This symptom makes me think of edge connector problems I have heard about. But
in my case there are no low voltage errors that seems to be the case in other
reports.
If I cycle the radio off and back on everything is good. I think this is the
third time this has happened, all in the last
I notice on MARS frequencies (slightly outside ham bands) that my power output
starts out low and builds to full output over 10-20 seconds of transmit. The
symptom is easily observed during an MT63 transmission and receiving stations
comment that my signal starts out light and builds to a
Is there a way for FLDIGI to mute the front panel mic input with transmitting
digital modes?
I use FLDIGI 3.21.77 with SignaLink USB, mostly for MT63 MARS work.
The SLUSB is connected to the Line In on the back panel. It all works well
except.
While transmitting MT63 the mic remains open,
Working very well at my station. All three are acting as one and the KAT500 is
playing well with my SteppIR.
Great job Elecraft Team,
Thank you!
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
That happened when I tried to plug in the replacement. Slipped left of the
socket in my RigRunner and had to retrieve it with tape.
The original was correctly installed.
On Jan 9, 2014, at 9:46 PM, Richard Fjeld rpfjeld...@gmail.com wrote:
I just wanted to give you a heads-up when
I use a SteppIR, DB42 with 60/80 dipole so I expect my case to be different
than many others. Regardless, I have been exchanging emails with Elecraft
support and thought these two findings might help someone else.
Stumbled on something today that may be at least a partial cause. For a long
I need help sorting out the ClickOnce installation app. I've checked around
Google and see the same issue with ClickOnce but no solution that works for me.
I'm trying to install K3_EZ utility on my Win7 PC with no luck. Consistent
error message is:
Deployment and application do not have
I need help installing K3_EZ. The zipped file I have is titled K3_EZ2007 and
is 6, 618KB in size. I can't remember if I renamed the file to mark a 2007
version or not.
My problem is with the ClickOnce Application Deployment Manifest, which for
me should be renamed ...Applicaiton Denial
When operating I see a big difference between the noise floor and signal
indications between the K3 meter and P3 display.
For instance, on 80 meters tonight I see a noise floor of around S2-3 on the P3
and a signal peaking just over S9.
At the same time the K3 meter is displaying a noise level
Replaced with Elecraft supplied component? Does the volume control the same as
before or is the trim different? Louder, softer?
Was anything besides the pot changed out?
Could a resistor near the pot be failing?
On Sep 11, 2013, at 4:59 AM, peterc281 peterc...@gmail.com wrote:
I know this is
I'm trying out the Data Modem Terminal used by Army Mars. The K3 is not listed
as a pre-configured radio in the drop down menu for RIGS. I expect one of the
Kenwood models might work but not a clue which one.
I'm Navy MARS and don't currently have an Army buddy to ask.
Thanks in advance for
Do others see continual traffic from K3/P3 connections.
I now notice continual flashing green yellow port traffic lights related to
my K3/P3 connections. Before reinstalling all software and devices on a failed
Win7 installation, I remember less frequent flashing. I'm thinking collisions
on
Maybe this reflector has found a mission. Do you still need a mic?
On Aug 20, 2013, at 9:14 PM, Don Wilhelm w3...@embarqmail.com wrote:
To all,
Thank you, the purse has now been fully funded. Thanks to the generosity of
several hams and Elecraft, my expenses have now been covered. That
So the magnetic mount doesn't have an impact on the speaker function on the
headphones? Seems like one strong magnet on the case could have that effect.
God Bless 73!
Jack - WE5ST
From: k...@bellsouth.net k...@bellsouth.net
To: Elecraft@mailman.qth.net;
I opted for an 8 port adapter. I paid more but I'll never run out of ports - I
hope! I'm currently using 3 of the 8 but have used more with different
equipment arrangements. I can assign any com port to any of the 8 RS232 ports
as long as I don't duplicate. I also have a 4 port USB hub and can
73!
Jack - WE5ST
From: Phil Irons ve1...@gmail.com
To: Jack Berry we...@yahoo.com
Sent: Thursday, July 4, 2013 7:24 PM
Subject: Re: [Elecraft] KPA500 - AC hum in the monitor
HI Jack...
First of all, I apologize for the lateness of this reply; I've been out
It's on the order page now. Same price for any of the three pre's including the
old 6 pre, new 10 pre and new combo 6/10 preamp. $159.95 if memory serves.
On Jul 7, 2013, at 5:30 AM, Gary Gregory vk1zzg...@gmail.com wrote:
Wonder when we will see release of an internal 6/10M pre-amp?
73
Hoping you all will have some good ideas on a cure for this problem.
I am hearing AC hum in my monitor headphones - ONLY when transmitting.
The hum comes and goes instantly when the KPA500 is switched on/off. Same with
other headphones. No question it's related to the amp but not necessarily
He's still got a day!
On Jun 27, 2013, at 4:32 PM, Keith-K5ENS ke...@kathyandkeith.mx wrote:
What week was that?
Keith
--
View this message in context:
http://elecraft.365791.n2.nabble.com/6-10m-Preamp-tp7575498p7575933.html
Sent from the Elecraft mailing list archive at
Same for my KPA-500.
I haven't studied the sequence of how I shut it and the K3 down but have always
assumed that sequence is involved.
This is not unlike the earlier issue of bringing the K3 and KPA500 online out
of order and seeing the amp fail to operate.
On Jun 26, 2013, at 5:53 AM,
Looks like this team is on to something. I checked it out and like the features
but of course the big deal is being able to control all the K-Line without out
shutting down a logging program. I found the response pretty sluggish; I ran it
on a Win7 quad Intel Dell laptop with no other programs
Gary, anything shared with you?
On Jun 10, 2013, at 1:44 PM, Gary Gregory vk1zzg...@gmail.com wrote:
I understand the sensor port is for an inline sensor to allow the P3 to
monitor the TX signal from the K3. A long time waiting for the release of
this has not dampened my enthusiasm but the
My kit built hums but only periodically - more like a cycle and certainly not a
continuous hum. When it happens I can fear it if the room is quiet. Capacitor
recharging?
On Jun 11, 2013, at 12:13 PM, Stan AE7UT ae7...@gmail.com wrote:
I have a kit-built KPA500 that has the same issue.
It's
It certainly can. I just unlocked my K3 for MARS operation. Gary Surrency
gary@elecraft . com can provide the utility and instructions.
God Bless 73!
Jack - WE5ST
From: Jay pc...@verizon.net
To: elecraft@mailman.qth.net
Sent: Wednesday, May 29, 2013 7:54
You can edit the banner that scrolls by when power is switched on. Use the K3
utility to edit the banner to scroll your call or what ever.
God Bless 73!
Jack - WE5ST
From: Russ Pakulski k9...@bellsouth.net
To: elecraft@mailman.qth.net
Sent: Wednesday, May
What radio are you discussing?
On May 28, 2013, at 6:08 PM, Mike Lichtman tch...@aol.com wrote:
I just loaded the newest 1.50 software and set the mic gain as per
directions at tickling 5 bars. So far, so good. I had the monitor function on
and listened on headphones. When I added
Spoke with Eric earlier today. The 6/10 meter per-amp is under way. He hopes to
have them available in two to three months. I don't have pricing info.
On Fri, 17 May 2013 16:42:01 -0400, Jack Berry we...@yahoo.com
wrote:
Has there been any information of Elecraft producing a 6+10 meter
Has there been any information of Elecraft producing a 6+10 meter ore-amp?
Seems I read a hint in this months ago.
73,
Jack
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
If interested, please see my QTH or eHam ad.
Also selling a 60 ft Glen Martin tower.
God Bless 73!
Jack - WE5ST
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Does anyone have knowledge of any software savvy folks showing interest in
picking up K3_EZ? It's a great utility and would be a shame to see it fade
after N2BC did such a great job. I think anyone who has used it would pay for
an upgrade just to keep it supported for future generations of
I'm just an appliance operator that hates to see a good program fall into
neglect.
On Jan 4, 2013, at 5:59 PM, Ken Nicely k...@nicelyweb.com wrote:
What language is it in and is it built on the .net framework?
Ken (KC) Nicely KE3C
On Fri, Jan 4, 2013 at 5:13 PM, Jack Berry we
I have some recent experience Daniel. Within the last 6 months I installed a
TarHeel screwdriver and FT-450D which is now replaced with a TS-480HX. Do you
plan to add an amplifier?
I found some good help in the web as recommended by other hams I respect. The
sites are:
Does she have a sister?
On Dec 29, 2012, at 8:08 AM, Bill Coleman aa...@arrl.net wrote:
My wife completely surprised me at Christmas by buying me a K3/100. I had
asked for donations toward the K3 fund on my Christmas list. Of course, it
arrived three days late.
I spent about six hours
Ian,
Google didn't find anything on the GEX error when I looked. I searched the
Nabble archives and didn't find it there either.
Elecraft support should have that answer.
This is out of my pay grade but I would suspect the power supply rather than
the radio. I say that because I don't see that
Bet it's the Power Pole connectors, meaning the installation of the connectors.
But if it is the RigRunner, West Mountain will take care of it.
Glad you isolated the problem!
On Dec 24, 2012, at 12:52 PM, Ian Kahn - Ham km4ik@gmail.com wrote:
So, it looks like I tracked down my low
Forgot to mention, absolutely run the calibration again with the correct 13.8V
supply. Then address the power output - if it still exists.
On Dec 24, 2012, at 12:52 PM, Ian Kahn - Ham km4ik@gmail.com wrote:
So, it looks like I tracked down my low output issue. The problem appears to
be
The utility takes care of all that for you. Just click watch.
God Bless 73!
Jack - WE5ST
From: Ian Kahn - Ham km4ik@gmail.com
To: Ron D'Eau Claire r...@cobi.biz
Cc: 'Jack Berry' we...@yahoo.com; elecraft@mailman.qth.net
Sent: Sunday, December 23
Have you run Calibrate Transmitter Gain using the K3 Utility from Elecraft?
Just follow the instructions carefully and it's very simple and fast. There are
two levels to run, 5 and 50 watts if I remember correctly. You will get a
report at the end and can watch the progress on you K3 display.
I use headphones on SSB most of the time through the front PHONES jack. I
have the SPKR+PH option set to 'no'. MCU 4.6 installed.
Not
always, but too often when I have been listening through the speaker and
decide to plug in the headphones I get audio in both headphones and
speaker.
If I go
Gotta like low tech! Works without software and shielded cables.
On Dec 18, 2012, at 7:13 PM, PTA_ABD wb2...@roadrunner.com wrote:
Almost the same problem here. The difference is that toggling SPKR+PH on and
off has no effect. I'm also sure the MCU isn't the reason, as this popped up
well
I picked up a package from West Mountain Radio (I have no connection with them
other than being a customer) and have found it a good solution. It still
required buying a gel cell battery (not AGM).
No leaks, no overcharging, fused power distribution for 8 items I believe. The
whole station
I remember thinking the hiss was annoying when I got my radio. I used the eq to
knock it down.
I upgraded the DSP board within a few months of getting the K3 and now I listen
wide open on the AM filter.
I had forgotten all about the hiss till you posted this thread.
On Nov 24, 2012, at 6:47
I use the ClearSpeech speaker in my mobile operation. Same DSP, just adds an
amplified speaker. It is a good addition for mobile but would not recommend it
for base operation. The DSP seems to add its own noise.
I suspect you have other noise issues if you are distracted by noise on the K3
Good suggestion. Hope it makes on next P3 firmware or utility upgrade.
On Nov 11, 2012, at 9:34 AM, Jim Miller j...@jtmiller.com wrote:
I'd like have function key that does what I find myself doing all the time.
Today's PT0S pileup is an example. It's a monster that extends 10-15Khz
After
Don't have the manual available but if memory is good, instructions are on page
59. It's a simple calibration that I just completed. Use the highest WWV or
other known standard frequency you can receive.
On Nov 9, 2012, at 10:21 AM, Adriano Perazio adriano.pera...@uol.com.br
wrote:
Hello
From: Keith Heimbold ag...@hotmail.com
To: Jack Berry we...@yahoo.com
Sent: Wednesday, November 7, 2012 9:22 AM
Subject: Re: [Elecraft] Small HF amp suggestions
Tokyo high power sells the following amp. It is expensive but has good power
output and is highly rated on eham. The only issue
Thanks for the responses.
Looks like RM Italy is an option for mobiling with the KX3 and a mid range
power boost. All others seem to weigh in too heavily in power and cost. Unless
a KPA100 is available sooner than expected, will either delay the KX3 or pick
up the RM Italy.
On Nov 6, 2012,
Is anyone using the KX3 mobile with a small amp? I'm interested to know what
amps are suitable for a 10 watt input / 100 watts out.
I know Elecraft is planning to offer a KPA100 amp in the future but would like
to make the switch on mobile operation now.
Thanks!
God Bless 73!
Jack - WE5ST
I checked out the link and the Radiosport looks like the David Clarke aviation
sets - mic and head phones. Is it just as heavy and clamp as tightly?
73,
Jack
From: W0FK llader...@earthlink.net
To: elecraft@mailman.qth.net
Sent: Tuesday, October 30, 2012 7:55
I have been chasing the poor BNC cable issue as well. I have been using the
DeoxIT-D100L product that many suggested. I thought for a while that it was
fixed but the problem has returned inspite of several applications and attempts
to clean both male female connectors.
God Bless 73!Jack -
Peter,
Check the MON volume. If it's up you'll hear it when transmitting. Just turn it
down to zero.
From: Peter Reinzuch ve7...@gmail.com
To: elecraft@mailman.qth.net
Sent: Saturday, October 27, 2012 9:23 AM
Subject: [Elecraft] audio feed back
I am
My theory on the Peculiar behavior issue:
I have seen this problem several times before and finally decided it's an issue
of interrupted handshaking between the K3 and KPA500. Seems that all
communicating digital devices go through and introduction to confirm
communication before they get down
I asked about 2 weeks ago and Lisa said they are building inventory before
listing it on the order form. It is a 10 meter preamp, similar to the PR-6.
God Bless 73!Jack - WE5ST
From: N5GE li...@n5ge.com
To: Nand Kishore vu2...@gmail.com
Cc: elecraft
yes there is
God Bless Best 73!
Jack - WE5ST
From: Bill b...@w2blc.net
To: elecraft@mailman.qth.net
Sent: Friday, October 12, 2012 8:03 AM
Subject: [Elecraft] K3 ATT switch question
Is there a faintly audible click when the ATT in engaged or disengaged -
Thanks to everyone who responded! I'm glad I asked the question, I don't
remember seeing this topic covered in the last year, may be wrong, but I sure
learned some great techniques.
Got it all working, checking one technique against the other including using
CW/CW reverse and Auto spot as in
No, I'm set flat in rx eq. Was easy to zero beat using 20mHz WWV and the
procedure.
Thanks!
On Oct 5, 2012, at 10:44 AM, Eric Swartz WA6HHQ - Elecraft e...@elecraft.com
wrote:
Is your RX EQ set to roll off lower freqs? The 1-5 Hz zero beat note is
easily heard when listening to the WWV
I have s/n 3012, factory built. On a few occassions I have been told by a QSO
partner that I am tuned a bit high. It has happened infrequently but I decided
to check against WWV.
Three questions:
1) is comparing to WWV a good method to confirm display accuracy? I used my P3
display to center
Thanks Don! Don't know how I missed that but I did.
God Bless Best 73!
Jack - WE5ST
From: Don Wilhelm w3...@embarqmail.com
To: Jack Berry we...@yahoo.com
Cc: elecraft@mailman.qth.net elecraft@mailman.qth.net
Sent: Thursday, October 4, 2012 9:31 PM
Subject
I have a Mac Mini as well as a Win7 Dell laptop. The Dell is the ham machine
but the Mac could easily fill the bill using Windows 7. I boot it directly to
Win7 and no problems.
If you are used to a desktop with serial ports you will need to get a good
USB/RS232 multi port. There are some good
When you say flat display, do you mean no grass? Just a flat line?
Thanks!
Jack
On Aug 20, 2012, at 1:30 PM, k1tm k...@yahoo.com wrote:
rowland wrote
On my P3 the BNC connector problem caused signals to be presented on the
P3 display
that could not have been present at the antenna. The
Yamaha CM-500 is one that gets rave reviews here but it's not my favorite mic.
I just don't use the back input.
On Aug 13, 2012, at 1:50 PM, paul ecker ecke...@yahoo.com wrote:
I am somewhat new to list and definitely a new K3 owner just having completed
the build of #6663. I understand
With the widest filter first,
FL1 = 2.8 kHz
FL2 = 2.1 kHz
FL3 = 1.8 kHz
FL4 = 400 Hz
FL5 = 250 Hz
If you have trouble setting them in this order, let us know. Happy to help.
73,
Jack - WE5ST
On Aug 7, 2012, at 7:33 PM, Alfredo Vélez WP3C w...@aol.com wrote:
Hi everyone
I need some help
As you said below Bill, the reviews and instance of repair reports were good
enough to convince you that the K3 was a good choice.
It would be great if yours had zero problems, of course.
Elecraft support will get it fixed in a manner you are happy with I'm sure.
While you are waiting, don't be
Jim,
you can adjust the volumes independently on the front panel. But you probably
knew that.
Seems also that there is a config setting that needs to be adjusted for the
volume ratio to work correctly - page 37 of the manual.
On Aug 2, 2012, at 10:56 PM, Jim Bennett w6...@mac.com wrote:
I
ended
up with fairly high gain in the P3, and quite a few anomalous blips and
such. Doing the mod got the gain back to normal and all is well.
73
Fred K6DGW
On 8/1/2012 3:08 AM, Jack Berry wrote:
I saw this for the first time a few weeks ago. Check your BNC connections -
just open
I saw this for the first time a few weeks ago. Check your BNC connections -
just open and close the twist on connector, maybe even pull is off and
reinsert. That killed my birdies. It's happened a few times.
Whether or not this is a common problem, I don't know.
God Bless Best 73!
Jack -
Looking for help with KPA500 to Yaesu cabling.
I just got an FT-450D and need to cable it for use as a backup if the K3 needs
to come out of the lineup.
The linear connector on the Yaesu is a 10 pin mini din female. I so far have
not been able to find a source for the male (or female for
UPS is very, very good at their business. Bet you have it tomorrow!
Imagaine how surprised the other person is that they received a radio and not
clothing!
God Bless Best 73!
Jack - WE5ST
From: Fred Smith m...@mo-net.com
To: 'Frode LA2RL'
W2IHY 8 Band EQ can supply bias voltage. There is a simple jumper to place on
the bottom to enable the feature. It certainly has the potential to improve
your xmit audio if set up properly.
On Jul 20, 2012, at 8:31 PM, Roy Morris w4...@carolina.rr.com wrote:
I would like to know if anyone is
Don't know about the PR40 but if it is an electret mic you will need to turn
the bias on. You'll see mic bias in the menus somewhere.
Good luck,
Jack
On Jun 16, 2012, at 8:41 PM, ac8jd ac...@arrl.net wrote:
I am a CW 95% of my operating time. I have the CW side of this rig pretty
down
Market must be off, it took 45 minutes to sell!
73,
Jack - WE5ST
From: N2BC n...@stny.rr.com
To: n...@stny.rr.com; Elecraft elecraft@mailman.qth.net
Sent: Wed, June 13, 2012 9:36:07 AM
Subject: Re: [Elecraft] K3 For Sale (SOLD)
THX to all that replied,
Bill,
Just added an Astron VS-35M to the shack after nearly 20 years with a RS-35m
which is still working like new. I went with the variable supply so I could
dial
up the output voltage to meet charge requirements for a 12V gel cell.
I wouldn't go to any switchers for fixed service if I could
Is anyone using the Byterunner USB Serial Adapters (RS232) in their Elecraft
stations? My interest is in adding RS232 ports to my USB only laptop. The
single
USB adapter from Elecraft is working fine but if I need to speak directly to
any piece of equipment I have to shut down my logging
Just completed my KPA500 kit and in the process I experimented with alternate
button colors. I posted the picture intheElecraft_K3 phot section of Yahoo
groups. Might be useful for anyone is contemplating a change and ordering
buttons. I used Mouser buttons and I had red, white, gray and blue
$650 kit
On May 18, 2012, at 3:52 PM, Bill Hammond wham...@aol.com wrote:
Have they priced it yet? $$?
On May 18, 2012, at 2:35 PM, Phil Hystad wrote:
__
Elecraft mailing list
Home:
The KAT3 is a really good tuner but you won't be running two tuners will you?
On May 13, 2012, at 10:46 PM, Tony BenBrahim tony.benbra...@gmail.com wrote:
Hello,
I am ordering a K3 and was wondering if I need a KAT3, given that I will be
running an auto tuner at the anternna feed point?
Thanks Rick - well done!
From: Rick Stealey rstea...@hotmail.com
To: elecraft@mailman.qth.net
Sent: Thu, April 26, 2012 9:08:33 AM
Subject: [Elecraft] K3 Noise Blanker video
I made a 2 minute video this morning showing how the K3 pulls out a 75 meter AM
QSO
Eric, you know the drill.
How much? When?
From: Eric Swartz - WA6HHQ, Elecraft e...@elecraft.com
To: Elecraft Reflector elecraft@mailman.qth.net
Sent: Tue, April 24, 2012 1:50:57 PM
Subject: [Elecraft] New KAT500 pics from the Visalia DX convention
New
Jim,
When you say it won't install, do you mean it doesn't connect to your K3 or it
won't complete the installation on you computer?
Either way, I'll bet the author can provide some guidance as well as others on
this list.
Bill, N2BC is the author. His email is N2BC (at) stny.rr.com
Good
Lee,
After doing the mod you are contemplating I formulated a new rule for the WE5ST
shack - never touch another SMD. Once I had the mod in place, it wasn't that
big
a difference - not worth the risk to me. My P3 worked fine before the mod and
for the kind of operating I do it was more that
I am using the speakers from West Mountain Radio mentioned several times in
this thread and others regarding speakers. I find they have a nice cut for ham
radio, at least for my ears and setup. Reducing highs are cut nicely and they
have a good response for even dx if I pick up the volume on
Regardless of your budget, Steve, here's a formula that should apply pretty
well. For every $100 you have to spend:
$90 on antenna(s)
$5 on radio
$5 on everything else.
We all make the same mistakes on our first shack. We buy the finest radio we
can
afford (or squeeze into our credit card) and
I hope there is a wish list for the P-3 Utility. It really eases the process of
upgrading firmware, etc.
Please add:
- Save P3 Configuration
- Reload P3 Configuration
This would be the same feature set as in the K3 Utility.
Thanks for the great little utility!
Jack - WE5ST
My K3 was seeing similar SWR with an AL811H. It was intermittent and was
independent of switch position, standby/operate. The antenna is a SteppIR so
SWR was always less than 2:1. With the amp removed the problem is gone.
I don't yet know the cause since the amp is in the shop. It seems likely
2.8, 2.1, 400 - no need to go tighter IMO. Before buying a 1.8, I suggest
spending time on someone's K3 with a 1.8 if you can. I think you would find it
fatiguing to listen to for more than a few minutes. Certainly not a rag chewing
filter.
Jack - WE5ST
On Mar 26, 2012, at 7:48 PM, Dave
You get hooked pretty quickly because it is useful - just had mine a week. I
have used it to more effectively work split dx operations. Seeing where all the
traffic is and where the big signals are in the pileup, I can pick my spot to
make my signal get through. One thing I didn't anticipate is
Well said Tony. Thank you!
Jack - WE5ST
From: Tony Estep estept...@gmail.com
To: Elecraft elecraft@mailman.qth.net
Sent: Tue, March 27, 2012 2:52:36 PM
Subject: [Elecraft] OT -- a lifetime of ham radio
I think of myself as an old-timer, and I suppose that in
Does it accept any commands in the CONFIG menu? Thinking you might be able to
reset one item at a time. Slow but.
Probably by the time you get my message you'll have six other more helpful
responses. This is an amazing group.
Good luck!
Jack - WE5ST
On Mar 23, 2012, at 7:18 PM, Thomas
I had the same problem but didn't seem to be related to changing bands but
happened doing a calibration per page 24 of the manual.
The message said FATAL ERROR, but a reset cleared the error. This happened
twice
during the same operation. Like you, I didn't log the keystrokes leading up to
the
I have just added a P3 panadapter to my station and need to work out the
communication with this new device and the existing ones.
My setup currently works fine with the SteppIR controller tagged into a Y-cable
from SteppIR (RS232/DE-9). The anchor back to the USB hub is the ElecraftUSB
cable
and I didn't have to add a single cable other than the one
supplied with the P3.
It is great to deal with good companies and good support groups like this one.
73,
Jack - WE5ST
From: nr4c n...@widomaker.com
To: Jack Berry jlbe...@yahoo.com
Sent: Wed, March
Thanks Rick! That's the fast tune knob I missed from the TS-850.
Jack - WE5ST
From: Rick Prather k6limae...@gmail.com
To: elecraft@mailman.qth.net
Sent: Sat, March 3, 2012 11:20:57 PM
Subject: Re: [Elecraft] - tuning rate
I wonder how many ops that want a
Kenwood 850 had a good solution - a second, small fast tune knob that could
selectively tune 1 or 10 kHz. Not possible for the K3 but can maybe be on a
'K4' wish list.
It's the only 850 feature that I really miss.
On Mar 3, 2012, at 9:41 AM, Jim McDonald j...@n7us.net wrote:
I would like
Spoke with John yesterday and his signal was clean and strong. Certainly didn't
hear any symptom of rf or a/c hum.
Why not drop him an email?
On Feb 22, 2012, at 6:07 PM, ab2tc ab...@arrl.net wrote:
Hi,
I have heard ON4UN on a number of occations fairly recently and found that
his audio
I have both the printed and electronic versions. Both are terrific resources.
I suspect Fred has a file of lessons learned to incorporate in a new edition
some day.
On Feb 16, 2012, at 11:19 PM, Phil Westover 492comm...@comcast.net wrote:
I HIGHLY recommend this book. It is an excellent way
I'd like to hear that it CAN be fixed. That would be better.
On Feb 15, 2012, at 8:23 AM, briana als...@nc.rr.com wrote:
Alternatively buy any Kenwood, Yeasu et al which has this figured out.
This has been a long standing problem with the K3.
I'd like to hear from Elecraft that it can't be
Wayne,
Define older K3 please. Can you let us know when you started shipping K3's
with gold contacts; date or S/N?
Thanks!
Jack - WE5ST
From: Wayne Burdick n...@elecraft.com
To: Elecraft Reflector elecraft@mailman.qth.net
Cc: elecraft...@yahoogroups.com
Sent:
Oli,
Just started using HRD myself and searching for a solution to the same problem
which I call bouncing band change.
For me, when I change frequencies within the same band HRD works as expected.
It's when using HRD Logbook and I click a DX spot in a different band that the
problem occurs.
Using an ASUS from Newegg with absolutely no problems. I think the model is
VH238 or 238H, manufactured Dec 2010.
From: David Christ radio...@mchsi.com
To: Elecraft@mailman.qth.net
Sent: Fri, February 10, 2012 9:36:58 AM
Subject: [Elecraft] Monitor (OT)
The
I can only guess that the red RCA from your foot switch is dead but you could
determine that with an ohm meter. It should work as described.
KE4D has the more elegant solution, I just migrated all my cables from the old
Kenwood when my K3 arrived and have been too busy operating to integrate
1 - 100 of 126 matches
Mail list logo
