I *think* this may be an issue that your router is not up before LMS
tries to start.
LMS needs to set the time using ntpd. This has been discussed a few
times before.
https://forums.slimdevices.com/showthread.php?109404-ANNOUNCE-piCorePlayer-4-0-0=924768=1#post924=[-4768
Greg Erskine wrote:
> I don't think its normal.
>
> What's different with your setup?
System is a Pi4, Ethernet, WiFi disabled, attached HD with the FLAC
files, powered by the Pi.
Tony
SBTouch SBRadio
Tony T's
I don't think its normal.
What's different with your setup?
Greg Erskine's Profile: http://forums.slimdevices.com/member.php?userid=7403
View this thread: http://forums.slimdevices.com/showthread.php?t=113512
I have a very minor issue that may have started with 7.0, but may also
be a pi4 issue.
If I have a power failure, when power is restored pCp does not start up.
I need to manually reboot the pi4 (by unplugging / replugging the
power) to get pCp to start again.
Anyone else have this occur?
Tony
The squeezelite extension has been updated to v1.9.9.1364 to support the
new Balance control.
The new feature requires LMS 8.2.0-1614413430 from February 27th 2021 or
newer then in the middle of the LMS Player Audio Settings adjust the
Balance slider and click Apply.
33591
Thanks to
Thanks -- last time I tried to get something from the tinycore repo I
had trouble finding a download link. I think I was successful
eventually, though -- oh, I remember, I had to go to a mirror -- I'll
try that. Thanks!
paul (a different one.)
pgf wrote:
> I have a program that I've been running for years on various systems
> which, when built on picoreplayer, surprised me with a segfault. I went
> looking for gdb, and ... was surprised again. :-) Is gdb hidden in
> some unexpected extension?
>
> My system version is:
Man in a van wrote:
> Hi Paul, I don't know if you have seen this
>
> 'https://www.raspberrypi.org/forums/viewtopic.php?f=63=305034
> ' (https://www.raspberrypi.org/forums/viewtopic.php?f=63=305034)
>
> keep safe :)
>
> ronnie
Thanks Ronnie, Ito hard to keep up with rpi.
piCorePlayer a
You can get extra extensions from the piCore repo.
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage: https://www.picoreplayer.org
Please 'donate'
I have a program that I've been running for years on various systems
which, when built on picoreplayer, surprised me with a segfault. I went
looking for gdb, and ... was surprised again. :-) Is gdb hidden in
some unexpected extension?
My system version is: piCorePlayer v7.0.0 | www
paul- wrote:
> The default firmware has not been updated since 9/3/2020. How is that
> continuously? For those that want Beta, its not much effort.
>
> The package is the exact same package that rpi supplies, with
> environment updates needed for pCP, which means you have access to save
>
pgf wrote:
> Thanks. The other part of my question is: does the .filetool.lst file
> get overwritten on an upgrade? I guess I'll find out someday, but
> forewarned is forearmed.
No we dont overwrite that file on upgrade.
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage:
ralphy wrote:
> I'm using a justboom IR remote with pcp 7 64bit.
>
> To clear the keytable the command should be (sudo ir-keytable -p all -c)
> typo?
>
> Then check the output from (sudo ir-keytable -t) again.
>
> Also check the IR values in pcp.cfg (grep ^IR
> /usr/local/etc/pcp/pcp.cfg).
ashceryth wrote:
> Hey guys,
>
> I'm not sure if this is the best thread to post my issue, but maybe
> someone can provide some help. I'm using pCP 7.0.0 (linux
> 5.4.83-pcpCore-v7 | piCore v12.0pCP | Squeezelite v1.9.8-1344-pCP) on a
> RPi 3B+ together with HiFiBerry Digi+ Pro HAT connected
paul- wrote:
> That is the right place to do it. The backup process stores ownership
> in the backup file.and restores ownership during boot.
Thanks. The other part of my question is: does the .filetool.lst file
get overwritten on an upgrade? I guess I'll find out someday, but
pgf wrote:
>
>
> The other issue I have is that when pCP first boots, squeezelite doesn't
> come up -- it fails because hw1mix isn't available. If I simply restart
> squeezelite, it works fine. I'll either figure out a fix, or a
> workaround.
You can likely use a similar approach to this
That is the right place to do it. The backup process stores ownership
in the backup file.and restores ownership during boot.
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage: https://www.picoreplayer.org
Please 'donate'
Hey guys,
I'm not sure if this is the best thread to post my issue, but maybe
someone can provide some help. I'm using pCP 7.0.0 (linux
5.4.83-pcpCore-v7 | piCore v12.0pCP | Squeezelite v1.9.8-1344-pCP) on a
RPi 3B+ together with HiFiBerry Digi+ Pro HAT connected to a FiiO K5 Pro
via Coax.
As mentioned in my previous post, I've modified /opt/.filetool.lst in
order get the contents of /root backed up in mybackup.tgz.
Is this "safe" to do? will .filetool.lst get overwritten during an
upgrade without me knowing about it? If so, is there another way to add
files to the backup?
> On 2/24/2021 1:43 PM, paul- wrote:
> > pgf wrote:
> > [... wants to let two audio sources use pCP's output at a time...]
> >>
> > Squeezelite on pCP directly accesses alsa. Only one process can
> access
> > the alsa device at time, so you will need to do a full pulseaudio
> system
> > to do
diode84 wrote:
> Hello
> Is anyone using an IR remote control with pCP7. I ask as I had it
> running in the past, not sure if it was pCP6, but cannot get any joy
> with pCP7 today.
> The IR transistor is working and connected to +5, 0, and GPIO 22.
> If I clear default keytable (sudo
diode84 wrote:
> Hello
> Is anyone using an IR remote control with pCP7. I ask as I had it
> running in the past, not sure if it was pCP6, but cannot get any joy
> with pCP7 today.
> The IR transistor is working and connected to +5, 0, and GPIO 22.
> If I clear default keytable (sudo
On 2/24/2021 1:43 PM, paul- wrote:
pgf wrote:
I'd like to try an extension that's available for TCL, but not listed as
available for pCP.
Is there a way to configure pCP to access a TCL extension repo?
Specifically, I'd like to install pulseaudio. I currently run about
half a dozen CHIP ("$9
pgf wrote:
> I'd like to try an extension that's available for TCL, but not listed as
> available for pCP.
>
> Is there a way to configure pCP to access a TCL extension repo?
>
> Specifically, I'd like to install pulseaudio. I currently run about
> half a dozen CHIP ("$9 computer") boards
Hi all
I don't know where else to ask this so I hope someone would be kind
enough to help.
I have a RP3 running picoreplayer and want to also run a video server,
VPN etc. So I have installed Dietpi and have everything working in LMS,
Squeezelite as in picoreplayer, but I cannot understand how
diode84 wrote:
> Hello
> Is anyone using an IR remote control with pCP7. I ask as I had it
> running in the past, not sure if it was pCP6, but cannot get any joy
> with pCP7 today.
> The IR transistor is working and connected to +5, 0, and GPIO 22.
> If I clear default keytable (sudo
Hello
Is anyone using an IR remote control with pCP7. I ask as I had it
running in the past, not sure if it was pCP6, but cannot get any joy
with pCP7 today.
The IR transistor is working and connected to +5, 0, and GPIO 22.
If I clear default keytable (sudo ir-keytable -p -all), then test output
>
> However the router will not give it a ip address at all now, so I am
> inclined to think that the hardware is the problem.
I found the SD card slot is sticking and by pressing the card in hard i
can get the picore webpage to work.
SB3, UE Radio, CA DacMagic, Talk Electronic stereo. LMS
I'd like to try an extension that's available for TCL, but not listed as
available for pCP.
Is there a way to configure pCP to access a TCL extension repo?
Specifically, I'd like to install pulseaudio. I currently run about
half a dozen CHIP ("$9 computer") boards around the house -- they run
ralphy wrote:
>
>
> I don't use shairport-sync these days, so I'm inclined to just remove it
> from the next pcp release, unless Mike B decides to fix the included
> tinymdns support.
Please n :)
jasc's
It seems that most squeezelite updates now days need a library update
too. I think I'll remove the simple update option. Doing a full
dependency check, and then reboot is not a big deal.
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage: https://www.picoreplayer.org
Please
Ah - ok - found it. It's Update vs. Full Update.
"Update" of PCP doesn't fix it. There's obviously another dependency -
have to do a "Full Update", which I saw updated some other dependencies
as well - alac and perhaps some others.
After update PCP shows the new version and works fine, but
paul- wrote:
> What's your output device? Change to one of the "hw: xx" outputs.
> That will bypass all of the asound configurations.
Hardware device is hw:CARD=sndrpihifiberry
So, just did a fresh 7.0.0 install and updated squeezelite
piCorePlayer v7.0.0 | www v00011 | linux
What's your output device? Change to one of the "hw: xx" outputs.
That will bypass all of the alsa configurations.
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage: https://www.picoreplayer.org
Please 'donate'
ralphy wrote:
> Is this with or without the alsa equalizer?
>
> I've had several users confirm that the Both Channels (Mono) support
> works, as it does for me.
>
> Did you have the pcp squeezelite v1.9.9-1356 synced with another player?
> That's the only time that LMS enables the Output Left
psketch wrote:
> I just tried the new mono mode with Squeezelite v1.9.9-1356-pCP, pcp
> 7.0.1 and the latest LMS 8.2 nightly, but when I select Mono in the
> Audio settings, I get no output at all. Setting Both or Left I get just
> the left channel as I'd expect. I've taken a default
psketch wrote:
> Hi Ralphy
>
> I just tried the new mono mode with Squeezelite v1.9.9-1356-pCP, pcp
> 7.0.1 and the latest LMS 8.2 nightly, but when I select Mono in the
> Audio settings, I get no output at all. Setting Both or Left I get just
> the left channel as I'd expect. I've taken a
chincheta0815 wrote:
> Hej there,
>
> following my previous posts concerning the visibility of shairport-sync
> I got some feedback from mikebrady the dev of shairport-sync. He says
> that it seems that tinysvcmdns has come to its limits making propagation
> of airplay error prone.
> He asked
Avahi will not be included in the base image, it is a horribly bloated
package. Ralphy maintains shairport-sync for us, if he wants to
transition it back to avahi, I'll leave it up to him.
piCorePlayer a small player for the Raspberry Pi in RAM.
Homepage: https://www.picoreplayer.org
ralphy wrote:
> You should be able to use it with the alsa equalizer, but I haven't
> tried it.
> The mono downmix is performed in squeezelite before sending the audio to
> ALSA.
Hi Ralphy
I just tried the new mono mode with Squeezelite v1.9.9-1356-pCP, pcp
7.0.1 and the latest LMS 8.2
psketch wrote:
> Hi Ralphy - that's nice :-) It's been a asound.conf edit for me always,
> so this will make things easier to maintain. One question (since I know
> this requires careful tweaking of asound.conf) - can you use this
> setting with the equaliser? My single speakers setups are
Greg Erskine wrote:
> Hi chincheta0815,
>
> We haven't done much to shairpoint-sync over the years because we
> recommend you use the LMS plugin instead.
>
> I think this means, you only have to setup once for all your devices.
>
> BTW: You can disable "Broadcast .local" on the [Tweaks] page
Greg Erskine wrote:
> We haven't done much to shairpoint-sync over the years because we
> recommend you use the LMS plugin instead.
>
> I think this means, you only have to setup once for all your devices
Which is nice for some use cases, but also suffers from the drawback
that it doesn't
chincheta0815 wrote:
> Hej there,
>
> following my previous posts concerning the visibility of shairport-sync
> I got some feedback from mikebrady the dev of shairport-sync. He says
> that it seems that tinysvcmdns has come to its limits making propagation
> of airplay error prone.
> He asked
Thanks everyone for your thoughts on this.
The rpi3 uses ethernet cable
Both rpi have different mac addresses
"Can we assume you aren't using any type of access control on your
router that would block an unknown IP address?"
Correct it's a very simple modem/router set up that assigns ip
Hej there,
following my previous posts concerning the visibility of shairport-sync
I got some feedback from mikebrady the dev of shairport-sync. He says
that it seems that tinysvcmdns has come to its limits making propagation
of airplay error prone.
He asked if there is any avahi support on
Can we assume you aren't using any type of access control on your router
that would block an unknown IP address?
Howard
Greg Erskine wrote:
> @Patricia P
>
> I assume you are using ethernet cables. I can't say I have ever seen pCP
> not connecting via DHCP unless I had a faulty cable.
>
>
Patricia P wrote:
> Neither work, i set this up previously so I expect that the problem is
> with some overlap in setting up two pcp rpi on the same LANDo the two pCPs
> have different MAC addresses?
Sent from my Pixel 3a using Tapatalk
@Patricia P
I assume you are using ethernet cables. I can't say I have ever seen pCP
not connecting via DHCP unless I had a faulty cable.
The IP address does sometimes change, which is the only complication I
ever get.
'Determine your piCorePlayer IP address'
ralphy wrote:
> The squeezelite extension has been updated to v1.9.9.1356 to support
> down mixing the L + R channels to MONO and sending the MONO mix to both
> the LEFT and RIGHT speakers.
>
> This will allow you to connect a single speaker to a pCP player on
> either channel for a MONO
Greg Erskine wrote:
> Should be http://ipaddress or hostname.local
Neither work, i set this up previously so I expect that the problem is
with some overlap in setting up two pcp rpi on the same LAN
SB3, UE Radio, CA DacMagic, Talk Electronic stereo. LMS 7.9.1
BBCiPlayer, Shairtunes2 plugins
Should be http://ipaddress or hostname.local
Greg Erskine's Profile: http://forums.slimdevices.com/member.php?userid=7403
View this thread: http://forums.slimdevices.com/showthread.php?t=113512
I have been struggling to install pCP on rpi3b today. The router
initially renamed the original one RPI4 with a new name, and the rpi3
now piCorePlayer and a different ip address. The new instance was
unable to connect due to this.
I renamed the original host name and player name, and
The squeezelite extension has been updated to v1.9.9.1356 to support
down mixing the L + R channels to MONO and sending the MONO mix to both
the LEFT and RIGHT speakers.
This will allow you to connect a single speaker to a pCP player on
either channel for a MONO setup. No more need to modify
dreagle wrote:
> No more justboom hat ?
> Just had to modify manually the config.txt to load the DTB at boot, and
> all works fine...
> But no more access to JustBoom AMP HAT from the pCP WEBUI !
It should be there!
Grumpy Bob wrote:
> I'm using a power off shim but with different GPIO assignments:
>
> 33208
>
> Works fine for me, I've also wired in a separate illuminated momentary
> switch on the case. This is with pCP 7.
>
> Robert
With pCP v7 and my audiophonics raspdac I use this
Poweroff / yes /
No more justboom hat ?
Just had to modify manually the config.txt to load the DTB at boot, and
all works fine...
But no more access to JustBoom AMP HAT from the pCP WEBUI !
dreagle's Profile:
On the latest picoreplayer version with the latest pcp_shairport-sync I
encounter an issue with the service propagation for Airplay:
Right after startup shairport-sync propagates to my iPhone (iOs 14.4). I
can play music a desired.
Then after a while shairport-sync vanishes and does not show up
ralphy wrote:
> The -Airplay is append in /usr/local/etc/init.d/shairport-sync and I
> think it overrides the name setting in the config file.
> For changes to persist in the config file across reboots you need to add
> usr/local/etc/shairport-sync.conf to /opt/.filetool.lst and backup your
>
IanHaynes wrote:
> Not initially. I use WinSCP and it was one of several hidden files. Have
> now added my own presets. Success!
>
> Does the note on the Tweaks page need amending to point at /home/tc ?
>
> Thanks for the pointer.
Good you got it going. There are a few places on the web that
TomS,
That is likely from empty space in the partition having data(from files
that may have since been deleted). The image creation reads the exact
data in each block. So one card had data that could not be easily
compressed.
piCorePlayer a small player for the Raspberry Pi in RAM.
That can also be done on the tweaks page for the equalizer. Whatever
comes easiest :-)
IanHaynes wrote:
> Yes I am using the equalizer in Tweaks, but I wanted to save my own
> presets.
Howard Passman's Profile:
chincheta0815 wrote:
> Would it be possible to add an option (in beat options) to set the name
> of the ShairPort-Sync daeon to a user-defined one?
> Right now there is an "-AIRPLAY" which I would overwrite.
>
> I understand that there might be issues with the SqueezeLite name when
> there is
Greg Erskine wrote:
> Did you find /home/tc/.alsaequal.presets?
Not initially. I use WinSCP and it was one of several hidden files. Have
now added my own presets. Success!
Does the note on the Tweaks page need amending to point at /home/tc ?
Thanks for the pointer.
IAN
*Library*: Netgear
As a numpty, I might suggest it is the difference between armel and
armhf, but I'm just guessing :confused:
https://wiki.debian.org/RaspberryPi
ronnie:)
Man in a van's Profile:
short version: 2 pCP devices, very similar, with very different SD
Image file sizes.
long version:
I have two players, one based on rPi zero-w and one based on rPi 3, both
using hifiberry DACs.They are configured identically - same SD card
size (8 gb), same partition sizes (2 gb for pcp),
Did you find /home/tc/.alsaequal.presets?
Greg Erskine's Profile: http://forums.slimdevices.com/member.php?userid=7403
View this thread: http://forums.slimdevices.com/showthread.php?t=113512
Howard Passman wrote:
> Unless you're using piCorePlayer. Right? Then can't you use the pCP
> Audio Tweak 10 band equalizer?
>
> Howard
Yes I am using the equalizer in Tweaks, but I wanted to save my own
presets.
IAN
*Library*: Netgear NAS Duo
*Server*: RPi3 / PiCorePlayer with LMS 8.0
IanHaynes wrote:
> Excellent, thank you. I misread it and thought that the file already
> existed! Sorry.
Congratulations, there is a hidden file called
/home/tc/.alsaequal.presets, your the first person to ask about it!
Code:
$ cat .alsaequal.presets
RESET="66
Would it be possible to add an option (in beat options) to set the name
of the ShairPort-Sync daeon to a user-defined one?
Right now there is an "-AIRPLAY" which I would overwrite.
I understand that there might be issues with the SqueezeLite name when
there is a shairtunes-bridge running...
Unless you're using piCorePlayer. Right? Then can't you use the pCP
Audio Tweak 10 band equalizer?
Howard
paul- wrote:
> There are presets in our code, if you want to make your own preset, You
> have to create the file /home/tc/alsaequal.presets
>
> The content would look like this. (Its in
paul- wrote:
> There are presets in our code, if you want to make your own preset, You
> have to create the file /home/tc/alsaequal.presets
Excellent, thank you. I misread it and thought that the file already
existed! Sorry.
IAN
*Library*: Netgear NAS Duo
*Server*: RPi3 / PiCorePlayer with
There are presets in our code, if you want to make your own preset, You
have to create the file /home/tc/alsaequal.presets
The content would look like this. (Its in the web interface if you
expand the more> tag)
MYPRESET="66 66 66 66 66 66 66 66 66 66"
The name of the preset is a simple
Can someone tell me where the alsaequal presets are located? The Tweaks
page says it's $HOME/.alsaequal.presets but I don't see anything there.
Ian
IAN
*Library*: Netgear NAS Duo
*Server*: RPi3 / PiCorePlayer with LMS 8.0
*Main System*: RPi2 / iQAudio DAC+ / PiCorePlayer
*Second System*:
Clausi wrote:
> You could have a look at Main Page > Beta functions > Extras > Bootcodes
> > ntpserver=
Great, thank you!
ds720+
raspberry pi 4 modell b 4gb
picoreplayer v7.0.0 64 bit
lms 8.1.x
marc's Profile:
marc wrote:
> Dear experts,
>
> I would appreciate your advice regarding the *system time* of
> piCorePlayer.
> My setup:
> Raspberry Pi 4 Modell B 4GB
> piCorePlayer v7.0.0 64 Bit
> LMS 8.1.x
>
> I noticed that the Squeezebox Classic showed an incorrect time by 2
> minutes. When I
See
https://forums.slimdevices.com/showthread.php?112335-piCorePlayer-6-configuring-NTP-server=982399=1#post982399
Paul Webster
http://dabdig.blogspot.com
author of \"now playing\" plugins covering radio france (fip etc), kcrw,
supla finland, abc australia, cbc/radio-canada and rte ireland
Dear experts,
I would appreciate your advice regarding the *system time* of
piCorePlayer.
My setup:
Raspberry Pi 4 Modell B 4GB
piCorePlayer v7.0.0 64 Bit
LMS 8.1.x
I noticed that the Squeezebox Classic showed an incorrect time by 2
minutes. When I patched the piCorePlayer via the section "pCP
Howard Passman wrote:
> I hate to ask, but have you checked your power supply? I have two
> server/players running all the time at home and one running in the car
> that gets the power pulled every time I shut the car off. All three run
> great. Using pi4, piCorePlayer 7.0.1, the current
coyrls wrote:
> I'd hesitate to give a recommendation. My player only is turned on and
> off at the mains all the time, my LMS and player combined is always on
> and rebooted infrequently. In your position, with only one failure, I
> would forget it for now and pay attention if it happens
slartibartfast wrote:
> Turn it off and on again does fix a lot of issues. I can't remember this
> ever happening before though. It probably had been running for a long
> time. Is it recommended to have a scheduled reboot when pCP is only used
> as a player?
>
> Sent from my Pixel 3a using
@pgf
If you look at it from the configuration file's point of view, it does
overwrite MAC_ADDRESS="" with MAC_ADDRESS="dc:a6:32:cc:bb:aa". :)
I do agree "override" sounds better. I'll update it the next time I
check out the appropriate branch.
Setting the MAC address should be only, what's
coyrls wrote:
> To be clear, I don't think from what you've reported that pcp is
> "crashing", it seems to be that Squeezelite is no longer functioning.
> As has been suggested, if there is a fault with the DAC hardware or the
> DAC driver, this could happen and it may require a reboot before
There's a typo in the help for setting an alternate MAC address for
squeezelite. The term "overwrite" is used -- I'm sure that what was
meant was "override". Clearly this config doesn't actually overwrite a
system MAC address, which would make the option a little scarier than it
actually is.
To be clear, I don't think from what you've reported that pcp is
"crashing", it seems to be that Squeezelite is no longer functioning.
As has been suggested, if there is a fault with the DAC hardware or the
DAC driver, this could happen and it may require a reboot before the
fault can be
Howard Passman wrote:
> Another guess at this could be the network. Are you running it on Wifi?
> If it happens frequently you may try running it over Ethernet for a
> while to see if the behavior goes away. Jivelite will continnue to run
> on the player regardless of whether or not you have a
Another guess at this could be the network. Are you running it on Wifi?
If it happens frequently you may try running it over Ethernet for a
while to see if the behavior goes away. Jivelite will continnue to run
on the player regardless of whether or not you have a network
connection. And if you
Check out if the red LED is blinking. That's the under-voltage warning.
Depending on what else you're powering the official supply may still not
be enough. I always try to use the 5.25volt 3 amp supplies to be sure.
Howard
slartibartfast wrote:
> It is a Pi 3 with the official power supply.
Howard Passman wrote:
> I hate to ask, but have you checked your power supply? I have two
> server/players running all the time at home and one running in the car
> that gets the power pulled every time I shut the car off. All three run
> great. Using pi4, piCorePlayer 7.0.1, the current
I hate to ask, but have you checked your power supply? I have two
server/players running all the time at home and one running in the car
that gets the power pulled every time I shut the car off. All three run
great. Using pi4, piCorePlayer 7.0.1, the current JiveLite and LMS
8.1.2 - 1613284909
Pommes wrote:
> Well, I am using picore 7 on a raspberry 3B and a raspberry 4, both, as
> server and player and it is running rocksolid all day, all night,
> faster and better than ever before. So i guess it is either your
> configuration, or some malfunctioning hardware part.
> I hope you can
Clausi wrote:
> I have those crashes frequently. More or less every day and sometimes a
> few times a day. Sometimes even piCorePlayer is not anymore reachable
> from the web interface. In this case Jivelite is still running and shown
> on the touchscreen which is attached to my Pi. When I then
slartibartfast wrote:
> I just had pCP crash while playing. At least I assume it did as it
> disappeared from my player list. The pCP web page said squeezelite was
> running. Restarting squeezelite didn't work and squeezelite was then
> reported as not running. Only a reboot restored the
Viragored wrote:
> I've had this happen twice, now. Or something similar, anyway. The most
> recent was a few days ago, the previous time around mid-last year. Each
> time LMS just stopped while playing something (the recent stop was while
> streaming BBC Sounds app). The pCP home screen showed
AlecSp wrote:
>
> Depending on where you live, you're either saying that the last update
> was on 9 Mar or on 3 Sep last year - can we be explicit with dates,
> please - about the only way of doing it unambiguously is d Mmm -
> although there's a tidiness to _mm_dd that is obviously
slartibartfast wrote:
> I just had pCP crash while playing. At least I assume it did as it
> disappeared from my player list. The pCP web page said squeezelite was
> running. Restarting squeezelite didn't work and squeezelite was then
> reported as not running. Only a reboot restored the
I just had pCP crash while playing. At least I assume it did as it
disappeared from my player list. The pCP web page said squeezelite was
running. Restarting squeezelite didn't work and squeezelite was then
reported as not running. Only a reboot restored the squeezelite player.
Anyone
AlecSp wrote:
> Two quick points:
>
> I've never been quite clear on firmware updates. Are they rolled into
> piCorePlayer, albeit maybe not on a frequent basis? Or do they need to
> be applied separately at a lower level?
>
> Depending on where you live, you're either saying that the last
Howard Passman wrote:
> I'm under the impression that you can have at least 2 drives for music
> storage. Are there any caveats to that? Can I have 500GB USB drive and a
> 250GB USB drive?
>
> Thanks,
>
> Howard
I have 2 USB SSD drives with music connected via USB-Hub. Each has 1 TB.
This
AlecSp wrote:
> Two quick points:
>
> I've never been quite clear on firmware updates. Are they rolled into
> piCorePlayer, albeit maybe not on a frequent basis? Or do they need to
> be applied separately at a lower level?
>
> Depending on where you live, you're either saying that the last
501 - 600 of 1284 matches
Mail list logo
