Nice done André,
Is Defkalion making some treatment on this foam ? Or is it used as
this ? They said that they modify the usual crystallography face
centered cubic.
Some Oxide they said to use can be easily incorporated inside the foam.
Might worst a try to have the foam and test it.
What is the new method of treatment for the wire?
The new method, although started from the old one in some key aspects, was
really revolutionary about the practical parameters of: mechanical stability
(few leakage of the best material from the surface), percentage of
material at small
Celani has a patent for oxidation of Ni surface :
http://www.google.com/patents?id=0iQSAgAAEBAJzoom=4dq=francesco%20celanip
g=PA1#v=onepageq=francesco%20celanif=false
_
From: Arnaud Kodeck [mailto:arnaud.kod...@lakoco.be]
Sent: mercredi 15 août 2012 12:20
To: vortex-l@eskimo.com
From what I've read, Celani and al have currently made 2 wires only. One of
the wires has blown out during a test with D2.
-Original Message-
From: Akira Shirakawa [mailto:shirakawa.ak...@gmail.com]
Sent: mercredi 15 août 2012 18:16
To: vortex-l@eskimo.com
Subject: Re: [Vo]:Celani device
Hello Chemical Eng,
Ive a little question about your theory: Does your theory explain how NAE
spreads over the lattice once the reaction is triggered? It could be also a
misunderstanding of experimental results.
Another question arises when Im writing this: Does your theory explain the
I think AR is smarter than this.
He said Ni+p - Cu when it knew it was not the case. With this statement, he
was sure that Cu will not be taken as a potential catalyst and only a
by-product.
I think also that Cu isn't the only catalyst for the reaction. There is
still some more to be discovered.
.
-Original Message-
From: Jones Beene [mailto:jone...@pacbell.net]
Sent: vendredi 17 août 2012 17:44
To: vortex-l@eskimo.com
Subject: RE: [Vo]:Stunning slide from Technova
-Original Message-
From: Arnaud Kodeck
With Celani, the experiment shown at ICCF-17 reaches around 3W/cm² which
is
very
Ive a bit concern about the total radiation. But Im not expert in
calorimetry, neither in heat transfer.
Radiation is emission of IR (infrared) from a warm surface. The Boltzmanns
law give the energy radiated from a surface at a given temperature and kind
of material.
Inside the
from Technova
At 10:30 AM 8/17/2012, Arnaud Kodeck wrote:
I think AR is smarter than this.
He said Ni+p - Cu when it knew it was not the case. With this statement,
he
was sure that Cu will not be taken as a potential catalyst and only a
by-product.
Note that this could be parallel with Jospeh Papp
Is Iron another catalyst of Rossi? If Im not wrong he said that there are
more than one catalyst
What is the isotopic quantities found in the ash
from Rossi?
Arnaud
_
From: Axil Axil [mailto:janap...@gmail.com]
Sent: samedi 25 août 2012 06:33
To: vortex-l@eskimo.com
Subject: Re:
Good idea! Im not sure Fe2O3 + 3 Ni = 3 NiO + 2 Fe is exothermic or even
if this reaction may exist.
_
From: Jeff Berkowitz [mailto:pdx...@gmail.com]
Sent: samedi 25 août 2012 20:11
To: arnaud.kod...@lakoco.be
Cc: vortex-l@eskimo.com
Subject: Re: [Vo]:video: An Explanation of
This video is a good summary of the last evolutions of Edmund Storm's
theory. Thank you, Edmund and Ruby to make it happen.
I've a bit of concern regarding neutrino emission. Edmund said that no
neutrino has been seen and his theory explains it why. That's good point.
Nevertheless he has
Audio has a very bad quality. Moreover it's Germenglish, poor French,
Italian and German.
Impressive 2 bodyguards . is he received some treats ?
Arnaud
_
From: Patrick Ellul [mailto:ellulpatr...@gmail.com]
Sent: samedi 8 septembre 2012 14:51
To: vortex-l@eskimo.com
Subject: Re:
Program of the congress can be found @
http://www.borderlands.de/Links/Kongress080912M-e.pdf
http://www.borderlands.de/Links/Kongress080912M-e.pdf
Arnaud
Dave,
Could it be explained by sintering effect of nano particles ? After cooling,
the inactive wire resistance drop of approximately 0.03 from the before
calibration situation. That's why Celani didn't try the 48W on its active
wire.
Arnaud
_
From: David Roberson
.
Jeff
On Tue, Sep 18, 2012 at 1:47 AM, Arnaud Kodeck
arnaud.kod...@lakoco.bewrote:
**
Dave,
Could it be explained by sintering effect of nano particles ? After
cooling, the inactive wire resistance drop of approximately 0.03 from the
before calibration situation. That's why Celani didn't try
the
data.
Dave
-Original Message-
From: Arnaud Kodeck arnaud.kod...@lakoco.be
To: vortex-l vortex-l@eskimo.com
Sent: Tue, Sep 18, 2012 4:47 am
Subject: RE: [Vo]:Question Concerning Celani's Charts
Dave,
Could it be explained by sintering effect of nano particles ? After cooling
We agree that the wire temperature is likely the most important factor, but
I hold the thought that the dissociation of the molecular hydrogen is
possibly bound with the gas temperature. The energy required to break the
bond must come from somewhere. Take a look at Celani's charts for deuterium
Hello Chuck,
You have made an interresting experiment worth to try to repeat. Teslaalset
and Dave are on it seems.
Chuch, did you try with another salt than Borax and succeed on excess heat
as you had with Borax ? Is Borax a key element ?
Best regards,
Arnaud Kodeck
Find here some simple calorimetry calculations :
Electrical energy given to the system : 4.33 hours @ 12 watt = 187056 J =
44677 cal
To rise the temp from 55 F to 146 F, the system need 50 cal/g of water.
(Assuming electrodes and recipient are negligible)
Assuming no loss of heat by
Celani doesn't give us the current and voltage of its wires (heating or
active wires). It might be interresting to see if there are some
variability. If the resistance shows some varaitions (as said in the
Celani's report of August), it must have also variations in current/voltage.
Those
19:29
To: vortex-l@eskimo.com
Subject: Re: [Vo]:Progress from the Martin Fleischmann Memorial Project
(Celani replication)
Arnaud Kodeck arnaud.kod...@lakoco.be wrote:
Celani doesn't give us the current and voltage of its wires (heating or
active wires). It might be interresting to see
temperature. I am confident that Celani can eliminate this possibility
quickly.
Dave
-Original Message-
From: Arnaud Kodeck arnaud.kod...@lakoco.be
To: vortex-l vortex-l@eskimo.com
Sent: Mon, Oct 8, 2012 1:24 pm
Subject: RE: [Vo]:Progress from the Martin Fleischmann Memorial Project
If claim of Rossi are right, the power density per gram of powder is awesome
596.85 W/g ( (14337-2400)/20 )
Celani's wire is around ~70 W/g
-Original Message-
From: Terry Blanton [mailto:hohlr...@gmail.com]
Sent: vendredi 12 octobre 2012 18:37
To: vortex-l@eskimo.com
Subject:
should have called that the energy density which has no meaning here
cause there are still energy to release of its cylinder ...
It seems, he is always confusing energy and power. With its kWh/h unity
which for means nothing physical.
-Original Message-
From: Arnaud Kodeck
Dave,
In selfsustaining mode, there is no input power to the cylinder. So I don't
understand the 3 first sentences of your email. Self sustain mode is no
input power and you say 2.359 kW. Duty cycle is 118/328 = 0.359. Time when
the system was not in self sustaining mode is 328-118 = 210 hours.
the behavior of his actual device to a reasonable degree. He is
a master at hiding the important information within a lot of non pertinent
details. Carefully follow my input and you can see what is actually
happening.
Dave
-Original Message-
From: Arnaud Kodeck arnaud.kod...@lakoco.be
It's just a DETACHMENT event. Let's hope them to find something
interresting after the ongoing calibration.
-Original Message-
From: Terry Blanton [mailto:hohlr...@gmail.com]
Sent: mercredi 24 octobre 2012 20:27
To: vortex-l@eskimo.com
Subject: Re: [Vo]:More leaked (?) info from
Hello Dave,
I wish you the best in your new campaign tests with borax. Please, keep us
up to date with discoveries and challenges you will have to face.
Arnaud
_
From: David Roberson [mailto:dlrober...@aol.com]
Sent: mercredi 24 octobre 2012 02:54
To: vortex-l@eskimo.com
Subject:
http://www.networkworld.com/columnists/2012/102612-backspin.html?page=1
Arnaud
Nice job !
But let me explain that your protection diodes aren't effective for current
overrun on sensing resistances. As you said, the voltage drop on forward
current of the diode is around 1V maybe a bit less . let's say 500mV. At
500mV, the resistance will dissipate (U^2/R) (0.5)^2/0.05 = 5
answer?
Jeff
On Sun, Oct 28, 2012 at 3:44 AM, Arnaud Kodeck arnaud.kod...@lakoco.be
wrote:
Nice job !
But let me explain that your protection diodes aren't effective for current
overrun on sensing resistances. As you said, the voltage drop on forward
current of the diode is around 1V maybe
For data acquisition I use 2 different configurations which give pretty good
results:
- Picoscope with my own Java librairies: http://www.picotech.com/
http://www.picotech.com/ For 200€ you have a double channels 100ns 8 bits
resolution ADC with USB connection
- Or for 50€
It's a shame to waste those nice products as a catalyst for LENR.
_
From: Alan Fletcher [mailto:a...@well.com]
Sent: mardi 30 octobre 2012 20:36
To: vortex-l@eskimo.com
Subject: [Vo]:Passi22 : The CHEESE paper
http://www.22passi.it/downloads/Cheese.pdf
CONSTANTINE MAGUIRE (C
Eric,
From Wikipedia, the isotope of fluorine 17 has a half life of 64.49s. This
value is close to the 58sfrom the report of Ed Storms and Brian Scanlan.
Can we also consider also the reaction 16O + p - 17F as a possibilities?
Arnaud
Jed,
I like your analogy with CPU's industry (and more generally with IC
industry). In this particular industry, there are 3 main fields:
Basic research
Conception
Manufacturing
For the 2 fields that are conception and manufacturing, there is currently
nothing occurring for LENR (except
http://www.quantumheat.org/index.php/follow/114-hydrogen-loading-commenced
Don't forget, the IP is owned by Celani and his team. Nevertheless, MFMP is
doing a great job to replicate the Celani's cell. It's nice to do the
replication openly.
_
From: Axil Axil [mailto:janap...@gmail.com]
Sent: dimanche 11 novembre 2012 04:54
To: vortex-l@eskimo.com
Subject:
until it is manufactured and
installed.
2012/11/9 Arnaud Kodeck arnaud.kod...@lakoco.be
For the 2 fields that are conception and manufacturing, there is currently
nothing occurring for LENR (except a small start from Rossi). Without a
proof of concept, it's too early to invest there. Once
I was thinking the same when listening/reading to the news today. US have a
long term vision about his energy consumption/production and stay stick to
it. The choice might not be the best and have pro and cons. Environmental
concerns arise against oil sands and shale gas .
Today, LENR is not
The age of the Renaissance started in the XVth century from what we call
today Italy. It started there before spreading in north Europe. History
repeats itself endlessly.
BTW, the Celani's wires are based on Isotan (Constantan trademark):
http://www.isabellenhuette.de/fileadmin/content/widerstandslegierungen/ISOTA
N-ISABELLENHUETTE-R.pdf?PHPSESSID=e5f77mrb8kiksmi0afimqcnub4
The Isotan contains 1% of Mn. Celani didn't say that Mn plays a magic role
in his wire.
James,
I've a problem with my HP calculator emulator which gives me 13.093 mm
d= v * t = v / f ( with v=1/f)
5630/430E3 = 13.093E-3 m = 13.093 mm
Arnaud
_
From: James Bowery [mailto:jabow...@gmail.com]
Sent: jeudi 22 novembre 2012 22:21
To: vortex-l@eskimo.com
Subject:
d = distance
v = speed (vitesse in french)
t = time and f = frequency
_
From: Arnaud Kodeck [mailto:arnaud.kod...@lakoco.be]
Sent: jeudi 22 novembre 2012 22:51
To: vortex-l@eskimo.com
Subject: RE: [Vo]:25 experiments completed with borax and nickels
James,
I've a problem
Jeff,
For AC bipolar pulse, I recommend you to have a look on the H bridge which
is a well known circuit in electronic.
4 MOSFETs and adequate control are all you need, to build it.
http://en.wikipedia.org/wiki/H_bridge
You may need to use a transformator to be able to put one
Jack,
Yes, you use a PWM signal and convert it in to an AC signal. For example
when PWM is 1, then it's + current, or if PWM is 0, then it's - current.
But if I understand, you need also a Zero current state as well. In this
case, the Power part of the schematic does not change. You keep
What are the energy put in and the energy get out of the system? There is no
point to try to make steam if there is no energy gain. The guy speaks about
thorium, but what are the clues that thorium has a role in the reaction?
The guy says once, steam is heavier than air. Hmm hmmm
No
From Jean-Paul Biberian's blog, the experiment is a replication of Mizuno
cell.
_
From: James Bowery [mailto:jabow...@gmail.com]
Sent: dimanche 25 novembre 2012 22:49
To: vortex-l@eskimo.com
Subject: Re: [Vo]:Cold fusion in an appartment (france, mizuno with W+2%Th)
The
Blade runner is coming back soon
The test of voight kampff might become
a reality.
Personally, I would prefer to know beforehand that Im facing a robot.
Arnaud
_
From: Jed Rothwell [mailto:jedrothw...@gmail.com]
Sent: samedi 1 décembre 2012 00:18
To: vortex-l@eskimo.com
Regarding radiation:
The Minnesota team is using a fused quartz tube. Since Quartz glass is more
transparent to the infrared wavelengths than borosilicate glass, the cell is
losing a significant amount of the heat energy compared to Celani because
Celani is using a borosilicate tube.
From my point of view, the wire has been burned out since November the 12th
during calibration in Helium. The power sent to the wire went up to 100W!
The temperature at the surface of wire reached a very high temperature
(Convection and radiation play here, so it is difficult to estimate it).
When
http://www.quantumheat.org/index.php/follow/176-eu-cell-2-active-wire-run
Promising results are shown from EU cell of MFMP !
Arnaud
Akira said :
I think it's safe to say that the MFMP finally successfully replicated
Celani's anomalous thermal effect from his treated Constantan wires. The
next step is now to determine whether that is a real effect or it's all
due to a really unexpected artifact lurking somewhere.
I would
at EU cell of MFMP
On 2012-12-12 22:57, Arnaud Kodeck wrote:
I would be a little more conservative. The excess power must be kept for
more than an hour or two, to at least remove any chemical reaction that
may
occur.
As shown now, the excess power has decreased just above 4W. That excess
I suspect a correlation with ambient temperature with a delay of around 6~8
min. The ambient temperature went down at 23:20 and the calculated excess
power decreased a few minutes later, now at 6W
On 2012-12-12 22:57, Arnaud Kodeck wrote:
As shown now, the excess power has decreased just
Minnesota for US
South of France for EU
I am confused about the location(s). Where exactly is/are the Celani
replications occuring?
Harry
The frequency of T° ambient and P_Xs are the same (Around 50 minutes). Is ir
a coincidence?
Arnaud
On 2012-12-13 03:29, Craig wrote:
This is so strange. I set the data in View Test Celani Cell #2, found
here:
http://data.hugnetlab.com/
to view back 4 hours. Then I selected only P_Xs
In the report, STM doesn't say where the neutron and gamma are measured. If
neutron and/or gamma have low energy, they might be absorbed by the vessel
before reaching the detector. Outside the reactor is not the best place for
the detector.
Regarding the input power versus temperature, it's clear
Dave,
You have made a very interesting analysis. What your model say when a +8W
apparent excess heat was reported with EU cell? Can your model able to
calculate the apparent excess power anytime? Not when equilibrium has been
reached.
For the data, did you take the US cell or EU cell? US
thermal capacity
of the cell. With accurate measurements of these parameters I can plot the
temperature versus time behavior to a high degree of accuracy.
Dave
-Original Message-
From: Arnaud Kodeck arnaud.kod...@lakoco.be
To: vortex-l vortex-l@eskimo.com
Sent: Tue, Dec 25, 2012 2:21 pm
Tesla,
To which Celanis patent are you referring to? So far, and to my knowledge,
Celani didnt fill a patent about his Constantan process. He has indeed
filled a patent for treating Nickel and alloy of nickel to load hydrogen,
but not specifically for Constantan.
Arnaud
_
Rossi stated a few days ago on his website that he was looking for an other
alloy of nickel with a higher melting point.
_
From: Teslaalset [mailto:robbiehobbiesh...@gmail.com]
Sent: dimanche 30 décembre 2012 11:56
To: vortex-l@eskimo.com
Subject: Re: [Vo]:Latest published LENR
This is an easy fake to do. There are 2 hidden small power sources. The
sources have equally same potential by means of Zener diode for example.
Small batteries are enough for the test with take 10 minutes to be
completed.
One source is placed inside the voltmeter in series with the (+) input.
I might attend as well to this interresting colloquium and see M Biberian. I
will decide tomorrow.
Arnaud
_
From: P.J van Noorden [mailto:pjvannoor...@caiway.nl]
Sent: mardi 15 janvier 2013 22:07
To: vortex-l@eskimo.com
Subject: Re: [Vo]:colloquium cold fusion 2013 in eindhoven
Who is this big European consortium? All suggestions are open here .
My guess is Siemens. Why?
1. Because they stopped all their investments in Green power technology
(Wind, Solar, .). If LENR becomes a commercial reality, all the business
with Green Technology will be obsolete in the
of
commercially available LENR reactors). For sure, I will not, for ever,
invest my money in those technologies.
_
From: Jed Rothwell [mailto:jedrothw...@gmail.com]
Sent: vendredi 18 janvier 2013 22:24
To: vortex-l@eskimo.com
Subject: Re: [Vo]:A Big European Consortium has an eye on MFMP
Arnaud
What has happened in Moscow?
I don't understand the percentage. What does this mean?
It has never been so high for the last 2 years, but other spikes occurred,
even higher.
Arnaud
-Original Message-
From: MJ [mailto:feli...@gmail.com]
Sent: jeudi 31 janvier 2013 16:30
To:
Hello Dave,
Your tool is powerful! Did you make also the calibration and exercises with
the EU cell? They have reported about ~6W excess heat when direct current
applied. The cell reports ~2.5W excess heat with an indirect heating.
US cells have been disappointing up to now. But EU cell shows
.
It is important to set goals that can be met since one can always improve
the capabilities and I feel that I have reached an acceptable performance
level for now.
Dave
-Original Message-
From: Arnaud Kodeck arnaud.kod...@lakoco.be
To: vortex-l vortex-l@eskimo.com
Sent: Sun, Feb 3, 2013 6:04 am
Hi Vortex,
The MFMP has just released an interesting update on their experiments to
replicate the Celani's effect. There is also a contribution from the new
protocol used by Celani.
http://www.quantumheat.org/index.php/follow/follow-2/206-tgoc
I will add also that the LENR generator set in the car might as well provide
wasted heat for the building. That does only need a few pipes from the car
to the heating system. The LENR generator will follow you and provide all
the time our energy needs locally.
The Tesla S is the way to go.
German decided to shutdown nuclear power plant well before Fukushima
disaster. Siemens has sold its nuclear department to the French. Fukushima
just convinced finally without doubt about nuclear fission energy.
With all those PV cells all around Germany and Benelux houses just make
sunny
German still have some nuclear power plants. Nuclear power plant can not be
started and shut down at will. Nuclear power plants continuously deliver
roughly the same amount of energy. The countries around Germany have also a
lot of power plants especially in France and in Belgium. Those power
This article from Oilprice.com is a really good bullshit. It will take ages
before LENR will have an impact on oil prices, and therefore on energy
prices. Big banks, and big oil companies will have (or already have) a
strong fight against LENR. But surely it will not be like it's explained in
the
their
manufacturing flexibility. This is like a combination of the Nazi economic
miracle and the post-war German economic miracle.
Major: Click on The Makers Revolution
On Fri, Mar 8, 2013 at 3:19 PM, Arnaud Kodeck arnaud.kod...@lakoco.be
wrote:
This article from Oilprice.com is a really good
OILPRICE.com
You didn't click through the link and watch the presentation by Anderson.
Do so.
On Fri, Mar 8, 2013 at 5:11 PM, Arnaud Kodeck arnaud.kod...@lakoco.be
wrote:
I don't understand what you exactly mean here? I'm aware of the new
robotization revolution (Baxter robot, and the same
Jed,
For cell phone the maximum power from the mobile is given by the equilibrium
between Uplink (Handset - base station) and Downlink (Base station -
Handset). Hopefully, base stations have a better maximum power and also a
better sensitivity for the receive path (around -110 dBm). The mobile
other
theories
Arnaud Kodeck arnaud.kod...@lakoco.be wrote:
At the beginning of a call, the mobile is emitting at full power. Then the
power is decreased over time if reception conditions are good at base
station.
. . .
For GSM 2G 900Mhz Band, the maximum power is 2W (33 dBm)
For GSM 2G
Eric,
Says that slow neutron is produced and absorbed by atoms in a LENR device.
In the order of 6.24E11 neutron captures per second for 1W, as you said,
some atoms which have received an absorbed neutron will become radioactive,
emitting gamma. Example: 58Ni + n - 59Ni - 59Co + e+. We should
50Hz antenna will make the phone very huge ...
If they extended the range to below 50Hz, they could pick up the stray
field
from the grid, which is much larger than the RF transmissions they are
harvesting now. Since most of this would be harvested indoors, it would
automatically be
There is nothing special here. Every gasoline car engine has it. Or am I
missing something?
In 5 min googling, I find this
http://christian.liljedahl.dk/guides/arduino-spark-plug
This circuit is far more reliable.
_
From: Jack Cole [mailto:jcol...@gmail.com]
Sent: mardi 26 mars
to use the circuit outlined in that as it
would seem likely to allow back surges that would damage the controller.
I'm certainly not claiming anything groundbreaking here. It is just a
piece of the puzzle for a control system.
Best regards,
Jack
On Tue, Mar 26, 2013 at 5:49 AM, Arnaud Kodeck
What could mean a 2 stages eCat ?
Is Rossi able to make different flavors of its magical powder ?
One powder with low temp start but with slow kinetic (Low kW),
called by Rossi the mouse
One powder with high temp start but with fast kinetic (High kW),
called by Rossi the cat
This
levels.
Fran
-Original Message-
From: Arnaud Kodeck [mailto:arnaud.kod...@lakoco.be]
Sent: Tuesday, March 26, 2013 9:41 AM
To: vortex-l@eskimo.com
Subject: EXTERNAL: Re: [Vo]:Rossi says third party tests concluded
What could mean a 2 stages eCat ?
Is Rossi able to make different
Axil,
How can you say that Nickel-48 is stable?
Arnaud
_
From: Axil Axil [mailto:janap...@gmail.com]
Sent: jeudi 28 mars 2013 20:11
To: vortex-l@eskimo.com
Subject: Re: [Vo]:thoughts on LENR energy
Physics has seven magic numbers. An atom with a magic number of protons or
, Arnaud Kodeck arnaud.kod...@lakoco.be wrote:
Axil,
How can you say that Nickel-48 is stable?
Arnaud
_
From: Axil Axil [mailto:janap...@gmail.com]
Sent: jeudi 28 mars 2013 20:11
To: vortex-l@eskimo.com
Subject: Re: [Vo]:thoughts on LENR energy
Physics has seven magic numbers
Jones,
Your theory below might explain also what Rossi has told a bit 2 years ago:
Some xRay are absorbed.
Some EM fields are escaping his eCat.
Moreover, in Pedrodragon, Rossi used Nickel, Hydrogen in the Bergius process
(http://en.wikipedia.org/wiki/Bergius_process). Sodium, potassium, and
talking about.
_
From: Arnaud Kodeck
Jones,
Your theory below might explain also what Rossi has told a bit 2
years ago:
Some xRay are absorbed.
Some EM fields are escaping his eCat
Jones,
It's very interesting theory. Nevertheless, in the web page you mention here
below, it says that Ni63 has a half life of around 100 years (a century). I
don't think Rossi's device can stay on for that long time.
Arnaud
_
From: Jones Beene
.
_
From: Arnaud Kodeck
Jones,
It's very interesting theory. Nevertheless, in the web page you
mention here below, it says that Ni63 has a half life of around 100 years (a
century). I don't think Rossi's device can stay on for that long time
We can see on the panorama picture ( http://postimg.org/image/6v14pk649/
http://postimg.org/image/6v14pk649/), the hot cat still in the metallic
shelf without electrical feedings.
The boxes of the cold cat are different from the October, 2011.
It looks like very amateur workshop behind the
Jones,
It's a very interesting analysis. I just to want to add 2 comments:
Rossi always claims to have very cost effective powder and catalyst. If
enriched nickel is needed, stop me if I'm wrong, but there is no intrinsic
reason to have a very high purity of Ni62. The last percents are always
_
From: Jones Beene [mailto:jone...@pacbell.net]
Sent: lundi 13 mai 2013 04:34
To: vortex-l@eskimo.com
Subject: RE: [Vo]:Palladium vs Ni-62
Well cost effective would be in the context of the value of the output
over time, no?
Rossi says a
I am surprised by the date of publication: Pentecost. Pentecost means the
descent of the Holy Spirit to the Apostles.
Coincidence?
-Original Message-
From: Alan Fletcher [mailto:a...@well.com]
Sent: lundi 20 mai 2013 11:51
To: vortex-l@eskimo.com
Subject: Re: [Vo]:Hot Cat report
Rossi has recently stated in JONP that local hot spots in its reactor were
the main issue. If a spot come to a certain upper threshold, the reactor
goes out of control. The keys are uniformity of heat production inside the
eCat and equal density of energy extraction along the entire surface. The
From Rossi statements, the powder melts and the reactor stops working.
_
From: mark.gi...@gmail.com [mailto:mark.gi...@gmail.com] On Behalf Of Mark
Gibbs
Sent: lundi 20 mai 2013 23:17
To: vortex-l@eskimo.com
Subject: Re: [Vo]: ECAT Time Domain Response
Does anyone know what happens
Thank you Jed to remind me this exchange you had with Celani. I was not
fully aware of every detail. When I was reading, an idea come to me mind.
Could it be possible that the secret sauce of Rossi is a gamma emitter? I
explain myself: Secretly, Rossi could have opened his reactor to adjust
Lovable : Is it an April fool ? (Look at the date of comment of Andrea
Rossi)
2.
Andrea Rossi
http://www.journal-of-nuclear-physics.com/?p=614cpage=1#comment-209521
April 1st, 2012 at 5:51 PM
Dear Steven N. Karels:
We use regular Ni, then we make series of treatment. The cost of treatment
From pictures in the Levi's report, the wires are not galvanic shielded
between the eCat and the controller. Thus frequency of the waveform (if any)
is low. And the waveform should be easily determined by a simple
oscilloscope.
2. I don't have a problem with this verification being done at
The temperature limitation of fission nuclear plant is due to temperature of
vaporization of water. The reactor must always be filled with liquid water.
At the pressure inside a fission reactor, the limiting temperature is just a
little above 300°C. The water is slowing the neutron. Without water,
1 - 100 of 172 matches
Mail list logo
