The board originated in 99SE SP6. Rusty Land
----- Original Message ----- From: "Larryregnier" <[EMAIL PROTECTED]> To: "Protel EDA Forum" <[EMAIL PROTECTED]> Sent: Tuesday, October 15, 2002 9:37 AM Subject: Re: [PEDA] Keepout Fills Not Working After Movement 99SE > Rusty, > > Was this board originally a Protel 98 file? I have seen problems like this > after importing older versions into P99SE. > > Larry Regnier > High Density Design Inc > > ----- Original Message ----- > From: "Rusty Land" <[EMAIL PROTECTED]> > To: "Protel EDA Forum" <[EMAIL PROTECTED]> > Sent: Tuesday, October 15, 2002 9:27 AM > Subject: Re: [PEDA] Keepout Fills Not Working After Movement 99SE > > > > All the fills started out as "No Net", the fills that would not work > > took on the GND net. There was no obvious reason like overlapping vias > that > > would explain why they did. I'll try the close-open DDB trick next time. > > > > Thanks, Rusty Land > > > > ----- Original Message ----- > > From: "Brad Velander" <[EMAIL PROTECTED]> > > To: "'Protel EDA Forum'" <[EMAIL PROTECTED]> > > Sent: Monday, October 14, 2002 2:21 PM > > Subject: Re: [PEDA] Keepout Fills Not Working After Movement 99SE > > > > > > > Rusty, > > > this sounds very similar to a bug that I have run across with > > > keepout lines. At some point, possibly when you moved the fill, did it > > take > > > on a net when it came in contact with a net? Now you have changed the > net > > > name back to no net? > > > Here is the suggestion. With your fills in place and set to no net, > > > save the PCB and close the DDB. Reopen tha DDB and your fills should > > > function correctly again. This has something to do with the no net being > > set > > > after it was previously another net name. Saving and closing the file > > seems > > > to always correct it. > > > > > > Sincerely, > > > Brad Velander. > > > > > > Lead PCB Designer > > > Norsat International Inc. > > > Microwave Products > > > Tel (604) 292-9089 (direct line) > > > Fax (604) 292-9010 > > > email: [EMAIL PROTECTED] > > > http://www.norsat.com > > > Norsat's Microwave Products Division has now achieved ISO 9001:2000 > > > certification > > > > > > > > > > > > > -----Original Message----- > > > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] > > > > Sent: Monday, October 14, 2002 9:49 AM > > > > To: [EMAIL PROTECTED] > > > > Subject: [PEDA] Keepout Fills Not Working After Movement 99SE > > > > > > > > > > > > I have a board with 9 Keepout areas meant to keep out a > > > > copper plane pour on the top side. The first time the copper > > > > is poured the areas are kept copper free. But after selecting > > > > the fills and moving them aside when they are brought back > > > > for another pour two of the fill areas will not keep the > > > > copper out. These two areas were then redefined and work well > > > > but then two other areas would not keep the copper out on the > > > > next pour. > > > > I have seen this occur on a previous board. Why are these > > > > Keepout areas made ineffective by manipulation? Their net > > > > associations are all set to "No Net". > > > > > > > > Rusty Land > > > > > > > > > > > * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * To post a message: mailto:[EMAIL PROTECTED] * * To leave this list visit: * http://www.techservinc.com/protelusers/leave.html * * Contact the list manager: * mailto:[EMAIL PROTECTED] * * Forum Guidelines Rules: * http://www.techservinc.com/protelusers/forumrules.html * * Browse or Search previous postings: * http://www.mail-archive.com/proteledaforum@techservinc.com * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *