New pid is available from WLL, I think it was something like $75. Did you test output side of PID when it should be sending current to the brew boiler, i.e. Are you sure it's PID and not giemme controller? Mine both failed within a few weeks of each other.
Best, bmc Sent from my iPhone > On Mar 20, 2016, at 09:08, Eric Christoffersen <[email protected]> wrote: > > > Hi Peeps! > > Why not test anyway? Well, there's lazy and there's lazy... If it works why > fix it? And if it works how can I debug? So I finally have an update. > > Machine worked fine for the past week, then today it wouldn't go above 194. > So my threshold for inconvenience has been met, grumpy without my 'spresso > and I can repro, I have a new element in hand, etc, etc. > > Started in to testing: > Both elements read 13.4 ohms. > When steam boiler heats it gets 115volts. > When brew boiler heats it gets 112.5 volts. > > Steam and brew boilers both heat right up quickly, just as always. > > I checked/wiggled the spade connectors and all were tight. > > The issue is this: once displayed temp gets to 194 the brew boiler stops > receiving current. When it drops below 191 or so the brew element gets > voltage again. The measured voltage doesn't match the little dot on the > display. > > So: this doesn't seem to be an electrical problem with the element. Seems > that my pid is slowly losing its piddedness. > > My pid is the Gicar with the BLUE LIGHTs. I went through the menu and all the > values are correct defaults. I was about to do a "reset" (hold ^, power on, > prs, release button and power off) but figured I should try machine first. > Machine happily heated to 199, then got stuck there. It looks like as soon as > pid goes from constant on to pulsing that the pulsing doesn't actually > provide any voltage. When temp dips below a certain point then pid leaves > pulse mode and machine heats again. > > Did the reset and machine now heats to 202. > > Any ideas show of getting yet another pid thingy? > > Thanks! > Eric > > >> On Saturday, March 5, 2016 at 8:53:13 AM UTC-8, bmacpiper wrote: >> >> Why not test anyway? >> b >> Sent from my iPhone >> >>> On Mar 5, 2016, at 08:13, herman dickens <[email protected]> wrote: >>> >>> Don't worry it will come back. lol Good luck, hopefully it's something easy. >>> >>>> On Sat, Mar 5, 2016 at 10:27 AM, Eric Christoffersen <[email protected]> >>>> wrote: >>>> Woke this am mind ready to disassemble and test. And the machine is now at >>>> temp and seems to be working fine. >>>> >>>> So maybe... ordering the part... fixed the problem??? >>>> >>>> Well, at least I'll have the part when it does conk out. >>>> >>>> -- >>>> You received this message because you are subscribed to the Google Groups >>>> "Brewtus" group. >>>> To unsubscribe from this group and stop receiving emails from it, send an >>>> email to [email protected]. >>>> To post to this group, send email to [email protected]. >>>> Visit this group at https://groups.google.com/group/brewtus. >>>> For more options, visit https://groups.google.com/d/optout. >>> >>> -- >>> You received this message because you are subscribed to the Google Groups >>> "Brewtus" group. >>> To unsubscribe from this group and stop receiving emails from it, send an >>> email to [email protected]. >>> To post to this group, send email to [email protected]. >>> Visit this group at https://groups.google.com/group/brewtus. >>> For more options, visit https://groups.google.com/d/optout. > > -- > You received this message because you are subscribed to the Google Groups > "Brewtus" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To post to this group, send email to [email protected]. > Visit this group at https://groups.google.com/group/brewtus. > For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Brewtus" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To post to this group, send email to [email protected]. Visit this group at https://groups.google.com/group/brewtus. For more options, visit https://groups.google.com/d/optout.
