OK, I missed the part in the original post that said straight, not
right-angle.  Nevermind...

That's going to be a strange looking gizmo when the cables are connected...

Best regards,
Ivan Baggett
Bagotronix Inc.
website:  www.bagotronix.com


----- Original Message -----
From: "Dwight" <[EMAIL PROTECTED]>
To: "'Protel EDA Forum'" <[EMAIL PROTECTED]>
Sent: Thursday, December 19, 2002 2:51 PM
Subject: Re: [PEDA] question about connectors and PCB manufacturers


> Ivan, are you figuring the connectors are right-angle?  The original post
> indicates they are straight, so a cable on one side won't interfere with
the
> cable on the other side.
>
> > -----Original Message-----
> > From: Bagotronix Tech Support [mailto:[EMAIL PROTECTED]]
> > Sent: Thursday, December 19, 2002 8:33 AM
> > To: Protel EDA Forum
> > Subject: Re: [PEDA] question about connectors and PCB manufacturers
> <snip>
> > One other consideration:  is there enough space between the connectors
to
> > actually put mating cables on them?  Separating them by only a PCB
> thickness
> > (0.062 in.) doesn't seem like enough room for the hood/shell of both
> cables.
> >
> >
> > ----- Original Message -----
> > From: "Anand Kulkarni" <[EMAIL PROTECTED]>
> > To: "Protel EDA Forum" <[EMAIL PROTECTED]>
> > Sent: Thursday, December 19, 2002 11:17 AM
> > Subject: [PEDA] question about connectors and PCB manufacturers
> >
> >
> > > Hi everybody,
> > > I have a question about the capability of PCB manufacturers.
> > >
> > > I have a surface mount SCSI connector with 68 pads .
> > >
> > > 050 inch x .100 inch Center - SCSI 3 Compatible - Shrouded
> > Straight -
> > Surface Mount Socket
> > >
> > > example : 2 identical connectors :
> > > _________________________________________
> > > |       _________________________        |
> > > | o    /                         \    o  |
> > > |      ---------------------------       |
> > > -----------------------------------------
> > > Connector 1
> > >
> > > _________________________________________
> > > |       _________________________        |
> > > | o    /                         \    o  |
> > > |      ---------------------------       |
> > > -----------------------------------------
> > >
> > > Connector 2
> > >
> > >
> > > Now this connector has got 2 holes , 1 on each end , apparently for
> > screwing to the board.
> > >
> > > Now, I want to place these connectors on opposite sides of
> > the board.
> > > i.e, one connector on the top surface and the other connector on the
> > bottom surface ;
> > > and I want them be perfectly aligned to each other , as
> > seen in the top
> > view.
> > >
> > > further ,I want to  screw them "TOGETHER" through the board.
> > > i.e, nuts on both the top and bottom surface and the thread passing
> > through the vertically
> > > aligned holes. Again the holes have to be perfectly aligned.
> > >
> > > Also , the pads have to be prefectly aligned.
> > >
>
> >
>

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* To post a message: mailto:[EMAIL PROTECTED]
*
* To leave this list visit:
* http://www.techservinc.com/protelusers/leave.html
*
* Contact the list manager:
* mailto:[EMAIL PROTECTED]
*
* Forum Guidelines Rules:
* http://www.techservinc.com/protelusers/forumrules.html
*
* Browse or Search previous postings:
* http://www.mail-archive.com/proteledaforum@techservinc.com
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

Reply via email to