Hi Robert
This is the article I was looking for
Touch lamp problems
Personally, I think touch lamps are one of the dumber uses of technology
to appear on this planet but that is just my opinion :-).
These are susceptible to damage from voltage surges or just plain old
random
failures. In
Hi
Have a problem with a door that will not lock or latch properly? These
difficulties fall into two general categories: those related to the lock set or
key,
and those related to the door's frame and latch assembly.
If the lock mechanism is broken
Steps:
1.
If the key turns but does not
Hi
Has it been more than a month since you ventured into your furnace's filter
area? Then it's probably time to clean or replace this dust and dirt catcher
to prevent you from sneezing your way into winter mornings. A clean filter
maximizes your furnace's efficiency and longevity-- and minimizes
Hi
When a window air conditioner cools poorly, it doesn't necessarily mean you're
in for an expensive trip to the repair shop. It could be the machine just
needs a good cleaning and some tender care.
Steps:
1.
Remove the front grill. Pry it off with a putty knife if it's held by clips, or
Hi
The next time someone turns on the hair dryer, microwave and toaster oven all
at once and sends your house's circuits into a tizzy, be prepared. If you
live in an older home with electrical circuits protected by fuses, keep
replacements on hand.
Identify and test a blown fuse
Steps:
Hi
You can make an inexpensive anti-fog glass spray to keep your bathroom mirrors
and the inside of your car's windshield fog-free. This solution keeps
condensation
from collecting on these surfaces.
Steps:
1.
Pour 2 ounces of white vinegar in a medium sized bowl.
2.
Add 1 quart hot
Hi Betsy
I would say it is but I will check and see.
Always follow your water heater instructions for your particular Brand
as I do not have a Gas Water Heater.
Lets here for those who do.
Regards
Ray
-Original Message-
From: blindhandyman@yahoogroups.com
[mailto:[EMAIL PROTECTED] On
Hi Max
I thought it seemed wrong.
The Earth prong out here is flat but wider than the others but this is
on a 15 amp outlet.
-Original Message-
From: blindhandyman@yahoogroups.com
[mailto:[EMAIL PROTECTED] On Behalf Of Max Robinson
Sent: Monday, August 07, 2006 2:31 PM
To:
Hi
Measuring your roof's pitch isn't as daunting as you might think. The pitch, or
slope, of a roof is expressed as the distance a roof rises vertically over
a 12-inch horizontal distance. So a roof that rises 6 inches vertically for
every 12 inches horizontally has a 6/12 pitch.
Steps:
1.
Hi
When is a hang-up good? When it's a secure rod or pole to hang your clothes on.
Here's how to make sure those clothes and what they're hanging from stay
put.
Steps:
1.
Decide how much weight you'll need this closet rod to support. Your choices may
be anything from a simple tension rod for
Hi
Constructing a deck will be much easier once you are familiar with the correct
terms for the various elements of a deck. Though there are some differences
between attached decks and freestanding decks, for the most part the following
elements remain the same.
Steps:
1.
Concrete support
Hi Jewel
Can you tell me is this is a Chain Saw or a Table Saw.
-Original Message-
From: blindhandyman@yahoogroups.com
[mailto:[EMAIL PROTECTED] On Behalf Of Jewel Blanch
Sent: Tuesday, 8 August 2006 12:47
To: blindhandyman@yahoogroups.com
Subject: [BlindHandyMan] Skill Saw
Tell me:
Hi
There are two types of sensors designed to detect motion in a room of a home -
a passive infrared sensor (PIR) and a dual-technology sensor, which includes
passive infrared and microwave. Budget considerations will influence your
choice.
Selecting the Sensor
Steps:
1.
Survey your home
Hi
It's easy to add a new style of trim to a door. The job won't take long once
you get the hang of it.
Getting Ready
Steps:
1.
Choose the style of door trim - there are many available. Check photos from the
Internet or magazines, or at home improvement centers and lumberyards (the
best
Hi
To put the finishing touches on interior window trim, you need only a few tools
- but also a plan. There are several styles to pick from; we'll take a look
at the most popular.
Getting Ready
Steps:
1.
Choose the style of window trim - there are many available. Check photos from
the
Hi
It's bound to happen eventually: If you work with tools long enough, they will
break, especially if you push them to the limit. Broken handles on shovels,
rakes and hoes are easy to replace.
Steps:
1.
Purchase a new hardwood handle to replace the broken one. Ash is a very strong
and
Hi
Anyone who lives in snow country knows that the snowblower is one of the most
time- (and back-) saving inventions of all time.
Steps:
1.
Decide which of the two types of snowblowers you need. A single-stage blower
whirls the auger at high speed. A two-stage blower with a slower-moving
Hi
Fertilizing or applying pesticides can be done with a pressurized sprayer.
Sprayers come in either plastic or metal, and in a wide range of sizes; some
backpack sprayers have a pump handle so you can keep up the pressure inside the
tank without having to take off the backpack. Here's how to
Hi
Choosing the right lawn mower can simplify lawn mowing and keep the grass
looking healthy. Compare features and cost, but also be sure you understand what
type of mower is best for your yard.
Steps:
1.
Compare weight, power, cost, safety features, ease of starting, handling and
Hi
Choosing the ideal place for a swimming pool or vegetable garden requires an
understanding of your property's solar orientation ' you'll need to know where
the shade and sun will be all year.
Steps:
1.
Observe the shadow cast by your house and other significant structures on the
property
Hi
Pressure washing is a great way to clean the grunge and grime from concrete
driveways, pathways and patios. By using a pressure washer properly, you'll
eliminate ugly oil stains and the danger that someone will slip on slick dirt
or muck.
Steps:
1.
Assess your project and develop a plan
Hi Max
I will correct this tonight and resend.
Thanks
Ray
-Original Message-
From: blindhandyman@yahoogroups.com
[mailto:[EMAIL PROTECTED] On Behalf Of Max Robinson
Sent: Saturday, August 12, 2006 1:28 PM
To: blindhandyman@yahoogroups.com
Subject: Re: [BlindHandyMan] How to Buy a
Hi
After you set the posts in place, you are ready to install the beam. The beam
runs parallel to the ledger board to hold the joists in place.
Steps:
1.
Buy or build a beam of length suitable to the width to be spanned. 2-by-4s can
be nailed together with plywood spaces to make the width of
Hi
Joist hangers, metal fasteners that attach joists to ledger boards, are
inexpensive and can save you time when you're building your deck.
Steps:
1.
Mark where each joist will be placed on the ledger board, starting at the
outside corner. (Joists should be spaced on 16-inch
Hi
Compost is nothing more than decomposed plant material, so you don't need a
fancy bin to make your own compost. You can create compost in a heap on the
ground, but most gardeners think that containing your compost pile makes it
look tidier. Here's how to make compost in a recycled garbage
Hi
If you cut Styrofoam incorrectly, the plastic foam may crumble or break in the
wrong spots. Try these cutting methods the next time you work with a piece
of Styrofoam.
Steps:
1.
Use a waxed serrated knife, saw, floral knife or other craft knife to cut
Styrofoam sheets and shapes. Draw the
Hi
GMC LSTSAW Laser Tile Cutting Saw
Review
So you've made more than a hundred woodworking projects, spent endless
hours in the workshop, and now its time to renovate the bathroom,
kitchen or laundry
area and your significant other wants you to do it!
Tiling may not be your specialty, but if you
cream bucket?
Sheila
-Original Message-
From: blindhandyman@yahoogroups.com
[mailto:[EMAIL PROTECTED]
On Behalf Of Boyce, Ray
Sent: Tuesday, August 15, 2006 4:09 PM
To: blindhandyman@yahoogroups.com
Subject: [BlindHandyMan] How to Make a Compost Bin from a Garbage Can
Hi
Compost is nothing
Hi
A bowling ball is a very sturdy item and, with simple care, it can last you for
a lifetime. Upgrade your ball as technology improves them, or as your technique
necessitates it.
Steps:
1.
Store and transport your ball in a proper bowling ball bag.
2.
Avoid dropping your ball (mostly for
Hi
Manure tea works like a power shake for plants, helping them grow stronger and
more productive and, evidence suggests, holding diseases at bay. It's a snap
to make. And not to worry: if you use well-cured manure there's no unpleasant
odor.
Steps:
1.
Fill a metal bucket one-third full of
Hi
Extensive remodeling of a dwelling can be costly, but a few simple steps and
modifications can economically enhance wheelchair accessibility.
Indoors
Steps:
1.
Remove loose carpets or rugs.
2.
Change doorknobs to lever-type handles.
3.
Replace narrow doors with pocket
Crash! Your heirloom vase just took a dive and is now resting in pieces. The
end. Or is it just the beginning? With a folk craft known as pique assiette,
or shard art, you can give the pieces new life as a mosaic picture frame,
flowerpot, tabletop or whatever you can dream up.
Steps:
1.
Hi
Spending a little time each fall performing some maintenance and repair--along
with a good cleaning--will keep your chairs looking good for years to come.
Installing a vinyl chair strap
Steps:
1.
Turn the chair upside down. If the damaged straps are held on by metal screws,
remove the
Hi
A roller consists of a handle, a cage and a roller cover, also known as a
sleeve. Here's how to pick a quality paint roller for the job.
Steps:
1.
Choose a handle made of steel and equipped with a plastic grip that is threaded
to accommodate an extension pole.
2.
Be sure the cage
Hi
Treat a leaking roof as an emergency, because it can wreak havoc in your house
in a very short time. Attend to any signs of a roof leak, such as water entry,
stains or mold, immediately to limit damage. Locate the leak from inside and
then take steps to control the damage until you can have a
Hi
Maintaining your pool is easiest when your chemical treatment program and your
filtration system work together. Here are the basics.
Maintaining Your Pool
Steps:
1.
Sanitize your pool with a stabilized chlorine product to provide protection
against bacteria,
These generally come in
Hi
By selecting the rights plants in the landscape near your swimming pool, you
will assure safety for pool users and minimize pool maintenance. Here are some
tips.
Steps:
1.
Consider container plants, which are easy to tend, replace and rearrange. One
additional advantage: Frost-sensitive
Hi
There are 3 Reviews here so please Read to the End
While the engineering behind the design of the Hitachi C 12RSH was undoubtedly
challenging, the result for the user is surprisingly simple. All SCMS have
a knob that locks the saw's power head on its guide rails. The Hitachi C 12RSH
has a
Cleaning Oil Spots from a Driveway or Garage floor
A big oil spot in the middle of your driveway can make the most meticulously
maintained home look dingy. Whether a leak from your car or someone else's
created that mark on your concrete driveway, garage floor or sidewalk, it can
all be
Hi
Once installed, a shower door requires little maintenance other than
frequent cleaning and occasionally tightening a screw. You can easily
take care of the few problems that may arise.
Cleaning a shower door
Steps:
1.
To minimize soap-scum buildup, use a squeegee after you shower to
Hi
When it is time to replace your factory shocks, you may want to consider
replacing the stock shock absorbers with sport or adjustable shock absorbers.
Steps:
1.
Consider how your car rides. If you have worn-out shocks, your car will
experience the following: excessive rebound or float,
Hi Dan
Put a Weed Mat under your Deck
Regards
Ray
-Original Message-
From: blindhandyman@yahoogroups.com
[mailto:[EMAIL PROTECTED] On Behalf Of Dan Rossi
Sent: Monday, August 28, 2006 12:22 PM
To: blindhandyman@yahoogroups.com
Subject: Re: [BlindHandyMan] Weed Killers
So, what do I use
Hi
I bought the 300dd you do not need sight because the set up arms grab
the drill in the set up port and as long as you have the drill pushed in
and turn it to lock then it is in the correct position to tighten the
chuck before removing
You then put it into the cutting port and turn it to the
Hi Dale
I am going to sharpen my masonry bits later on today I will let you know
whether it is successful or I have destroyed my machine.
There is one in particular needs my attention because it hit some
reinforcing mesh in the cement when I was locking down the frame I made
for my air
Hi Don
Sure will let you know how it goes, he wants all the old rails for fire
wood for next Winter that saves me cutting them up and dumping them.
I bought 2,000 tex screws will not need all of these but I have a
project in mind and the left over screws will come in handy for this,
With my tex
Hi Lee
I think I might train one of these bloody kangaroos as a Handy Man
Helper for they have a Pouch where you could keep tools and screws
while doing your handy man jobs .
They move so quickly that you could say hop back to my shed and get me
the saw etc
The only thing is if you upset them
Hi Victor
Generally you carry items in Case something happens.
You may never need anything at all.
But they are there as a safe guard.
For example when we went to Queensland between Towns there was nothing
for sometimes 600 to 700 kilometres if you had a problem out there then
if you did not
Hi Cy
Very good advice the preparation before a trip is crucial, for as much
trouble free motoring as possible and having spares on hand helps.
Regards
Ray
-Original Message-
From: blindhandyman@yahoogroups.com
[mailto:[EMAIL PROTECTED] On Behalf Of Cy Selfridge
Sent: Thursday,
Hi
An uninterruptible power supply (UPS) is the most effective way to protect your
computer hardware and documents from power fluctuations. It also lets you
continue to work during brief power failures.
Steps:
1.
If you have a limited budget, choose a standby (also called off-line) UPS
that
Hi
Check this Web Site Out
http://www.maxiaids.com/store/prodList.asp?idstore=1idcategory=82categ
ory=Braille_WatchescurPage=3sortField=dateAdded+DESC
-Original Message-
From: blindhandyman@yahoogroups.com
[mailto:[EMAIL PROTECTED] On Behalf Of jeremy
Sent: Wednesday, 13 September 2006
Hi
EXPANSION - CONTRACTION JOINT FILLERS
ASPHALT, FIBRE, CERAMAR FLEXIBLE FOAM, SPONGE RUBBER,
CORK and SELF-EXPANDING CORK
MINIMIZE STRESS DAMAGE AND ENHANCE THE PERFORMANCE CAPABILITIES OF CONCRETE
WITH PROPER JOINTING TECHINQUES TO ACCOMODATE EXPANSION-CONTRACTION CYCLES.
Concrete expands
Hi
CRACKING CHECKLIST
If a crack appears overnight in your previously intact brick house,
don't panic. It is not the first step in the total disintegration of
your whole home.
Most cracks require cosmetic treatment only. The majority are not
indications of grave structural damage. Remedies can
Hi
How to Buy a Chain Saw
If you own land, a chain saw can be a great time and money saver. Instead of
using an ax or calling in a landscaper to remove broken tree limbs, bring down
dead trees, or cut firewood -- you can do it yourself.
If you need a chain saw only once, consider a rental. Most
Hi
How to Choose the Right Hinge
A hinge consists of two wings held together with a pin called a pivot pin. Some
are made for either right- or left-handed openings, while others are
specifically
for one or the other. Hinges can be recessed by sinking them in a mortise.
Steps:
1.
Choose a
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]
Sent: Tuesday, 26 September 2006 01:17
To: Boyce, Ray
Subject: Canadian Home Workshop Newsletter - September 2006
Experiencing difficulties? Try our web based version at
http://www.canadianhomeworkshop.com
Hi Hailley
Now Dogs
Although dogs make great pets, there are many
times when wild populations or dogs left to run loose
can present problems. This article will address some
of these problems and offer solutions to these problems.
The devices listed can be used for both wild dogs,
roaming dogs and
: [BlindHandyMan] Neighbor's Pets
Thanks again..Do I buy some of this stuff at a pet store or hardware
store?
- Original Message -
From: Boyce, Ray [EMAIL PROTECTED]
To: blindhandyman@yahoogroups.com
Sent: Monday, September 25, 2006 8:07 PM
Subject: RE: [BlindHandyMan] Neighbor's Pets
Hi
Hi
FIVE TIPS TO IMPROVE STICK WELDING
Shellfish can make you a better welder. Simply think about CLAMS:
Current setting, Length of arc, Angle of electrode, Manipulation of the
electrode and
Speed of travel. If you're just learning the Stick process, technically
called Shielded Metal Arc Welding,
Hi
UNDERSTANDING THE BASICS OF GREASE
Since lubricating oil can oxidize, so can the base oil in grease. When the
grease oxidizes, it usually darkens; there is a build-up of acidic oxidation
products, just as in other lubrications. These products can have a destructive
effect on the
Hi
Wood-plastic composites, often used for such things as outdoor decking,
are one of the fastest growing components of the wood composites
industry. Some
projections have suggested that these products, which were used for less
than 1 percent of decking in the mid-1990s, may capture 20 percent of
Hi
Wagner MMC220 Digital Moisture Meter
Review
Ever built a project out of wood and found out later that nothing really
stayed square, you found cracks or checks in the timber used or
something badly
warped not long after you completed it?
Perhaps you were using lumber that was too wet, i.e. it
Hi
SECTION 1
This may get a little long, but I want to share with you some of the things I
learned in my locomotive days. I worked with the engineers for Sulzer, a Swiss
manufacturer of diesel engines, with Mobil and with a couple of filter
companies, one of which made most of the house brand
Hi
Some of today's most modern car engines can reach 100,000 miles before
their first scheduled tune-up. Unfortunately, there is no 100,000 mile
miracle
motor oil
to protect them. After a few thousand miles or kilometers of service,
virtually every commercial motor oil becomes contaminated with
Hi
Please see details of this Talking Tape Measure.
Description
A 16 foot standard metal tape measure that announces the measured length
with an accuracy of .06 of an inch. Just turn it on and pull it out to
the length
of the object or distance being measured, and the distance will be
announced
Hi Edward
Answer: Goo Gone works great on removing adhesives left behind by
stickers, store stickers, gum, etc. It is found in Sears Hardware Stores
and other department
stores.
HTH
Ray
**
This message and its attachments may
Hi
Making your own simple and effective products is fun
and economical. We think you will be happily surprised
with the results.
Air Fresheners
Most commercial air fresheners do not freshen the air
at all. Instead, they mask one odor with another, coat
your nasal passages with an undetectable
Hi
Either use a pair of inside callipers and then transfer this measurement
to a pair of outside callipers.
Or place a piece of thin rubber or vinyl over the hole to be measured
and with a ball pane hammer place the ball end over the rubber or vinyl
and hit this with another hammer thus making a
Hi
A successful do-it-yourself project starts with good wood. At first you may
think there's a secret lumberyard code when you confront the many types and
dimensions of wood. But once you take time to learn how the industry assigns
grades and determines sizes, it's easy to choose and order the
Hi
There's staggering variety of ceramic tile available - how do you decide what's
right for you? Here are some guidelines to follow.
Consider Function
Instructions
* STEP 1: Be sure that the tile you're looking at is suitable for your
application. Some rugged tiles can be installed outdoors
Hi Everyone
GMC Hobby Tool Kit
Review
Whether you dabble in woodwork, electronics, home renovation, general craft, or
any other hobby, GMC's Hobby Tool Kit has something you might need. Let's
take a look at the package and discover what it contains and whether it offers
value for money or
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]
Sent: Saturday, November 25, 2006 9:04 AM
To: Boyce, Ray
Subject: Canadian Home Workshop Newsletter - Winter 2006
Experiencing difficulties? Try our web based version at
http://www.canadianhomeworkshop.com
Hi
A clogged gutter is like having no gutter at all. Gutters should be kept
free of leaves and other debris so they don't clog and overflow and
cause damage
to the exterior of your home as well as to the foundation.
To avoid these problems a homeowner must make sure to clean gutters and
Hi
Washer Drive Systems
Belts, Couplers, Clutches
Many domestic clothes washers today still use a drive belt of one type
or another, and these LOOK like common 'V-belts' that can be bought at
any auto-parts
store.
But: They're NOT! Be aware that most of these belts also serve as the
spin
Hi
How to Add Years of Life to Your
Refrigerator's Door Seals
Here's a simple trick that will most likely prevent your ever having to
replace either of your
refrigerator's door seals. It becomes even more valuable if you own one
of the newer models whose seals are no longer attached with
Hi
Yes you will need some sighted help for this.
If you're like me, you have 5 or 6 remote controls that wander
all around your living room. We're even seeing them used
in major appliances, air conditioners being the most common so far.
When one of them stops working, here's a simple way to
Hi
Building: What Is Concrete?
Concrete for building is made by binding together, with cement and water,
particles of fine aggregate and coarse aggregate. Fine aggregate is usually
sand,
the particles of which are less than 3/16 in. diameter, but it may consist of
fine particles of crushed
Hi
Building Plastering - Mixing Surface Preparation
To mix cement plaster, the cement, with or without 10% of lime, should be mixed
thoroughly with sand until the colour is uniform. The water is then added
gradually while mixing continues and until the required consistency is obtained
or until
Hi
Plaster Work - Methods, Materials Techniques
This process and the provision of additives during manufacture, determine the
type and grade of building plaster, which have different setting and hardening
times. Different types and grades are usually sold under brand names. To
ensure that
Hi
In traditional building construction if you built in a climate where the
ground freezes you had to make sure the foundation of the building was
below what
is called the frost line to prevent frost damage to the foundation. In
many climates, this meant building an entire basement under the
Hi
Smith-Kettlewell Soldering Series: Part 7
SK Technical Files
Technical Files
Soldering Series
Smith-Kettlewell
Smith-Kettlewell Soldering Series Part 7
Table of Contents
Soldering I
Soldering II
Soldering III: Tinning Stranded Wire
Soldering IV: Popular RF Connectors
Soldering V: RCA and
Hi Max
The first step in setting up a workshop is establishing your needs. A
suitable location for the workshop
must be determined. Workshops can be located in the home or garage, but
ideally the basement or garage
are very suitable locations. You should plan for future expansion prior
to
Hi
How long does microwave energy hang around?
You have probably been warned by your mother: Wait a few seconds (or minutes)
after the beep for all the microwaves to disappear. There is no scientific
basis for such a recommendation. Once the beep has sounded (or the door has
opened), it is safe.
Hi Dan
Do you mean all the E-mails you send are not really you, and that a
person saying it is you is sending these what a let down.
Ray
From: blindhandyman@yahoogroups.com
[mailto:[EMAIL PROTECTED] On Behalf Of Jewel Blanch
Sent: Tuesday,
Hi All
Triton (TBD1500) Belt and Disc Sander
Review
The Triton company has always been known as a company which produces
quality and innovative tools. When the company came under the grasp of
emerging tool
giant, Global Machinery Company, many woodworkers wondered whether the
Triton name and
Hi
French Polishing is the name given to the process
of coating wood with a solution of shellac
dissolved in alcohol, using a rubber made of rag
and cotton wool instead of with a brush. The
alcohol evaporates, leaving the shellac deposited
upon the wood. When applied correctly it
Hi
Rubbing Out A Finish
What makes the difference between a good finish and a great finish?
Rubbing out the finish. From the second you start rubbing the finish,
you start to improve
the surface tremendously.
The main objectives are to remove any small dust nibs that have gotten
trapped in the
Hi
Well it would depend on what you are trying to screw together but here
is a screw guide taken off our Blind Handy Man Files area.
Screw Comparison Guide.
Use this Screw Comparison Chart to help choose the right screw that best
fits your application. Compare Screw Heads, Screw Threads and
Hi Geoff
Thank you for the complement I do go to a lot of trouble in finding
interesting articles and then editing them so they read ok with our
screen readers.
We have on our blind handy man files area thanks to Dave an ever
growing reference library of some interesting articles on many
Hi All
There are some light probes available at Please see url below
The cheapest is about $24
http://www.independentliving.com/searchprods.asp
**
This message and its attachments may contain legally
privileged or confidential
Hi
Prevent Home Electrical Fires
Electrical problems are the cause of more than 40,000 home fires in the
United States each year. On average, these fires claim close to 350
lives, injure
1,400 and result in $700 million in damages according to the U.S.
Consumer Product Safety Commission. Arc
Hi All
Working with Copper Pipe
It's probably safe to say that copper water lines are in the majority of
American homes and for good reasons. Copper is relatively easy to work
with, it
is accepted by plumbing codes, does not impart any objectionable odors
or flavors to water, and it resists
Hi Everyone
Working with Steel Pipe
Chances are if your home is more than 30 years old, you have some steel
piping. This steel piping may be for plumbing supply lines or a gas
piping system.
The material of choice for plumbing these days, however, is plastic or
copper. Copper, either rigid or
Hi All
Plastic-Composite
One alternative, plastic-composite trim, is manufactured from a
combination of recycled wood fiber and plastic. A variety of plastics
can be used, such
as high-density polyethylene, polyvinyl chloride (PVC) and styrene. The
use of wood fiber reduces the cost of the
Hi
Hammer drills are the most popular homeowner products for light-duty
masonry work and occasional concrete work.
Hammer Drills
These days hammer drills are available in both the corded and the more
convenient cordless models. Some are dedicated hammer drills; some are
rotary drill/drivers
with
Hi All
Twist Drill Bits
Twist drill bits are some of the most common shop tools. They're
available in a wide range of sizes, point and twist shapes, and these
days they're not
only available in standard industrial-grade steel, but also in exotic
materials including titanium coated, black oxide
Hi
13 Pro Tips for Crown Molding and Trim
1. Make sure that each length of crown molding you purchase has the exact same
spring angle, width and thickness. Why? Building supply stores purchase their
crown (and trim) from several manufactures, each using their on different
fabrication
Hi
A Good Look at Greenhouses
A greenhouse means the gardening season doesn't have to end with the onset of
winter. It provides a light-friendly location for growing flowers, vegetables
or other plants. Enjoy plump, juicy tomatoes in winter and decorate your home
with tropical flowers
Hi
A bit of discussion recently on removing Rivets here is a Rivet
removing Tool
RIVET REMOVAL TOOL
This quality tool enables the user to quickly and accurately remove
rivets and blind fasteners. Comes complete with drill bits and guides,
#40, #30, #21,
#10. Made in U.S.A.
If you are interested
Hi All
Installing wall tile is basically the same procedure as installing floor
tile. And it offers the same advantages: flexibility of design; a wide
range of
colors, materials and patterns; and if installed correctly, years of
durability. Ceramic or porcelain tile makes an attractive backsplash
Hi Everyone
Understanding water properties all started a little more than 300 years
ago with an Irish chemist named Robert Boyle. He figured out that water
couldn't
easily be compressed. In fact, it's virtually impossible. He found that
when pressure was applied to liquid in a closed system (no
1 - 100 of 448 matches
Mail list logo