In as much as one only has 1 second minimum resolution, I'd say that is
quite normal. No,. the ALC/RF should not occur at the same time as the
TX LED is illuminated.
In order to correctly determine accurate timing values, one needs to use
a triggered dual trace scope to see exactly when things occur. In my
life, one second one way or the other makes absolutely no difference.
73
Bob, K4TAX
On 2/23/2018 1:16 PM, James Bennett wrote:
Made changes to my “radio” tab as suggested below and I see some improvement,
and wondering if this is what I should expect: At the “zero” time mark, the rig
red TX light comes on and at the +1 second mark, RF /ALC is happening. Expected
behavior? or should the RF/ALC start at the same time as the red TX light?
Both the K3 and KX3 are exhibiting the same response.
Jim / W6JHB
On Feb 23, 2018, at 10:32 AM, Walter Underwood <wun...@wunderwood.org> wrote:
Systems haven’t used two stop bits for decades. I’ve never set a system to two
stop bits and I was supporting a big UUCP node at Hewlett-Packard in the late
1980’s.
wunder
Walter Underwood
wun...@wunderwood.org <mailto:wun...@wunderwood.org>
http://observer.wunderwood.org/ <http://observer.wunderwood.org/> (my blog)
On Feb 23, 2018, at 9:58 AM, RIchard Williams via Elecraft <elecraft@mailman.qth.net
<mailto:elecraft@mailman.qth.net>> wrote:
When setting up radio settings in WSJT-X for the K3/K3S, I keep seeing different settings
for the number of stop bits (one and two) popping up on the reflector. Am not sure
where TWO stop bits is coming from??? On page 20 of the K3S manual (page 18 of the K3
manual), left hand column, Serial Port Setup, it states "Software should be set up
at the same rate: 8 data bits, no parity, 1 stop bit".
Have no idea why the Radio set window in WSJT-X defaults to TWO stop bits when
you select Elecraft K3/K3S. Initially, I did not catch this, and I was
encountering problems with my K3S remaining in transmit mode more often than
not after a transmission. Once I changed to ONE stop bit, my problem magically
went away.
What I have set up is:
Rig: Elecraft K3/K3S , Polling interval: 1sec
CAT control: COM 13 (which is a virtual com port set up with LP-Bridge with my
setup, your setting will be whatever com port are using).
Baud rate: 38,400
Data Bits, Stop Bits, and Handshake: 8, none, 1.
PTT method: CAT
Mode: Data/Pkt
Split Operation: Rig
DIck, K8ZTT
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to wun...@wunderwood.org <mailto:wun...@wunderwood.org>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
<http://mailman.qth.net/mailman/listinfo/elecraft>
Help: http://mailman.qth.net/mmfaq.htm <http://mailman.qth.net/mmfaq.htm>
Post: mailto:Elecraft@mailman.qth.net <mailto:Elecraft@mailman.qth.net>
This list hosted by: http://www.qsl.net <http://www.qsl.net/>
Please help support this email list: http://www.qsl.net/donate.html
<http://www.qsl.net/donate.html>
Message delivered to w6...@me.com <mailto:w6...@me.com>
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to rmcg...@blomand.net
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com
