[Elecraft] KX2.KX3 Serial Port Extender

[Bill Conkling]

I have just put finishing touches on a Serial Port Expander for use with the 
KX3/KX2 series of transceivers. The device will plug into a regular or USB 
serial adapter (DE-9M) like the standard KUSB from Elecraft. 

I have posted a PDF document on my web site at http://nr4c.net/projects 
. 

I use SMD resistors and transistors to switch the DTR and RTS lines for CW and 
PTT. It also has the RXD & TXD signals use for cat control. It makes the KX 
transceivers look like a K3 to your logging software such as DXLabs and n1mm.  

The circuit board may be ordered from Oshpark.com  for 
$3.40 for 3 boards so interest a friend or two. There. Is a link in the doc for 
this service. 

I have included links to Mouser.com  for the transistors 
and resistors as well. They are very inexpensive but the shipping will get you 
if you don't order some other stuff. 

You can email me if you have any questions. 

BTW:  I have a limited supply of the transistors and resistors avail for $2.00 
for 3 each (in case you lose one) if you supply a SASE and 2 bucks. Email first 
as these are first come first served. No, I don't have any circuit boards at 
this time. 

Sent from my shack
...nr4c. bill

nr4c at iCloud dot com
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KPA500 power output starts out low, then goes up

[Bill Conkling]

just did that.  no help.

…bill
> On Nov 14, 2016, at 8:22 PM, ab2tc <ab...@arrl.net> wrote:
> 
> Hi,
> 
> How about following Vic, 4X6GP's advice and test the K3 without the KPA500
> in circuit? Your symptoms are exactly as if the K3 TX calibration is badly
> out of wack as he suggests. The fact that a band change makes it worse is a
> dead give-away. A band change makes the K3's ALC algorithm reset itself to
> defaults and these defaults are set by the TX gain calibration. Your
> situation seems a bit extreme, though, with only 20% initial power so there
> may be other problems. But please test this out without the KPA500 in
> circuit. And surely eliminate antenna problems by testing into a dummy load.
> 
> AB2TC - Knut
> 
> 
> 
> 
> Bill Conkling wrote
>> That hasn’t helped my KPA500.  I notice it particularly after a band
>> change.
>> 
>> …bill nr4c
>> 
>> 
>>> On Nov 13, 2016, at 10:58 PM, Vic Rosenthal 4X6GP 
> 
>> k2vco.vic@
> 
>>  wrote:
>>> 
>>> Hi Barthold,
>>> 
>>> Maybe the K3S output is ramping up slowly. Do you notice this with the
>>> KPA500 off? Running the TX Gain Calibration in the K3 Utility might help
>>> in that case.
>>> 
>>> 73,
>>> Vic, 4X6GP
>>> Rehovot, Israel
>>> Formerly K2VCO
>>> http://www.qsl.net/k2vco/
>>> 
>>> On 14 Nov 2016 00:51, Barthold Lichtenbelt via Elecraft wrote:
>>>> Hi All,
>>>> 
>>>> 
>>>> 
>>>> Maybe you can help with something that is baffling me. My KPA500 doesn't
>>>> go
>>>> to full output until I have spoken my callsign (when trying to get
>>>> through a
>>>> pileup) a few times. It starts off with 100 or so watts, and after a few
>>>> iterations rises to the full 500W output. I see this both on the KPA500
>>>> LED
>>>> bar, as well as on the P3 PEP output monitored by P3TXMON.  My full
>>>> setup is
>>>> K3S+KPA500+KAT500+P3+P3TXMON. All devices run the latest released
>>>> firmware.
>>>> 
>>>> 
>>>> 
>>>> Any thoughts much appreciated!
>>>> 
>>>> 
>>>> 
>>>> Barthold
>>>> 
>>>> AD0RM
>>> __
>>> Elecraft mailing list
>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft 
>>> <http://mailman.qth.net/mailman/listinfo/elecraft>
>>> Help: http://mailman.qth.net/mmfaq.htm <http://mailman.qth.net/mmfaq.htm>
>>> Post: mailto:
> 
>> Elecraft@.qth
> 
>>> 
>>> This list hosted by: http://www.qsl.net <http://www.qsl.net/>
>>> Please help support this email list: http://www.qsl.net/donate.html 
>>> <http://www.qsl.net/donate.html>
>>> Message delivered to 
> 
>> nr4c@
> 
>> 
>> __
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft 
>> <http://mailman.qth.net/mailman/listinfo/elecraft>
>> Help: http://mailman.qth.net/mmfaq.htm <http://mailman.qth.net/mmfaq.htm>
>> Post: mailto:
> 
>> Elecraft@.qth
> 
>> 
>> This list hosted by: http://www.qsl.net <http://www.qsl.net/>
>> Please help support this email list: http://www.qsl.net/donate.html 
>> <http://www.qsl.net/donate.html>
>> Message delivered to 
> 
>> lists+1215531472858-365791@.nabble
> 
> 
> 
> 
> 
> --
> View this message in context: 
> http://elecraft.365791.n2.nabble.com/KPA500-power-output-starts-out-low-then-goes-up-tp7623993p7624027.html
>  
> <http://elecraft.365791.n2.nabble.com/KPA500-power-output-starts-out-low-then-goes-up-tp7623993p7624027.html>
> Sent from the Elecraft mailing list archive at Nabble.com 
> <http://nabble.com/>.
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3 - AFSK

[Bill Conkling]

Check software.  I have noted my software switches sub-modes when making 
changes.  It has to do with mode selection and mapping softwre modes tot he 
radio mode/sub-mode.

bill nr4c

> On Nov 13, 2016, at 11:40 PM, W0MU Mike Fatchett  wrote:
> 
> It doesn't solve you issue but the K3 is really good with FSK, ie clean.
> 
> RF?  have you put ferrites on the cables with a number of turns? Does it 
> happen with 5 watts, 50 watts 100 or 1000 watts?
> 
> 
> 
> On 11/13/2016 8:47 PM, Robie Elms wrote:
>> All,
>> 
>> I have very limited experience with a K3 and I am helping a fellow club
>> member get up and running on RTTY with his K3.  Here is the setup:
>> 
>> 1. We are using MMTTY in the AFSK mode
>> 
>> 2. line in/out on the transceiver connected to the computer sound card mic
>> and speaker input/output
>> 
>> 3. PTT is via command the radio control port.
>> 
>> 
>> The problem we are having is intermittent transmission of data.  At times
>> the set up works properly and then later when transmitting the K3 sends
>> only a steady carrier.  It appears that the computer is outputting audio
>> tones to the K3 when this situation occurs.  What are the potential causes
>> of this problem.  Any suggestions will be appreciated.
>> 
>> Robie - AJ4F
>> __
>> Elecraft mailing list
>> Home: http://mailman.qth.net/mailman/listinfo/elecraft
>> Help: http://mailman.qth.net/mmfaq.htm
>> Post: mailto:Elecraft@mailman.qth.net
>> 
>> This list hosted by: http://www.qsl.net
>> Please help support this email list: http://www.qsl.net/donate.html
>> Message delivered to w...@w0mu.com 
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft 
> 
> Help: http://mailman.qth.net/mmfaq.htm 
> Post: mailto:Elecraft@mailman.qth.net 
> 
> This list hosted by: http://www.qsl.net 
> Please help support this email list: http://www.qsl.net/donate.html 
> 
> Message delivered to n...@widomaker.com 
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KPA500 power output starts out low, then goes up

[Bill Conkling]

That hasn’t helped my KPA500.  I notice it particularly after a band change.

…bill nr4c


> On Nov 13, 2016, at 10:58 PM, Vic Rosenthal 4X6GP  wrote:
> 
> Hi Barthold,
> 
> Maybe the K3S output is ramping up slowly. Do you notice this with the KPA500 
> off? Running the TX Gain Calibration in the K3 Utility might help in that 
> case.
> 
> 73,
> Vic, 4X6GP
> Rehovot, Israel
> Formerly K2VCO
> http://www.qsl.net/k2vco/
> 
> On 14 Nov 2016 00:51, Barthold Lichtenbelt via Elecraft wrote:
>> Hi All,
>> 
>> 
>> 
>> Maybe you can help with something that is baffling me. My KPA500 doesn't go
>> to full output until I have spoken my callsign (when trying to get through a
>> pileup) a few times. It starts off with 100 or so watts, and after a few
>> iterations rises to the full 500W output. I see this both on the KPA500 LED
>> bar, as well as on the P3 PEP output monitored by P3TXMON.  My full setup is
>> K3S+KPA500+KAT500+P3+P3TXMON. All devices run the latest released firmware.
>> 
>> 
>> 
>> Any thoughts much appreciated!
>> 
>> 
>> 
>> Barthold
>> 
>> AD0RM
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Windows Emulator

[Bill Conkling]

I used BOOTCAMP to set aside a portion of my hard drive for Windows and 
installed Win8.1 (now upgraded to 10).  Now I can boot into either OS and use 
it.  Works great.  MAC hardware runs windows better than my old HP laptop.

I also purchased VMWare Fusion and used the Bootcamp partition as my virrtual 
machine,

Now I have the best of both worlds,

…bill nr4c



> On Oct 12, 2016, at 12:47 PM, Richard Fjeld  wrote:
> 
> Just a suggestion;
> 
> I don't know what all this would cost you, but $350 can buy a very 
> decent Windows laptop.  I bought a Lenovo with an i5 cpu and 8 Gb of ram 
> plus an optical drive and more,  from the Microsoft store for that 
> amount. You have to watch for good offers.
> 
> Dick, n0ce
> 
> 
> On 10/12/2016 11:20 AM, Dauer, Edward wrote:
>> I give up.
>> 
>> I have tried to be faithful to my decision of a few years ago, to swear off 
>> Windows and work exclusively with Mac OS.  But there’s just too much that I 
>> want that isn’t available in OS – Spectrogram, for example, and any number 
>> of logging programs I’d like to try.
>> 
>> It’s not time yet for a new computer, and I want to keep all of my Mac apps 
>> and files intact; so the question is what sort of Windows emulator would be 
>> best to install in the Mac computers.  I use a 4-year old MacBook Air as a 
>> laptop and an even older iMac on my desk.  Both now run OS X Yosemite and I 
>> will not upgrade to Sierra, in case that matters.
>> 
>> Advice?  Thanks in advance,
>> 
>> Ted, KN1CBR
>> 
>> __
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 KXUSB Cable

[Bill Conkling]

The cable pictured has a TRRS 3.5 mm plug, not the TRS as on the real thing.

id skip it  





> On Aug 28, 2016, at 5:28 PM, Charles  wrote:
> 
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3 Operating Tip: Using TX TEST to adjust speech controls and ALC level

[Bill Conkling]

If you're referencing the RED TX lED, it only lights up when actually 
transmitting, not in TEST mode.

…billc nr4c



> On Jul 31, 2016, at 3:33 PM, MaverickNH  wrote:
> 
> Hey Don - that was the missing setting indeed! The K3s isn't your Father's
> transceiver, for sure. In fact, my FT-897D is sitting on the floor waiting
> to be re-purposed.
> 
> The red LED doesn't blink in TX TEST still...I saw some controversy about
> that on the forum, so maybe the blinking is disabled by default, if not
> permanently.
> 
> 73s, BRET/KC1CJN
> 
> 
> 
> --
> View this message in context: 
> http://elecraft.365791.n2.nabble.com/K3-Operating-Tip-Using-TX-TEST-to-adjust-speech-controls-and-ALC-level-tp5289738p7620968.html
> Sent from the Elecraft mailing list archive at Nabble.com.
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Power has disappeared

[Bill Conkling]

Couple questions:

1) What radio, K3 or K3S, or K2/100?

2) which antenna, 1 or 2?

3) You said you turned the “temps down to a more reasonable 23C…”  I don’t 
recall a temp setting, only a REF to current room temperature calibration step.

4) What is the voltage shown on the front panel display?

…billc nr4c



> On Jul 27, 2016, at 11:52 AM, Richard Fjeld  wrote:
> 
> I apologize for this, but being it's a new rig it has to be said; could there 
> be any confusion in the antenna jack selection?
> I haven't followed how it is equipped.
> 
> Dick, n0ce
> 
> 
> On 7/26/2016 7:48 PM, Chris Kimball wrote:
>> I'm a new owner and all worked fine.  After an absence of a few days I came
>> back to no power out, or , at least, very little.
>> 
>> Rig is the 100W version with ATU working into a dummy load.  In CW mode
>> adjusting the power level to 70W produces only a one segment power out.
>> Running the ATU produces a 5W indication, the usual searching rumbling, but
>> no resultant SWR. The Test mode is NOT in operation.
>> 
>> I have restored to the last working config via K3 Utility, but suspect I
>> must have "hit" something to limit the power.  The FP and AMP temps were too
>> high (35C) when the problem was noticed. I set them down to a more
>> reasonable 23C without effect. Input voltage is 12.8V.
>> 
>> Probably something trivial, but suggestions would be appreciated.
>> 
>> Chris
>> NQ8Z
>> 
>> 
>> 
>> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX3 Antenna Tuner Settings

[Bill Conkling]

I’m sorry, but I understood that Jay is looking to interrogate the ATU in the 
KX3 for the settings that the tuner made to match the antenna,

And unfortunately this feature is only available on the K3(s) KAT3(A).  i 
thought it was also available the KX3 ATU.

maybe in a futeure FW release.

…bc nr4c




> On Jul 25, 2016, at 1:06 PM, Jay Sissom  wrote:
> 
> Is there any way to determine the settings that the antenna tuner
> determined were necessary for an antenna?  I would like to be able to move
> my antenna around and determine which one is a better match for the
> frequency being used.  It would be awesome to do this with just the radio
> instead of needing an external device.
> 
> Thanks & 73
> Jay
> W9IUF
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3 (not S) Antenna tuner strangeness

[Bill Conkling]

Try a “slightly different tap position” and see what happens.  Your words, not 
mine.

…bill  nr4c



> On Jul 22, 2016, at 12:19 PM, brian  wrote:
> 
> Guys,
> 
> I've run into something on 80M trying to use the internal antenna tuner.
> It fails to tune to a low SWR.
> 
> My recollection is that the tuner worked fine on the same antenna before. 
> "Worked before" may have been with a slightly different tap position.
> 
> Antenna is an MFJ 1/8 Wave vertical with loading coil and 4:1 "Guanella" 
> balun at the antenna base.
> 
> With the current coil tap an RF analyst antenna analyzer shows the following:
> 
> 3.55 MHz SWR=2.0  Z=35 ohms
> 3.6  SWR=2.7  Z=36 ohms
> 
> The K3 in the tune position (tuner out) shows SWR's of 1.7 and 2.4 
> respectively.
> 
> The antenna tuner finds a match for a 50 ohm dummy load OK.  Using those 
> settings as a starting point, we attempted to match the antenna.
> 
> The best it can do is bring the 1.7 SWR down to 1.4.  The 2.0 SWR can brought 
> down to 1.7 at best.
> 
> Other bands work OK.
> 
> Any thoughts?
> 
> 73 de Brian/K3KO
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3 error message

[Bill Conkling]

Aren’t you supposed to have the filters in the sub receiver in the same slot as 
the main receiver?  I’m not saying that all filters in the main have to be in 
the sub, but any that are the same, shouldn’t they be in the sane slot?

…bc nr4c



> On Jul 20, 2016, at 8:15 PM, Don Wilhelm  wrote:
> 
> Mike,
> 
> Since you moved the filters in the KRX3, you may want to go into the CONFIG 
> menu and tell it which filters for the KRX3 are installed and in which slots.
> 
> 73,
> Do W3FPR
> 
> On 7/19/2016 8:06 PM, Mike Murray wrote:
>> After removing one filter from my subRx and moving the remaining filter
>> (2.8) to position #1, I'm now getting and ERR BP3 on start up.  Before I
>> open everything up again and remove the KRX3, SUBIN and SUBOUT boards and
>> reset everything as detailed in the manual, is there anything else I should
>> be doing to troubleshoot?  It's obviously a problem with the SubRx, but I
>> thought I was being ultra cautious during the disassembly/assembly process,
>> including use of static protection precautions.
>> 
>> 
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] [K3] Looking for feedback on K3DVR

[Bill Conkling]

I use my K3DVR a lot.  It is useful for contests as well as day-to-day DXing,  
Who enjoys calling “CQ CQ” for hours or, repeating your call when trying to 
break tha pileup on K1N, etc?

Get it.

…bill  nr4c


> On Jul 20, 2016, at 6:29 PM, Ian - Ham  wrote:
> 
> All,
> 
> 
> 
> After competing somewhat competitively in the Georgia QSO Party the last few
> years, and participating as one of the hunted 13 Colonies special event
> stations in Georgia for the last couple of years, I find myself ready to add
> a voice keyer to my shack set up. To that end, and in order to minimize desk
> clutter, I'm looking at the KDVR3 for my K3 s/n 281 as a possible solution.
> However, I've heard anecdotal evidence from hams in my area who have the
> KDVR3 that it probably isn't the best solution for a voice keyer because it
> has long (>1 sec) delays before both beginning transmission of the recorded
> message and dropping transmit at the end of the message. Before I drop $150
> on a component that might not be the solution I'm looking for, I would love
> to get others' opinions and feedback on their experiences using the KDVR3 as
> a voice keyer.
> 
> 
> 
> Thanks and 73,
> 
> 
> 
> --Ian
> 
> Ian Kahn, KM4IK
> Roswell, GA  EM74ua
> km4ik@gmail.com  
> 
> 10-10 #74624, North Georgia Chapter #2038
> 
> PODXS 070 #1962
> K3# 281, P3 #688, KAT500 #860, KPA500 #1468
> 
> 
> 
> 
> 
> ---
> This email has been checked for viruses by Avast antivirus software.
> https://www.avast.com/antivirus
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] How difficult is it to install the FM filter ofr K3 with ...

[Bill Conkling]

Well, the FM filter for the main receiver is mounted on the main RF board.  So 
the 2Meter module must come out, and the sub-receiver, and of course the top 
and front bottom panel,  I also think it is easier to re-install the 
sub-receiver if you remove the left side panel (with handle).

…bill nr4c



> On Jul 19, 2016, at 3:50 PM, mike  wrote:
> 
> I have a K3 with the 2 meter module and second receiver installed. I recently
> acquired a FM filter and am wondering how difficult it would be to install
> it. Mostly I guess I am looking for an idea on what steps I need to perform
> and in what order. I installed the second receiver some time ago after
> installing the 2 meter module and remember it was quite involved. Before I
> attempt to add the FM filter I want to make sure I am up to the challenge.
> Any suggestions would be greatly appreciated.  73  ..mike  AI6II
> 
> 
> 
> --
> View this message in context: 
> http://elecraft.365791.n2.nabble.com/How-difficult-is-it-to-install-the-FM-filter-ofr-K3-with-tp7620404.html
> Sent from the Elecraft mailing list archive at Nabble.com.
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Buy a K3S?

[Bill Conkling]

AKA “Buy nice, not twice”

…bc  nr4c



> On Jul 19, 2016, at 4:13 PM, Dauer, Edward  wrote:
> 
> Agree fully with the suggestions.
> 
> As to equipment, I once saw a sign in a high-end telescope shop:  “Buy the 
> best first and cry only once.”
> 
> Ted, KN1CBR
> 
> --
> 
> Message: 30
> Date: Tue, 19 Jul 2016 14:46:19 -0400
> From: "Jerry Moore" 
> To: "'Reuben Popp'" ,  "'Elecraft Reflector
>   Reflector'" 
> Subject: Re: [Elecraft] Help sell me on the K3S
> Message-ID: <002201d1e1ed$d7ebf940$87c3ebc0$@carolinaheli.com>
> Content-Type: text/plain; charset="us-ascii"
> 
> I will throw my view into the mix. 
> 
> As a new Ham operator you have no idea what you want to do in the hobby
> other than EVERYTHING!!!
> In addition to wanting to do everything we're also most often budget limited
> to some extent. 
> 
> Challenge: Weigh the desire to do everything with  the most cost effective
> way to get started until we know what we actually enjoy.
> 
> Suggestions: 
> 1. Find a mentor (in our hobby they are called Elmers) to help you along,
> get you on the air, and help you get experience to find out WHAT you ENJOY
> doing in the hobby. 
> 2. Meet with as many hams who do different things in the hobby as you can
> and ask them to show you that part of the hobbyexample: HF, UHF/VHF,
> EME, DX, Contesting, Different modesetc.. 
> 
> Once you know what you ENJOY in the hobby you can best invest in the
> resources to engage. 
> 
> 
> My world view of ham radio gear specific to Elecraft:
> 
> Most Gear Advantage (generalizations): cheaper, simple to use/operate
> (appliance operator ), may have firmware updates.
> Most Gear Disadvantage (generalizations): limited to the manf. Design limits
> and locked to model, firmware updates generally limited to correcting bugs
> and not generally to add features/functionality.
> 
> 
> Elecraft Disadvantages (my opinion and generalizations): High entry price,
> operator MUST learn to use the gear, configurations can be complex and are
> generally open ended
> Elecraft Advantages (my opinion and generalizations): Gear is highly
> adaptable to conditions and configuration based on operator demands a the
> time, hardware and software upgrades (both hardware and software upgrades
> have traditionally been for new features/functionality in addition to bug
> fixes).
> 
> 
> 
> 
> Summary: I would have been happy with a less expensive radio, however, I
> would have been frustrated at the limitations. I purchased my Elecraft K3S
> specifically to avoid the frustrations I've experienced with other gear in
> the past. To date I've not been let down (although the cost of the options
> has prevented me from doing the add-ons that would be nice to have..e.g. sub
> rx, P3..etc). 
> 
> Jerry Moore
> AE4PB
> 
> 
> 
> 
> --
> 
> Subject: Digest Footer
> 
> ___
> Elecraft mailing list
> Post to: Elecraft@mailman.qth.net
> http://mailman.qth.net/mailman/listinfo/elecraft
> You must be a subscriber to post.
> Elecraft web page: http://www.elecraft.com
> 
> --
> 
> End of Elecraft Digest, Vol 147, Issue 35
> *
> 
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 and N1MM F-Keys

[Bill Conkling]

From my own experience, KY commands work but are clumsy, and there is a l limit 
to how many characters can be sent with one command,  The simple switching 
circuit is quite easy to do and works extremely well,  

All it takes is a 2N transistor with base connected to the proper pin (4 or 
7) thru a 1.2K (1k -1.5K) Ohm resistor,  The collector goes to the plug shield 
and the emitter goes to the tip of the plug.

Plug this into the standard KUSB or standard serial cable.

…bc nr4c

> On Jul 7, 2016, at 10:26 AM, K5WA  wrote:
> 
> Fred,
> 
> One tap of the paddle stops transmission when using KY so you really don't
> need ESC.  
> 
> Bob K5WA
> 
> From: Cady, Fred [mailto:fc...@montana.edu] 
> Sent: Thursday, July 7, 2016 7:15 AM
> To: K5WA; elecraft@mailman.qth.net
> Subject: Re: [Elecraft] KX2 and N1MM F-Keys
> 
> When using KY commands in N1MM does hitting escape stop the transmission?
> If no, that would be a disadvantage to me.  A couple of transistor switches,
> actually just one because you don't need PTT usually, is pretty easy to
> build.  There are lots of examples of circuits out there.
> Cheers,
> Fred KE7X
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX2 and N1MM F-Keys

[Bill Conkling]

You can build a pair of simple transistor witches into a DE-9 shell and add 
cables for TX, RX, DTR, and RTS with the proper plugs and it will “look” like a 
K3 to your software.

…bill nr4c

> On Jul 6, 2016, at 11:01 PM, K5WA  wrote:
> 
> I forgot who I responded to about setting up a KX2 with N1MM and a single
> USB cable recently but I need to revise my answer.  The answer I gave
> assumed the DTR/RTS lines were assignable to CW or PTT like the K3 does
> however since the KX2 (like the KX3, I believe) doesn't have DTR/RTS lines
> assignable in the rig, you need to send ASCII streams to the KX2 in order to
> use F-keys within N1MM.  I just got my new KX2 today (love it!!) and started
> playing with it when I discovered there weren't any DTR/RTS signals to use.
> A way to send ASCII streams via F-keys with N1MM (and probably other contest
> software F keys) is to follow the examples below and write whatever messages
> you want once you've gotten the basic {CATA1ASC KY   ;} piece in place.
> These are a few messages I started playing with so you can see some
> possibilities but the permutations are endless to get exactly what you want.
> The only downside I found was that I can't use N1MM's "autosend" feature
> (which is meant to save you from having to hit the enter key every time).
> I like autosend set at 2 characters past the number but when I try to use
> it, the calls over 2 characters past the number get mangled when being sent.
> I'm guessing that the ASCII string is interrupted once the rig switches to
> transmit and therefore the call sending is mangled.  Maybe there is a
> workaround that I have not discovered yet but I doubt many folks are going
> to be doing lots of contesting with a KX2 anyway so it really isn't much of
> a downside.  I can imagine I'll be on a business trip or a vacation trip and
> want to toss out a few contacts to the serious contesters using my
> mini-notebook and KX2 so hitting enter won't be too big a hassle.  ;-)
> 
> Hope this helps someone but I have not extensively checked each one of the
> entries below so play with yours to get it right if I made a mistake.  Most
> should be right though as I played around in a simulated contest to get
> these working.
> 
> Bob K5WA
> 
> 
> F1 CQ,{CATA1ASC KY k5wa k5wa test;}
> F2 EXCH,{CATA1ASC KY ! {EXCH};}
> F3 TU,{CATA1ASC KY tu * test {CLEARRIT};}
> F4 His Call,{CATA1ASC KY!;}
> F5 K5WA,{CATA1ASC KY *;}
> F6 AGN,{CATA1ASC KY agn?;}
> F7 ?,{CATA1ASC KY ?;}
> F8 ?,{CATA1ASC KY ?;}
> F9 S&,{CATA1ASC KY{S};}
> F10 Call & Exc,{CATA1ASC KY{!} {EXCH};}
> F11 CQ (long),{CATA1ASC KY CQ CQ TEST K5WA K5WA;}
> F12 Wipe,{CATA1ASC KY{WIPE};}
> #
> ###
> #   S Messages 
> ###
> F1 Qrl?,{CATA1ASC KY QRL? K5WA;} 
> F2 Exch,{CATA1ASC KY 5nn {EXCH};}
> F3 Tu,{CATA1ASC KY{!} tu{LOG};}
> F4 His Call,{CATA1ASC KY{!};}
> F5 K5WA,{CATA1ASC KY K5WA;}
> F6 AGN,{CATA1ASC KY ?;}
> F7 ?,{CATA1ASC KY ?;}
> F8 ?,{CATA1ASC KY ?;}
> F9 RUN,{CATA1ASC KY {RUN};}
> F10 Call & Exc,{CATA1ASC KY{!} {EXCH};}
> F11 
> F12 Wipe,{CATA1ASC KY{WIPE};}
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Field Day Report

[Bill Conkling]

At K4RC, I made 8 on 80 m PSK31 and about 21 on RTTY on 20 and 40 M.  I only 
worked about an hour or so at times when the Phone station was between 
operators.

…bc  mr4c

> On Jul 1, 2016, at 6:22 PM, Bill Frantz  wrote:
> 
> Out of curiosity, what digital modes did people use to make contacts at Field 
> Day. Our operation got good results from PSK31 and RTTY, but did not try 
> other modes.
> 
> 73 Bill AE6JV
> 
> ---
> Bill Frantz| "The only thing we have to   | Periwinkle
> (408)356-8506  | fear is fear itself." - FDR  | 16345 Englewood Ave
> www.pwpconsult.com | Inaugural address, 3/4/1933  | Los Gatos, CA 95032
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX3 IMD vs DC input, using built-in 2 TONE

[Bill Conkling]

You do realize you can adjust the level one of the tones with the mic gain 
control, don’t you?

..bc nr4c

> On Jun 12, 2016, at 6:11 PM, Erik Basilier  wrote:
> 
> Of course, I don't mean that the nature of the  2 tones affect the IMD
> characteristics of the hardware. Rather, what I meant was: "if one measures
> IMD with a standard 1:1 amplitude ratio, and then measures again with a
> non-standard 2:3 ratio, how much would the IMD suppression number change,
> and in what direction?" I imagine that the answer could be found either by
> using independently adjustable external audio tone generators, or with a
> math package.
> 
> -Original Message-
> From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Erik
> Basilier
> Sent: Sunday, June 12, 2016 2:56 PM
> To: Elecraft@mailman.qth.net
> Subject: Re: [Elecraft] KX3 IMD vs DC input, using built-in 2 TONE
> 
> One more question:
> 
> Assuming that the 2 tones are about 2:3 in amplitude ratio, can anyone say
> how that would be expected to affect the 3rd order IMD figures?
> 
> 
> 
> From: Erik Basilier [mailto:ebasil...@cox.net]
> Sent: Sunday, June 12, 2016 2:53 PM
> To: 'Elecraft@mailman.qth.net' 
> Subject: KX3 IMD vs DC input, using built-in 2 TONE
> 
> 
> 
> I am testing my KX3 / KXPA100 combo, looking at TX IMD and power output
> depending on the DC power supply characteristics. I am experimenting with a
> N8XJK Boost Regulator (40A max) as well as an Astron linear supply adjusted
> down to low voltage, simulating a run-down battery. 
> 
> 
> 
> To judge IMD I use the built-in 2 TONE, mix down sampled output to audio,
> and feed into Spectrum Lab.
> 
> 
> 
> When I look at the envelope, its smallest amplitude is about 1/3 of peak.
> This suggests that the 2 tones are not of equal amplitude. Has anyone else
> seen this? I downloaded the laterst firmware about a week ago.
> 
> 
> 
> Thanks,
> 
> Erik K7TV
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html Message
> delivered to ebasil...@cox.net
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K-Pod Info

[Bill Conkling]

If you read the data sheet on the website, it says 
"A utility jack beneath the radio’s front panel acts as the K-Pod’s data 
interface. The unit can be powered from the radio’s rear 12-V accessory output, 
the pod’s own USB port, or any 8-15 V, 50-mA DC power source.*”

…bill nr4c
 




> On Jun 9, 2016, at 1:31 PM, Francisco Siso Hennessey HK3W 
>  wrote:
> 
> Will be great to know how to connect K-Pod before purchase it. I have K3S +
> KAT500 + KPA500 + P3 + MicrohamII + SP3 x 2 and I don't see where to
> connnect it.
> 
> Any advice will be aprreciated
> 
> Regards,
> Siso HK3W
> _
> 
> *Francisco "Siso" Hennessey - H K 3 W ---*
> 
> *ARRL DXCC Card Checker*
> 
> *DXCC HR - DXCC CW - DXCC RTTY -DXCC SSB - 8BDXCC -** | * Skype: siso-hk3w |
> *Twitter: **http://twitter.com/HK3W   *|
> 
> *Member of: **ARRL (LM) -  LoTW -*
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Krx3a

[Bill Conkling]

What is your antenna arrangement?  If you have ‘REC” antenna(s) you might go 
one way, if you only have one antenna, just use the Main antenna.

…bc  nr4c
> On Jun 4, 2016, at 3:23 PM, Doug  wrote:
> 
> Ok. I'm installing the rx in my k3.  But I'm not sure how to wire it for 
> connection to a antenna. It will be uses for split operation dxing. Any 
> suggestions will be appreciated   Wd8z. Doug
> 
> Sent from my iPhone
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Hooking 2 headsets to K3S

[Bill Conkling]

I just plug one into the rear jacks, usually also the mic of my CM500.  Then 
plug the phones of a second CM500 into the front phones jack (w/adapter).

For many of our club events we leave the CONFIG/Speaker+phone set to “YES”. so 
that onlookers may listen as well  But using phones for operator and logger 
allows some isolation from chatter of by-standers standing around.

…bill  nr4c


> On May 26, 2016, at 11:50 AM, Doug Kingston  wrote:
> 
> What is the recommended way to hook 2 headsets to a K3S?  Is a stereo "Y"
> cable sufficient?
> 
> -Doug-
> KD7DK
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Yamaha CM500 PTT Switch

[Bill Conkling]

find an old desk mic and remove the mic.

I am in the process of deigning and building a simple PTT switch that is 
basically the base of a desk mic without the mic.  When I get it finished, I 
will post it here for comment.  It will be a  3D printed box and some switches 
and a 1/8 plug for a cable.I made one from thin plywood using a couple of 
relay contacts back in 2008 and my club and I have used it ever since fopr 
thousands of contacts both indoors and out.

…bc  nr4c



> On Mar 2, 2016, at 4:57 PM, Don Wilhelm  wrote:
> 
> Steven,
> 
> The hard part is finding a handheld switch that you are comfortable with.  As 
> someone mentioned, if you have another microphone with a PTT switch, plug 
> that into the front panel and plug the CM500 into the rear.  When the rear 
> panel microphone is selected, the PTT button on the microphone will work (but 
> the mic will not).
> 
> The other alternative is to find a cable mounted switch that you are 
> comfortable with and solder an RCA Plug to the end of the cable - plug it 
> into the rear panel PTT jack.
> 
> 73,
> Don W3FPR
> 
> On 3/2/2016 3:16 PM, Steven Stuckey wrote:
>> Please read carefully. I am wanting to get a Yamaha CM500 and add a PTT
>> switch. Do not recommend a foot switch I am wheelchair bound and have no
>> way of using my feet. I am looking for a button PTT switch and not a
>> trigger switch. When I searched the internet the one I saw was "no longer
>> in production for new orders" due to health issues. I may consider building
>> my own. The Yamaha CM500 and PTT switch will be used with my K3S.
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Amp or tuner / Chicken or Egg

[Bill Conkling]

Check the K3S assembly manual.  If I remember correctly from my Original K3 
assembly, the manual paused to instruct you when it was time to install various 
options to allow you to install or skip steps if yu were not installing that 
option.



> On Feb 17, 2016, at 4:12 PM, Gary Smith  wrote:
> 
> Just got my factory assembled K3s/10 delivered. I need to install the 
> 100W amp and internal tuner. Seems like I'd want to install the amp 
> first. 
> 
> Yes?
> 
> Thanks & 73,
> 
> Gary
> KA1J
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3 - KIO3B setup

[Bill Conkling]

Well, first, I don’ recognize the CBLP3T cable.  Maybe you meant CBLP3Y? If so, 
I think yu would still need a DE-9 “Y” cable to connect at the P3 at which ever 
port you used before (TXCVR or PC).

Be sure to set CONFIG:RS-232 to USB and not 38400 as before.  And now your 
audio input/output is the new USB CODEC.  Have fun and let us know how it works.

…bc  nr4c




> On Jan 18, 2016, at 4:24 PM, N2TK, Tony  wrote:
> 
> I installed the KIO3B kit. I have it set up as the original KIO3 - K3- RS232
> to P3 to PC/SteppIR. Accessory plug with FSK interface and audio in and out
> cables to audio board. I use LP-Bridge. Everything is working fine as it was
> before the upgrade.
> 
> Now I want to take advantage of the features of the KIO3B kit.
> 
> 
> 
> I have the CBLP3T cable for the K3 to the P3. 
> 
> I will replace the RS232 with the USB to the PC.
> 
> I will remove the audio in and out cables. 
> 
> 
> 
> Is there anything special I need to do now that I will be using a USB port
> instead of the RS232? 
> 
> What about with LP-Bridge? Anything I need to do with it? 
> 
> Where is the best place to hook up the SteppiR now that I don't have an
> RS232 connecting to the PC?
> 
> 
> 
> Tnx for any feedback.
> 
> 73,
> 
> N2TK, Tony
> 
> 
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] [K3] CW Message Memories

[Bill Conkling]

You are correct that the KDVR3 is not needed for CW messages.  However, you 
must be in CW mode (or one of the two DATA sub-modes PSK-D or FSK-D) for these 
messages to work.  And, if you are set to SPLIT operation, VFO B must also be 
in CW mode.

They also work in TEST mode.  However, be careful, my K3S MODE button is more 
fussy than the button on my K3 and sometimes when trying to get the TEST mode, 
I press the  button not quite right and it goes to SSB/LSB so that when I press 
it again, now i’m in TEST mode, but in SSB instead of CW.

…bill  nr4c

> On Jan 18, 2016, at 3:16 PM, David Christ  wrote:
> 
> I have myself confused.  Is the KDVR3 required to use the CW message 
> memories? At first I thought it wasn’t but I used the K3 Utility to load some 
> messages into the CW memories.  Then I placed the K3 into test mode and CW 
> mode.  When I press any of the M1-M4 keys I get the message  “NO DVR” in the 
> VFO B area.  So is the KDVR3 required or am I doing something wrong.  Neither 
> the K3 manual or the Cady book have helped me understand this.  Neither says 
> the KDVR3 is needed and the KDVR3 manual only talks about voice recording 
> which implies it is not involved with CW message memories.
> 
> David K0LUM
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Strange behavior of P3

[Bill Conkling]

See below…..


> On Jan 15, 2016, at 3:26 PM, Martin  wrote:
> 
> 
> …….. if the mode of the main receiver is changed from any mode to TX DATA 
> (Submode
> DATA A). 
Noter, there is no Mode "TX DATA”.  The “TX” is an icon with an arrow pointing 
either down to it, or up to it indicating which VFO (A or B) is the transmit 
frequency.  It jujst happens that the MODE “DATA” is next to it.


…bill c nr4c
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3 SN89XX Audio Problem Help please

[Bill Conkling]

Bill,

The “phones” work all the time.  SPKR+PH only controls the speaker.  It allows 
me to operate at night without bothering the OWMBO (One who must……).

…billc nr4c



> On Jan 15, 2016, at 2:46 PM, Bill OMara via Elecraft 
>  wrote:
> 
> I have a new to me, Used K3 that looks to have a setting or audio problem I
> can't figure out.
> 
> 
> 
> The problem I'm having is the CONFIG setting for "SPKR+PH" is set for Yes
> and the audio is working the way I understand it to work (Both Speaker and
> headphone audio at the same time).
> 
> 
> 
> But when I change "SPKR+PH" to NO I only get Audio if the Headphones are
> plugged in, when I unplug the headsets NO audio comes out vis the internal
> speaker and the radio audio is gone.  If I then go to the CONFIG settings
> for for "SPKR+PH" and change it back to "yes" then the internal speaker then
> provides audio again.
> 
> 
> 
> What am I missing?
> 
> 
> 
> No second receiver is installed if this has any impact.
> 
> 
> 
> I own two other K3 radios and they do not act in this manner.
> 
> 
> 
> 
> 
> Thanks for any help
> 
> 
> 
> 73 Bill  W4RM
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KY Command

[Bill Conkling]

Yes, I had the same issue last weekend.  I rec’d help from several listers 
including Dick who showed me the proper syntax for n1mm.  Below is the function 
key file I used with n1mm.

#NEW VERSION, This Function Key File requires N1MM Logger V12.02.00 or newer 
#EDITS REQUIRED, before using this file-
#SPECIAL INSTRUCTIONS, -
#REM, non-ESM mode  logs the contact and clears the QSO Entry window
#REM, S F1 calls CQ and automatically places the program in RUN mode
#REM, Designed to work in either ESM or non-ESM mode
#REM, F2 F3 F4 F5 use "!" macro for his callsign
#REM, F2 F7 {SENTRST} defaults to 599 or allows manual entry of sig report
#REM, I have shown examples of using "*", "!" as well as {MYCALL}and
#REM, (CALL) for call signs.  
#REM, I use MMVARI for digital modes with n1mm because it will 
#REM, work with RTTY and PSK31.
#REM, Use DATA sub-mode FSK-D with this file.  The file also
#REM, will work with DATA sub-mode PSK-D as well as CW.
#REM, RUN MESSAGES, Run Messages begin here 
-
F1 Run CQ,{CATA1ASC KY ~CQ CQ RU {MYCALL} {MYCALL} CQ <04>;K30;}
F2 Run Exch,{CATA1ASC  599 VA VA <04>;K30;}
F3 Run TU,{CATA1ASC KY {CALL} TU {MYCALL} QRZ <04>;K30;}
F4 Run MyCall,{CATA1ASC KY {MYCALL} <04>;K30;}
F5 His Call,{CATA1ASC KY ! }
F6 -, -
F7 My Exch,{CATA1ASC KY {SENTRST} {EXCH}  {SENTRST} {EXCH} <04>;K30;;}
F8 Agn?, {CATA1ASC KY AGN? AGN ? <04>;K30;}
F9 Number?,{CATA1ASC KY NUMBER # <04>;K30;}
F10 State?,{CATA1ASC KY STATE/PROV ??? <04>;K30;}
F11 STOP, {CATA1ASC K31;SWT16;} 
F12 Wipe, {WIPE}
#S MESSAGES, Search and Pounce Messages begin here ---
F1 S& CQ,{CATA1ASC KY CQ RU * * CQ <04>;K30;}
F2 S& Exch,{CATA1ASC KY ! 599 VA 599 VA <04>;K30;}
F3 S& TU,{CATA1ASC KY TU * QRZ <04>;K30;}
F4 S& MyCall,{CATA1ASC KY NR4C * * <04>;K30;}
F5 His Call,{CATA1ASC KY ! <04>;K30;}
F6 -, -
F7 My Exch,{CATA1ASC KY 599 VA 599 VA <04>;K30;;}
F8 Agn?, {CATA1ASC KY AGN? AGN ? <04>;K30;}
F9 Number?,{CATA1ASC KY NUMBER # <04>;K30;}
F10 State?,{CATA1ASC KY STATE/PROV <04>;K30;}
F11 STOP, {CATA1ASC K31;SWT16;} 
F12 Wipe, {WIPE}

The "<04>;” is a ^D or ctrl-D which is an EOT (end of transmission) character 
from ‘days of olde’ i’m told. The brackets indicate HEX base.

I realize these are for n1mm, your software may be totally different.  Hope 
this helps, some.

…bill  nr4c

> On Jan 6, 2016, at 11:55 PM, Rich  wrote:
> 
> I am trying to use the KY command with Writelog for RTTY contesting.  I have 
> no problem setting up a Keyboard shortcut which then sends the data in the KY 
> command, however I cannot find a way to stop the K3 from transmitting after 
> the command sends the data in KY.  I see there is an RX; command to end the 
> TX.  I also tried a SWT16 to create a press of the XMIT button.  I cannot 
> find a syntax that works for combining the RX or SWT16 command at the end of 
> my KY command.  I do not want to use another key press.  I was hoping to do 
> it with one line of data.
> 
> The command string does not appear to work with the KY command
> 
> Neither of these formats with return to radio to RX.
> 
> KY "callsign";RX;
> or
> KY "callsign;SWT16;
> 
> Any thoughts?
> 
> Rich
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] [K3] Recent post about n1mm macros to send FSK without fancy hardware

[Bill Conkling]

There was a recent post on a reflector (don’t know which one) that listed n1mm 
function key macros for sending FSK using KY commands I think.  It didn’t seem 
to require any interface other than usual serial cable.  I am interested in 
this information.

If this will work with DX Labs as well, please include that info.

Thanks for your time.

…bill nr4c
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] [K3S] WinWarbler and RTTY (FSK)

[Bill Conkling]

I got it!

Thanks to all.  I finally got the darn thing working.  Went into the MMTTY 
settings box and set “sound+com(FSK)” os similar and all is now working.  Made 
several QSOs and then went to PSK.

Thanks…

…bill nr4c


> On Sep 24, 2015, at 4:00 PM, Bill Conkling <n...@widomaker.com> wrote:
> 
> I have been trying to get DXLabs (WinWarbler) to transmit FSK with no luck so 
> far.  I believe I have the settings right but so far no diddles.  I hear a 
> tone in the speaker and the TX LED lights up and the screen show that I am 
> transmitting, but no power out.  I am sure it is something simple but I can’t 
> seem to find it.  Oh, the screen also shows RTTY TX (Soundcard-FSK), and that 
> seems wrong.
> 
> thnx
> 
> …bill  nr4c
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] [K3S] WinWarbler and RTTY (FSK)

[Bill Conkling]

I have been trying to get DXLabs (WinWarbler) to transmit FSK with no luck so 
far.  I believe I have the settings right but so far no diddles.  I hear a tone 
in the speaker and the TX LED lights up and the screen show that I am 
transmitting, but no power out.  I am sure it is something simple but I can’t 
seem to find it.  Oh, the screen also shows RTTY TX (Soundcard-FSK), and that 
seems wrong.

thnx

…bill  nr4c
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] experience with CW and settings

[Bill Conkling]

My experience with CW decode is:

Try setting the THR to 2.  Now, with the CWT enabled press the SPOT button and 
the little signal marker should align with the index mark.  And, the marker 
should flash in step with the audio CW signal.  If it stays on too much, set 
THR up to 3, or vice versa,  If you can’t find a THR setting that is right, set 
it to a setting that keeps the little marker ON too long, and adjust RF gain 
CCW until the marker keeps step with the CW audio.  Yu should get good decode 
at this setting.  Decode will only work if the receiver is tuned spot on to the 
signal and the marker is flashing every dit nd dah.

…bc nr4c

> On Sep 24, 2015, at 6:09 PM, KC6CNN  wrote:
> 
> I am looking for someone with more experience than me with using the K3 on
> CW. 
> I have my K3 set to about 75 percent RF gain, and the width set to around
> 300. 
> ATT is off and Pre is off I do not have the dual filter on, and no afx on. I
> can spot and decode signals if they are strong. If they are weak then I can
> only decode with my ears. The THR setting when you hold down the CWT button
> is set on 3. If I set to auto is just sits there and runs jumble letters
> across the vfo b screen. 
> 
> Any help with good setting I can try would be appreciated. 
> Thanks
> Gerald - KC6CNN
> 
> 
> 
> 
> -
> KC6CNN - Gerald
> K2 # 5486
> K3 # 6294
> KX3 # 757
> --
> View this message in context: 
> http://elecraft.365791.n2.nabble.com/experience-with-CW-and-settings-tp7608260.html
> Sent from the Elecraft mailing list archive at Nabble.com.
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3 New kio board

[Bill Conkling]

I suspect they will offer it when they have a quantity available over and above 
those needed for K3S sales.  As to the price increase, most of the increases so 
far have been on the big items, mostly the radios.  Little stuff doesn’t change 
a whole lot.

…bc  nr4c


> On Sep 24, 2015, at 7:59 PM, Johnny Siu  wrote:
> 
> I want to know too because they will soon raise their prices.
> 73
> Johnny VR2XMC
>  寄件人︰ Gary 
> 收件人︰ Elecraft  
> 傳送日期︰ 2015年09月24日 (週四) 2:43 PM
> 主題︰ [Elecraft] K3 New kio board
> 
> Anyone heard of a release date for those wishing to upgrade their k3 to have 
> the USB option?
> 
> An email to Elecraft direct went unanswered.
> 
> Gary 
> __
> 
> 
> __
> Elecraft mailing list
> Home: http://mailman.qth.net/mailman/listinfo/elecraft
> Help: http://mailman.qth.net/mmfaq.htm
> Post: mailto:Elecraft@mailman.qth.net
> 
> This list hosted by: http://www.qsl.net
> Please help support this email list: http://www.qsl.net/donate.html
> Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Mac utility with K3S Puts K3S in TX mode!

[Bill Conkling]

I have been using my K3S with Win 7 so far and decided to give the Mac a chance 
to play.

Downloaded the latest utility for the Mac (Latest OSX, Macbook Pro I7 w/16gigs) 
and convinced the Mac that I really did want to open this file.  I selected the 
USB com port and my radio immediately went into TX mode and would not stop.  I 
shut down the radio.  Stated K3S again and it was still in TX.  I unplugged the 
USB, radio still in transmit. Powered off rdio, power on again, still in TX.

Now I connected the rdio to my Win 7 machine, and all is well again.

Now, plug USB back into the Mac, re-read paragraph two above.

I am a new user to the Mac and don’t know a lot about the comport details so 
this is probably something silly, but I need some assistance.  Help!

Part 2)

Just to sav e time, I hooked up the K3 to Mac with KUSB cable, and sure enough, 
it also goes to TX when connected to the Mac.  So it;s not the radio, must be a 
setting in the computer, a hiccup in the utility.



FWIW:  I have moved the modified KBPF3 and filters from my old K3 to the K3s 
yesterday and that is working just fine.

…bill c   nr4c
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Mac utility with K3S Puts K3S in TX mode!

[Bill Conkling]

A followup to my original post:

I started VMWare and ran WIN8.1 and insetalled the latest Utility.  No problems 
with the old K3.

Now to test the K3s…..

With Win *.1 on Mac, both radios are normal.

Something is not right in my Mac Utility setup.


…bill c  nr4c


 On Jul 24, 2015, at 10:22 AM, kg9hfr...@gmail.com wrote:
 
 Bill you are not alone as a MAC user and I am NOT going to purchase a WIN 10 
 box to do any work for ham radio.
 
 I have used the utility on my MacBookAir for the KX3 utility and love it.
 
 Frank KG9H
 
 
 On Jul 24, 2015, at 9:17 AM, Bill Conkling n...@widomaker.com 
 mailto:n...@widomaker.com wrote:
 
 
 I have been using my K3S with Win 7 so far and decided to give the Mac a 
 chance to play.
 
 Downloaded the latest utility for the Mac (Latest OSX, Macbook Pro I7 
 w/16gigs) and convinced the Mac that I really did want to open this file.  I 
 selected the USB com port and my radio immediately went into TX mode and 
 would not stop.  I shut down the radio.  Stated K3S again and it was still 
 in TX.  I unplugged the USB, radio still in transmit. Powered off rdio, 
 power on again, still in TX.
 
 Now I connected the rdio to my Win 7 machine, and all is well again.
 
 Now, plug USB back into the Mac, re-read paragraph two above.
 
 I am a new user to the Mac and don’t know a lot about the comport details so 
 this is probably something silly, but I need some assistance.  Help!
 
 Part 2)
 
 Just to sav e time, I hooked up the K3 to Mac with KUSB cable, and sure 
 enough, it also goes to TX when connected to the Mac. So it;s not the radio, 
 must be a setting in the computer, a hiccup in the utility.
 
 
 
 FWIW:  I have moved the modified KBPF3 and filters from my old K3 to the K3s 
 yesterday and that is working just fine.
 
 …bill c   nr4c
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 Message delivered to kg9hfr...@gmail.com mailto:kg9hfr...@gmail.com
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Mac utility with K3S Puts K3S in TX mode!

[Bill Conkling]

To all that replied.

A club member (my local Mac guy) suggested getting the latest FTDI driver, 
which I did from Elecraft website link.

I did change CONFIG/PTT settings to OFF-OFF.  All ok.  Tried starting Utility 
in SSB and CW mode with no errors.

Reset CONFIG/PTT to RTS-DTR, all still ok.  I think the driver did it.

Now, question?

If I set the PTT-KEY to OFF-OFF, can n1mm still use those lines to handle PTT 
and Keying?  I assumed not, but……..

Thanks Guy(s)

…/bill c  nr4c




 On Jul 24, 2015, at 2:17 PM, Guy Olinger K2AV k2av@gmail.com wrote:
 
 Make sure that the K3 CONFIG:PTT-KEY is set to OFF-OFF. This is to
 make sure that miscellaneous, not on purpose, states of DTR and RTS in
 the serial connection are not controlling the transmit and keying
 state of the K3.
 
 I'm not qualified to discuss how to turn off DTR and RTS on a Mac from
 the operating system. Better to set the K3 to not respond to those.
 
 Commonly, if used, DTR and RTS are controlled by applications running
 on the computer using a serial port to talk to the K3, but the state
 of those absent a program controlling them is unclear. N1MM logger and
 logger plus have a config setting to set up DTR and RTS for use or to
 force them to a given state.
 
 If you DO at some point decide to use DTR and RST for keying and/or
 PTT, you will have to completely understand and control those lines
 coming from the computer, be they Windows or Apple.
 
 Otherwise they should both be turned off in the K3 config.
 
 DTR and RTS are part of any serial connection, so this would be true
 as well using the new USB connection for K3/K3S. The DTR and RTS
 information from the computer still must either be managed or turned
 off in the config.
 
 The K3 manual version D10 has a discussion of these pinouts on page 18.
 
 73, Guy.
 
 On Fri, Jul 24, 2015 at 10:17 AM, Bill Conkling n...@widomaker.com wrote:
 
 I have been using my K3S with Win 7 so far and decided to give the Mac a 
 chance to play.
 
 Downloaded the latest utility for the Mac (Latest OSX, Macbook Pro I7 
 w/16gigs) and convinced the Mac that I really did want to open this file.  I 
 selected the USB com port and my radio immediately went into TX mode and 
 would not stop.  I shut down the radio.  Stated K3S again and it was still 
 in TX.  I unplugged the USB, radio still in transmit. Powered off rdio, 
 power on again, still in TX.
 
 Now I connected the rdio to my Win 7 machine, and all is well again.
 
 Now, plug USB back into the Mac, re-read paragraph two above.
 
 I am a new user to the Mac and don’t know a lot about the comport details so 
 this is probably something silly, but I need some assistance.  Help!
 
 Part 2)
 
 Just to sav e time, I hooked up the K3 to Mac with KUSB cable, and sure 
 enough, it also goes to TX when connected to the Mac.  So it;s not the 
 radio, must be a setting in the computer, a hiccup in the utility.
 
 
 
 FWIW:  I have moved the modified KBPF3 and filters from my old K3 to the K3s 
 yesterday and that is working just fine.
 
 …bill c   nr4c
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 Message delivered to k2av@gmail.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] [K3S] Are They Shipping Yet?

[Bill Conkling]

They charged my Credit card today, so I expect a shipment notification tonight, 
if things go as per “normal”.

…bc nr4c


 On Jul 17, 2015, at 3:50 PM, n...@comcast.net wrote:
 
 Mine just shipped yesterday. Ordered online May 22. 
 
 N9TF
 - Original Message -
 From: Keith Robinson w4...@charter.net
 To: n...@n5ge.com
 Cc: Elecraft Reflector elecraft@mailman.qth.net
 Sent: Fri, 17 Jul 2015 15:42:56 - (UTC)
 Subject: Re: [Elecraft] [K3S] Are They Shipping Yet?
 
 In fact they are
 I received mine last Monday 
 I placed my order at Dayton on Friday morning about 8:15.
 Good luck
 Keith Robinson 
 W4KTR
 
 Sent from Keith Robinson's  iPhone
 
 On Jul 17, 2015, at 09:08, Amateur Radio Operator N5GE n...@n5ge.com wrote:
 
 Has anyone received a K3S yet?
 
 Amateur Radio Operator 
 N5GE
 
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 Message delivered to w4...@charter.net
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 Message delivered to n...@comcast.net
 
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

[Elecraft] Serial cdable (USB) won't connect with K3 directly...

[Bill Conkling]

I was getting together items to take out for an event on Saturday and spent
hours trying to sort out what was happening with my USB cables.  My K3 would
not see the serial port.  As a last resort, I plugged the cable into the P3
and everything worked!  Why does it work through the P3, but not direct?

 

.bill  nr4c  (confused)

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] not receiving PSK or any SSB audio

[bill conkling]

Check RF gain settings.  Press AF knob to see RF setting.  Turn knob to show 
0.

...bill nr4c

Duh: you do have antenna connected to feed line and radio?



Sent from my Verizon Wireless 4G LTE DROID

Julie Royster jsdroys...@nc.rr.com wrote:

I had written about my husband's new problem of no longer receiving PSK
signals, and we had thought it was the FLdigi setup.
This morning I removed the computer hookups, removed the KXPA100 via the
menu following Matt's suggestion, got the latest firmware, and tried to
receive SSB, but nothing is heard.  So evidently we are not receiving
amateur radio signals of any kind at present.  With the audio all the way up
I can barely detect a commercial radio station.  Does anyone have any clues
what might be going on?
Cheers and 73,
Julie KT4JR

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] KX3 decoding CW with hand key

[bill conkling]

I think the decoding is done on output of electronic keyer.  HAND key does not 
use the keyer.

bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

WA7SPY wa7...@comcast.net wrote:

I have had my KX3 for a month or so. Love the radio. I have recently decided 
to learn and start using a bug after using a paddle for many years. How do I 
decode my sending when key 1 is selected to Hand. When key 1 is set to dot tip 
it decodes my paddle just fine as I send. It does not decode when key1 is set 
to Hand as I send. Is the just the way it is or is there a setting I am 
missing?

Thanks,
Glenn WA7SPY

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] P3 marker B transmit freq.

[bill conkling]

No, not intuitive.

MKR B is the VFO B frequency.  Often one wants to listen on the B frequency.  
It may be on another band.
SPLIT is a special case, not the norm.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Gary Smith g...@ka1j.com wrote:

Reading the P3 screen I see a station transmitting. I use Marker A 
(Green) to pin me on that desired station as soon as I tap the knob 
to QSY me to a desired signal.

I listen to the station and they say UP so I know to hold in the MKR 
button to activate B ((Magenta) I see where the last transmission is 
and I place the Magenta marker at that location and tap: The Sub Rx 
goes to that frequency where the DX was last listening but sub is not 
engaged, it just sits on that frequency and does nothing with it.

Problem is that if I don't then reach over and manually hold the 
split button on the K3 itself to have the K3 transmit on the DX 
listening frequency, I'll still keep transmitting on the DX transmit 
frequency because the K3 will not have gone split; its as if the 
procedure is halted half way and it shouldn't function this way, its 
not intuitive.

If I'm going to the effort to engage Marker B to QSY its because I 
want to transmit on the Marker B frequency. What do I have to the do 
differently to force the K3 go split to transmit on the B freq when I 
tap on MKR B? 

Thanks,

Gary
KA1J

---
This email is free from viruses and malware because avast! Antivirus 
protection is active.
http://www.avast.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3 macro's to switch mic's

[Bill Conkling]

Jeff,

I watched this nthread for a while and saw a dozen or so responses, but
no-one bothered to help you with a macro or two.  It seems that everyone has
opinions on what mic or jack and maybe which fingefr to use to press the
ON.

But, as for the macros, here goes.

These are old, but you can see what I have done and adjust accordingly.
Good luck!



TO set mic to front for Hiel  HM10-Dual

Name:   -MicFP

Macro:  MG020;CP020;MN053;DN;DN;TE-03-03+00+00+03+03+00+00;SWT11;

ASSIGN TO PF1

This will set gain to 20, the compression to 20, set mic to front, adjust TX
Equalization and set range to H


To set rear for YAMAHA CM500

Name:   -MicRPl

Macro:  MG017;CP005;MN053;DN;DN;UP;TE+00+00+00+03+03+03+03+03;SWT11;

ASSIGN TO PF2

This will set gain to 17, compression to 5, set mic to rear, adjust TX
Equalization and set range to L

NOTE:'

The setting for range H or L is a toggle.  If you press the same function
key twice, it will toggle the range.  Therefore these macros leave the Main
Menu active to show the Front/Rear and Range setting.  Just press the MENY
butoon and you are ready to go.  If the range is wrong, just press keypad #1
to toggle to the other setting.

...bill

-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of k...@comcast.net
Sent: Wednesday, March 19, 2014 12:06 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 macro's to switch mic's

Does anyone have (or know where I can get)a set of macros they would share
with me that will change a K3's mic input, along with TX eq, mic gain, comp,
etc. I'm setting my K3 up for the first time for other then DX use with the
CM500 headset. I'm going to be also using an 8 pin Kenwood MC-50. My K3 was
up to now for DX only use, but as I'm downsizing I would now like to it use
for other types of operating, and would like to use macros for the first
time to switch between the two mic's. Thanks in advance for any useful
information...  

73 Jeff KB2M


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html Message
delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] K3 macro's to switch mic's

[Bill Conkling]

No problem, Jeff.  

This combo is just that, a start.  There are some gurus on the list that
have written macros that only require one pf# key as they do some magic and
self-modify themselves to toggle the setup.  Maybe when they finish the
discussion on one verses two mics or speakers +/- phones, one of them will
enlighten us with some real useful information.

'till then, I use the macros I sent you myself, with some mods to the TE:

Good luck.

...bill nr4c

-Original Message-
From: Jeff Griffin [mailto:k...@comcast.net] 
Sent: Wednesday, March 19, 2014 8:20 PM
To: 'Bill Conkling'
Cc: elecraft@mailman.qth.net
Subject: RE: [Elecraft] K3 macro's to switch mic's

Thanks Bill this is exactly what I was looking for, some place to start. I
was wondering if anyone else has setup any macros for mic selection.
Thanks

73 Jeff kb2m 

-Original Message-
From: Bill Conkling [mailto:n...@widomaker.com]
Sent: Wednesday, March 19, 2014 5:44 PM
To: k...@comcast.net
Cc: elecraft@mailman.qth.net
Subject: RE: [Elecraft] K3 macro's to switch mic's

Jeff,

I watched this nthread for a while and saw a dozen or so responses, but
no-one bothered to help you with a macro or two.  It seems that everyone has
opinions on what mic or jack and maybe which fingefr to use to press the
ON.

But, as for the macros, here goes.

These are old, but you can see what I have done and adjust accordingly.
Good luck!



TO set mic to front for Hiel  HM10-Dual

Name:   -MicFP

Macro:  MG020;CP020;MN053;DN;DN;TE-03-03+00+00+03+03+00+00;SWT11;

ASSIGN TO PF1

This will set gain to 20, the compression to 20, set mic to front, adjust TX
Equalization and set range to H


To set rear for YAMAHA CM500

Name:   -MicRPl

Macro:  MG017;CP005;MN053;DN;DN;UP;TE+00+00+00+03+03+03+03+03;SWT11;

ASSIGN TO PF2

This will set gain to 17, compression to 5, set mic to rear, adjust TX
Equalization and set range to L

NOTE:'

The setting for range H or L is a toggle.  If you press the same function
key twice, it will toggle the range.  Therefore these macros leave the Main
Menu active to show the Front/Rear and Range setting.  Just press the MENY
butoon and you are ready to go.  If the range is wrong, just press keypad #1
to toggle to the other setting.

...bill

-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of k...@comcast.net
Sent: Wednesday, March 19, 2014 12:06 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 macro's to switch mic's

Does anyone have (or know where I can get)a set of macros they would share
with me that will change a K3's mic input, along with TX eq, mic gain, comp,
etc. I'm setting my K3 up for the first time for other then DX use with the
CM500 headset. I'm going to be also using an 8 pin Kenwood MC-50. My K3 was
up to now for DX only use, but as I'm downsizing I would now like to it use
for other types of operating, and would like to use macros for the first
time to switch between the two mic's. Thanks in advance for any useful
information...  

73 Jeff KB2M


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html Message
delivered to n...@widomaker.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com

Re: [Elecraft] Power Cable / Adapter

[bill conkling]

Elecraft sells the power cable with the 2.1 connector on one end and nothing on 
the other end so you can add the connector(s) of your choice.

...bill. nr4c

Sent from my Verizon Wireless 4G LTE DROID

Dave Cox dcoxm...@gmail.com wrote:

Does anyone know where I can purchase a fused 12v power cable for my KX3
that has a 2.1.mm power plug on one end and a pair of F1 connectors on the
other end. It will connect my Elecraft KX3 transceiver to a 7aH SLA
battery.

Dave
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Battery voltage on KX3 seems high...

[bill conkling]

When the external power source is higher than internal batts, radio will use 
the external supply.  The internal batts are unused and will indicate open 
circuit voltage.  When external source is not used, internal batts have some 
load and voltage drop.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Don Wilhelm w3...@embarqmail.com wrote:

What is the current and voltage rating of the power supply that you have 
connected to the KX3?  That is an important parameter to answer your 
question.

73,
Don W3FPR

On 3/13/2014 10:49 PM, Andrew Robertson wrote:
 I have some NiMH batteries installed in my KX3, and while it is plugged into 
 a power supply or fully charged 12v battery the rechargeable batteries 
 report a voltage of 10.8v.  If I remove external power the KX3 reports 
 internal battery voltage at 10.2v.  Is the KX3 trickle-charging the internal 
 batteries when external power is applied, and if so what is the trickle 
 charge rate?



__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] [k3] Mic Gain: Option 7

[bill conkling]

And tap 7 for an additional 10db of gain!

I'm sure  Its in the book!

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Sam Morgan k5oai@gmail.com wrote:

tap MENU to get into MAIN
locate MIC SEL
tap DISP
read the info that scrolls across VFO B
it will tell you about toggling Boost Hi/Lo
by taping Number 1 on the number pad

On 3/12/2014 8:40 PM, John wrote:
 I'm trying to setup a set a Radio Sport headset, with the M350 Electret
 microphone. The mic is connected to the K3 rear panel mic jack. The
 Arlan instructions recommend using Option 7 for +10 DB of additional
 Mic Pre-amp gain for close-talk mics.

 How do you set Option 7? What menu is it in?

 Thanks,
- 73, John, N0TA


-- 
GB  73
K5OAI
Sam Morgan
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] [k3] Mic Gain: Option 7

[bill conkling]

Yes the ref to 3 is a long overdue edit.  I have used 7 to work with my Heil 
HM12 in front panel.  Was unaware it doesn't work for rear jack.  CM500 plugged 
in there, no need.

...bc

Sent from my Verizon Wireless 4G LTE DROID

Sam Morgan k5oai@gmail.com wrote:

Page 20 K3 Owner's man D10.pdf

MIC
MONO; hi- or low-Z
This jack accommodates an electret or dynamic
mic. Use MAIN:MIC SEL to select the rear panel
mic (RP). Tap 1 to turn on Low or High mic gain
range. Tap 2 to turn bias on/off (see pg. 28 for
recommendations based on mic type).
For the front-panel mic only, additional microphone
gain can be enabled by tapping 3 . Use this only for
very low-output mics.

page 52 K3 Owner's man D10.pdf
MIC SEL
Mic/line transmit audio source, mic gain range, and mic bias. Source 
selections:
FP (front panel 8-pin MIC jack), RP (rear panel 3.5 mm MIC jack), and 
LINE IN
(rear-panel LINE IN jack). Tap 1 to toggle between .Low and .High mic 
gain range
for the selected mic. Tap 2 to turn mic BIAS on/off (turn on for 
electret mics).
For the front-panel mic only, tap 3 to turn on an additional gain stage. 
Use this only
with very low-output mics. An apostrophe will appear after the H, e.g. H’ .



only place I find tap 7 in the manual is under FLx BW on pg 55
also mentioned on pg 24


however when in the MIC SEL menu for the front panel mic
taping 3 gives a N/A result

taping 7 *WILL* give the desired mic boost for the front panel mic

taping 3 or 7 gives a N/A when rear mic is selected

I just checked in the ERRATA for the K3 Owners manual and it's not there 
either

looks like there needs to be an editing job in the manual ;-)

On 3/13/2014 7:40 AM, bill conkling wrote:
 And tap 7 for an additional 10db of gain!

 I'm sure  Its in the book!

 ...bill nr4c

 /Sent from my Verizon Wireless 4G LTE DROID/


 Sam Morgan k5oai@gmail.com wrote:

 tap MENU to get into MAIN
 locate MIC SEL
 tap DISP
 read the info that scrolls across VFO B
 it will tell you about toggling Boost Hi/Lo
 by taping Number 1 on the number pad

 On 3/12/2014 8:40 PM, John wrote:
   I'm trying to setup a set a Radio Sport headset, with the M350 Electret
   microphone. The mic is connected to the K3 rear panel mic jack. The
   Arlan instructions recommend using Option 7 for +10 DB of additional
   Mic Pre-amp gain for close-talk mics.
  
   How do you set Option 7? What menu is it in?
  
   Thanks,
  - 73, John, N0TA


-- 
GB  73
K5OAI
Sam Morgan

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KAT3 tuner and KXAT100 tuner specs question

[bill conkling]

Suspect mostly packaging.  I've wondered the same thing.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

W0FK llader...@earthlink.net wrote:

The KAT3 used in the K3 and KXAT100 tuner used in the KXPA100 amp appear to
have the same specs on paper. Both handle 100 watts and up to a 10:1 SWR
(KXPA100 lists 5:1 on 160 and 6, unsure about the KAT3). 

What are the differences between the two tuners, if any?

Lou, W0FK



-
St. Louis, MO
K3 #'s 7463 and 2513, P3 #620, KX1 #1517, KX3 #0036

--
View this message in context: 
http://elecraft.365791.n2.nabble.com/KAT3-tuner-and-KXAT100-tuner-specs-question-tp7585208.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] ELECRAFT K3 - LAPTOP SINGLE RS232 PORT - WITH WRITELOG AND PROPOSED P3 OPERATION

[bill conkling]

Buy it and the KXV3a board and install both.  Have fun.  

Download and read the manuals for each to see what you're up against.

...nr4c

Sent from my Verizon Wireless 4G LTE DROID

JOHN POWELL powell.j...@xtra.co.nz wrote:

Presently I am running the above, primarily as the K3-Laptop-Wtitelog 
operation, and wanting to interface the P3 into the station configuration. The 
vexing question is how ?, hence this enquiry for a possible
solution . Your thoughts will be greatly apreciated to relieve a somewhat 
tired brain !!.

Thanks for any help
73.
John Powell. ZL1BHQ 
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 - Mono or stereo speaker

[bill conkling]

If, and only if you have Speakers set to 1, you can use a mono plug.  DONOT 
set speakers to 2 with it inserted however.  Smoke will escape and you will 
be faced with a repair.

My rule is: NEVER plug a mono plug in the Speaker jack, EVER!

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Edward F. Steinfeld edw...@go-embedded.com wrote:

I have an external speaker with a monaural plug. If I set Speakers to 1 can
I use the mono plug? The write-up is slightly confusing to me.

73,
KB1ZJK - Ed

Edward F. Steinfeld  KB1ZJK
25 Arbor Glen Drive
Stow, MA 01775-1258
Home: (978)897-3127
Cell: (978)376-3146
mailto::edw...@go-embedded.com
http://www.go-embedded.com http://www.go-embedded.com/ 
http://en.wikipedia.org/wiki/Mount_Steinfeld 

 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 - new release of HRD

[bill conkling]

I must have entered the wrong reflector by mistake.

...bc nr4c

Sent from my Verizon Wireless 4G LTE DROID

Rick Ruhl ric...@w4pcsoftware.com wrote:

Tim, this is how misinformation is spread.  We have to fix issues one at a
time and sometimes those fixes will cause other issues.. the nature of
programming.  But to say we are in no hurry is a total falsehood.  Erik,
Mike, and I are working 12-16 hours a day on the product and good code, like
fine wine, takes time. 


As for LPBridge

1. Im not very fond of port splitter programs.  One DCE to one DTE device is
the RS-232 standard

2. F6DEX and N8LP need to modify LP Bridge to support Unicode strings.  They
are still MCSB and Microsoft is totally going to Unincode

Asking us to make 6.2 work with LpBridge is like asking Microsoft to fix
Windows for something that they broke in 8.X with HRD. (and they did).  When
we contacted Microsoft, they said we had to modify our code to match Windows
8.

So the LpBridge guys need a Unicode version to work with HRD 6.

And there is no they, there is US!  Rick, Mike, Tim, Erik, Erin, Jon, V,
Gordy, etc etc

As for your question in ticket number 859567, all support for 6.2 is being
done in the forum and I see no posts in there..  I know there was one on the
yahoo group, but that is not official HRD support.

So the answer is, look at some of my posts in this thread from earlier and
you'll see the fixes...




-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of KQ8M
Sent: Monday, March 03, 2014 2:02 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 - new release of HRD

Willi was a paid user of HRD. 6.2 is nothing but bugs. They call it a public
release. They have now released the next Beta release which is supposed to
fix some of the K3 problems. When I asked what they fixed I received
absolutely no response. The 6.2 release is not compatible with LP-Bridge
whereas previous versions were. I stopped upgrading at that point. A lot on
their bug list has been there for some time and they seem in no hurry to fix
anything.


73,
Tim Herrick, KQ8M
Charter Member North Coast Contesters
k...@kq8m.com

AR-Cluster V6 kq8m.no-ip.org
User Ports: 23, 7373  with local skimmer, 7374 without local skimmer Server
Ports: V6 3607, V4 Active 3605, V4 Passive 3606


-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Joe Subich, W4TV
Sent: Sunday, March 02, 2014 9:42 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 - new release of HRD


It appears that a public beta has been released for paid users.  If you want
to know what is in it - beyond the short list on the web site - I suggest
you become a paid user to gain access to the software:
http://www.hrdsoftwarellc.com/downloads/default.html

73,

... Joe, W4TV


On 3/2/2014 9:19 PM, Bill W2BLC wrote:
 Of course they are always making changes -  it is my understanding 
 that Beta 6.2 has recently been released.

 As you are on the company test team, you are uniquely qualified and 
 informed as to what changes, specifically, have been made to correct 
 the deficiencies in HRD/K3 operation (using 5.xx versions)? Changes 
 that will have me clamoring to purchase the latest version of HRD.

 For example: Are there more button assignments available? Same 
 question for slider controls? Also, in the past, some button 
 selections did not result in the button lighting while others did - 
 do they now all light when selected?

 Thanks,

 Bill W2BLC K-Line

 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net Please help support this email
 list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: 

Re: [Elecraft] kat/kpa500 cable

[bill conkling]

Yeah.  Right 'off the shelf' from Elecraft.(grin)bc

Sent from my Verizon Wireless 4G LTE DROID

Jeff Griffin k...@comcast.net wrote:

Is there an off the shelf cable I can use besides the 850463 Optional KAT500
to KPA500 Cable ? Thanks for any alternatives...

73 Jeff kb2m


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] The case for a Panadapter - opinions, please?

[bill conkling]

With either the waterfall or peak hold displays, you get to see where other 
stations were (and hopefully will come back,) so you don't pass them while 
tuning blind.

I really like my P3.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Jim Lowman jmlow...@sbcglobal.net wrote:

I'm basically a SP operator, especially in contests.  I've found that 
calling CQ is something of a waste of valuable time.

When I see options like the Panadapter, or bandscopes from other 
manufacturers, I get the metaphor of fishing in a stocked pond.

So, for those of you who have this option, could you describe how it has 
assisted you?
In another message, someone mentioned that weak stations outside of the 
passband could be missed, which is a good point.

BTW, I'm not opposed to giving the good folks at Elecraft more of my $$$ 
if this is a good idea.

Thanks in advance and 73 de Jim - AD6CW
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Fw: SSB issue K3

[bill conkling]

What mic are you using?

Did you set up the mic according to the procedure in the manual?

You must keep the mic in the same relative position while you speak and keep 
the voice power constant.  Often when making test such as this, we move our 
head to get better view of meter and turn away from the mic.  A headset with 
boom mic is useful for this test.

Good luck.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Mark Pride mpride...@yahoo.com wrote:

Thanks for the initial round of comments and suggestions.

The radio did go through the calibration as per the instructions - worked fine.

Symptoms: Full CW power yet on SSB with mic at 28 and comp at 25, initially 
full power out, then quickly drops off to say 10 to 15 watts.  Have tried the 
ATU and no change - thinking it was a problem with SWR and the radio is 
protecting itself (of course on the same band, the CW power is stable with or 
without the ATU).  Almost behaves like there is some AGC action and drives the 
power down.  But then it will jump back up sporadically. Also the quality of 
the audio is weird (not sure how to describe). Don't believe the connectors 
are intermittent with the mic connection.

I have a second K3 and set both MENU and CONFIG items the same - still the 
problem continues.

The mic connection has been made directly to both the front and the rear 
connections - no change
With or without ATU on - no change

Different mics tried and no change.
Swapped power supplies (one K3 to the other) no change

Suggestions now?

Regards,
Mark, K1RX
 




On Monday, February 24, 2014 11:03 PM, Mark Pride mpride...@yahoo.com wrote:
  
Yes did the cal and worked fine. Tried both front and rear mic connections - 
same result 


Regards, 
Mark,  K1RX 

Please excuse any typos here. 


Matt Zilmer mzil...@roadrunner.com wrote:


Have you tried the transmit power calibration procedure on your newer
K3?  I can tell you from experience that it is an essential item on a
K3 owner's list of things to do before going on the air with a new
KPA3.

73,
matt W6NIA

On Mon, 24 Feb 2014 18:53:21 -0800 (PST), you wrote:

Just installed the KPA3 module, went from 10 watts to 100 watts - good.

On CW, full power out, no problem.

On SSB, initial voice peak drives power out to the max (100 w) but within 
moments, the power drops way down to say, 10 or 15 watts, then randomly 
spikes back up but not as a function of voice peaks.  Is there a setting I 
should change to get that constant SSB power out?  Seems there is something 
fundamentally wrong with the SSB mode on this particular radio.

I have another K3 that has been in use for several years (no problems) and 
made the settings the same on both but still SSB power levels vary all over 
the place with the new K3.

Some advice from experts here please?  Thanks in advance!


Regards,
Mark, K1RX
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net/
Please help support this email list: http://www.qsl.net/donate.html
Matt Zilmer, W6NIA
--
Give me six hours to chop down a tree and I will
spend the first four sharpening the axe. -A. Lincoln
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KPA500 Default Band?

[bill conkling]

What's the big deal?  Once the K3 is on, it should jump to whatever band the K3 
is set to??

The KX3 won't tell the KPA500 what band till it spits out some ref.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Jim Bennett w6...@mac.com wrote:

So, as Lyle (KK7P) and Brian (K3KO) are saying, this is due to (1) having the 
KPA500 set to K3 (I do), and after the amp sits and capacitors discharge, 
there is no voltage coming through the acc connector and the amp goes to 60 
meters. 

Well, if that's the case then I guess there isn't much that can be done about 
it. Sigh...

Tnx, Jim
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 issue in CW mode

[bill conkling]

Turn on VOX...

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Joel Black w4...@charter.net wrote:

I think the T just indicates CW decode. Hold the TEXT DEC button and 
then rotate the VFO B knob until you get OFF in the VFO B section of the 
display.

73,
Joel - W4JBB

On 2/23/14, 10:44 PM, Ham Radio wrote:
 In CW mode it still will not get any power out and I am stuck with the 
 T in the lower right part of the display.

 CW was working fine until I went to 2m and then returned back to 6m 
 and then subsequently to HF.  All other modes are working fine.

 Any thoughts or ideas of what I have done would be helpful.

 Thanks,

 Keith
 AK6ZZ

 -Original Message- From: Ham Radio
 Sent: Sunday, February 23, 2014 7:46 PM
 To: Elecraft Group
 Subject: Re: [Elecraft] K3 issue in CW mode

 I figured out the + now looking to get rid of the T.

 Keith
 AK6ZZ

 -Original Message- From: Keith Heimbold
 Sent: Sunday, February 23, 2014 6:12 PM
 To: Elecraft Group
 Subject: [Elecraft] K3 issue in CW mode

 I just turned on my 2m transverter and when I went back to 6m my CW 
 doesn't
 work. The display shows + and T and I don't get any power out in CW. 
 Other
 modes work fine.  I looked at instructions but couldn't figure it out.

 Keith
 AK6ZZ

 Sent from my iPhone please excuse typos
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html

 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 issue in CW mode

[bill conkling]

Nope, the T indicates TEXT DECODE


...nr4c

Sent from my Verizon Wireless 4G LTE DROID

Jim Sheldon w...@cox.net wrote:

Nope, if the T is showing, the rig is in TEST mode.  Hold down the right 
hand portion of the MODE switch until it goes away and it'll put out power 
again.

Jim - W0EB

 Turn on VOX...

 ...bill nr4c

 Sent from my Verizon Wireless 4G LTE DROID

 Joel Black w4...@charter.net wrote:

 I think the T just indicates CW decode. Hold the TEXT DEC
 button and then rotate the VFO B knob until you get OFF in the
 VFO B section of the display.

 73,
 Joel - W4JBB

 On 2/23/14, 10:44 PM, Ham Radio wrote:
 In CW mode it still will not get any power out and I am stuck
 with the T in the lower right part of the display.

 CW was working fine until I went to 2m and then returned back
 to 6m and then subsequently to HF.  All other modes are working
 fine.

 Any thoughts or ideas of what I have done would be helpful.

 Thanks,

 Keith
 AK6ZZ

 -Original Message- From: Ham Radio
 Sent: Sunday, February 23, 2014 7:46 PM
 To: Elecraft Group
 Subject: Re: [Elecraft] K3 issue in CW mode

 I figured out the + now looking to get rid of the T.

 Keith
 AK6ZZ

 -Original Message- From: Keith Heimbold
 Sent: Sunday, February 23, 2014 6:12 PM
 To: Elecraft Group
 Subject: [Elecraft] K3 issue in CW mode

 I just turned on my 2m transverter and when I went back to 6m
 my CW doesn't
 work. The display shows + and T and I don't get any power out
 in CW. Other
 modes work fine.  I looked at instructions but couldn't figure
 it out.

 Keith
 AK6ZZ

 Sent from my iPhone please excuse typos
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:
 http://mailman.qth.net/mmfaq.htm Post:
 mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net
 Please help support this email list:
 http://www.qsl.net/donate.html

 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:
 http://mailman.qth.net/mmfaq.htm Post:
 mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net
 Please help support this email list:
 http://www.qsl.net/donate.html
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:
 http://mailman.qth.net/mmfaq.htm Post:
 mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net
 Please help support this email list:
 http://www.qsl.net/donate.html


 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:
 http://mailman.qth.net/mmfaq.htm Post:
 mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net
 Please help support this email list:
 http://www.qsl.net/donate.html

 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:
 http://mailman.qth.net/mmfaq.htm Post:
 mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Reverting from FW 4.83 to the Previous Release Version

[bill conkling]

Yes.  Check the web site download pages and there should be a Archive of 
earlier releases.

Also check for earlier betas.  Beta with same number as production are same.

...bill

Sent from my Verizon Wireless 4G LTE DROID

Phil Wheeler w...@socal.rr.com wrote:

My K3/P3 arrived Friday. I listened a bit, mostly 
on SSB but some on CW. I don't recall any issues 
with how it sounded to me.

Yesterday afternoon I finally got around to 
installing the K3 Utility and P3 Utility on my 
shack Win 8.1 PC. I discovered that MCU 4.83 had 
been released and upgraded from the version my K3 
#8004 was delivered with.  All that went well -- 
and I noticed that the DSP firmware was updated, 
too, from msgs on the LCD.

Last night I again listened to more CW and with 
some settings the audio seemed different, for 
lack of a better term. Most likely this is due to 
my newness to the K3 and some significant hearing 
impairments (stone deaf in one ear and the good 
one isn't so great), but I'd like to wring it out 
and see if there is/was a difference.

So I'd like to try installing the previous release 
version (4.67 or 4.76) on my K3 and do some A-B 
testing. The problem is that since my K3 came with 
the earlier version installed, I likely do not 
have the needed firmware files in my computer to 
be loaded -- though reading at the Elecraft 
website it looks possible to do such a reversion 
if you do have them in your computer

My questions: Are the needed earlier files 
available for download, and if they are, which 
files are they and how do I go about telling the 
K3 utility to load them (I assume it's akin to 
installing a beta version but as a K3 owner of 48 
hours I've not had the opportunity to load beta 
firmware).

73, Phil w7ox
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 mini ?

[bill conkling]

Read carefully.  Reference to K3/0 Mini.  Its a front panel only for remote 
operation of a K3/10 or K3/100 

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Alan Price w1...@hotmail.com wrote:

How does it differ from the KX3?
 73
Alan
W1HYV
 
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 external speaker output dead

[bill conkling]

If you used s stereo plug, how is it wired?  Should be tip and shield for ONE 
speaker.

Also is SPKR + PH set to YES?  If this is NO then you won't have any speaker 
output.  If the internal spkr works this isn't a problem.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

a...@sbcglobal.net wrote:

I recently purchased 2 replacement K3 speakers to make tuned port enclosures 
for CW audio.  
Plugging one of the speakers to the rear panel jack (via 3.5mm stereo plug) to 
test resulted in no output. 
Had the config SPKRS = 1   Rear jack worked fine last time I tried an external 
speaker.   Full audio 
output is fine on the internal speaker.   Anyone reading had this issue?  Any 
ideas?
 
73,
Mike AC5P 
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3/KPA500/KAT500 revs 4.83/1.38/1.58

[bill conkling]

Sounds great but most of the time my KAT500 won't turn on until I turn on the 
K3.

What now?

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Jack Brindle jackbrin...@me.com wrote:

The KAT500 needs to be powered on whenever the K3 is on in order to avoid 
loading the Auxbus. It can be powered up at the same time, but must be on 
before the K3 completes its initialization.

The KPA500 has no restriction, and can be powered on any time before or after 
the K3 is turned on.

Jack Brindle, W6FB

On Feb 21, 2014, at 2:23 AM, Stephen Prior eastbrantw...@gmail.com wrote:

 Chuck,
 
 I seem to remember reading that the order of turning on the K-line is
 important.  I always turn on the KAT500, then the KPA500 followed by the
 K3/P3.  I have not had any issues doing things in that order.  Maybe this
 is why you had the 'problem'?
 
 73 Stephen G4SJP
 
 
 On 21 February 2014 10:19, ke9uw c-haw...@illinois.edu wrote:
 
 Oh yes, I remember now yesterday I got a soft fault on the KPA500. I turned
 on the K3, the KAT500 went to the pretuned setting on 40M and then I turned
 on the KPA500 and clicked it into operate.
 I said one word and the KPA500 went to standby. No red lights. I returned
 it to operate and everything worked well. Forgot about that...not a
 problem,
 but don't know why it did that.
 
 
 
 -
 Chuck, KE9UW
 --
 View this message in context:
 http://elecraft.365791.n2.nabble.com/K3-KPA500-KAT500-revs-4-83-1-38-1-58-tp7584490p7584507.html
 Sent from the Elecraft mailing list archive at Nabble.com.
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] (no subject)

[bill conkling]

My experience says either/or.  But I did mine in reverse order of cost.  Get 
the most expensive ones first.

...bill

Sent from my Verizon Wireless 4G LTE DROID

John Saxon johnbsa...@yahoo.com wrote:

I have a K3/10 with no add-ons, and now am ready to get a KPA3 100W amp  KAT3 
tuner, to install myself.  I would rather not purchase them at the same time.  
Is there a more favorable order to get them?  Amp first or tuner first?  I 
suspect there may be some construction issues that would favor one over the 
other to be acquired first.

Thanks  73,
John
K5ENQ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3/KPA500/KAT500 revs 4.83/1.38/1.58

[bill conkling]

It's plugged into the same PS as the K3.

...bill

Sent from my Verizon Wireless 4G LTE DROID

Jack Brindle jackbrin...@me.com wrote:

You might want to say how you have the KAT powered. In my station I have a 
relay-switch power panel that I built. The relay is powered by the K3’s 12V 
output jack. When the K3 turns on, it powers the relay, which the switches 12V 
power to the various station boxes, including the KAT500. By the time the K3 
is ready to talk to the KAT, it is awake and listening, as is the KRC2, P3, 
etc...


Jack B, W6FB


On Feb 21, 2014, at 5:44 PM, bill conkling n...@widomaker.com wrote:


Sounds great but most of the time my KAT500 won't turn on until I turn on the 
K3.


What now?


...bill nr4c


Sent from my Verizon Wireless 4G LTE DROID



Jack Brindle jackbrin...@me.com wrote:

The KAT500 needs to be powered on whenever the K3 is on in order to avoid 
loading the Auxbus. It can be powered up at the same time, but must be on 
before the K3 completes its initialization.

The KPA500 has no restriction, and can be powered on any time before or after 
the K3 is turned on.

Jack Brindle, W6FB

On Feb 21, 2014, at 2:23 AM, Stephen Prior eastbrantw...@gmail.com wrote:

 Chuck,
 
 I seem to remember reading that the order of turning on the K-line is
 important.  I always turn on the KAT500, then the KPA500 followed by the
 K3/P3.  I have not had any issues doing things in that order.  Maybe this
 is why you had the 'problem'?
 
 73 Stephen G4SJP
 
 
 On 21 February 2014 10:19, ke9uw c-haw...@illinois.edu wrote:
 
 Oh yes, I remember now yesterday I got a soft fault on the KPA500. I turned
 on the K3, the KAT500 went to the pretuned setting on 40M and then I turned
 on the KPA500 and clicked it into operate.
 I said one word and the KPA500 went to standby. No red lights. I returned
 it to operate and everything worked well. Forgot about that...not a
 problem,
 but don't know why it did that.
 
 
 
 -
 Chuck, KE9UW
 --
 View this message in context:
 http://elecraft.365791.n2.nabble.com/K3-KPA500-KAT500-revs-4-83-1-38-1-58-tp7584490p7584507.html
 Sent from the Elecraft mailing list archive at Nabble.com.
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html
 
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net
 
 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] I/Q display on Iphone/Ipad

[bill conkling]

Prob too late but the app is iSDR.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Ron Gould kd...@comcast.net wrote:

I saw spectral display Electcraft has done with KX3 using a iMic into a iPad.  
Does anyone know the name of the application being used to do this?  Thanks.  
Sending response off list is fine. Thanks and 73’s
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] 270V ERR KPA500

[bill conkling]

Mine did this right from the start.  Trace the 270 volt wire from PS go amp 
module, thru the Z bracket.  Somewhere the 270 is going low.  Mine had a bad 
cap on the circuit board near the 270 V connector.

... bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

DGB ns9i2...@bayland.net wrote:

I'm getting this error from my amp when I turn it on and set it in the 
OPER mode. Then it requires shutoff via the rear switch to shut it off. 
I've been running it off 120v and has been working fine.

What do I need to look for?

73 Dwight NS9I
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] 270V ERR KPA500

[bill conkling]

Measure the voltage at end of wire thru Z bracket while not connected to the 
amp module.  And also connected.  Should be 270 V.  Mine was 12 V when 
connected.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

DGB ns9i2...@bayland.net wrote:

The interlock switch and hardware checks out good.

I've had this amp for a couple of years.

Removing the p.s. now to check it out as Bill mentioned.

thanks 73 Dwight NS9I

On 2/12/2014 11:44 AM, Brian Alsop wrote:
 Or the interlock hardware is installed wrong.

 73 de Brian/K3KO

 On 2/12/2014 17:28, bill conkling wrote:
 Mine did this right from the start.  Trace the 270 volt wire from PS 
 go amp module, thru the Z bracket. Somewhere the 270 is going low.  
 Mine had a bad cap on the circuit board near the 270 V connector.

 ... bill nr4c

 Sent from my Verizon Wireless 4G LTE DROID

 DGB ns9i2...@bayland.net wrote:

 I'm getting this error from my amp when I turn it on and set it in the
 OPER mode. Then it requires shutoff via the rear switch to shut it off.
 I've been running it off 120v and has been working fine.

 What do I need to look for?

 73 Dwight NS9I
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html

 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html


 -
 No virus found in this message.
 Checked by AVG - www.avg.com
 Version: 2012.0.2247 / Virus Database: 3697/6586 - Release Date: 
 02/12/14





 -
 No virus found in this message.
 Checked by AVG - www.avg.com
 Version: 2012.0.2247 / Virus Database: 3697/6586 - Release Date: 02/12/14

 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Why won't my K3 work split in FSK-D mode?

[bill conkling]

I don't think it's supposed to.  I don't remember why.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Dick Frey k4xu.1...@gmail.com wrote:

-- 
Dick - K4XU
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] [Elecraft_K3] curious behavior of the K3/P3, etc.

[bill conkling]

Hi/lo cut is usually used for ssb operation.  But I think K3 cw is lower than 
carrier so same applies.

...bill

Sent from my Verizon Wireless 4G LTE DROID

Scott Monks cq_dx_de_aa...@yahoo.com wrote:

Sorry Bill and all--I was describing the behavior when on CW.  I more often 
use these adjustments on CW, but if it is important for understanding the 
question (and for me to understand what's going on!) I will check with SSB 
when I get home this evening.


Thanks,

Scott  AA0AA


From: bill conkling n...@widomaker.com
To: Scott Monks cq_dx_de_aa...@yahoo.com 
Sent: Tuesday, February 11, 2014 9:55 AM
Subject: Re: [Elecraft] [Elecraft_K3] curious behavior of the K3/P3, etc.


On question 2, what band?  On LSB bands, HiCut is the lower freq edge as its 
the farthest away from the center carrier, hence higher freq audio.


...bill nr4c


Sent from my Verizon Wireless 4G LTE DROID



Scott Monks cq_dx_de_aa...@yahoo.com wrote:

Now before you guys think I too am complaining--no, I just have a curious mind!

Two questions that I am sure you more experienced can help me with:

1. When I begin narrowing the DSP down, on filter 1 (2.7, std, offset -0.84) 
only the lower freq side moves.  The DSP switches to the 2.1 filter, reacting 
the same, but when it narrows to about 1.10 (within filter 2; 2.1, offset 0.0) 
it changes so that both low and high move equally.  Even narrowing continues 
through the 700 and 400 Hz filters.  The reverse occurs in the same way.   I 
have checked the offsets with the K3 program, and they are set as required.  
On the K-3 display the bar-thing always seems to move equally on both sides. 
 Is this normal?

2. When seen on the P-3, on hi-cut-lo, if I move the lo side, the higher freq 
side moves, and if I move the hi side, the lower freq side moves.  On the K-3 
display the expected side moves.  Again, is this normal?

I have the last production software installed.  This was first noticed when I 
got the P3 and a big screen, when in a contest I wanted to shift the 
receiver up to avoid a disturbing signal and found I had to move the hi side 
to move the lo side!  Now I am accustomed and just watch my screen to make 
sure I am moving outside of the interfering peak.

These only bother me because I know there must be a reason but I don't why 
it happens!  If curiosity is going to kill the cat, don't tell me and I will 
just continue to be happy with my partial K-line!

Thanks for your patience,
Scott  AA0AA
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html



__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Issue with the KX3, KXPA100 and software on 17m...can hear the serial commands

[bill conkling]

Are you using a RS232 cable or a USB to serial cable?

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

tom...@videotron.ca wrote:

Hi I was wondering if anyone else has this issue:

I have the KX3 and the KXPA100 connected through the wiring kit and I am 
connecting to the combo with Ham Radio Deluxe or Win4K3Suite. If I go to 17m, 
and the software is running I can literally hear the serial commands in my 
headphones. It sounds like tons of clicks, and chirping noises on 17M only. I 
also hear it on 12m but much quieter.It also shows up on the s-meter as an s-5 
pulsing. If I turn off the KXPA100, the noise goes away. 
I have tried a different serial port cable connected to a different port and 
there is no difference.


It is definitely coming from the KXPA100. I never had this before I installed 
the amp.




Can anyone here confirm to me if this is just my setup or are other 
experiencing the same issues?
Thanks, Tom va2fsq
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 4.81 beta anomally

[bill conkling]

I think there two levels of software we should consider.
1-  FIELD TEST - Software available to selected field testers which should be 
discussed among testers and Elecraft techs.  This includes revs that are 
supplied to a more expansive group via direct email to Eric or Wayne.

2 - BETA...  Software announced on list to all and available from Elecraft BETA 
folder on web site for download.  As this is avail to all, comments should be 
public.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Lynn W. Taylor, WB6UUT k...@coldrockshotbrooms.com wrote:

I've conducted many beta test cycles over the past couple of decades.  I 
have software in beta now.

Part of my beta test agreement states that Beta software is broken.  
Your job is to help find the problems so they can be fixed before 
production.

More than a few times I've withdrawn functions and features because they 
didn't prove to be useful, sometimes spectacularly so.

It's pretty common for a beta test agreement to include a non-disclosure 
clause.

Particularly now, with the internet, bugs can develop a life of their 
own, even if they're never present in released software.

I don't know what Elecraft does, but software released for beta testing 
is reasonably subject to the terms and conditions that Elecraft chooses 
-- and as widely or narrowly as they wish.

Bugs found in testing have practically no bearing on ones' investment -- 
except perhaps as a distraction.  I'd argue that a wide-open beta 
actually reduces the value of your investment.

73 -- Lynn

On 2/8/2014 3:57 PM, Don Wilhelm wrote:
 Beta releases are intended to allow those who are willing to be early 
 testers of new firmware to participate in evaluating that new level.  
 If there are no significant problems, that level may be advanced to 
 production, but if there are problems discovered, that firmware level 
 will never 'see the light of day' other than the beta version. 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 and the LDG AT 600 Pro II

[bill conkling]

Not avail for K3.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Robert Biamonte steamer...@mac.com wrote:

Of course I just thought of the phraseology, I am looking for a control cable 
like the ones made for Yaseu and Kenwood. This cable would reduce the K3 power 
to Tune level and return the power to normal when the Tune button is released 
on the K3. Operating like the built in antenna tuner on the K3.


73
Rob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] CW memory problem

[bill conkling]

You must have checked few version and then pressed M1 and thus set M1 to check 
version.

Done that

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Carl Yaffey cyaf...@gmail.com wrote:

I used the K3 utility to set all 4 CW memories. M1 has my call. I’ve been 
using that one extensively lately. Today, after an hour of calling W1AW/KH6, 
suddenly pressing M1 gives me this:
Main display: uC 04.67
VFO B display: FW REV5

The other 3 memories still work fine. I went into the utility and found my 
call still in M1. I re entered it and saved.
Problem is still there. I need a clue, please.
73,
Carl Yaffey  K8NU
Banjo, guitar, bass, mandolin, dobro. 
recording studio.
cyaffeyno_s...@gmail.com 
614 268 6353, Columbus OH
http://www.carl-yaffey.com
http://www.grassahol.com







__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] CW memory problem

[bill conkling]

I think he just reprogramed the M1 button as another pf buttonTo 
display fw rev.

...bill

Sent from my Verizon Wireless 4G LTE DROID

Dick Dievendorff d...@elecraft.com wrote:

There are two banks of 4 memories, and you switch between them by a HOLD of
the REC button. 

Maybe you've somehow switched banks by holding the REC button?

See page 30 of the owner's manual, CW Message Record/Play

73 de Dick, K6KR

-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Carl Yaffey
Sent: Wednesday, February 05, 2014 4:53 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] CW memory problem

I used the K3 utility to set all 4 CW memories. M1 has my call. I've been
using that one extensively lately. Today, after an hour of calling W1AW/KH6,
suddenly pressing M1 gives me this:
Main display: uC 04.67
VFO B display: FW REV5

The other 3 memories still work fine. I went into the utility and found my
call still in M1. I re entered it and saved.
Problem is still there. I need a clue, please.
73,
Carl Yaffey  K8NU
Banjo, guitar, bass, mandolin, dobro. 
recording studio.
cyaffeyno_s...@gmail.com 
614 268 6353, Columbus OH
http://www.carl-yaffey.com
http://www.grassahol.com







__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K-3

[bill conkling]

Check voltage to radio at full power.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

gmuller...@aol.com wrote:

I am having trouble with the K-3. When I xmit for a period of time the  
Display starts to fluctuates with the modulation in my voice. The longer I am 
on  the more rapidly it fluctuates till it shuts down the K-3. I have removed 
 all external cables and even done this with a dummy load. I have a DX  
engineering Current chock at the entrance to the house and at the antenna. I 
am 
 told that people can here RF on the signal. Any suggestions?
 
Gerald Muller KF5EYC
gmuller...@aol.com 
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 Intermittent mic connector

[bill conkling]

First thing I'd do is eliminate all but the mic, cable and K3.  If problem 
persists check plug on cable.  Then at mic end.  Finally check other items one 
at a time.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Mike Sanders k...@centurytel.net wrote:

Greetings All, My K3/10F now K3/100 plus mostly loaded has a problem.
The mic connector has to be pressed down a bit to get PTT when using
the K3 on SSB. I use a Heil PR781 mic that goes through a Rigblaster Duo.
The connector to the K3 comes from the Duo and is never changed or
fooled with. Before I pull the front panel module has anyone had this
same issue and what was the problem? Thanks for any hints/help. 73

 K0AZ
   Mike Sanders
EM37cd SW Missouri
 www.k0az.com







__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3: VFO B Display SHowing ERR KEY

[bill conkling]

You have a hey or paddles plugged in and making contact.  Unplug everything and 
try again. If all is OK, plug stuff in one at a time.

Could also be some software holding key thru a serial port.  Check software 
settings.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Jay j_kris...@msn.com wrote:

Hi all,

 

Switched on my K3 this morning and noticed that the VFO B display was showing 
ERR KEY. Will look into the manual for possible reasons, but appreciate any 
pointers.

 

Thanks,

 

Jay Krishna

KD6AMA
 
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 FM

[bill conkling]

Check CONFIG/BandMap settings for each band you want to use FM.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

István Szabó ha...@t-online.hu wrote:


Just installed the FM filter. Using the latest utility and firmware it is set 
for FM mode. With MODE button I can not select FM mode just with K3_EZ 
program, than it works in FM mode. Am I missing something?

73, István

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Screw Types

[bill conkling]

Tools required are listed in the Assembly Manual.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Richard Solomon w1...@earthlink.net wrote:

I will be getting some new screwdrivers to assemble my K3 kit, but I 
need to
know which type of Phillips Head Screwdiver to buy.

Are the US made or Japanese made ?

Tnx, Dick, W1KSZ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3: Problem with CM-500 plugged into front panel through AD1K

[bill conkling]

The AD1K has a DC blocking cap built in.  Plug it in the rear jack or use the 
battery box provided with the CM500 to provide bias.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Stan Rowe shrt...@chartermi.net wrote:

Does anyone have any ideas why my Yamaha CM-500 microphone won't work when
plugged into the front of the K3.  I am using the Kenwood AD1K adapter and I
have the firmware set to select the front panel, low gain, with bias on
(FP.L bIAS).  The CM-500 headphones are plugged into the Phones jack on the
front of the K3 and work fine.  The CM-500 mic plug (grey) is plugged into
the corresponding jack on the AD1K.   When I press my footswitch, the K3
goes into transmit but there is no audio when I speak into the CM-500's
microphone.  I have tried the footswitch plugged in both on the back of the
K3 and into the AD1K footswitch jack and it works fine (puts the K3 into
transit) in both cases.

 

When plugged into the rear Phone and Mic jacks on the K3, the CM-500 works
like it should.  In that case I have the firmware set to RP.L bIAS.and both
the CM-500 microphone and headphones work fine, so I'm quite sure the CM-500
is not the culprit.

 

It almost seems like the AD1K is the problem.

 

This must be something simple, but I am stuck.  Any suggestions much
appreciated.

Thanks

Stan - K6VWE

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3: Problem with CM-500 plugged into front panel through AD1K

[bill conkling]

Well, I sure thought I read it.

Mind isn't what it used to be.  I'll go back to sleep.

...bc

Sent from my Verizon Wireless 4G LTE DROID

Don Wilhelm w3...@embarqmail.com wrote:

Bill,

Are you certain about that?  Bob Heil has told me in the past that none 
of his adapters have blocking capacitors.

73,
Don W3FPR

On 1/21/2014 7:50 PM, bill conkling wrote:
 The AD1K has a DC blocking cap built in.  Plug it in the rear jack or use 
 the battery box provided with the CM500 to provide bias.

 ...bill nr4c



__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KPA500 Power On

[bill conkling]

Yes I have noticed this.  No idea what brings it on.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Jim Bennett w6...@mac.com wrote:

I recently got a KX3 and have set up my station such that the KX3 can share 
the KPA500, KAT500, and several antennas by using a pretty beefy Daiwa 
2-position coax switch. The station is set up just like the diagram on page 
147 of KE7X's KX3 book. This configuration seems to work very well. However, 
I've recently noticed a very occasional anomaly with the KPA500. Every once in 
a while, I go to power it on and nothing happens. I have to reach around to 
the back panel rocker switch, turn it Off and then back on. Then, the front 
panel power on button brings the amp to life. So far I've not been able to 
track it down to a particular sequence of operating events that precedes it. 
In the past 3-4 days, this has happened maybe three times.

Anyone else have this happen, and if so (1) what causes it, and (2) how to 
resolve it? Not a big deal, but I'd like to know what's going on.

Jim / W6JHB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] How do I generate a Key Down to tune an external 6m amp?

[bill conkling]

You might try the 1/4 inch jack on the back labeled KEY.  I dunno but it 
might work.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Bob KD7YZ kd...@denstarfarm.us wrote:

Willis 'Cookie' said:

 The easy way is to hold the dash on the bug.

unless I am missing something in Setup, I do not see how to tell the K3
that I want manual dashes and string-dots. There is no setup for the
keyer. So obviously if I short out the dash side, of the Vibroplex
paddle, I get dashes. Many of them.

And that is my question. How do I get a solid key-down, where the PTT IS
activated, and RF flows?

Seems right simple ,but my two choices here do not work.
Use the keyer, push the PTT foot-switch, and I get a nice string of dots
or dashes, as all of us expect.

Push/HOLD the XMIT button and the PTT output of the K3 seems to not
engage.

Where, on the K3, would one pug in a regular old straight-key, and
expect it to work as a regular old straight-key?

The answer to that would solve my Sequencer problem for tuning w/o
frying anything in the LNA chain.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] KX3 BOSE speakers...

[bill conkling]

What's the opinion on BOSE COMPANION 2 SERIES III MULTIMEDIA Speakers for use 
with K3 or KX3?

Just ordered from Amazon...

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] KX3- WTB PIGLET

[Bill Conkling]

I am looking for a Pignology PIGLET.  They seem to be out of stock
currently.  If you have one avail email me 'off list' to n...@arrl.net or
n...@widomaker.com

Also looking for tips or assistance in setting this up with Samsung TAB2 and
KX3.  Have HAMLOG already.

Thanks for your consideration.

nr4c  bill

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] KX3/KXPA100-K..#246 ON THE AIR!

[bill conkling]

Well my kit arrived today.  Got it together with little trouble.  My fingers 
don't do well with #4 screws, etc.

First tests were hopeful.  All seemed to be going well.  Cranked up the power 
and this is great.  Except for the different control layout its like a K3 w/one 
RX.   Sig and audio reports were good.

Love it so far.  More to come.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3 copying settings to another

[bill conkling]

Not possible at this time.  The saved file contains all the settings you want 
to configure the radio, but also calibration and other settings that are radio 
specific.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Dominic Baines dominic.bai...@ntlworld.com wrote:

Hi,

Sure this has been answered but cannot seem to find it

I would like the clone one KX3 settings over to another.

The backup/restore is great but will not let you do it as the serial 
numbers are different.

Both are identical EXCEPT one (the one I want to copy to) doesn't have 
the internal ATU.

Is this possible?

It's all the little tweaks and the macros etc I'd like them to exist on 
both. Pain having to adjust all the menus manually.

72

Dom
M1KTA
#1082 and #2334
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3 copying settings to another

[bill conkling]

How would you map the eight cw messages into six on KX3?  Or the 8 DVR msgs 
onto just 3?

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Bill Frantz fra...@pwpconsult.com wrote:

While we're thinking about this subject, consider being able to 
copy the major settings between all Elecraft models (where it 
makes sense). I could see a UI that said, Copy macros, Copy 
memories etc. The user would select which chunks to copy.

Cheers - Bill, AE6JV

On 12/12/13 at 9:49 AM, dominic.bai...@ntlworld.com (Dominic 
Baines) wrote:

So do you know how could it be done? Is it planned? Must be a 
few SO2R K3/KX3 ops out there by now

Any reason why a 100% backup could not be taken? Or is the idea 
that a combination of firmware (MCU and DSP) plus the 
configuration backup is the same as full backup, what else is missing?

---
Bill Frantz| The only thing we have to   | Periwinkle
(408)356-8506  | fear is fear itself. - FDR  | 16345 
Englewood Ave
www.pwpconsult.com | Inaugural address, 3/4/1933  | Los Gatos, 
CA 95032

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] OT: Crimping small wires

[bill conkling]

Crimping the wire over the insulation doesn't seem too good to me.

I have used a dab of hot melt glue to stabilize the wire at the rear of the PP 
Plastic.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

EricJ eric_c...@hotmail.com wrote:

I don't usually do that because the wire exiting the APP barrel is still 
just a small strand that flexes easily and can eventually break. It 
gives you a lot more surface area for crimping, but needs strain relief 
to be secure in the long run.

What I do is strip the wire the same length as normal, then fold it back 
over the insulation. I insert the wire and insulation into the barrel 
with the wire down (away from the split in the barrel), then crimp 
normally. This makes a solid electrical connection with the stiffness of 
the wire insulation which also provides more than adequate strain relief.

I've mentioned it here before and some are aghast, but I have maybe a 
dozen connections like that currently in my shack and not one of them 
has ever failed in the 10 years I've been doing it with APPs. But any 
connection where this is necessary is a low voltage, low current DC 
connection so what's it going to hurt? It isn't any worse electrically 
than using a small wire nut which is considered safe enough even for 
house wiring.

Eric
KE6US



On 12/11/2013 9:41 AM, Edward R Cole wrote:
 A little off topic:

 I wonder if any of you do what I do when using wires are too small for 
 crimp connectors?  I strip twice as much insulation from the end of 
 the wire and then fold the bare wire over double.  May have to squeeze 
 using small nose pliers to get it doubled tight enough to fit inside 
 the crimp connector.  The crimps hold the undersized wire very well 
 with this procedure.

 BTW this works for solid conductor wire, like hookup wire.  Bend the 
 conductor double and there is something for the crimp to hold.

 I do not know if this will work with powerpole connectors.  My problem 
 was having too large diameter wire for the powerpole connectors which 
 inhibited proper crimping; solution chose proper size connector for 
 the wire size selected.

 73, Ed - KL7UW

 -
 Date: Wed, 11 Dec 2013 09:00:11 -0500
 From: Don Wilhelm w3...@embarqmail.com
 To: Charlie T, K3ICH pin...@erols.com, elecraft@mailman.qth.net
 Subject: Re: [Elecraft] K3 Powerpole Replacement
 Message-ID: 52a86feb.2070...@embarqmail.com
 Content-Type: text/plain; charset=ISO-8859-1; format=flowed

 Charlie,

 The PowerWerx crimper is good.  Just be certain to fill the cavity with
 wire - for instance the 30 amp connectors are sized for #12 wire - if
 the wire is smaller, it may be loose, so in addition to filling the
 barrel with as many wire strands as I can, I add some solder for extra
 security.

 73,
 Don W3FPR



 73, Ed - KL7UW
 http://www.kl7uw.com
 dubus...@gmail.com
 Kits made by KL7UW
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html



__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Internal Antenna Tuner and SPE Expert Amplifier Questions

[bill conkling]

With an outboard amp attached you should BYPASS the internal ATU as it is 
looking through the amp and therefore can't help match the ant to the amp.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

pastor...@verizon.net wrote:

Good Morning,
It's Mark Griffin KB3Z. I was looking at an SPE Expert amplifier and I see it 
has an internal antenna tuner which can handle SWR's of up to 4:0. But, I was 
wondering if I connected the output of my K3 to the input of the amplifier and 
then the antenna to the output of the amplifier, If I used the K3 internal 
antenna tuner to decrease the SWR to a reasonable level would this work? I 
don't currently have the internal antenna tuner in the K3. It is perhaps a bad 
question to ask, but I am currently using a Palstar AT2K as my antenna tuner. 
Any help or advice would be greatly appreciated.  Mark Griffin, KB3Z
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 Powerpole Replacement

[Bill Conkling]

If the PP is not correctly assembled, just immobilizing the connection will
not solve the underlying poor connection.  As Don said, they should be
correctly assembled first.  If you still have problems, then immobilizing
the connector may be appropriate.

...bill  nr4c

-Original Message-
From: Rick Bates [mailto:happymooseph...@gmail.com] 
Sent: Sunday, December 08, 2013 10:03 PM
To: vk...@arrl.net; elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 Powerpole Replacement

Rather than all that effort, why not use a screw hole style zip tie to
anchor it to your grounding point on the back of the radio?  That way, if it
gets moved, it pulls on the tie, not the connector.

73 es Happy Christmas,
Rick wa6nhc

-Original Message-
From: Jeff Cochrane

Hi everyone,
Has anyone on the list replaced the Anderson powerpoles on their K3's with  
something else?

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] Yamaha CM500

[bill conkling]

Just plug it in the MIC  PHONES jacks on rear panel.  No adapters needed.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Lee Buller k...@swbell.net wrote:



Does  anyone sell a cable or have the information for connecting a CM500 to a 
K3?  I think an adapter of some sort is in order here.  I was thinking using a 
adapter to 1/4 inch for the headphone partbut I need to make a pig tail 
for the mike.


Lee - K0WA

 
In our day and age it seems that Common Sense is in short supply.  If you 
don't have any Common Sense - get some Common Sense and use it.  If you can't 
find any Common Sense, ask for help from somebody who has some Common Sense.  
Is Common Sense divine?

Common Sense is the image of the Creator expressing revealed truth in my mind. 
-  John W. (Kansas)

Never interfere with anything that isn't bothering you.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KAT500

[bill conkling]

First, chk antenna system.  Shouldn't be that different.

Also, what does KAT500 Utility say about the tune results?

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Jack Satterfield j...@satterfield.org wrote:

I am trying to tune a G5Rv on 4.7xx (MARS freq) best I can get with the
KAT500 is 2.65 swr,  which means cannot use the KPA500.

Using the K3 barefoot with ATU it tunes to 1.0 swr

Why is there such a big difference in performance?

Jack

W4GRJ

 

 

 

 

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] (no subject)

[bill conkling]

You need the SVGA adapter for the P3.  Chk the web site, scroll down the home 
page.

...bc nr4c

Sent from my Verizon Wireless 4G LTE DROID

David Withers drdavewith...@yahoo.com wrote:

This may seem like a dumb question. So be it.  Exactly how do I hook a larger 
screen monitor to my K3/P3 combination?  Dave AB3PL. Thanks
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] KX3 and KPA-500

[bill conkling]

I'm getting about 250 watts with ~7.5 watts drive.  Works great.  However it 
takes more than 10 watts to get good  tune action on the KAT500.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

George Rebong ke6t...@gmail.com wrote:

I would like to try this combination and wonder how many watts will I get out 
in the KPA-500.
Happy Thanks Giving

73
George

Sent from my iPad 3G
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

[Elecraft] (KPA500) 270V ERR

[Bill Conkling]

Just finished my KPA500 last night.  Plugged it in and it lit up.  Hooray!  
Went to bed happy.  Today I pressed the button to get out of standby and
lo and behold, I got a FAULT and the error displayed 270V ERR.  Took side
panel off and checked cables, tap and anything I could see, all ok.  Saftey
switch appears just as in book, and the actuator assembly looks right.

Help!  Please...

...bill nr4c

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] PC laptop for K3/KX3 digital modes

[bill conkling]

I found several Dell refurbished D620's a while back at the local GOODWILL 
store.  New bat, and warranty on HD and computer.  About $225.

Love mine.  Added memory after warranty ran out and also upgraded to larger 
solid state HD.  Used for many club outings, FDs and personal activities.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Don Wilhelm w3...@embarqmail.com wrote:

Dave,

If you are looking for an economy laptop, I would steer you to the 
refurbished IBM laptops.  They are typically priced at $240 and up 
loaded with Windows 7 professional.  See 
http://www-304.ibm.com/shop/americas/webapp/wcs/stores/servlet/default/CategoryDisplay?categoryId=2576396storeId=1catalogId=-840.

I have had good success with the IBM/Lenovo computers - they just keep 
on running, but then I normally use only desktops, the laptop is only 
for infrequent travel purposes.

73,
Don W3FPR

On 11/19/2013 8:23 PM, Dave Moorman wrote:
 Hello, All -

 I’d like to get the K3 and KX3 on HF digital and am wondering if anyone can 
 recommend a reasonably priced PC laptop which would do that.  My experience 
 has been only Macintosh so the PC laptop world is unknown territory.  A 
 decent keyboard and a trackpad are pretty essential, but that’s about the 
 only hard-and-fast requirements.

 Another question; I have an older iBook G3 on which I’m attempting to 
 install Linux.  Has anyone done that?

 Thanks,

 Dave  K9SW
 __
 Elecraft mailing list
 Home: http://mailman.qth.net/mailman/listinfo/elecraft
 Help: http://mailman.qth.net/mmfaq.htm
 Post: mailto:Elecraft@mailman.qth.net

 This list hosted by: http://www.qsl.net
 Please help support this email list: http://www.qsl.net/donate.html


__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] OT: Checking coax jumpers before soldering

[bill conkling]

I have used 50 ohm BNC 'terminators' with adapter to verify coax.  Start with 
terminator on analyzer, should be flat VSWR over wide band.  When at other end 
of coax should be same.

...bill nr4c


Sent from my Verizon Wireless 4G LTE DROID

Joel Black w4...@charter.net wrote:

Frank,

I use an Anritsu SiteMaster at work to detect such things with hardline 
and coax. It comes with a 50 ohm load for testing feedline. I don't know 
how you'd set up an amateur-style antenna analyzer to do such. When I'm 
looking for faults, I specifically set it to  Return Loss - DTF 
(Distance To Fault).

If you have a station dummy load, you could use that. The one I built 
from Oak Hills Research is a little bulky, but would do the trick I think.

73,
Joel - W4JBB

On 11/12/13, 12:41 AM, Frank Precissi wrote:
 This is along the same lines of the PL-259 connector soldering.  Although
 off topic for this group some collective wisdom might help someone other
 than myself in the future.

 How can you check to see if coax is still good?  Sure we can test for
 shorts with a multimeter, but if the coax has been crushed and the
 dielectric has been deformed, obviously things will be wonky when we put RF
 through it.

 Is it possible to short one connector with a 50ohm resistor, then on the
 other end attaching an antenna analyzer and sweep the ham bands looking for
 obvious SWR changes?  I mean to me (read: newbie when it comes to this) it
 should show a flat 50ohms across the bands, correct?

 I have a few spools of 100' RG8X that I'm sure have been slammed in a
 sliding glass door more than once.  No sign of any trauma on the jacket or
 shorts, but I cant tell if the dielectric has been mangled inside.  I
 really don't want to blindly ditch perfectly good coax.

 Any tricks of the trade when it comes to this?

 73

 Frank
 KG6EYC



__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 CAT-Interface

[bill conkling]

What software?

I use DX Labs and don't have this problem.  I suspect that if I run split, it 
might spot both frequencies.

More info please.

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Karl-Heinz Kuehlborn khkuehlb...@outlook.com wrote:

Hello,

I  have  the problem, that the K3 sends continously the frequencies of
VFO  a  and  VFO  B  (FAxxx,  FB)  out.  This  results,  that  the
Logging-Program always shows me both frequencies.

I  was  looking  around,  how  I  can  have  just  the main VFO in the
seriel-Output, but haven't found it.

Any useful hint for me, to solve the problem.


-- 
vy 73
Karl-Heinz - DL2FAG
mailto:dl2...@arcor.de


---
Diese E-Mail ist frei von Viren und Malware, denn der avast! Antivirus Schutz 
ist aktiv.
http://www.avast.com

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3 - removable face plate

[bill conkling]

You guys do realize this is not a 'removable face-plate', but a very thin K3/0. 
 

...bill nr4c

Sent from my Verizon Wireless 4G LTE DROID

Bill Frantz fra...@pwpconsult.com wrote:

I'm beginning to think about replacing the Icom 706M2G in my 
4Runner. -- Using a K3 has spoiled me. A small operation face 
plate will be a big advantage for any radio that I install. From 
Elecraft I will look at the KX3 and a remote rig K3, but both 
may be larger than the available space in the center console and 
I'm not sure the K3 will fit under the passenger seat.

BTW - I do mostly HF SSB and VHF FM from the 4Runner. As a 
passenger, I could also operate digital. CW is a dream, but my 
first (and currently only) CW QSO was just a couple of weeks ago 
and I definitely need more seasoning. Ten watts on 80M with a 
screwdriver antenna is very marginal, so 100W seems the next step.

Does anyone have any advice?

Cheers - Bill, AE6JV


---
Bill Frantz| gets() remains as a monument | Periwinkle
(408)356-8506  | to C's continuing support of | 16345 
Englewood Ave
www.pwpconsult.com | buffer overruns. | Los Gatos, 
CA 95032

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

Re: [Elecraft] K3/KX3 interface to N1MM logger - WITH DSP digital data ??

[bill conkling]

Yes! But I'm not sure what your DSP DIGITAL DATE is referring to.  I have used 
my K3 AND KX3 with n1mm for RTTY and PSK31.  These are using the computer sound 
card.  I built an interface for my KX3 to include xforner isolation for both 
audio lines and transistor switching for PTT and CW KEYING.  It emulates the K3 
in audio and serial control functions to n1mm.

...bill

Sent from my Verizon Wireless 4G LTE DROID

Steve WB3LGC wb3...@verizon.net wrote:

Has anyone interfaced your K3/KX3 to N1MM logger - WITH DSP data for
PSK/RTTY/CW digital modes???

73, Steve WB3LGC



__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html

__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net

This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html