G'day,
Did you have a light shining on the PA transistors? J3+ on my KPA100
had -0.18V. Apparently something to do with illumination of the PA's.
Well noted by others.
Regards,
Mike VP8NO
- Original Message -
From: Gerhard Schwanz [EMAIL PROTECTED]
To: elecraft@mailman.qth.net
G'day,
#1400 @ 100W did a little SP on 14/21/28 MHz.
I was only looking to see how many states I could snag in between doing
other stuff during a wonderfully sunny weekend. I ended up with 30 states
plus two provinces out of 104 exchanges plus a few others heard in
pile-ups but not worked 'cos
G'day,
And it lives about 60 metres east of #1400.
Now about this strong signal handling business.!
Regards,
Mike VP8NO
- Original Message -
From: Chris [EMAIL PROTECTED]
To: Elecraft@mailman.qth.net
Sent: Tuesday, March 01, 2005 11:47 AM
Subject: [Elecraft] K2 4768 arrives in
G'day,
#1400 (100W) accidentally found itself in a run situation in the ARRL DX
SSB contest on 10 metres. Anyway, buzzing along at about 120/hour
according to the logging program and a couple of complimentary comments
about the audio quality (late model KSB2 and Kenwood MC-42S mic). I was
G'day,
snip
Personally I'd rather be told that I sounded like Roger Daltry than Mic
Jagger
(similar vintage - different ageing process).
snip
snip
Perhaps you are more familiar
with the other leading personality from that group, Pete Townsend
snip
Correct. I have a bit of a hole in 70's
G'day,
| You're probably hearing Russian military HF channel marker or
| propigation beacons.
|
| More information at:
|
|
http://www.smeter.net/propagation/beacons/7039.3-k-Petropavlovsk-Kamchatskiy.php
Interesting this. Information I have gives the location of K to be
Khabarovsk, Asiatic
G'day,
There's at least two ways of looking at that. Good luck never the less.
Regards,
Mike VP8NO
snipo
Hi friends!
I feel like a woman who knows that she will soon be pregnant!
I just ordered a K2!
Yves Dussault-VE2ATD
Laval, Québec.
450 661-0768
snipo
G'day,
PC mother boards are stuffed with them, I got mine from a junked PC.
Didn't need the option the solder to them.
Regards,
Mike VP8NO
snipo
The '2 pin computer jumper blocks' used to program the microphone on
the SSB board are probably familiar to us all, however, how does one find
G'day,
All I do is common the individual power leads to the K2 and external
KPA/KAT at the power supply. Seems the simplest thing to do and ensures
the correct power up sequence. No diodes required, no voltage drop on the
KPA lead passed through to K2. Things can be made too complicated,
G'day all,
All this talk about 800W amps is interesting, however, due to oil prices
the power company here has had to shove up the price per kWh to about 27c
US. I'll stick with more and better high level aluminium which sucks as
well as blows. Less potential TVI too.
Regards,
Mike VP8NO
G'day,
in it. By the way, I'm presently installing the KIO2 interface in my
K2
and will use my Palm 105 (PDA) to control the K2. I will be able to
change bands, frequencies and send cw from preloaded messages in the
Palm - neat! The Palm 105 will even log and dupe for me! I then
Hot-Sync
the
G'day,
After some more debugging it appears that the ksb2 is causing the
problem.
Removing it returns tx power to normal levels. Some might say, good
you
don't need ssb anyway.
Sounds somehow familiar. Check the resistor packs.
Regards,
Mike VP8NO
Interesting but badly out of focus, detail lost.
Regards,
Mike VP8NO
| In spending some time reviewing the placement of the K3's SO-239
connectors,
| the RF connector mounting configuration can be improved with only minor
| re-work as shown below. In the link to the following photo, you will
Hi,
Curious to note that when working split the bandmap in Logger32 doesn't
show the switch to VFO-B. Pressing the REV button causes the bandmap
cursor to move but not during keying. With the K2 you could see your TX
frequency change when in split.
Regards,
Mike VP8NO
G'day,
Anyone seen a photo of the KRX3 yet?
Regards,
Mike VP8NO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
Good day,
Recently I noticed a brief flash of ERR PL1 when changing from 17M to 15M.
It happened maybe a dozen times. Not noticed before, not noticed since.
I didn't record the exact frequency this was happening on.
PLL 1 voltage on 15M:
21.000 5.2
21.050 5.5
21.100 5.8
21.150 6.0
21.200
Hi,
I've no idea how I did it but does anyone know how to kill off the antenna
name display when switching from ANT1 to ANT2 or back?
Can't find it in the handbook.
Regards,
Mike VP8NO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
how to turn it off. Maybe the great and good who programmed this can
offer an answer. Maybe once you've set it you're stuck with it, I don't
want it.
Regards,
Mike VP8NO
- Original Message -
From: Bill Coleman N2BC [EMAIL PROTECTED]
To: Mike Harris [EMAIL PROTECTED]
Sent: Friday, April
Hi,
No only does it show when switching from ANT2 to ANT1, it shows every time
you change band where ANT1 is the currently selected antenna port.
I've tried restoring from a previous configuration, alas, no change.
Regards,
Mike VP8NO
___
Elecraft
G'day,
Some of us have been asking for years for the individual K2 VFO's to
remember the mode they were last used on. On the list I believe.
Despite all the bells and whistles, I've yet to find anything I can't hear
on the K2 as well as I can on the K3. It's taken me a while to make the
K3
G'day,
- Original Message -
From: Joe Subich, W4TV [EMAIL PROTECTED]
To: 'wayne burdick' [EMAIL PROTECTED]; 'Elecraft Reflector'
elecraft@mailman.qth.net
Sent: Sunday, May 04, 2008 1:24 PM
Subject: RE: [Elecraft] K3 FIRMWARE UPDATE: MCU 1.87, DSP 1.69 (Finally!)
| * AUTO-SPOT
G'day,
I've just noticed that with the latest firmware installed the previously
enabled antenna name feature (HOLD ANT) has been cancelled. I'm loathed
to try setting it again 'cos I don't want it. Is there a disable method
just in case in the heat of something I accidentally turn it on
G'day,
- Original Message -
From: wayne burdick [EMAIL PROTECTED]
To: Nick Henwood [EMAIL PROTECTED]
Cc: elecraft@mailman.qth.net
Sent: Sunday, May 04, 2008 6:13 PM
Subject: [Elecraft] Re: K3 Second Receiver
| No. Our sheet metal fabricator was sick for a week, and he didn't get a
|
Hi,
I put my K2 #1400 back on line last night to have a listen around 40M CW.
I'm getting a bit fed up with one step forward, half a step back firmware
upgrades and am giving it a rest for a while. Anyway, I was surprised
just how nice it sounded compared to my K3. The audio seems softer and
G'day,
| This isn't the case at all. We have 20 beta testers who work tirelessly
| testing interim releases. They're doing it as we speak. They pounded on
| rev 1.87 for three weeks.
But with respect to all concerned they apparently didn't spot that VOX was
broken. Not subtle that one.
G'day Mike,
No point in checking past settings. All has changed with the latest
firmware. AF response, mike gain, VOX settings etc. You just have to
start again.
Regards,
Mike VP8NO
- Original Message -
From: Mike Kasrich [EMAIL PROTECTED]
To: Elecraft elecraft@mailman.qth.net
G'day,
| n4lq wrote:
|
| The K3 has the cleanest receive audio I've see thusfar.
|
| I'm likewise a bit skeptical (but I could be wrong) about the alleged K3
rx
| audio issues. My experience is that the K3 rx audio is more
transparent
| and thus any problems with the other guy's audio will
I am unworthy.
Regards,
Mike VP8NO
- Original Message -
From: Bob [EMAIL PROTECTED]
To: Mike Harris [EMAIL PROTECTED]; elecraft@mailman.qth.net
Sent: Monday, May 12, 2008 5:44 PM
Subject: Re: [Elecraft] receiver distortion
| No wonder it sounds poor Your using the cheap junk
G'day,
snipo
So, if we are going to annoy someone, that means we can't do it?
What? Then we shouldn't be working on getting into space, that is likley
to annoy
someone... the folks that live there for one...
snipo
Too right. The surest sign that there is intelligent life out there is
that
Hi,
Anyone else seeing a birdie on 28004.9+/-?
With no antenna, CW, 500Hz hardware filter, 50Hz DSP, I see DISP readings:
-21dBV pre-amp OFF
-1.4dBV pre-amp ON
In either case the ATT makes only another -2dBV difference.
It doesn't display on the S-meter but given many workable signals don't
Hi,
No big deal, it just gets in the way occasionally, just like a similarly
placed offering in the K2, albeit that one has a different source. For
what it's worth, I've been working signals on 10M this weekend somewhat
lower in strength than this particular birdie. No band noise at all when
Hi,
Yes, why would you want it to stay on when changing band or QSYing. Both
result in a whole new scenario where RIT or XIT are probably not required,
at least initially.
Also with regards to memory management, I certainly don't want a load of
nanny steps to stop me mucking it up. As has
Hi Drew,
- Original Message -
From: [EMAIL PROTECTED]
To: elecraft@mailman.qth.net
Sent: Friday, May 30, 2008 10:20 AM
Subject: Re: [Elecraft] K3 Band changing...Devils Advocate...
|I don't have a K3 yet but I'm happy with the Band+ and Band- buttons
| on my K2. I pretty much know how
Hi,
Not sure if the question was answered.
To turn the fans on manually: CONFIG KPA3: VFO A from PA nor to Fn
1 through Fn 4
The setting sticks when you come out of CONFIG and through a power ON/OFF
cycle.
Regards,
Mike VP8NO
- Original Message -
From: hank k8dd [EMAIL
Hi,
I use an MC-43S with MAIN menu setting FP.H for high gain. Manual p.49
MIC SEL
Regards,
Mike VP8NO
- Original Message -
From: Dick Dievendorff [EMAIL PROTECTED]
To: 'VE7AJJ' [EMAIL PROTECTED]; elecraft@mailman.qth.net
Sent: Saturday, June 07, 2008 7:01 PM
Subject: RE: [Elecraft]
Hi,
Unless I'm misunderstanding something it works here.
SSB - PTT mode, press paddle whilst in RX results in CW with RF output.
Interestingly this happens even if true CW mode is not set to VOX.
Is this somehow broken in v2.02? I haven't bothered to load it yet
because it doesn't offer me
- Original Message -
From: Tom Childers, N5GE [EMAIL PROTECTED]
To: Elecraft@mailman.qth.net
Sent: Saturday, June 14, 2008 10:29 AM
Subject: Re: [Elecraft] K3 - v2.02
On Sat, 14 Jun 2008 10:14:24 -0400, Mike Harris
[EMAIL PROTECTED]
wrote:
Good day,
I upgraded my firmware to v2.02
- Original Message -
From: Dave G4AON [EMAIL PROTECTED]
To: elecraft@mailman.qth.net
Sent: Saturday, June 14, 2008 5:10 PM
Subject: [Elecraft] Fw: K3 - SSB levels
| Julian
|
| I've noticed a similar odd issue when using the Winlink program
| Airmail, after quitting the HF module the K3
Good day,
Could someone please test the Antennex URL:
http://www.antennex.com/shopping.htm
With that or even http://www.antennex.com all I can get is a warning about
not mass downloading with no further access.
The reply I received to a direct query is:
It's something, like an addon in your
Good day,
Many thanks to all who replied. I have tested with our ISP and they get
the same result as I do using IE6 IE7. Mozilla seems to work OK.
Very odd. They use some pre fetch for their cache but you would think
that would affect both browsers. I routinely scan for spy-ware.
Anyway,
G'day,
I would go along with that. Unwanted memory contents is just untidy.
Regards,
Mike VP8NO
- Original Message -
From: Brett Howard [EMAIL PROTECTED]
To: elecraft@mailman.qth.net
Sent: Sunday, June 22, 2008 1:22 AM
Subject: [Elecraft] K3 Erase Memories
| Is there a way to erase
G'day,
And why do the 1000+ worldwide subscribers to this reflector need to be
belaboured by this love-in stuff which has nothing whatsoever to do with
Elecraft products or their use?
Regards,
Mike VP8NO
- Original Message -
From: Bruce Bowman, NM5B [EMAIL PROTECTED]
To:
from others!
Regards,
Mike VP8NO
- Original Message -
From: Brett Howard [EMAIL PROTECTED]
To: 'n4lq' [EMAIL PROTECTED]; 'Mike Harris'
[EMAIL PROTECTED]; Elecraft@mailman.qth.net
Sent: Monday, June 23, 2008 7:55 PM
Subject: RE: [Elecraft] No field day this year for W0CZ
| Many tune
G'day,
Astonished by all this. I've never moved my K3 merely by pressing the
front panel buttons. Anyone hitting them that hard won't be doing them
any favours.
Regards,
Mike VP8NO
- Original Message -
From: Ron D'Eau Claire [EMAIL PROTECTED]
To: 'Elecraft Reflector'
G'day,
Tested again. With 2.13 6M CW memory saves return REV. Maybe this only
happens with saves after 2.13 has been installed and not with prior saves.
Regards,
Mike VP8NO
- Original Message -
From: WA6OCP [EMAIL PROTECTED]
To: elecraft@mailman.qth.net
Sent: Friday, July 04,
G'day,
I've always thought of it as the next band UP or the next band DOWN
determined by frequency, so the current legend is perfectly correct in
that context. Just one of those conventions I guess, suits me.
Regards,
Mike VP8NO
- Original Message -
From: Brian Alsop [EMAIL
G'day,
Interested in what power level is required to trigger the carrier operated
relay in the KRX3. Just out of interest I've checked the coupling between
my OB9-5 and the OB5-6 about 2.4 metres above it, booms in-line.
900W into the HF coax, terminated WM-2 on the 6M coax. worst case 45mW
G'day,
| 160 is the longest wave hams can use, hence it's the top band.
|
| 73 de Jim, N2EY
137kHz = 2188 metres
Regards,
Mike VP8NO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber
Hi Al,
No.
It is also wise to re check REF CAL after maybe a year of burn in.
I re did mine after about 1-1/2 years and I had to retune approx
50Hz lower. Only to be expected.
Regards,
Mike VP8NO
- Original Message -
From: Al Lorona alor...@sbcglobal.net
To: Elecraft Reflector
G'day,
Just received and installed the KXV3A Upgrade. Oddly you receive
the whole KXV3A package including PCB, connector panel, TMP cable
and hardware. For an upgrade only the PCB is required.
When reinstalling the KIO3 assembly the TMP cable to the KXV3A has
to fit in a notch in the KIO3
G'day,
For what it is worth.
Just done a quick test with my K3/K2 combo.
K3 14020kHz. 50W into my beam.
K2 with no antenna connected receives a signal at S9+20 on the
S-meter. Keying at 14013.67kHz and 14026.38kHz was heard.
Additionally I heard signals at 14007.24kHz and 14000.99kHz,
G'day,
Has anyone managed to use the proceedure in the handbook to
calibrater the sub-rx s-meter?
The metering is switched over to the sub-rx when in b SET mode.
However, as soon at you go into CONFIG the s-meter reverts to the
main rx making callibration impossible. This can be checked by
G'day folks,
Right, I have now been advised via several sources that the
independent callibration of the sub-rx s-meter is currently not
possible. Pity about the wast of time trying to do it as detailed
and wondering why.
Also I understand that the TCXO temperature data entry in the latest
G'day,
My results are:
Source - XG1, RX gain calibration per the utility routine:
Subsequently:
Main RX only, pre amp OFF - 50uV (S9), 1uV (S2)
Sub-RX ON therefore splitter loss:
Main RX S8 S1
Sub-RX S7 S0
No big deal but not identical.
As a matter of interest, the S-meter on the main
G'day,
Would this module be available already fitted to a swap out DSP
board?
Regards,
Mike VP8NO
- Original Message -
From: Wayne Burdick n...@elecraft.com
To: n...@no3m.net
Cc: elecraft@mailman.qth.net
Sent: Tuesday, October 13, 2009 2:31 PM
Subject: Re: [Elecraft] K3 Rev C DSP
G'day,
I understand from a previous post that memory is maxed out. Also
that a possible pin compatible micro with more memory is a
possibility. I have offered the idea that pruning the rather
generous CW memories might offer up enough memory with the existing
micro for the update you
G'day,
Over spec'ed and over price for such a simple job.
Regards,
Mike VP8NO
- Original Message -
From: Don Wilhelm w3...@embarqmail.com
To: elecraft@mailman.qth.net
Cc: Ken Adams K5KA kfiv...@gmail.com
Sent: Friday, October 16, 2009 3:34 PM
Subject: Re: [Elecraft] K3 Aux I/O and
G'day,
A contrary opinion, yes it is noticeable, particularly when trying
to work signals near the noise. I usually have to crack where the
callers are going through and then toggle the sub-RX off to make
sure I have good copy on the target. In some circumstances I still
find that using REV
G'day,
3. Logging/control software assumes that we'll be operating split
in the
way the transceiver manufacturer intended. Anyone trying to fight
that
could easily wind up calling on the DX frequency.
Logger32...?
Regards,
Mike VP8NO
G'day,
Don't you get the feeling that a six month hold on new frills is in
order. Polish up what's already there. It's all getting a bit
manic. I certainly don't need a radio that tries to out guess me.
Damned if I would want to fly in something that reconfigured itself
without direct
G'day,
A few weeks ago someone posted a link to tranceiver project that had
RS connections. Unfortunately I didn't save it. I would be
grateful if you could send me the link.
regards,
Mike VP8NO
__
Elecraft mailing list
Home:
Hi Gary,
Join the club. I've been having random low audio on switch on for a
while now. Switching off and then back on again restores volume.
Regards,
Mike VP8NO
- Original Message -
From: rfenab...@gmail.com
To: Elecraft Elecraft@mailman.qth.net
Sent: Wednesday, October 21, 2009
G'day,
Don beat me to this. However, I would like to add that the
calibration of the TXCO is not a one off event. When I checked the
calibration after a years worth of burn in I had to adjust the TXCO
lf by about 50Hz. How much this translates into a dial error I've
no idea, I've not
G'day,
Had quite a bit of snow static when I was in Antarctica. The
protection bulb in the front end of the FT-101 used to glow gently.
It survived the whole two years. Simple but it worked.
Regards,
Mike VP8NO
__
Elecraft
G'day,
Quite. I believe my K3 will remain a macro free zone. Can't see
the point.
Regards,
Mike VP8NO
snip
I think the ideas for all the additional Macro memories are great,
but
ultimately remembering what Macro is where becomes the limiting
factor
(at least for those terribly
G'day,
Cold with occasional snow, so what to do? Install a rather overdue
CW Keying Rise Time mod.
Decided to install the SMD cap, getting good at this. All went
well, all buttoned up. Test radio, not so good, no output on CW. A
flash of memory of a posting of a month or so ago, check the
G'day,
snip
There are four cover holes where you're instructed to remove
the paint from the area around them so the stand-offs can
make a good ground connection. The paint is tough, and
requires hard scraping to remove. A small scrap of masking
tape over the four areas before painting, as
G'day,
Seems too complicated. My general coverage module is in the main RX
and I tune with VFO A. VFO B always has a return frequency and a
simple A/B and then AB sorts things out.
It does it for me.
Regards,
Mike VP8NO
- Original Message -
From: Joe Planisky jp...@jeffnet.org
G'day,
The technique probably has other applications, like controlling
filters or preamps, etc.
A new MP command allows you to set the DIGOUT1 control line (pin
11 of the K3 accessory
connector) to go to ground. This line is per-band and per antenna.
This line can sink only
15 ma, so I
G'day,
Some of the down-market adapters have poor shield attachments.
Could
it be that in handling your adapter, you caused the shield to
loosen
up or detach at one end or the other (of the cable)?
The KUSB doesn't have this problem, btw.
matt W6NIA
Nevertheless the KUSB does
G'day,
6M configuration:
5el Yagi at 50 feet, approx 150 feet of Ecoflex 10 coax 1.5-2dB
loss. K3 with PR6.
Antenna pointing north over the harbour and open country, no S-meter
reading but upon removal the antenna RX noise fell by 8-9dB as
displayed by the K3 dBV. (PRE and PR6 on, 400Hz
G'day,
I guess some folks just treat the gear rough and Gorilla the screws
down. I was surprised to see a bug being knocked about the table in
the K5D video.
Regards,
Mike VP8NO
K3 #345 (original knobs)
- Original Message -
From: Julian, G4ILO julian.g4...@gmail.com
To:
G'day,
If I post something to the UK it is usually delivered within five
working days of departing VP8 (including a day in the air). When I
order anything from Elecraft it takes 2-3 weeks to arrive, always
has done. All my Elecraft stuff comes air letter post (expensive)
because the US
Hi Don,
Stick to the K2, you know something about that.
Regards,
Mike VP8NO
- Original Message -
From: Don Wilhelm w3...@embarqmail.com
To: Mike Harris mike.har...@cwimail.fk
Cc: elecraft@mailman.qth.net
Sent: Friday, December 04, 2009 10:56 AM
Subject: Re: [Elecraft] Obtaining spares
G'day,
The simple fact is that the faithful will always suggest that the K3
hears more, is more sensitive or is more transparent to band noise
etc etc. Also you have to fiddle with the AGC, PRE, ATT and RF gain
whereas other radios just sound nicer out of the box. I don't have
a problem
G'day Lyle,
Interesting news. I will discover if this is so in the next couple
of weeks, the new DSP board is in the post.
Regards,
Mike VP8NO
- Original Message -
From: Lyle Johnson k...@wavecable.com
To: elecraft@mailman.qth.net
Sent: Wednesday, December 16, 2009 2:45 PM
Subject:
G'day,
I think that 30dB isolation across a single small PCB mounted relay
is about as good as it gets. It's the same for the K2 ATU's.
Regards,
Mike VP8NO
- Original Message -
From: Steve Ellington n...@carolina.rr.com
To: K2MK k...@comcast.net; Elecraft Reflector
Splendid news, why obtaining it had to be like pulling teeth I
cannot fathom. The noisy RX thread would have dried up before it
reached the present head of steam.
Regards,
Mike VP8NO
- Original Message -
From: Joe Subich, W4TV li...@subich.com
To: k...@aol.com;
G'day,
Please correct me if I'm wrong but my understanding is that the
settings of the RX equaliser work within the DSP block and will do
little to suppress the higher frequency products that contaminate
the subsequent audio out of the DAC. This is the domain of the
analogue LPF module that
G'day,
Yes, both within the radio and in the handbook Menu Functions.
Sadly reading the handbook to find out how to use the radio and how
to connect it to the outside world is a minority pastime.
Regards,
Mike VP8NO
- Original Message -
From: Jay Rodaman k2...@optonline.net
To:
G'day,
Sounds like an open mic on 14243.82kHz Lots of voices, club
meeting?
Regards,
Mike VP8NO
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
G'day,
Just installed a shiny new revision D main DSP board.
Date and time needs resetting so decided to use the utility Date and
Time configuration option.
Selected Date and Time: Current UTC date/time and K3 date/time
displayed.
Selected Apply: Date updated but the K3 display oscillates at
G'day,
There is much to be said in favour of reworked boards. At least
they've had a good burn in to get rid of infant mortality. I recall
reading many years ago that general aviation folks often preferred
avionics that had been once through the repair shop.
Inevitably something has to be
There was a time, maybe 8-9 years ago when life was thought to be
too short for inventories, many just jumped in and got on with it, I
certainly did. 100% success.
All this chatter about truncated lines is just getting in the way of
building. And another thing, real men wind torroids ;-)
G'day,
Lionel-F6FCD wrote:
Who and how are you using Elecraft products with interfaces for
digi-mode
?
What are you doing with ? what kind of mode is interresting ?
And alsowhat kind of software.a lot are available on the
web
The interface I use for digital modes is simply
G'day,
It's not exactly rocket science, you take the front panel assembly
off, remove a board and replace it with the new one, replace the
front panel assembly.
The assembly manual covers the front panel work or maybe just
download the DVR installation manual it's got all the information
you
G'day,
Being retired my K3 is used every day mainly chasing down DX so more
listening than transmitting. I don't have any problem with the form
factor, suits me just fine, so does the K2 I built in 2000 and which
accounted for over 200 DXCC for me during its evolution from QRP to
QRO and my
G'day,
Being retired my K3 is used every day mainly chasing down DX so more
listening than transmitting. I don't have any problem with the form
factor, suits me just fine, so does the K2 I built in 2000 and which
accounted for over 200 DXCC for me during its evolution from QRP to
QRO and my
No.
Regarding the recent K3 audio file tests. If you want to hear the
difference an LPF can make try the K2 with and without the KAF2.
Regards,
Mike VP8NO
- Original Message -
From: Sam Morgan k5oai@gmail.com
To: elecraft@mailman.qth.net
Sent: Monday, January 11, 2010 9:26 AM
G'day,
| My 180' wire was resonant at about 2.2 mHz, where the SWR was around
1.4:1. Since signals
Spectacularly slow velocity of propagation there.
Here we are, custodians of a technical hobby, one that we have to achieve
qualification in for licensing and we can't get our units right. MHz,
G'day,
Maybe I'm blind but I cannot find much information on the utility of the
KDVR3. There doesn't seem to be any published specifications.
The last page of the installation manual refers you to detailed
instructions for using your digital voice recorder are included throughout
the K3
currently on the
site.
Regards,
Mike VP8NO
- Original Message -
From: lyle johnson [EMAIL PROTECTED]
To: Mike Harris [EMAIL PROTECTED]; Reflector Elecraft
Elecraft@mailman.qth.net
Sent: Sunday, December 07, 2008 5:49 PM
Subject: Re: [Elecraft] KDVR3
| 1.How many seconds of recording
G'day,
| The big M vs. small m is something I'm very aware of usually, but
I'm
| not sure what a big K indicates vs. a small k. I've always just
| considered either to mean kilo.
Most prefixes which make a unit bigger are written in capital letters (M,
G, T etc) and when they make a unit
G'day,
| Joe's ability to pull them out. The other bad thing was Joe was only
| able to work 4 JA's rather than the hoped for 100.
| One thing Joe told me was to NOT use functions on the K3 and KRX3 when
| transmitting.
Not a plumber his he.
Regards,
Mike VP8NO
G'day,
Anyone using the PRS 6m preamp got anything to say about their
experiences.
Regards,
Mike VP8NO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub,
G'day,
I think placing the 51 ohm resistors on top of the existing SMD's was just
for convenience. It makes little difference to the final result - 51 ohm
vs. 45 - 49 ohm.
Regards,
Mike VP8NO
- Original Message -
From: Bill W4ZV [EMAIL PROTECTED]
To: elecraft@mailman.qth.net
Sent:
Cosmic rays.
Regards,
Mike VP8NO
- Original Message -
From: Bruce McLaughlin bmcla...@bex.net
To: 'Dave Yarnes' w7...@cox.net; elecraft@mailman.qth.net
Sent: Tuesday, December 30, 2008 11:33 AM
Subject: RE: [Elecraft] Woke Up With A Headache--No K3 ATU
|I believe the digital gods
G'day,
Aren't there still some issues re VFO management when wide range tuning.
The band switching can go pear shaped.
Regards,
Mike VP8NO
- Original Message -
From: wayne burdick n...@elecraft.com
To: KM5Q k...@mac.com
Cc: elecraft@mailman.qth.net
Sent: Wednesday, December 31, 2008
G'day,
For a bit of balance. I've got a noise on 20M that has popped up
recently. Seems to be three tones with 340Hz and 212Hz spacing and about
30dB out of the band noise. The auto notch takes them all out after a few
seconds thinking.
Not tracked the source yet and there seems to be some
G'day Uli,
KEY OUT switches on tune on #345. That is how I tune my Acom 1000.
Regards,
Mike VP8NO
- Original Message -
From: Ulrich Quandt ulrich.qua...@online.de
To: elecraft@mailman.qth.net
Sent: Thursday, January 08, 2009 6:47 PM
Subject: [Elecraft] K3 feature request
Hi folk,
1 - 100 of 544 matches
Mail list logo
