Am 02.12.2011 22:35, schrieb Jed Rothwell:
ecat builder wrote:
Hi All,
I posted the contents of a slide presentation by Dennis Bushnell that
he gave at at the LENR conference at Glenn Research Center, NASA.
Thank you! But please start a new thread when you change the topic.
Let me change the
Am 02.12.2011 23:33, schrieb Jed Rothwell:
Peter Heckert mailto:peter.heck...@arcor.de>>
wrote:
Why didnt you write: "I believe in the Rossi device, because
observers have noticed the surface heated up and because of this
poor insulation it must cool down over 4 hours wi
Am 03.12.2011 00:20, schrieb Jed Rothwell:
Peter Heckert mailto:peter.heck...@arcor.de>>
wrote:
Everybody knows that I believe there was definitive excess energy
measured in the Essen Kullander demo and in other demos, because
the water flow was too high to been heated
Hi,
some time ago I investigated the effects of ion wind in air.
Possibly you know this effect: A needle is charged to 5 kV or more and
this needle will blow a stream of charged air, that is rather strong.
I made experiments and blew the air into a water surface so see how
strong the flow is
Hi,
my idea is this:
place a needle in a pressurized deuterium stream and charge it to some
100 kV.
My previous experiments have shown, that a stream of nonconductive gas
is able to conduct electricity.
For example a ordinary needle placed in dry air will cause an ion wind,
if charged to 10
Am 03.12.2011 20:57, schrieb Jed Rothwell:
Mary Yugo mailto:maryyu...@gmail.com>> wrote:
We need more robust, long running, high output, credible experiments.
SRI and the ENEA have done robust, long running, credible experiments
for 20 years, albeit at low output. Skeptics, the DoE and mo
Am 03.12.2011 16:20, schrieb Horace Heffner:
I suggest that the dark zone at the tip of the needle is not due to a
vacuum there. It is more likely due to the average delay for
recombination of the ions and electrons. Electron recombination with
ions is likely what produces most of the light.
Am 03.12.2011 22:14, schrieb Harry Veeder:
On Sat, Dec 3, 2011 at 3:38 PM, Peter Heckert wrote:
I believe there is a vacuum for these reasons:
1) I placed a charged needle 1-2 cm above a water surface. The air blow
makes a sharp, mm deep and mm wide hole into the water surface.
If I assume
Am 03.12.2011 23:00, schrieb Horace Heffner:
Say, Bill Beaty's experiments made it as a reference on wikipedia!
http://en.wikipedia.org/wiki/Water_thread_experiment
Yes, this experiment was made by others too and published in science
journals.
It must be seen that a strong current flows thro
Am 03.12.2011 22:57, schrieb Horace Heffner:
Here are some URLs related to Bill Beaty's air threads:
http://amasci.com/weird/unusual/airexp.html
http://www.youtube.com/watch?v=-_prcDanfMw
http://www.youtube.com/watch?v=iLG8gKb-lyk
http://www.youtube.com/watch?v=CKvLUL8f4LU
http://amasci.com/
Am 03.12.2011 23:51, schrieb Horace Heffner:
On Dec 3, 2011, at 1:30 PM, Peter Heckert wrote:
Am 03.12.2011 23:00, schrieb Horace Heffner:
Say, Bill Beaty's experiments made it as a reference on wikipedia!
http://en.wikipedia.org/wiki/Water_thread_experiment
Yes, this experiment was
Am 04.12.2011 00:01, schrieb Peter Heckert:
I dont believe, he used this for the water thread experiment.
This needs more current.
I tried with deionized water, but my supply was too week. It should
deliver about 100µA.
Its a TV split diode flyback transformer driven by a selfbuild
Am 04.12.2011 00:29, schrieb Horace Heffner:
On Dec 3, 2011, at 2:24 PM, Peter Heckert wrote:
Am 04.12.2011 00:01, schrieb Peter Heckert:
I dont believe, he used this for the water thread experiment.
This needs more current.
I tried with deionized water, but my supply was too week. It
Another video (62 minutes) about the water thread experiment:
http://youtu.be/N1At3Gcd-No
Its from SETI and demonstrates the science behind.
It coveres everything from flow to conductivity to bubbles to
thermographic measurements and heavy water experiments.
Very interesting are the Schlieren p
Am 04.12.2011 01:16, schrieb Peter Heckert:
Another video (62 minutes) about the water thread experiment:
http://youtu.be/N1At3Gcd-No
Its from SETI and demonstrates the science behind.
It coveres everything from flow to conductivity to bubbles to
thermographic measurements and heavy water
Am 04.12.2011 01:41, schrieb Horace Heffner:
This is about the water bridge experiment, not Bill Beaty's water
thread experiments.
His fine threads extended multiple times the length of the water
bridge, and were sustained indefinitely, with orders of magnitude less
current. Read the archiv
Am 04.12.2011 05:07, schrieb Horace Heffner:
That is because Bill did not call them "water thread" experiments. My
mistake, and bad memory. The above wasser.html reference was indeed
about water bridge experiments, not Bill Beaty's air thread
experiments, which are a very different thing - t
Am 04.12.2011 08:04, schrieb Alain dit le Cycliste:
after defkalion who say they will install a webcam to show
an hyperion working
http://www.defkalion-energy.com/forum/viewtopic.php?f=17&t=587
it seems that rossi agree too for a 24x7 show
http://www.e-catworld.com/2011/12/rossi-open-to-live-str
Am 04.12.2011 06:56, schrieb Alain dit le Cycliste:
I've look a gain, and I'm still suspect about using ZPE, because ZPE is
only an energy that you cannot use to go below... by definition.
There are new reports that photons where extracted from ZPE:
http://www.technologyreview.com/blog/arxiv/2
Am 04.12.2011 13:40, schrieb Horace Heffner:
I am familiar with air ions. The phenomenon measured by Bill Beaty in
the presence of much water vapor, and having nano-amp current, I think
is not made of non-polarized air molecules, but of a contiguous string
of polarized molecules. Here is on
Am 04.12.2011 14:30, schrieb Horace Heffner:
Some relevant quotes of interest from Bill Beaty at:
http://amasci.com/weird/unusual/airexp.html
"The "threads" can survive in a zero-field region. I made a crude
"thread gun" and passed a thread through an accelerator ring composed
of an aluminum
Am 04.12.2011 21:57, schrieb mix...@bigpond.com:
In reply to Peter Heckert's message of Sat, 03 Dec 2011 01:36:18 +0100:
Hi,
[snip]
The other problem is, where to get deuterium in pressurized bottles ;-)
[snip]
That one isn't really a problem. Electrolysis can easily produce high gas
pressures
- Original Nachricht
Von: mix...@bigpond.com
An: vortex-l@eskimo.com
Datum: 05.12.2011 03:31
Betreff: Re: [Vo]:How to make a 100 kV Lenard valve for deuterium fusion - idea
> BTW exactly which reactions are you looking for, and do you expect them to
> be
> brought about by
- Original Nachricht
Von: Jones Beene
An: vortex-l@eskimo.com
Datum: 05.12.2011 02:39
Betreff: RE: [Vo]:Speaking of MAHG
> The 15 kHz frequency is in the low ultrasonic range, and has been seen in a
> number of claimed gainful (or very efficient) devices: most recently the
>
Am 05.12.2011 19:50, schrieb Robert Lynn:
It is clearly demonstrable that there exist mechanisms (of unknown type) in
room temperature condensed matter to create at least 10's of keV, check out
the rather fascinating following video:
http://www.disclose.tv/action/viewvideo/10588/X_Rays_from_Sello
Am 05.12.2011 21:44, schrieb mix...@bigpond.com:
Hi,
The (private?) Swiss company Glencore has acquired all the shares of the largest
Australian Nickel producer Minara.
This is not a problem. The e-cat does not use much nickel. We can
extract it from Euro coins or from others.
They contain 25
Am 05.12.2011 22:03, schrieb Alain dit le Cycliste:
not so false.
according to Rossi's E-cat figures, it would consume 25% of annual Ni
production to produce the annual energy.
in my opinion, according to defkalion info, the powder seems simple.
the reactor and the H bottle seems the most expens
According to the report of Kullander & Essen Rossi has given to them a
sample of unused Nickel powder and a sample of used powder.
It was often said, they found only natural isotope distribution in the
used powder.
I could not find reports about the new powder.
Rossi has multiply claimed that
Am 05.12.2011 22:56, schrieb Jed Rothwell:
Stephen A. Lawrence wrote:
Have you read nothing of how psychics operate?
Actually, I have read a lot about that, possibly more than Yugo has. I have
also read about stage magicians. In both cases their methods could not
begin to fool anyone looking in
Am 05.12.2011 23:25, schrieb Jed Rothwell:
Peter Heckert wrote:
Watch this magician: http://youtu.be/VsYDRRGmpXU
At 6:00 he makes steam and he allows more access than Rossi ;-)
His Japanese is pretty good.
Do you seriously think that a chemist examining that cup would not
find the source
- Original Nachricht
Von: Aussie Guy E-Cat
An: vortex-l@eskimo.com
Datum: 07.12.2011 08:36
Betreff: Re: [Vo]:[Rossi] University R&D has gone away?
> Rossi has said the 1st customer is a US military research contractor and
> that the first plant is installed in the US.
If
- Original Nachricht
Von: Aussie Guy E-Cat
An: vortex-l@eskimo.com
Datum: 07.12.2011 08:57
Betreff: Re: [Vo]:[Rossi] University R&D has gone away?
> It is about which nation controls LENR as it has the capability to
> reshape the world. As for living happily ever after, w
Probably Rossi used some duct tape to repair the reactor. This makes Gamma rays
;-)
Honestly, after all was happened, better: NOT happened, such a singular
observation is without worth.
Of course there might be a strange mechanism producing gamma rays, possibly a
welding apparatus or another in
- Original Nachricht
Von: Berke Durak
An: vortex-l@eskimo.com
Datum: 07.12.2011 14:48
Betreff: Re: [Vo]:Celani: gamma spike during ignition of Rossi reactor
> Francesco Celani is a professor at the Italian National Institute of
> Nuclear Physics. He performed measurements
Am 07.12.2011 16:03, schrieb Jed Rothwell:
Mattia Rizzi wrote:
No gamma radiation was measured over background.
If inside the reactor there was a 10kW gamma source, with a hole in
shielding, everybody had died.
All these data is inside the Bianchini report, in January.
I do not think that c
oned computer screen was there. This should
flash.
But wait! Where not fluorescent lamps there? What do these? Shouldnt
they flash?
How does a laptop react to gamma bursts that can kill?
best regards,
Peter
On Wed, Dec 7, 2011 at 11:09 AM, Peter Heckert
wrote:
Am 07.12.2011 16:03, schrieb Jed Roth
I think it is not necessary to test something that is known and expected from
theory and experience.
If there is no thermal flow, then there are no temperature differences, this is
known from physics.
So especially when the measurment location is wrapped with thermal isolation a
thermoelement fi
- Original Nachricht
Von: Jed Rothwell
An: vortex-l@eskimo.com
Datum: 08.12.2011 15:59
Betreff: Re: [Vo]:Will tests surface mounted thermocouples on pipe
> wrote:
>
> >
> > It is necessary to think about unexpected effects:
> > It is clear, in Rossis setup there was a th
- Original Nachricht
Von: Michele Comitini
An: "vortex-l@eskimo.com"
Datum: 08.12.2011 14:29
Betreff: [Vo]:Article - Quantum Entanglement Allows Diamonds to Communicate
> http://www.laboratoryequipment.com/news-Quantum-Entanglement-Allows-Diamonds
> -to-Communicate-120511
- Original Nachricht
Von: Jed Rothwell
An: vortex-l@eskimo.com
Datum: 08.12.2011 15:59
Betreff: Re: [Vo]:Will tests surface mounted thermocouples on pipe
> wrote:
>
> >
> > It is necessary to think about unexpected effects:
> > It is clear, in Rossis setup there was a th
- Original Nachricht
Von: Jed Rothwell
An: vortex-l@eskimo.com
Datum: 08.12.2011 17:00
Betreff: Re: [Vo]:Will tests surface mounted thermocouples on pipe
> peter.heck...@arcor.de wrote:
>
> > How can you say this is incorrect? Do you know everything, great master?
> I can
Am 08.12.2011 17:20, schrieb Robert Leguillon:
Unfortunately, it's not quite that simple for two reasons:
1) the secondary flow rate was much higher than the primary, moving the
equilibrium point closer to the hot side
2) the primary flow rate is unknown, and quite possible variable, moving the
Am 08.12.2011 19:49, schrieb David Roberson:
Is the entanglement robust enough to survive a long shaky trip? I recall
reading that it is not easy to keep the effect for a long time.
The entanglement of macroscopic objects is probably not stable enough.
It is possible to slow down entangled pho
Am 08.12.2011 20:13, schrieb Jed Rothwell:
Peter Heckert wrote:
Thermal insulation can be used to avoid heat loss, but because the absolute
temperature was not much above ambient, not much loss is expected. Anyway,
thermal isolation is cheap and would eliminate the influence of ambient air
Am 08.12.2011 20:19, schrieb Jed Rothwell:
Mary Yugo wrote:
Jed's well intentioned experiments won't help either unless he gets
himself a heat exchanger or properly simulates it with a nice heavy
steam-heated copper . . .
My tests were rudimentary. But in my opinion, they helped a hell a lo
Am 08.12.2011 20:53, schrieb Jed Rothwell:
Peter Heckert wrote:
If there is an air gap of 0.1mm between metal and thermoelement, then it is
not nonsense.
I doubt that. I would like to see you prove it. I do not think this would
cause even a 0.1°C difference.
Can you suggest a way to
Am 08.12.2011 21:31, schrieb Jed Rothwell:
Peter Heckert wrote:
Can you suggest a way to deliberately introduce such a small gap? Perhaps
with a thin piece of paper instead of an air gap?
A thin piece of plastics. This is also good for electrical isolation.
Like Saran wrap? (What you
Jed, seriously:
If you say, Rossis thermomeasurements are fine, does this mean that you
dont see the possibility for easy and cheap improvements?
All points that are discussed here can be eliminated by better
thermoelement placement almost without efforts and costs.
If somebody does not admit
Am 08.12.2011 22:17, schrieb Jed Rothwell:
If somebody does not admit this, then he must be a blind mouse.
I not only admitted it, I emphasized it in my report. However, these
problems -- bad as they are -- do not negate the findings.
They do negate the findings. To prove a billion dollar inven
Am 08.12.2011 22:49, schrieb Jed Rothwell:
Peter Heckert wrote:
So what are you saying? Is there a problem with a 0.1 mm gap, or is there
not? Are you asking me to waste my time doing a test that will not prove
anything?
I have never asked you to do this. It was your wish.
It is a simple
Jed, if I find the time tomorrow during work, I do the test myself.
This is better. I fear your test will not be correct.
I will use a resistor in an aluminium housing as a heat source and two
thermoelements and two instruments.
One thermocouple will be in close metallic contact to the resistor
Nachricht
Von: Jed Rothwell
An: vortex-l@eskimo.com
Datum: 09.12.2011 03:54
Betreff: Re: [Vo]:Yo: Peter Heckert! Is a 0.1 mm gap a problem or not?
> Peter Heckert wrote:
>
> One thermocouple will be in close metallic contact to the resistor and the
> > other will be is
Hi,
Where I work: http://hphsite.de/Vortex/AtWork.jpg
Measuring Arrangement: http://hphsite.de/Vortex/Overview.jpg
Macro detail - tape: http://hphsite.de/Vortex/Tape.jpg
(It is worth to note, that a small air gap or spurious glassfiber
isolation material had the same effect as the tape.)
The the
Am 09.12.2011 18:59, schrieb Jed Rothwell:
Peter Heckert wrote:
The thermoelement on the tape has a bad contact to the metal and measures
preferrably the air temperature.
This is not a valid test. You have to cover up the thermocouples. Rossi did
not leave them open to the air.
I assume
Am 09.12.2011 19:40, schrieb Jed Rothwell:
Heckert can also test for this with some insulation. - Jed
Sorry, its only possible when the boss is not around ;-)
We are rather busy now, at end of year many customers must use up their
budget, if they dont do this they get less next year...
Peter
Am 09.12.2011 22:11, schrieb Horace Heffner:
Photos are from Alan Fletcher's site, the page with the nifty FEA
simulations:
http://lenr.qumbu.com/rossi_ecat_oct11_spice.php
If air bubbles are collected at the blue side, this would produce rather
large errors in thermal coupling:
http://l
Am 10.12.2011 21:08, schrieb Colin Hercus:
Did you see in the specs that the heat exchanger should be mounted
vertically when used for phase change. Having it horizontal should reduce
effectiveness and err in Rossi's favour
Yes. It must be vertical.
But I think the error should be in Rossi's dis
Am 10.12.2011 17:51, schrieb Mary Yugo:
I wish someone had taken the considerable trouble to duplicate Rossi's
small E-cat and "Ottoman" (Oct 6) experiments. By this, I mean to make
devices as similar as possible as Rossi's and to show that the experimental
results K&E and Lewan got could be obt
Am 10.12.2011 22:46, schrieb Robert Leguillon:
But the "E" class is listed specifically as a single-phase heat exchanger. Does
it double as a condenser?
http://www.swep.net/index.php?tpl=products-ranges&lang=en&id=352
I dont know, if this matters. Possibly it has only to do withthe
pressure.
Am 10.12.2011 23:06, schrieb Alan Fletcher:
With the 1:40 primary:secondary flows there's most likely not a problem. And
any problems (steam not condensed) would give a lower calculated power (as
pointed out, in Rossi's -- ie less likely fake-- favour.)
The question is, if it works in horicont
Am 10.12.2011 23:03, schrieb Alan Fletcher:
http://www.spiegel.de/wissenschaft/technik/0,1518,801836,00.html
(google translate is tolerable)
Not TOO bad ... of course, they call a Plasma Physicist at Max Planck Institute to say
the mandatory "defies the laws of physics".
This will reach many r
Am 11.12.2011 00:04, schrieb Jed Rothwell:
Peter Heckert wrote:
By this, I mean to make
devices as similar as possible as Rossi's and to show that the
experimental
results K&E and Lewan got could be obtained by mismeasurement rather than
LENR heat production.
Possibly it is suff
Am 11.12.2011 00:53, schrieb Jed Rothwell:
Peter Heckert wrote:
You should know, I have said it can be done with a secret wireless heater
switch and/or with a vacuum sucking out water.
I suggest you prove that. Build something with wires large enough to
produce this much heat yet which
Am 11.12.2011 01:46, schrieb Aussie Guy E-Cat:
This is silly. There was a clamp on amp meter on the mains cord and on
the heater wires going into the E-Cat. Power consumption was recorded
during the self power run. Refer to the Higgins data. Are you
suggesting that during the self powering peri
y hurt my confidence into this field.
I begin to understand why it is ignored by mainstream.
Dave
-Original Message-----
From: Peter Heckert
To: vortex-l
Sent: Sat, Dec 10, 2011 7:32 pm
Subject: Re: [Vo]:Why not duplicate Rossi's setups and see how they work
without LENR?
Am 11
There are scientists that report much better results:
http://pages.csam.montclair.edu/~kowalski/cf/204israel.html
citation:
- Run #64b gave 1500% excess heat over a duration of 80 hours with a
total excess energy of 4.6 Megajoules
So, why do they all stare at Rossi and his poor COP and question
Am 11.12.2011 15:15, schrieb Robert Lynn:
The key is the brass manifold - the heat exchanger is unimportant. But I
have not seen the Brass manifold anywhere on their website.
I dont think the heatexchanger is unimportant.
I got the heater applications handbook from SWEPS website.
http://www.swe
Am 11.12.2011 16:49, schrieb David Roberson:
The exchanger did work in the horizontal position. All it has to do is to
condense and cool the vapor/water mixture that enters into the primary. The
temperature of the exiting liquid was low enough and that is proof that the
device transferred th
Am 11.12.2011 17:12, schrieb David Roberson:
Peter, Mats Lewan measured the output water temperature at two points in time
and it was quite low. Review his report. What evidence do you have that the
heat exchanger did not transfer the heat?
I did not say that.
Of course it transferred the he
I downloaded an image from Ny Teknik and enhanced contrast and
brightness and sharpened it, to make the thermoelement visible:
http://hphsite.de/vortex/thermoelement.jpg
degrees in Lewans report.
If the primary delta_t was 100° then this means, the energetic
efficiency of the heatexchanger was 99 %.
This is pretty good and is probably because this exchanger is designed
for higher flow rates.
Best,
Peter
Am 11.12.2011 21:06, schrieb Alan Fletcher:
"Peter He
o
this.
Any test with similar magnitudes will give similar results. Why should I
repeat it? The result is plausible.
Only an experiment with the real thing could bring new findings, but i
doubt it.
-Mark
-----Original Message-
From: Peter Heckert [mailto:peter.heck...@arcor.de]
Sent: Sunday,
Am 11.12.2011 22:57, schrieb Mark Iverson-ZeroPoint:
Peter:
There's a bit of a language barrier here...
I was not suggesting that you actually repeat the analysis, or do something a
little different... but I think most readers will understand my point.
I dont understand your point.
If I could
Allan Sterling has an interesting article about it:
http://www.naturalnews.com/026116_energy_free_population.html
The article is very long and I citate only the end.
citation:
Handing this over to human beings now would be like giving a child a set
of big red buttons for launching nuclear missi
Am 12.12.2011 23:16, schrieb Peter Heckert:
Allan Sterling has an interesting article about it:
http://www.naturalnews.com/026116_energy_free_population.html
Sorry, I was in error, this article is not by Sterlin Allan. I found it
linked, when searching for his religious articles.
But I think
So far I have read, they got strong evidence, but not this high evidence that
is needed for such a fundamental discovery.
They are not like Rossi. They will test it again and again and doubt and harden
it by all possible methods, before they confirm it.
Scientific evidence is yet not reached.
Bushnell had the vision to make Mars habitable. Ok, thats an utopy.
But can make deserts green and siberia habitable.
Its unclear what this does to global climate.
It can solve the water problems in far east and israel and can prevent wars for
oil.
But this all must be seen with care. Each new te
Am 13.12.2011 23:21, schrieb ecat builder:
Hi All,
Just a brief update on the replication attempt by "Chan". Chan is an
anonymous poster who claims to have replicated the Rossi reaction
using powders on two builder sites, ecatbuilder.com and buildecat.com.
He uses an RFG connected to a inductio
- Original Nachricht
Von: mix...@bigpond.com
An: vortex-l@eskimo.com
Datum: 14.12.2011 07:22
Betreff: Re: [Vo]:Fwd: check out this 10,000 volt single cell battery near end
of lecture
> In reply to fznidar...@aol.com's message of Tue, 13 Dec 2011 23:30:30
> -0500
> (EST):
- Original Nachricht
Von: Moab Moab
An: vortex-l@eskimo.com
Datum: 13.12.2011 21:51
Betreff: [VO]: ENEA endorses the phenomenon
> my first post ...
>
> Mary Yugo wrote
>
> > As Carl Sagan was fond of pointing out, the more extreme the claim, the
> > better the evidence h
Lets assume we play in lottery. Sometimes we win, mostly we dont win.
Is this a scientific proof that lottery delivers excess money?
No, it is not. I think this is clear to everybody, no explanation is necessary.
Of course, only those people who have won, report.
Those, who have lost, dont report
- Original Nachricht
Von: peter.heck...@arcor.de
An: vortex-l@eskimo.com
Datum: 14.12.2011 12:06
Betreff: [Vo]:Statistics and LENR and Thermodynamics - a new theory.
> Lets assume we play in lottery. Sometimes we win, mostly we dont win.
> Is this a scientific proof that lo
Am 14.12.2011 21:05, schrieb Mary Yugo:
On Wed, Dec 14, 2011 at 11:38 AM, Charly Sistovaris
wrote:
That's in Athens, not Xanthi which is a town in the North.
You often bring up good arguments, but the bickering is a tiresome.
I simply copied the information given by Defkalion and indeed it's
Am 15.12.2011 19:12, schrieb Peter Heckert:
Am 14.12.2011 21:05, schrieb Mary Yugo:
On Wed, Dec 14, 2011 at 11:38 AM, Charly Sistovaris
wrote:
That's in Athens, not Xanthi which is a town in the North.
You often bring up good arguments, but the bickering is a tiresome.
I simply copie
Am 15.12.2011 19:50, schrieb Alan J Fletcher:
At 10:32 AM 12/15/2011, Peter Heckert wrote:
The mechanism is constructed in such a way that any hard x-rays
so far, so good ...
or external gamma measurements are detected and it will trigger.
How can you detect an EXTERNAL gamma measurement
Hi,
my thesis is that matter sucks up energy and this is the reason for gravity.
I dont know in which frequency range this happens, but I think matter
sucks up zeropoint energy and converts it to matter.
There was a similar theory that was discussed by Clerk Maxwell and
Boltzmann and others.
- Original Nachricht
Von: "Wm. Scott Smith"
An: vortex-l@eskimo.com, peter.heck...@arcor.de
Datum: 16.12.2011 00:26
Betreff: [Vo]:Possible Proof of Peter's theory of gravity and New Matter Accrual
>
> Peter, your thoughts about matter "sucking" ZPE and accruing mass may b
LENR - Low Energy Nuclear Reactions, is this possible?
If we see physics as a statistical phenomenom, then energy is another
word for probability.
So, Low Energy reactions are low probability reactions - reactions that
dont happen frequently ;-)
It is therefore improbable to get energy out of
Am 16.12.2011 21:59, schrieb Aussie Guy E-Cat:
http://www.youtube.com/watch?v=VymhJCcNBBc
It is interesting and looks very convincing.
However, it is unclear to me how performant this is.
For example they measure neutrons. So far I know the neutrons from
cosmic rays are 20 neutrons /(cm^2*s)
Am 18.12.2011 05:17, schrieb Sean True:
If Dr. Miley is in need of low thousands of dollars to get to a breakthrough,
is there a possibility of using kickstarter.com to raise the money? I'd kick in
a thousand dollar pledge if Jed said it would get the good doctor over the hump.
Miley is closel
- Original Nachricht
Von: Jed Rothwell
An: vortex-l@eskimo.com
Datum: 19.12.2011 03:03
Betreff: [Vo]:"Private information" about Rossi was the Ampernergo tests
described by McKubre
> Here is a key issue. Rossi's personality is an open book thanks to his
> website. That i
You write too much. A lot of citations and it is unclear in which context there
where made.
A citation from Westinghouse, who where a competitor.
(If this citation was about AC, then Westinghouse was correct. Not anything
that Edison did or propagated, was a success)
I think your other statemen
Am 19.12.2011 15:43, schrieb Jed Rothwell:
Susanna Gipp wrote:
Do we have something else excepts a bunch of words ?
Yes, data.
Do you know who they are ?
Yes, I said I did. Please read my message more carefully.
Same what Allan Sterling says about the Penderev Magnet Motor.
He kno
501 - 593 of 593 matches
Mail list logo