I'll start this post by saying THANKS to all involved who have provided
me with the answers to my last two posts (as frustrating as I'm sure
they were). So far my FBSD box is living up to its reputation as being a
windows replacement. Now I would like to configure a Logitech wireless
mouse and
Just add to /boot/loader.conf:
module-name_load=YES
On Fri, Feb 27, 2004 at 03:08:07PM -0500, Shaun T. Erickson wrote:
In linux, I'd use /etc/modules.conf to list and configure any kernel
modules I want loaded at boot time. How is that done in FreeBSD?
I see that there are a *lot* of kernel
On Sat, 28 Feb 2004 04:14:55 +
Andrew Boothman [EMAIL PROTECTED] wrote:
Mark Weisman wrote:
Anyone know of a good Anti-virus software that works on FBSD?
If you're looking for something to scan email I constantly hear good
things about Vexira MailArmor
On Thursday 26 February 2004 19:53, Derrick wrote:
I picked up one of these :
http://www.pcchipsusa.com/prod-usbwirelesslanadaptor.asp
(nice deal, buy for 29.95, and get a 29.95 rebate.)
i know the Intersil Prism 3.0 is supported, on some wi - but is this
device supported? I don't think it
Hi Guy Harrison,
you wrote.
Do you get the same result if booting without ACPI?
GH Yes. I'm assuming here that the [default] boot option does not have ACPI
GH enabled (if so, how to disable it?). The boot results are identical to
GH when I select option 2 to boot with ACPI enabled.
I too get a
Out of curiosity does anyone have this combination working?
I managed to get it automounting NFS no problem, but would like to
know if it's worth spending another few hours trying to get
mount_smbfs to cooperate with it or if it's just a lost cause.
Thanks,
Graeme
i have just upgraded ruby 1.8 and i wanted to run pkgdb and i get this:
=== Registering installation for ruby-1.8.1_2
=== SECURITY REPORT:
This port has installed the following files which may act as network
servers and may therefore pose a remote security risk to the system.
Please will you re-admit me to the mailing list
rod brookes
___
[EMAIL PROTECTED] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to [EMAIL PROTECTED]
On Saturday 28 Feb 2004 10:40 am, albi wrote:
i've got autofs + samba working on Linux (from Linux to Linux
actually), haven't tried on FreeBSD (yet)
documentation on the internet was not very much at all, but still
managed to make it work :)
i can make a small howto (later) for you if you
Attention: [EMAIL PROTECTED]
A Disallowed attachment type was found in an e-mail message sent by you.If you still
wish to send this file, please rename it first to be .TXT (e.g.
rename the file software.exe to be software.txt - right-click on the
filename and select Rename). When the
- Original Message
From: albi [EMAIL PROTECTED]
To: [EMAIL PROTECTED] [EMAIL PROTECTED]
Subject: Re: Anti-Virus?
Date: 28/02/04 17:26
if you prefer an open-source solution : clamav + amavis-new for
email-scanning
Fairly-Secure Anti-SPAM Gateway Using OpenBSD, Postfix,
- Original Message
From: [EMAIL PROTECTED]
To: [EMAIL PROTECTED] [EMAIL PROTECTED]
Subject: setting up a printer - best method?
Date: 28/02/04 13:51
I've read the handbook on setting up bsd style printers, and i've used
cups some before i started using freebsd. the bsd style
I recently installed Postfix MTA and Courier-Imap. Postfix
is working correctly. I configured Courier-Imap, all seems
well except i get a message when trying to connect from
client saying Fatal error: /home/barry/Maildir: Permission
denied
I have created /usr/local/etcuserdb and run pw2userdb.
I
Hi,
The courier imap program has to be able to reach the location,
it might be that the location you defined, is not reachable
by the user under which imapd runs, (for example imapd runs under
barry-mailserver, and the permissions for /home/barry/Maildir is
700, he is never ever going to access
I am running FreeBSD 5.2.1
I am forever having problems getting my computer to connect with the
internet and each other correctly.
I have three computers - two running WinXP Pro and one running FreeBSD
5.2.1. They are connected to a Netgear Hub, onto a Netgear Router and then
to my cable modem.
I keep getting this error message when I try to run an perl script
from an apache web page that is trying to post an form.
I have mod_perl-1.28 and p5-WWW-Mechanize
Method Not Allowed,
The requested method POST is not allowed for the URL /sim.pl.
Any ideas on how to get this to work?
At 09:29 AM 2/28/2004, fbsd_user wrote:
The requested method POST is not allowed for the URL /sim.pl.
Any ideas on how to get this to work?
Do you have
AddHandler cgi-script .cgi .pl
specified in your httpd.conf file?
Marty Landman Face 2 Interface Inc. 845-679-9387
FormATable DB:
On Sat, Feb 28, 2004 at 09:29:56AM -0500, fbsd_user wrote:
I keep getting this error message when I try to run an perl script
from an apache web page that is trying to post an form.
I have mod_perl-1.28 and p5-WWW-Mechanize
Method Not Allowed,
The requested method POST is not allowed
On Saturday 28 February 2004 02:27 am, DanGer wrote:
i have just upgraded ruby 1.8 and i wanted to run pkgdb and i get
this:
=== Registering installation for ruby-1.8.1_2
=== SECURITY REPORT:
This port has installed the following files which may act as
network servers and may
Hello Good Day list, i am not on the list so please CC me. [EMAIL PROTECTED], [EMAIL
PROTECTED]/
I am looking for a solution, i am trying to multi link 2 modems. Can anyone Refer me
somewhere? i have tryed a program in theports, called mtp, the configuration from the
example is giving me
Thanks for you pointers, they helped me to move further
on into different problem.
I added the addhandler statement and ExecCGI
There are no Limit/Limit at all
The httpd-error.log has these messages now
(2)No such file or directory: exec of /usr/local/www/data/sim.pl
failed
[client ]
Dave Watkins writes:
I've just setup my first IPv6 router following the documentation
here
http://justjohnnyweb.net/~cruisefx/Documents/IPv6/HOWTO_Debian_Masq_IPV6.html
and rather than having a 3ffe:::::/64 number
assigned I have a
I have (at least) three programs - mozilla, OpenOffice, and
javaldx - that occasionally drop something like this:
Feb 27 22:43:29 jerusalem kernel: cmd soffice.bin pid 13002 tried to use non-present
sched_get_priority_max
in the system log.
Now it doesn't seem to be
Quick version - is there any way to compile the php port to get both the
cgi version of the php executable and mod_php, as well as PEAR?
Long version - mod_php is not affected by apache suexec - instead, php
files in the normal document root of the webserver are executed as the
global apache
On Sat, Feb 28, 2004 at 11:11:19AM -0500, JJB wrote:
The httpd-error.log has these messages now
(2)No such file or directory: exec of /usr/local/www/data/sim.pl
failed
[client ] Premature end of script headers:
/usr/local/www/data/sim.pl
The sim.pl file is in that directory and it was
Hi all,
I'm running FreeBSD 4.9-STABLE and I've got the following installed from
ports:
jdk-1.4.2p5
jdk-doc-1.4.2
linux-sun-jdk-1.4.2.02
jikes-1.19_1
which java shows that I am using the native JDK:
$ which java
/usr/local/jdk1.4.2/bin//java
When I do javac test.java, the file compiles fine
Hi,
I recently bought a PS DIMM and memory DIMM's for my HP LaserJet 2100, and
it works fine. But I wonder if it is possible to check the new memory.
I would like to know if I installed all DIMM's correctly and that all
memory is present and usable for FreeBSD.
thanks,
Marco
--
Not Hercules
All ready had sim.pl set as 770 and owner as www and group as wheel
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of Matthew
Seaman
Sent: Saturday, February 28, 2004 11:36 AM
To: JJB
Cc: Marty Landman; [EMAIL PROTECTED] ORG
Subject: Re: run perl scrip with
fbsd_user wrote:
All ready had sim.pl set as 770 and owner as www and group as wheel
The httpd-error.log has these messages now
(2)No such file or directory: exec of /usr/local/www/data/sim.pl
Just a thought - where does your ScriptAlias line in httpd.conf point?
The default is:
On Sat, Feb 28, 2004 at 12:17:34PM -0500, fbsd_user wrote:
All ready had sim.pl set as 770 and owner as www and group as wheel
Ah. Then check the #! line at the top of the script -- it should read:
#!/usr/bin/perl
(possibly with a few flags appended). Make sure you can run sim.pl
from
On Fri, 27 Feb 2004, Shaun T. Erickson wrote:
Warren Block wrote:
It's /boot/loader.conf. See 'man 5 loader.conf'.
Ah. Thank you. :) Where do I find documentation for the 341 or so modules?
Man pages should cover most of them, although you may have to do a
slight variation on the name.
On Fri, 27 Feb 2004, Shaun T. Erickson wrote:
I looked at that. That's not what I mean. :) I mean, if I do not have to
build a new kernel to enable firewalling, logging and divert,
I've always done this with a kernel build. There may be a way to do the
latter two through loadable modules, but
Peter Risdon wrote:
Martin McCormick wrote:
I am trying to modify the execution path on a FreeBSD system
for all the bash2 users on that system. The man page says that
default path is system-dependent, and is set by the
administrator who installs bash.A common
I'm trying to portugrade my system but it fails allways on the same
point : the check for DocBook XML. I did a make deinstall followed by
a make reinstall of that docbook-xml and did the same with docbook-xsl
but nothing seems to get beyond that docbook dtd check... Here is the
output of the
Charles Swiger wrote:
On Feb 26, 2004, at 4:57 PM, Michael Conlen wrote:
[ ... ]
The production system will use dual channel U320 RAID controllers
with 12 disks per channel, so disk shouldn't be an issue, and it will
connect with GigE, so network is plenty fine, now I'm on to CPU.
Sounds
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Hi,
I would take a look onto SSL stuff, having that viossl.o and various SSL and
X509 errors in mind..
But that is maybe a loong shot.. I am going to install 5.2.1-RELEASE today,
maybe I will find something out.. right now all I can offer you is
Hi all,
please, tell me about security of Darkstat. Is it good idea to install it on
firewall/gateway ?
I'd like to measure our company traffic, but I do not have Apache running on
the gateway. How could I redirect Darkstat's output to web-server inside
company ?
Or is there some other tool,
Hello,
I run FreeBSD 4.9 and just ran my weekly CVSup followed by portsdb -uU and
portupgrade -arR. I came across the following message which looks similar
to one previously posted today. I'm relatively new at this and just
question
whether or not the previous response is the same for my
On Saturday 28 February 2004 11:53 am, Bob Perry wrote:
Hello,
I run FreeBSD 4.9 and just ran my weekly CVSup followed by portsdb
-uU and portupgrade -arR. I came across the following message which
looks similar to one previously posted today. I'm relatively new at
this and just question
I had that a similiar problem - it broken portversion. I went and
reinstalled it from the ports and everything is well again - you might
need to do the same as well.
--
-
Rilindo Foster
http://monzell.com
AIM: rilindo
___
[EMAIL PROTECTED] mailing
At 12:43 PM 2/28/2004, Matthew Seaman wrote:
Make sure you can run sim.pl from the command line [snip[ Running
'perl -cw' on the script might be a good idea as well.
I'll second that and add that if you can run fine from the CLI then try
running it as standalone from your browser. If that works
attachment: aba.zip
___
[EMAIL PROTECTED] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to [EMAIL PROTECTED]
Have mod_php installed on apache but it does not have the mhash
extension function.
Where can I find it?
Thanks
___
[EMAIL PROTECTED] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send any mail to [EMAIL
mhash can be found in the ports : /usr/ports/security/mhash
also typing mhash in google gave as first hit the homepage of the mhash.
After installing mhash you need to configure mod_php to use it, checkout the
makefile
for more information.
HTH,
--
Kind regards,
Remko Lodder
Kent Stewart wrote:
On Saturday 28 February 2004 11:53 am, Bob Perry wrote:
Hello,
I run FreeBSD 4.9 and just ran my weekly CVSup followed by portsdb
-uU and portupgrade -arR. I came across the following message which
looks similar to one previously posted today. I'm relatively new at
this
- Original Message
From: [EMAIL PROTECTED]
To: [EMAIL PROTECTED] ORG [EMAIL PROTECTED]
Subject: Where to find apache PHP script mhash function
Date: 29/02/04 04:28
Have mod_php installed on apache but it does not have the mhash
extension function.
Where can I find it?
I am running FreeBSD 4.9. The hauppauge wintv_usb_fm is listed in /usr/src/
sys/dev/usb/usbdevs as being supported; but hauppauge wintv_usb (without the
fm) is not listed. So, it would be my luck to find the latter, but not the
former, in a local store.
Does anyone know if hauppauge wintv_usb
Thanks
I installed the package mhash just now and I had installed the
package version of mod_php.
What makefile are you talking about to get mod_php to use mhash?
-Original Message-
From: Remko Lodder [mailto:[EMAIL PROTECTED]
Sent: Saturday, February 28, 2004 3:44 PM
To: [EMAIL
On Saturday 28 February 2004 12:54 pm, Bob Perry wrote:
Kent Stewart wrote:
On Saturday 28 February 2004 11:53 am, Bob Perry wrote:
Hello,
I run FreeBSD 4.9 and just ran my weekly CVSup followed by portsdb
-uU and portupgrade -arR. I came across the following message
which looks similar
I mean this Makefile
# Instructions on how to enable preferred extensions can be found in the
# Makefile of the master port (lang/php4).
current directory was /usr/ports/www/mod_php4
in /usr/ports/lang/php4/Makefile
snip
.if defined(WITH_MHASH)
LIB_DEPENDS+= mhash.2:${PORTSDIR}/security/mhash
Are you saying there is no way to tell the mod_php
package install to use mhash?
That I have to delete the mod_pgp package and cvsup
the mod_php port config files and them
cd into /usr/ports/lang/php4/ and issue the
make -DWITH_MHASH install clean command?
-Original Message-
From:
Hey there all.
I was looking over the man page for 'wi' and saw that it had the Dlink DWL520 PCI card
listed so I checked local computer parts stores in the area and found a DWL-G520 card.
Are these cards the same as far as being compatible with the 'wi' driver?
Well,
Actually i do, i pasted this from the Makefile,
If i state it correctly, it says that you need to use php4 in
/usr/ports/lang/php4,
if you want to use other extentions, indeed implying that you need to use
that instead
of mod_php for things you want to do,
But i am not sure if there are
On Sat, Feb 28, 2004 at 03:54:09PM -0500, Bob Perry wrote:
Sorry for being so thick, but I get more than just nervous when using
the delete
command. Do I understand you correctly in that I delete, as in rm, the
portupgrade
files in /usr/ports/sysutils/ directory and also all of the ruby
SO you are saying that this /usr/ports/lang/php4 is an replacement
for mod_php?
That it does everything mod_php does plus the extensions can be
added.
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of Remko
Lodder
Sent: Saturday, February 28, 2004 4:30 PM
To:
Hello, fellow FreeBSD users.
My system is so outdated that I can not do a /stand/sysintall anymore.
Not even using 'any'. (Does a work-around exist? That would be a big
help, too.)
I am trying to make Mozilla run with X, which is installed and working.
This machine is kept fairly busy and I
In my opinion yes,
i use the lang/php4 version myself and i have well configured php settings
into my webserver.
Cheers
--
Kind regards,
Remko Lodder
Elvandar.org/DSINet.org
www.mostly-harmless.nl Dutch community for helping newcomers on the
hackerscene
mrtg.grunn.org Dutch mirror of MRTG
Hi
After installing the Antivirus Ports that work good for me, but now i have
one trouble in the Maillog Files from Sendmail, see here (only when the
scanner find a Virus):
Feb 28 22:35:57 mail avmilter[4937]: open(outgoing/df-03109-6647D356) to
stdin failed (Bad file descriptor)
Feb 28 22:35:57
BSDheads,
Im using the first com port (/dev/cuaa0) on my computer with no problems, Im trying to
use the
second com port (/dev/cuaa1) and having problems.
running FreeBSD 4.9-STABLE #0: Mon Feb 9 22:03:10 EST 2004
when I run minicom, I get
[EMAIL PROTECTED] minicom
minicom: cannot open
SO you are saying that this /usr/ports/lang/php4 is an replacement
for mod_php?
That it does everything mod_php does plus the extensions can be
added.
lang/php4 is a master port. You can read lang/php4/Makefile to see what make
definitions that are available (like -DWITH_MHASH). I wouldn't
I have installed FreeBSD before, but it has been a while since I've
messed around with it. I am attempting to install on my secondary
desktop machine which also runs Linux.
ad0s1-ad0s3 are linux partitions as well as ad0s4 which is an extended
partition (containing more linux partitions).
When
Just upgraded to firefox-0.8_4 from firebird. Everything seems fine, but
I can't get horizontal or vertical scrollbars to show up... I can use the
arrow keys to page downwards, but I'd kind of like to have my scrollbars
back. Anyone else seen a problem like this?
--
David Fleck
[EMAIL
I might have missed it in the long amount of FAQ pages.
Is FreeBSD only for 64bit processors. If so can we set up a Donations to
Brach Janney so that he may use our operating system page.
=)
Thankyou for your time.
And here is a place to send any info you might have that is not posted on
the
On Sat, Feb 28, 2004 at 05:56:38PM -0500, Brach Janney wrote:
I might have missed it in the long amount of FAQ pages.
Is FreeBSD only for 64bit processors. If so can we set up a Donations to
Brach Janney so that he may use our operating system page.
=)
Thankyou for your time.
No, it runs on
Hi dude,
FreeBSD is ALSO available for 64bit systems, like AMD64 etc,
but also for normal personal computers. Like the ones i am using
i386 architecture.
So i am sorry but you are not going to have donations to brach janney
:):)
Cheers :)
--
Kind regards,
Remko Lodder
Elvandar.org/DSINet.org
On Sat, Feb 28, 2004 at 04:48:04PM -0600, David Fleck wrote:
Just upgraded to firefox-0.8_4 from firebird. Everything seems fine, but
I can't get horizontal or vertical scrollbars to show up... I can use the
arrow keys to page downwards, but I'd kind of like to have my scrollbars
back.
On Sat, 28 Feb 2004, Kris Kennaway wrote:
On Sat, Feb 28, 2004 at 04:48:04PM -0600, David Fleck wrote:
Just upgraded to firefox-0.8_4 from firebird. Everything seems fine, but
I can't get horizontal or vertical scrollbars to show up... I can use the
arrow keys to page downwards, but I'd
Sorry for being so thick, but I get more than just nervous when using
the delete
command. Do I understand you correctly in that I delete, as in rm,
the portupgrade
files in /usr/ports/sysutils/ directory and also all of the ruby
files in the /usr/ports/
lang/ directory?
No, you can
Hello folks,
I am attempting to build the tiff library, but am continually running into
a problem. After executing `make install` from /usr/ports/graphics/tiff,
the build fails. Included is the exact output of the process, as well as
the 'config.log' as requested.
This is a cleanly installed
Im kinda new at this and
I was compiling my kernel on my Dell Inspiron600m running FreeBSD 5.2
RELEASE when I just remembered[after taking a nap] that I did
#make buildkernel KERNCONF=GENERIC
and I forgot to edit the /usr/src/sys/i386/conf/GENERIC file before
running the process.
anyway, the
Hi dude,
It's not harmfull to replay the whole process,
The way i do it is go to the dir
cd /usr/src/sys/i386/conf/
edit the GENERIC file,
cd ../compile/GENERIC
make clean make depend make make install
the makes sure the next command only get's runned when
the previous command complete
the only problem though with doing it all again is it takes so many hours!!
especialy downloading and make world
is there something i should do before the process to make a backup before
starting? so instead of downloading from the
should i tar the whole /usr/src?
what do you think about this?
i did not mention that you needed to redownload the source
and that you recompile everything
you can just recompile the kernel, in the directories i mentioned
takes some time, but NOT that many time :)
Cheers :)
--
Kind regards,
Remko Lodder
Elvandar.org/DSINet.org
www.mostly-harmless.nl Dutch
On Fri, Feb 27, 2004 at 04:11:31AM +0800, zam4ever wrote:
- Original Message
From: Alex de Kruijff
To: zam4ever
Cc: . [EMAIL PROTECTED]
Subject: Re: BSD Website
Date: 27/02/04 00:51
Do you have these two?:
http://www.oreilly.com/catalog/opensources/book/kirkmck.html
I can connect to my home machines from work using runsocks ssh. Now it
seems to me that I ought to be able to build a full blown VPN tunnel using
this, right?
A little Googling suggest that one approach might be to use ppp over the
tunnel. Given that the 2 machines involved are both FreeBSD
On Sunday 29 February 2004 01:52, [EMAIL PROTECTED] wrote:
Im kinda new at this and
I was compiling my kernel on my Dell Inspiron600m running FreeBSD 5.2
RELEASE when I just remembered[after taking a nap] that I did
#make buildkernel KERNCONF=GENERIC
If you build your own kernel, you should
On Sat, 2004-02-28 at 13:38, beni brinckman wrote:
I'm trying to portugrade my system but it fails allways on the same
point : the check for DocBook XML. I did a make deinstall followed by
a make reinstall of that docbook-xml and did the same with docbook-xsl
but nothing seems to get beyond
On Sunday 29 February 2004 01:39, Remko Lodder wrote:
Hi dude,
It's not harmfull to replay the whole process,
The way i do it is go to the dir
cd /usr/src/sys/i386/conf/
edit the GENERIC file,
cd ../compile/GENERIC
make clean make depend make make install
the makes sure the next
On Sat, 28 Feb 2004, Martin Hudec wrote:
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Hi,
I would take a look onto SSL stuff, having that viossl.o and various SSL and
X509 errors in mind..
But that is maybe a loong shot.. I am going to install 5.2.1-RELEASE today,
maybe I will find
I have looked at the web cvs sources as well as my own form this weeks
current and I would like to know if someone smarter than me could import
the new drivers for agpgart support. I have been running in pci mode
since I bought my board and would like to do some gaming without
windows. I
fbsd_user wrote:
Have mod_php installed on apache but it does not have the mhash
extension function.
Where can I find it?
Thanks
www.php.net/mhash
Kevin Kinsey
DaleCo, S.P.
___
[EMAIL PROTECTED] mailing list
Brach Janney wrote:
I might have missed it in the long amount of FAQ pages.
Is FreeBSD only for 64bit processors. If so can we set up a
Donations to Brach Janney so that he may use our operating system page.
=)
Thank you for your time.
And here is a place to send any info you might have that is
Hi all
I am having a few problems with a FreeBSD gateway machine, as you may have
guessed. A little bit of background info:
I was running 4.8-R-pcan't remember for a long while, all running smooth.
Whilst it was up I had cvsupped to 4.8-R-p18 was it? I think... anyhow, my
brother tripped over
On Tue, 24 Feb 2004 9:32 am, Richard Beyer wrote:
We're currently doing a back up of a FreeBSD 4.9 (2) server by
plugging a USB external drive in and then doing
cp /dev/ad0 /dev/da0
This takes about 30 hours, (USB 1).
Is this the best way to do it, or can someone suggest a better
On Sat, 28 Feb 2004 3:47 am, Derrick Ryalls wrote:
I have a port redirect, public port 5001 to an internal machine
port 3389, for Remote Desktop that works well in natd as long as I
don't fire up my custom firewall:
0005023427286 divert 8668 ip from any to any via sis0
00100 24
I've got Gnome set up as my default GUI on my new DNS
server. (Seems much improved over the older RH8 version.)
But how do I paste things? Clicking with first/third mouse
buttons designate the string or area I want; it should be in
the buffer. But the
I want to NFS share /usr/ports and /usr/src from a master machine for use by
other machines. If I specify -network and -mask options for each share, I get
the error:
mountd[101]: can't change attributes for /usr/src
mountd[101]: bad exports list line /usr/src
but if I don't
This has happened with enough servers at different locations that I have to
believe there is a relationship here. I have servers running the latest
release of MySQL. I've run the servers on FreeBSD 4.4., 4.7, and 4.8. I am
not using the threaded version. On all three versions, on different servers
Tom Munro Glass wrote:
I want to NFS share /usr/ports and /usr/src from a master machine for use by
other machines. If I specify -network and -mask options for each share, I get
the error:
mountd[101]: can't change attributes for /usr/src
mountd[101]: bad exports list line
I read somewhere that they were able to limit CVS pserver connections
to 4 a minute.
I would like to do something similar.
I currently have a firewall/nat box running 4.9-RELEASE-p1, using ipf.
The CVS server is behind the firewall/nat box running on 4.9-RELEASE-p1.
Thanks for any insight you may
What is the latest version of stable? What is the best OSPF and BGP
software. Is Zebra the best. I have been using Gated..
Thanks Dan
___
[EMAIL PROTECTED] mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-questions
To unsubscribe, send
When I try to create a new slice, it gives it the name 'X' which causes
a problem when I try to create new partitions on that slice:
Unable to create partitons on device: /dev/X
This happens when sysinstall runs out of valid slice names.
Try using less file systems per partition...
--
92 matches
Mail list logo
