind when I saw the announcement was
whether the KRX3 had to be removed and reinstalled
Do you have K3CONFIGPWR SET set to Per Band?
73, Ken K3IU
~~~
On 5/13/2014 11:28 AM, Phil Theis wrote:
Greetings,
It was my understanding that power settings on the K3
would track separately when the KPA500 was off.
On my K3 if I set a power level with the 500
If memory serves me, you need to have the K3 in the range
before the CONFIG:WMTR will indicate that range, e.g., if
you have it set for 5 watts, it will show LP; if you have
set 12 watts, it will say HP.
73, Ken K3IU
~~
On 4/7/2014 9:30 AM, Ed G wrote:
Folks
202). In
all other respects, the 6425 performed just as I had
expected it would with no other issues.
Just wondering if anyone else has recently experienced this
audio pop and if so what did you do about it???
Thanks...
73, Ken K3IU
Original Message
Subject:Re: [Elecraft] K3 4.81 beta anomally
Date: Sat, 08 Feb 2014 05:58:23 -0500
From: Ken K3IU kenk...@cox.net
To: John_N1JM johnn...@gmail.com
I notice similar action once after the K3 had been on
overnight. Rebooting the K3 solved
Tap the Display Button.
73, Ken K3IU
On 11/17/2013 11:33 AM, Glenn Haffly wrote:
My K3 has a problem using the split function. When holding the split button
the split function shows the B VFO is controlling transmit. When turning
the B VFO knob all I get is time
In extended Rx... ambient temp 55-60F
FP=32C
PA=24C
73, Ken K3IU
~~~
On 11/13/2013 10:46 AM, Sam Morgan wrote:
What temp readings are others seeing for front panel and PA?
FP = 41C
PA = 36C
__
Elecraft
Jim:
Did you press the Tune button on the KAT500 before
pressing the TUNE button on the K3?
73, Ken K3IU
~~~
On 11/12/2013 2:40 PM, Jim Bennett wrote:
Folks, sorry if this has been discussed on the reflector before, but I've
looked through the archives
I am running it on Win7/64 and it works fine.
73,
Ken K3iU
On 11/8/2013 1:17 AM, Tom Field wrote:
Just out of curiosity, has anyone been able to run Spectrogram on Windows 7
or Windows 8. I haven't had any luck, and would like to reset my filters.
Tom F
to disconnect the KPA3, but other
postings suggest that the parasitic draw would significantly
drop if I did.
73, Ken K3IU
K3 #202
~~
On 10/16/2013 5:05 PM, Ken K3IU wrote:
Same here but only about 31ma on a Triplett 2202 DMM on K3
s/n 202.
73, Ken K3IU
Same here but only about 31ma on a Triplett 2202 DMM on K3
s/n 202.
73, Ken K3IU
~~~
On 10/16/2013 5:01 PM, Ron D'Eau Claire wrote:
I disconnected everything from my K3 except the power cable and the drain
when off remains at 38mA.
I don't have the time right now to pull the PA
Check the K3 Manual looking under the Menu Function
descriptions for SW TONES. It tells all.
73,
Ken K3IU
~
On 7/2/2013 6:14 AM, Joel Black wrote:
Can someone point me in either the manual or the Fred Cady
book where the different beeps issued by the ATU
testing with a separate receiver
(my K2) and see if I can duplicate it. I'll also re-read the
manual on the KAT500 to see if I can make it less sensitive
to in-band freq changes. I know that there are changes in
settings that can be made.
73, Ken K3IU
Try this URL...
http://www.elecraft.com/manual/K3_Schematics_Jun_2010.pdf
Ken K3IU
On 5/23/2013 9:01 AM, Dr. William J. Schmidt, II wrote:
H... I fix my own stuff, so my expectation is that a diagram show up
with my newly purchased KPA500
Hi Tom:
See page 11 of the manual.
73,
Ken K3IU
~~
On 1/29/2013 11:41 AM, Thomas Lindner wrote:
Hi,
my KAT500 works fine without any problems. It is connected to the K3 via the
DB15 interface cable. There is no KPA500 in the chain.
Today I noticed
G'morning:
In case anyone is still wondering about shipping status of
the KAT500, I placed an online order on Sunday afternoon.
Monday afternoon I received an email saying it had been
shipped. I'll have it here in RI on Wednesday.
73,
Ken K3IU
, the current
will be displayed. If I again tap the CURRENT button, the
display shows the band info, not the HV.
73,
Ken K3IU
On 12/27/2012 1:00 PM, Jack Brindle wrote:
Tapping a button on the KPA500 causes the parameter associated with that button
to be displayed. Try
for the
current parameter to show the band?
Interesting...
Jack B, W6FB
On Dec 27, 2012, at 10:21 AM, Ken K3IU kenk...@cox.net
mailto:kenk...@cox.net wrote:
Hello, Jack:
Mine doesn't work that way at all. On s/n 108 with
firmware 1.18, if I have PWR selected and tap HV, I see
the HV on the display
.
Anyway, that's enuf from me. It's Miller time here on the
east coast.
73,
Ken K3IU
~~~
On 12/27/2012 3:08 PM, Jack Brindle wrote:
Ken;
My fault. My description was a bit foggy. When you tap a
band button, it changes the display parameter to the
band
http://www.elecraft.com/manual/E740107%20K3%20Owner%27s%20man%20D10sm.pdf
73,
Ken K3IU
On 11/23/2012 7:39 AM, Ray Fallen wrote:
Good morning...
I'm picking up a gently used K3 and P3 combo on Saturday and trying to get
ready to use it ASAP.
Which Heil boomset
Just worked him at 1512Z. Note sounds fine to me.
73,
Ken K3IU
On 7/29/2012 10:51 AM, Rick Stealey wrote:
Anyone notice the CY9M cw note sounds choppy, or is it just me?
On 10.116 as I write this at 14:50 Z.
Rick K2XT
Page 8 of the Owners Manual... Specifications. 11V Minimum.
73.
Ken K3IU
On 6/28/2012 2:07 PM, Peter Wollan wrote:
The problem here isn't the battery AH capacity, but the voltage
supply. It could be dropping below 10 vdc because both radios
Check the Troubleshooting Section of the K3 Utility Help file.
73, Ken K3IU
On 5/11/2012 11:40 AM, Phil LaMarche wrote:
Attempted to download new version and the utility wouldn't connect to K3.
Tried to turn off but only MCU LD showed in the window. Removed
on the two
frequencies. I checked at low power (5W), mid power (60 W)
and 100W. The needle on the meter doesn't move when I key
the FSK input.
It is not my intent to start an argument about this, but
just thought you might want to know my observations.
73, Ken K3IU
Bi Bruce:
Go to the web site, click on the Firmware menu item, then
the K3 where you will see the info on the 4.48 firmware.
73, Ken K3IU
On 3/2/2012 3:39 PM, Bruce Beford wrote:
I notice beta firmware 4.48 (uploaded 2/29/2012) on the ftp site. The
release notes only list changes through 4.47
A
display will not change in split mode to the TX freq, since
it is already shown on the display.
73, Ken K3IU
~~
On 1/28/2012 4:40 PM, ke2sk wrote:
I recently assembled the K3 with just the ATU as an added option no sub rcv.
In trying to run in SPLIT mode SSB I set
G'morning, all:
In case anyone is keeping score, I shortened the 5/16
screws that support the PA module on the Z bracket and the
Right Hand Panel, reinstalled them and now no longer have
thermal expansion clicks/ticks/pops of any kind as the amp
heats up(tested to 65C) or cools off. I had
If there is not a felt washer between the VFO knob and the
panel, then that is your problem. I have never experienced
the noise that you describe after operating about 6
different K3s.
73, Ken K3IU
On 12/13/2011 11:03 AM, Natan Huffman
Hi Mike...
Just to give you another data point, I have no problems
doing the TX Cal on 6 meters. Using about a 6 foot length of
RG-213 to an old Heath Cantenna. Works fine at both 5 watts
and 50 watts.
Good Luck...
73,
Ken K3IU
On 11/8/2011 12:46 PM
Input Voltage Selection that The power supply is
set up for 230V AC input as shipped from the factory. It
continues with a description about how to change it to 115V
AC. I can't find it now, but I'm sure there was also a
separate insert on bright paper warning that it was set for
230V AC.
73, Ken
.
73,
Ken K3IU
Portsmouth, RI
On 6/29/2011 3:35 AM, Bruce Beford wrote:
I'd like some confirmation of this. I can see in the KPA500 manual (rev A,
page 16) that pin 11 of the AUX connector is INHIBIT#. That's fine. Pin 11
on the K3 AUX connector is DIGOUT1, OK. However, also in the KPA500 manual
This is what it ways on the order page under options...
*KTCXO3-1TCXO * *(0.5 ppm typ) High Stability Ref.
Osc. $99.95
*73,
Ken K3IU*
*
On 6/2/2011 6:02 PM, Daniel Allen wrote:
Forgive me if this has already been discussed, but will the KX3 have a 0.5
ppm TCXO? If so
If there is anyone out there who has set up one of the
Elecraft XVs with a FT1000MP, I would appreciate hearing
from you. I built a XV222 for a ham friend with a MP (I
don't have one) and am not having good luck with the -6dBm
signal level that is indicated in the MP manual. (I'm
testing with
Oops! Never mind. I had one jumper in the wrong position :-((
73, Ken K3IU
~~
On 3/5/2011 8:03 AM, Ken K3IU wrote:
If there is anyone out there who has set up one of the
Elecraft XVs with a FT1000MP, I would appreciate hearing
from you. I built a XV222 for a ham friend
Geoff:
I had this same problem back in mid October 2010 (may still
have it... I just haven't tried to do the RF Cal recently)
and swapped several emails with Dick Dievendorff on the
subject. We came up with nothing and he was going to confer
with Lyle when he got back from vacation.
Geoff:
I had also forgotten that I had installed the upgrade to the
K3 Utility. I just ran the test and it worked properly on
both the main Rx and the Sub Rx using v 1.3.11.5.
Sorry to have bothered you, Dick...
73,
Ken K3IU
~~~
On 1/9/2011 3:50 PM, Ken K3IU wrote
G'morning, Guy:
CW Mode, 400 Hz bandwidth with 400Hz filter, AGC-F, abt S3
noise level, NR ON, NR setting=NR F 1--2
Guess about a half second. Not a complete audio reduction to
no sound at all, but a perceptible momentary reduction of
the sound.
73, Ken K3IU
No, Guy, I don't use NR in a contest. I hardly ever use it
at all. Tony was looking for some input, to I tried it out
and told him what I found. This is NOT a problem for me at all.
73, Ken K3IU
On 12/14/2010 11:05 AM, Guy Olinger K2AV wrote:
Well, I
, switching back
to Preset I produces a quiet Rx with only the popping when
the APF Shift or Width being rotated.
73,
Ken K3IU
On 11/6/2010 7:46 AM, Len, K3LJ wrote:
Gentlemen, thanks for adding the APF to the K3 and the quick response to the
bug that some operators were experiencing. The APF
,
Ken K3IU
On 11/6/2010 8:37 AM, Ken K3IU wrote:
K3 #202, MCU 4.18, et al.
Similar experience here. Everything normal until I rotate
the APF Shift CW and it reaches 1.00 the loud pops/cracks
begin when rotating both the Shift and Width knobs
More tests... My previous report was with the sidetone set
to 600 Hz. I set my sidetone pitch to 670 and the point at
which the APF returns to normal moved up to .27 (270 hz). I
now hear the same boop as Nate reports and a return to
normal .
73, Ken K3IU
Mal:
I've had a similar problem when using the XG1 to run the RF
Calibration on the SUB Rx (Main works fine). Dick
Dievendorff (author of K3 Utility) is aware of the problem
and will hand it off to Lyle when he gets back from vacation
shortly.
73,
Ken K3IU
On 10/21/2010 7:08 AM, Malcolm
I forgot to say that I am NOT using the P3... just the K3.
73, Ken K3IU
On 10/13/2010 5:05 PM, Ken K3IU wrote:
I'm also running 4.14 and when using HRD, I see the same
thing W3CCS reports. The radio jumps to the frequency that
was double clicked and then almost immediately returns
Oops... the report below was with the K3 on 10m and the
frequency being clicked on was on 15m. I just tried clicking
on a 10m spot with the radio on 10m and it works correctly.
73, Ken K3IU
On 10/13/2010 5:06 PM, Ken K3IU wrote:
I forgot to say that I am
with no
problem. Six meters used to not be able to do that, but a
recent firmware upgrade solved that problem on 6 meters.
73,
Ken K3IU
K3 #202
~
On 9/13/2010 8:51 AM, John Ragle wrote:
Referring to my K3/100 Ser. No. 4103:
What, exactly
Tapping display does not cause the display to alternate between date and
time. It simply turns whatever you have selected on/off. The only to
change from time to date is to use VFO B knob.
73,
Ken K3IU
~
On 8/11/2010 11:17 AM, Roy Morris wrote:
I must be missing
This function is available in the CONFIG menu [CONFIG:SPKR+PH] which can
easily be assigned to one of the programmable buttons on the right hand
side of the K3 Front Panel. It works great! I have mine on M3(Hold) and
it cycles between speaker and phones and just phones.
73,
Ken K3IU
Have you recalibrated the S-meter since you did the RF Gain Cal on the
K3? I found that to be necessary.
73,
Ken K3IU
~~~
On 4/24/2010 8:36 AM, Ian Maude wrote:
Hi all,
I have been playing with the RF gain calibration procedure on my K3. I have
used my XG1
It works. You have to be sure you have the Sub Rx turned ON when you
attempt to turn NR on or off using b-set
73,
Ken K3IU
K3 #202
On 1/26/2010 8:58 AM, Don Wilhelm wrote:
Jim,
In that case it should work. Is there any chance you are in either DATA
or FM mode
With Sub Rx ON, I can toggle NR ON/OFF in Sub Rx using bset. This does
not affect the ON/OFF status of the Main Rx. However, when I change the
NR setting (press/hold NR) of the SubRx, that changes both the SubRx and
Main Rx setting... just as Werner reports below.
73,
Ken K3IU
,
Ken K3IU
~~~
On 1/10/2010 5:08 PM, Gilbert Cross wrote:
The 12 to 14 days is the time they say they need to get them in
house. I too have a set ordered and am about to call to check on my
order
73 Gil K8eag
For some additional info, I
be another fix now
that I don't know about.
73,
Ken K3IU
~~
On 1/6/2010 6:55 AM, Giulio Pico - IW3HVB wrote:
Yesterday I paid a visit to a firnd, Giancarlo I3GKK, who was very
worried about an accident happened 3 days ago.
Suddenly, during a brief tx period (10
Hmmm... it works here by just tapping the SUB on and setting CONFIG:
SUB to Balanced. Inner knob (Main AF) controls the overall volume level
and outer knob (Sub AF) controls left-right balance.
73,
Ken K3IU
Portsmouth, RI
On 12/27/2009 11:09 AM, Vic K2VCO wrote:
Don Wilhelm wrote:
You
When in the CONFIG mode, simply tap the DISP button and you will see the
Default value for the selected parameter. It is also in the manual for
each parameter.
73,
Ken K3IU
~~
On 12/23/2009 9:29 PM, Jay Rodaman wrote:
Perhaps I stated the question incorrectly
John:
Off the top of my head, the only thing I can offer is to remove all
external connections from the K3, except the power cord and a dummy
load. Also, if you are using a USB-to-9 pin adaptor and you have the
ability to use a traditional serial cable, try using that.
73, Ken K3IU
The price hasn't changed. Still free shipping. I ordered one on 12/4/09
shortly after I got their email and it is still listed as on backorder.
73,
Ken K3IU
~
Gary W. Marklund wrote:
I had them on watch at BH and received an email about a week ago
Mike:
I had same thing here. If you have MAIN:MIC+LIN set to ON, try turning
it OFF or unplugging the Line In. That fixed my problem, but I haven't
determined why Line In is causing that problem.
73,
Ken K3IU
~
Mike wrote:
Don -
I'm using phones. It doesn't
I forgot to mention that it is NOT RF here, 'cuz it happens in TEST
mode with no RF out.
73, Ken K3IU
Ken K3IU wrote:
Mike:
I had same thing here. If you have MAIN:MIC+LIN set to ON, try turning
it OFF or unplugging the Line In. That fixed my problem, but I haven't
phone, but glad I fixed it anyway ;-) .
73, Ken K3IU
~~~
Mark n2qt wrote:
Be sure you don't have a 'sneak path' through a computer sound card (or
other accessory) via line out to line in on the K3.
Mark n2qt
- Original Message - From: Ken K3IU kenk...@cox.net
Original Message
Subject:Re: [Elecraft] Dumb user mistake - slow transition between Tx
and Rx
Date: Mon, 09 Nov 2009 07:35:36 -0500
From: Ken K3IU kenk...@cox.net
To: Dick Dievendorff die...@comcast.net
References: 200911090302.na9325hw086...@www6
Nothing here on #202.
73, Ken K3IU
~~~
K2QI wrote:
No one has experienced anything similar? I'm surprised...
James K2QI
On Mon, Oct 26, 2009 at 9:07 PM, James Sarte k2qi@gmail.com wrote:
My 4 knobs (filter shift, width, mic, and pwr) have developed what seems
the right order of magnitude???
Thanks...
Ken K3IU
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http
You need to make sure both VFO A B are in the same mode, else you will
get N/A.
Ken K3IU
Steve Ellington wrote:
How are you getting split in data A? When I push SPLIT I get SPL N/A.
Steve
N4LQ
n...@carolina.rr.com
- Original Message -
From: Chuck - AE4CW ae...@att.net
I also noticed this the other day when I was messing about with the RF
Gain Calibration and then wanted to recheck the S-meter calibration.
Thought I probably had a button-push sequence messed up, but I wasn't
able to finish the job for the SubRx.
73,
Ken K3IU
Mike
to have a separate
adjustment for the SubRx S-meter. I'm sure the manual will catch up.
73,
Ken K3IU
~~
N1JM wrote:
There is an error in the manual according to Wayne and you cannot calibrate
the sub rx S-meter.
John N1JM
Mike Harris wrote
Try the N1MM Users Manual. Section 41 - Multi User Support.
73, Ken K3IU
Stephen Reichlyn wrote:
Can anyone give me a thumbnail review of how to use N1MM with 2 K3s in
multi/2 (or tell me where to find the info?)
73,
Steve AA4V
According to the Release Notes, this wasn't implemented until FW
release MCU 3.19 / DSP 2.17.
73, Ken K3IU
~~
Thomas Lindner wrote:
It seems to me, the ML command to get and set the Monitor Level is
not working.
MC: 03.14
Any ideas?
Tom, DL2RUM
I haven't seen it mentioned, but I'm seeing the same thing.
73,
Ken K3IU
~~
bearcat wrote:
I loaded the new firmware and the DSP is 2.24, the web site show 2.25.
The FW is 3.27.
I hope I did not miss this mentioned already
You probably inadvertently set your PITCH to 610. Try resetting it to
600 and see if that solves your problem.
73, Ken K3IU
Brian Pepperdine wrote:
I have noticed what I think is small but inexplicable change in my K3 shift.
Up until a few weeks ago (when I had some other odd issue
1 - 100 of 283 matches
Mail list logo