i *did* put the smiley face :)
Dennis Saputelli
Ian Wilson wrote:
On 01:58 PM 8/06/2002 -0700, Dennis Saputelli said:
boy that's a great point pat
i do them on doubles a lot but might have blown it on multi if it ever
came up
of course a board shop would never let that get out would
Mr. Lyons,
Thanks for the advice. No, it is a double sided pth.
Regards
Ken
-Original Message-
From: Pat Lyons [mailto:[EMAIL PROTECTED]]
Sent: Friday, June 07, 2002 7:59 PM
To: Protel EDA Forum
Subject: Re: [PEDA] help, how do i make rectangular holes in components
and on the pcb
boy that's a great point pat
i do them on doubles a lot but might have blown it on multi if it ever
came up
of course a board shop would never let that get out would they ? :)
Dennis Saputelli
Pat Lyons wrote:
On Fri, 07 Jun 2002 10:29:42 -0400, Ken Henrich wrote:
Hi
I want to make
On 01:58 PM 8/06/2002 -0700, Dennis Saputelli said:
boy that's a great point pat
i do them on doubles a lot but might have blown it on multi if it ever
came up
of course a board shop would never let that get out would they ? :)
Wanna bet? On an early board I did (years ago) I forgot to pull
Hi
I want to make rectangular holes in pads for components with metal tabs. For
instance, a hole 40mils by 120 mils. Can this be done in Protel 99SE? BTW,
is hole the proper nomeclature for this?
thanks and regards
Ken
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* To post a
Ken, I've done this by creating cutouts of the proper size (tiny)
using say four 1mil holes on 5mil pads. I included on the Drill Drawing
a detail showing routing a rectangular cutout from these sets of
1mil holes. You _must specify_ Plate Through for all these special
cutouts. Note that you
Hello Ken,
Friday, June 7, 2002, 7:29:42 AM, you wrote:
Hi
I want to make rectangular holes in pads for components with metal tabs. For
instance, a hole 40mils by 120 mils. Can this be done in Protel 99SE? BTW,
is hole the proper nomeclature for this?
thanks and regards
Ken
The best way to do this is to call your fab and ask them how they want the
information provided.
A slot, or rectangular hole, is done at the fab by using a routing bit -
usually after the board is complete, but before finish plating and
masking. Your fab will have its own procedures and
I want to make rectangular holes in pads for components with metal tabs. For
instance, a hole 40mils by 120 mils. Can this be done in Protel 99SE? BTW,
is hole the proper nomeclature for this?
I've done this in the past by placing the appropriate track on the drill drawing
layer, then
: Re: [PEDA] help, how do i make rectangular holes in components
and on the pcb itself?
Hello Ken,
Friday, June 7, 2002, 7:29:42 AM, you wrote:
Hi
I want to make rectangular holes in pads for components with metal tabs.
For
instance, a hole 40mils by 120 mils. Can this be done in Protel 99SE
On Fri, 07 Jun 2002 10:29:42 -0400, Ken Henrich wrote:
Hi
I want to make rectangular holes in pads for components with metal
tabs. For
instance, a hole 40mils by 120 mils. Can this be done in Protel
99SE? BTW,
is hole the proper nomeclature for this?
thanks and regards
Ken
You didn't mention
11 matches
Mail list logo