The gigabit UBNT stuff (excluding AF5x and AF) has to have ground on pins 3 & 6 to connect at a gig.
On Thu, Apr 16, 2015 at 6:02 PM, Mathew Howard <[email protected]> wrote: > So what we need is a Syncinjector with jumpers like on the Gigabit PoE > injectors... > > On Thu, Apr 16, 2015 at 6:57 PM, Josh Luthman <[email protected] > > wrote: > >> Yup screwed there :( >> >> Josh Luthman >> Office: 937-552-2340 >> Direct: 937-552-2343 >> 1100 Wayne St >> Suite 1337 >> Troy, OH 45373 >> On Apr 16, 2015 7:42 PM, "Mathew Howard" <[email protected]> wrote: >> >>> If I remember right, the AF5x pinout is 1/2 & 4/5 positive and 3/6 & 7/8 >>> negative. >>> >>> Airmax stuff is all 4/5 positive and 7/8 negative, I imagine the 10/100 >>> stuff would work fine with the power pairs swapped, but I don't know what >>> that would do to gigabit. I don't think it's going to work with AF5x, since >>> they use power on all four pairs. >>> >>> On Thu, Apr 16, 2015 at 6:19 PM, Josh Luthman < >>> [email protected]> wrote: >>> >>>> I didn't check...sorry. It's on the roof so I can go up and look >>>> tomorrow. >>>> >>>> >>>> Josh Luthman >>>> Office: 937-552-2340 >>>> Direct: 937-552-2343 >>>> 1100 Wayne St >>>> Suite 1337 >>>> Troy, OH 45373 >>>> >>>> On Thu, Apr 16, 2015 at 7:14 PM, George Skorup (Cyber Broadcasting) < >>>> [email protected]> wrote: >>>> >>>>> No pinout!? >>>>> >>>>> On 4/16/2015 6:10 PM, Josh Luthman wrote: >>>>> >>>>> It says 24v/1a and is gigabit. It is a bit different than the >>>>> Nanobeam POEs. It also doesn't work with an NSM5 for certain. >>>>> >>>>> >>>>> Josh Luthman >>>>> Office: 937-552-2340 >>>>> Direct: 937-552-2343 >>>>> 1100 Wayne St >>>>> Suite 1337 >>>>> Troy, OH 45373 >>>>> >>>>> On Thu, Apr 16, 2015 at 6:39 PM, George Skorup (Cyber Broadcasting) < >>>>> [email protected]> wrote: >>>>> >>>>>> What does the AF5x power supply say on the label for pairs or >>>>>> pinouts? Or is it the same as their other 24V/1A supplies, but gigabit? >>>>>> >>>>>> On 4/16/2015 5:29 PM, Josh Luthman wrote: >>>>>> >>>>>> I'm mostly concerned with the Ubnt Airmax stuff (24v) and AF5x. >>>>>> Obviously the ePMP works. >>>>>> >>>>>> >>>>>> Josh Luthman >>>>>> Office: 937-552-2340 >>>>>> Direct: 937-552-2343 >>>>>> 1100 Wayne St >>>>>> Suite 1337 >>>>>> Troy, OH 45373 >>>>>> >>>>>> On Thu, Apr 16, 2015 at 6:12 PM, George Skorup (Cyber Broadcasting) < >>>>>> [email protected]> wrote: >>>>>> >>>>>>> AFAIK, the 450AP GigE interface is still powered only on pins 4, 5, >>>>>>> 7 & 8. Probably applies to the ePMP Sync radio too. >>>>>>> >>>>>>> So, with that in mind.. does the UBNT GigE PoE stuff use all 4 pairs >>>>>>> for power? If it's 4, 5, 7 & 8, it may be possible, but... you'd have to >>>>>>> flip the blues and browns at one end. I don't know what that would do >>>>>>> for >>>>>>> the GigE data interface though. It might not work. You can use a 568B to >>>>>>> 568A (aka standard cross-over) cable and GigE still works fine, but I'm >>>>>>> not >>>>>>> sure about crossed blues and browns. >>>>>>> >>>>>>> Someone smarter than me would probably have to give you a thumbs up >>>>>>> or down. >>>>>>> >>>>>>> >>>>>>> On 4/16/2015 4:55 PM, Josh Luthman wrote: >>>>>>> >>>>>>>> Has anyone tried these syncinjectors for Ubnt Airmax radios? What >>>>>>>> about anything else? I'd love to use this one product for all sites >>>>>>>> from >>>>>>>> now on. >>>>>>>> >>>>>>>> Is it possible to run the AF5x? >>>>>>>> >>>>>>>> Josh Luthman >>>>>>>> Office: 937-552-2340 >>>>>>>> Direct: 937-552-2343 >>>>>>>> 1100 Wayne St >>>>>>>> Suite 1337 >>>>>>>> Troy, OH 45373 >>>>>>>> >>>>>>> >>>>>>> >>>>>> >>>>>> >>>>> >>>>> >>>> >>> >
