Hi all.
I have decided to leave this list.
You all take care.
Mickey
[Non-text portions of this message have been removed]
To listen to the show archives go to link
http://acbradio.org/handyman.html
or
ftp://ftp.acbradio.org/acbradio-archives/handyman/
The Pod Cast address for the Blind
Sequential.
- Original Message -
From: Robert J. Moore
To: Blind Handyman
Sent: Thursday, April 12, 2007 12:41 PM
Subject: [BlindHandyMan] GRAND AM Motor?
On the top of the motor is stamped,
3100 S F I v6. What does S F I stand for I would think the F I stands for
Robert,
I know that there are online subscription services for service manual type
information. They cost a subscription fee and are really geared toward those
who do a lot of work on cars. I don't know if any of them are accessible to the
blind.
To answer your specific question, I don't know
Unfortunately, marking lines, or rather scribing them, really doesn't work very
well for a blind guy. A blind guy needs to either use some variant of the
method that Dale described or make a simple jig to position the hinges, to hold
them in place while the screws are installed.
The jig can
When viewing the face of the receptacle from the front and the round ground
hole down, the black (hot) wire is on the right and the white (neutral) wire is
on the left. There is a difference in the length of the flat slots on the
front of the receptacle, also. If the receptacle is still
by what you give
On Tue, 10 Apr 2007, Mickey Fixsen wrote:
When viewing the face of the receptacle from the front and the round ground
hole down, the black (hot) wire is on the right and the white (neutral) wire is
on the left. There is a difference in the length of the flat slots on the front
Do you know if they have a web site? If so, what is the address?
Thanks.
- Original Message -
From: Tom Fowle
To: blindhandyman@yahoogroups.com
Sent: Wednesday, April 04, 2007 4:48 PM
Subject: [BlindHandyMan] Talking MultiMeter, another source:
All,
Just found that the
Ok. Thanks.
- Original Message -
From: Tom Fowle
To: blindhandyman@yahoogroups.com
Sent: Thursday, April 05, 2007 1:45 PM
Subject: Re: [BlindHandyMan] Talking MultiMeter, another source:
Looks like
http://www.mpja.com
is it, lots of cool electronics stuff.
Seen
It is not often that measuring tools designed for the sighted can be easily
used by a blind person. The following gauges were designed for the sighted,
but work great for a blind person. They have print markings on them, but you
don't have to be able to read the markings to use the gauges
The main advantage to the Shopsmith is its compact size. The machine itself
does not take up a lot of space, but you do need storage space for all the
attachments.
I have known several people who have had these machines over the years. They
say they are well made.
The biggest downside to
Robert,
Yes, there such kits. You will probably have to go to a machinists supplier to
find them.
Some guys will weld a nut on a stud, if there is enough room. The heat of the
welding also helps break the frozen stud.
Good luck.
- Original Message -
From: Robert J. Moore
Hi.
I was at Lowes yesterday to pick up a few things and look at some others. I
looked at the Bosch PS20 driver. It has gotten some great reviews in the
magazines. It is small, pistol shaped and powerful. the price on it was $129.
I picked one up and to my surprise, it rang up at $109.
.
Thanks,
Keith
-Original Message-
From: blindhandyman@yahoogroups.com
[mailto:[EMAIL PROTECTED] On Behalf Of Mickey Fixsen
Sent: Saturday, March 24, 2007 8:04 AM
To: blindhandyman@yahoogroups.com
Subject: Re: [BlindHandyMan] Pocket hole jigs.
Hi Keith.
Did you buy the Kreg
really am looking forward to making pocket holes.
Thanks,
Keith
-Original Message-
From: blindhandyman@yahoogroups.com
[mailto:[EMAIL PROTECTED] On Behalf Of Mickey Fixsen
Sent: Wednesday, March 14, 2007 11:26 AM
To: blindhandyman@yahoogroups.com
Subject: Re: [BlindHandyMan
Does the unit sit firmly on the floor? If it does, then I don't see how
adjusting the feet will help anything.
I wonder if a piece of clothing got outside the inner tub, or if something
on the suspension system has broken or come loose.
- Original Message -
From: David Engebretson
I have been using 2 different models of the Kreg pocket hole tools for years.
They are quality tools and well worth the price. As long as you have made good
cuts on the boards, the pocket holes make very tight, strong joints. These
tools are easy to use with very little learning curve.
You
These are special screws designed for use in pocket hole applications. Most
suppliers that sell the tools also sell the screws.
- Original Message -
From: Dan Rossi
To: blindhandyman@yahoogroups.com
Sent: Wednesday, March 14, 2007 1:45 PM
Subject: Re: [BlindHandyMan]
Subject: RE: [BlindHandyMan] Pocket hole jigs.
Are these screws sold in the big box stores like Home Depot and Loes? I
have always wanted a pocket hole jig.
Thanks,
Keith
-Original Message-
From: blindhandyman@yahoogroups.com
[mailto:[EMAIL PROTECTED] On Behalf Of Mickey
Subject: Re: [BlindHandyMan] Pocket hole jigs.
pardon my ignorance but cud i use it for mounteing a table topon to a frame ?
how wud i doe this drill the pocket and crew down threw the frame and into the
under side of the table top?
- Original Message -
From: Mickey Fixsen
I have used a bit of WD-40 for this exact purpose.
- Original Message -
From: Keith Patterson
To: Blind HandyMan
Sent: Tuesday, March 13, 2007 7:33 PM
Subject: [BlindHandyMan] Lubricating a light socket?
Can one lubricate a light socket?
I have a ceiling fan that uses
I have made Braille tags in both thin brass and thin sheet metal by putting the
metal in a slate and use an automatic center punch to punch the dots. I would
think a pperson could use this method and then drill out the punch marks to
make flexible Braille cell templates. It would be a bit
Patrick,
I can't imagine how a valve cover gasket could possibly make this noise. I
would have another shop take a look at it. Any technician worth their salt
could find the source of the noise. The hard ones to find are intermittent or
deep inside the engine and I seriously doubt if your
Hi list.
I have some specific questions regarding the Texas Commission for the Blind and
whether or not they have a woodworking shop. If anyone on the list can answer
a few questions regarding this, please contact me off list.
Thanks-- Mickey
[EMAIL PROTECTED]
[Non-text portions of this
Larry,
I don't recall reading another reply to the original post, but you could check
out the archive and see if it is there.
http://www.mail-archive.com/blindhandyman@yahoogroups.com/
Mickey
- Original Message -
From: [EMAIL PROTECTED]
To: blindhandyman@yahoogroups.com
You can use isopropyl alcohol on a scotchbrite pad. Rinse the pad often and
then finish with paper towels to dry the rollers and remove any small film
residue.
Good luck
- Original Message -
From: Tom Huhn
To: blind
Sent: Thursday, February 22, 2007 9:15 PM
Subject:
are the uses for each?
--
Larry Martin
Woodworking for the Blind
--joining the world of blind wood workers
-- Original message --
From: Mickey Fixsen [EMAIL PROTECTED]
You can use isopropyl alcohol on a scotchbrite pad. Rinse the pad often
I don't understand this at all. How does this work?
Mickey
- Original Message -
From: Lenny McHugh
To: Handyman-Blind
Sent: Tuesday, February 20, 2007 10:45 AM
Subject: [BlindHandyMan] CONVERT YOUR TABLE SAW INTO A PRECISION JOINTER
MACHINED ALUMINUM DISC CONVERTS YOUR
Ok, thanks. I understand how this makes the sanding disk only sand at one
small location on the edge of the board. I still don't understand how this
turns the table saw into a jointer. A jointer straightens and squares two
adjacent faces of a board to each other. If you use the rip fence to
John,
Here are a couple of my thoughts and I will be making a few assumptions to make
them. First of all, I hope that when you refer to the 2 vertical pieces, you
are referring to the 2 pieces that will make up the top and you really meant to
say horizontal instead of vertical. I will assume
It sounds like your belt slipped and wore a divit in it. Now, each time it
goes around, the divit makes a bang.
- Original Message -
From: bill holton
To: blindhandyman@yahoogroups.com
Sent: Friday, February 16, 2007 3:47 PM
Subject: [BlindHandyMan] Drier duldrums
A
great job.
You've got the measuring and jig thing down better than I. But that
raising the unit trick felt familiar.
Might one ask what it cost?
Does this place ship or have an on-line catalog?
On Tue, 6 Feb 2007, Mickey Fixsen wrote:
Hi.
I just recently bought a Delta 50
Dan,
Shop around at local Delta dealers and see what you can find for price. If it
shows up at their business damaged, you won't have to deal with returns.
Besides, you might be able to buy it locally for about the same price and not
have to pay for the shipping and handling or be near the
.
-Original Message-
.From: Mickey Fixsen[EMAIL PROTECTED]
.Sent: 2/6/07 1:44:49 PM
.To: blindhandyman@yahoogroups.comblindhandyman@yahoogroups.com
.Subject: Re: [BlindHandyMan] whole shop air filter installation
.
.Dan,
.
.Shop around at local Delta dealers and see what you
Maybe you should consider gluing and nailing a good plywood underlayment before
you install the hardwood.
- Original Message -
From: Dan Rossi
To: BlindHandyman@yahoogroups.com
Sent: Sunday, February 04, 2007 9:27 PM
Subject: [BlindHandyMan] Which way to lay?
OK,
I
You Don't have to replace the floor unless it's a hazard. You might want to
fill the crack, though. You should use a flexible concrete crack filler. A
self-leveling, flexible crack filler would be best. The best one that I know
of is called SL1 and is available through concrete or masonry
Hi Larry.
No, screen readers will not read the varification letters/numbers that must be
entered into an edit field. One must either use a sighted person to read the
characters that appear on the screen, or some web sites have set up a link to a
customer service person to help do the job.
This must be a pretty small vise, right?
17/64 is just 1/64 larger than 1/4. Therefore, you can go to any good
hardware store and buy a long grade 5 bolt for the handle. You could buy a 5
long bolt, for instance. The bolt will only have about 1 of threads on it and
the rest of the shank
Yes, you should be concerned. It sounds like you have insufficient
electricity. This could be due to a bad connection, corroded or partially
broken wire, or several other things. Call your power company to come check it
out.
- Original Message -
From: sarah derr
To:
An easy way to make dados on opposite sides of a cabinet line up when using a
router to make the dados is to clamp them together so that one setup for a
particular dado does them both at the same time. For example, you would lay
both sides on a bench with the inside faces of the side facing up
Ralph,
Jigs like the ones described are great for transfering measurements, but they
are not for determining a particular measurement. For instance, if you need a
board that is 27-1/4 long for a project, you need a device that is marked with
ruled markings to measure the board to be cut. The
Many of them have a plug on the body of the tool that you remove and fill with
oil. If yours does not have this, just add a couple of drops in the air hose
connection each time you get it out to use it. Don't over oil it or you will
always have a mess on your hands.
- Original Message
Phil,
If you have one of the C-1 cassette players made by Telex and used as the donor
players from NLS, there is a very easy way to get to the heads. There is a
removable plate between the buttons and the cassette door. To remove it, you
will find a small square hole on each side of this
that plate gives one access to lining the heads but not the
actual surface of the head.
Phil Parr.
- Original Message -
From: Mickey Fixsen
To: blindhandyman@yahoogroups.com
Sent: Sunday, January 14, 2007 8:13 AM
Subject: Re: [BlindHandyMan] Head cleaning.
Phil,
If you
The clicking sound is the light relay switching on and off with the
resulting blinking of the light. There is no clutch. This was not what was
described in the original post. He simply said the motor runs, but nothing
happens.
- Original Message -
From: rj [EMAIL PROTECTED]
To:
I guess we diagnosed it correctly. Sounds like you got a very good deal on
the repair.
Congratulations!
- Original Message -
From: brice mijares [EMAIL PROTECTED]
To: blindhandyman@yahoogroups.com
Sent: Friday, January 12, 2007 6:50 AM
Subject: [BlindHandyMan] garage door is fixed
Sounds like a nice project. I was just curious, because you didn't specify.
Are you using Western Red Cedar, or Aromatic Cedar?
Good luck with it.
- Original Message -
From: Dan Rossi
To: BlindHandyman@yahoogroups.com
Sent: Friday, January 12, 2007 10:17 AM
Subject:
Actually, that sounds like Western Red Cedar. Aromatic cedar is much harder
wood.
Good luck with your project.
- Original Message -
From: Dan Rossi
To: blindhandyman@yahoogroups.com
Sent: Friday, January 12, 2007 12:32 PM
Subject: Re: [BlindHandyMan] Cedar closet project.
If the motor starts and runs, then a reset button won't help. If the motor
runs, but the door does not move, then something in the drive unit is either
slipping or has stripped a gear. I know some old screw drive openers used a
clutch mechanism that could slip, but I don't think any use it
Thanks for confirming that my investment in my tool collection was well placed.
It is always good to know that I haven't wasted the money and that I am using
the tools correctly!
- Original Message -
From: Geoff Eden
To: blindhandyman@yahoogroups.com
Sent: Wednesday,
Ok, I'm sure this is perfectly clear to you as the author, but it makes
absolutely no sense to me and I've been doing this stuff for over 40 years.
Are you simply suggesting that it is a good practice to clamp your work on
saws, if at all possible?
- Original Message -
From:
The threaded piece is the primary measuring device. The rectangular nut is the
measuring nut and the hex nut is the locking nut. Here is how to use it.
There is a small hole in one end of the threaded rod. This hole is where the
extensions attach to the threaded rod. Rotate the rectangular
The most accurate way is with a dial indicator and the help of a sighted person
to read the dial indicator. You will never get it with a Clickrule. It just has
too many problems that make an extreme accurate measurement impossible. You
could get a ton closer with a Rotomatic, but it still is
They aren't very friendly for use by a blind person. They really need to be
used with a jig by a blind person. The rotary action of the cutter makes the
tool want to pull strongly in one direction.
It might work for you, but it would depend on the task you want to perform.
Without knowing
made up buy
gluing planks to gether so the end is level any other ideas? I don't have a
table I was thinking about a trim saw or a circular saw with a inch blade
- Original Message -
From: Mickey Fixsen
To: blindhandyman@yahoogroups.com
Sent: Tuesday, January 09, 2007 6:23 PM
It is advantageous to use a plunge router for this application. Removing the
counter balance springs is a real advantage for a router that is dedicated for
use in a router table. This makes height adjustment a breeze. Make sure it
will use both 1/4n and 1/2 shank router bits. Find one that
Use 1/2 wide teflon tape. Wrap it around the threads holding the tape edge
flush with the beginning bottom threads of the fitting. Rotate the fitting
in the direction that you would to install it and keep tension on the tape
so that it is quite tight on the threads as you rotate. Make about
What an outrageous waste of time and money!
- Original Message -
From: Don
To: blind handy man
Sent: Thursday, January 04, 2007 9:27 PM
Subject: [BlindHandyMan] Off topic one time post.
The following message will be a one time o t post for handy man. I don't want
a
John,
They do not have a web site that I know of. The CD's that are sent contain
files in MP3 format that will play in any CD player that can play the MP3
format. They can be played on a computer by simply putting in the CD drive and
then clicking the file that you want to listen to.
They
Do you know something that I should be aware of?? Ha!
- Original Message -
From: Tom Huhn
To: blindhandyman@yahoogroups.com
Sent: Thursday, December 21, 2006 9:45 AM
Subject: Re: [BlindHandyMan] How to Build a Coffin
I was doing a search for cabinet plans awhile
It is very unlikely that the light switch will have a neutral wwire in the box.
It is very likely just a switch drop coming down from the light fixture. Of
course, this depends on how they ran the wiring. If they ran the wiring from
the panel up through the switch and then on to the light
I have never found these types of tools in a porn shop. I don't think I would
ever buy used tools and equipment in a porn shop!!! ROFL!!!
- Original Message -
From: [EMAIL PROTECTED]
To: blindhandyman@yahoogroups.com
Sent: Friday, December 22, 2006 2:20 PM
Subject: Re:
I have 2 audible stud finders. They are both made by Zircon and called Stud
Sensor. One is a basic model that emits an audible tone. The other one will
do 3 functions-- find studs, find pipes, find electrical wiring. They both
work well on drywall and paneling walls. They do not work good
I found this to be an interesting post.
However, since this is a list for the blind and how to do things as a blind
person, I don't see one single thing that tellls a blind person how to do this
job. It may be an exercise in accurate information that serves noone.
- Original Message
You can use toothpaste on a soft cloth to buff out white water rings.
- Original Message -
From: Ray Boyce
To: blindhandyman@yahoogroups.com
Sent: Monday, December 18, 2006 10:49 PM
Subject: [BlindHandyMan] Removing Water Spots and Rings from Furniture
Hi
Removing
It should not be harmful. I wouldn't eat it, however.
- Original Message -
From: tunecollector
To: blindhandyman@yahoogroups.com
Sent: Tuesday, December 12, 2006 12:52 PM
Subject: [BlindHandyMan] microwave the paint
Is it dangerous when the enamel paint chips off on the
Here is the way that I think of this.
The hot wire from the panel (black wire) connects to the odd terminal on switch
#1. The hot (black) wire that goes to the light fixture, connects to the odd
terminal on switch #2. There are 2 wires that simply connect between the other
2 terminals on the
There is a clock supply that has all sorts of clock movements. They have one
that is designed to run backwards. I don't think it has a pendulum, but they
sell a seperate pendulum device that could be used in conjuction with the
movement. Here is their information.
Klockit
N3211 County Rd. H
Hi.
I know a guy who has full vision and just got the ends of 3 fingers cut off in
the dado blade of a table saw. It went down to the first knuckle below the
finger nail. He has used one of these saws for years and is very experienced
with them. It is a very nasty injury and it is healing
Unfortunately, I don't think you will find a suitable product for this job.
Even most epoxy compounds will not effectively bond to plastics, especially in
this application. We've tried numerous products over the years for repairing
smaller cracks on these radiators than you have, without
They don't work very well for this application. There just is not enough
surface area on the wire to allow the color identifier to see the proper color.
- Original Message -
From: Tom Huhn
To: blind
Sent: Friday, November 24, 2006 11:04 AM
Subject: [BlindHandyMan] color
Bill,
While you are at the hardware store, why don't you pick up a selection of
various size screws and bolts so that you can label them and use them for
future reference. Maybe, you could pick up a selection of screws from #4
through #12 and a selection of bolts from 3/16 (also a #10)
One word of serious caution here. Do NOT use this General purpose RTV sealant
from caulking gun tubes on any computer controlled engine that uses an oxygen
sensor. You MUST use automotive RTV sealant that is specifically designed to
be safe for oxygen sensors. Anything else will kill the
Robert,
The first thing one needs to know is how the engine is to be used. There is a
huge difference on how the engine components are combined to work together from
a street motor to a race motor. Remember that it is the combination of all
components of the engine, transmission, rear gear
First of all, it sounds to me like you have a poorly designed system. Good to
hear that you are planning on redoing the system in the near future. A good
plumbing and heating person should be able to correctly solve your problems.
To answer this one specific question: Yes, you can get a
What part of the system is not heating?
Are you sure there aren't any thermostatic control valves on the part of the
system that is not heating? If there are, they could be faulty or set to the
wrong temperature.
- Original Message -
From: mark
To:
You got gas inside the crankcase of the engine when you turned on the key
without the gas lines hooked up and this vehicle has an electric fuel pump. It
went down through the oil drains in the heads, because the valve covers were
not installed. Not exactly sure what set off the accumulated
This is very good information using blind techniques. it should be put on the
files page for future reference.
We could use a lot more like this.
Thanks
- Original Message -
From: R S Enterprises
To: blindhandyman@yahoogroups.com
Sent: Friday, October 27, 2006 1:38 PM
John,
Kudos to you for your project!
All I have to add is that I NEVER get my fingers that close to the saw blade.
One rule that I never break on my table saw is: If the work is between the
miter slots and the blade, I ALWAYS use push sticks.
Congratulations to you!! Be careful.
-
Some of the filters have some sort of reinforcement on one side of them. This
could be a net mesh, cardboard bars, wire or plastic egg crate. If there is
some sort of extra reinforcement on one side that is not on the other, this is
the discharge side of the filter (toward the furnace
Sorry, not a real answer to your question.
What do they say?
Danger!! Get the hell out of here!!
Again, sorry, but I just couldn't help myself.
- Original Message -
From: Rob Monitor
To: blindhandyman@yahoogroups.com
Sent: Wednesday, October 25, 2006 4:32 PM
Subject:
Lewis,
I read with great interest, your 2 posts on how to carve an eagle. I found the
descriptions very fun to read and could follow along pretty well. I really
applaud your skills with chain saws.
What I found missing, however, was how you do this as a blind guy. I use chain
saws, quite
Dale,
You need to put something heavy on the base to keep the stands in place (sand
bags, or something). As long as the board contacts the upper half of the
roller and the stand is secure enough to stay put, the board will go over the
top. I set the height by placing a long board on the tool
David,
I own 2 leaf blower/vacs. The oldest is a Sears Craftsman gas powered unit.
It is about 12 years old. I find that it is quite heavy and the blower
works ok, but not great. I hate the vacuum arrangement on it and never use
it.
Last spring, I bought a Toro electric model blower vac.
Hi Lewis and welcome.
I have done some electric welding with a stick welder with satisfactory
results. A while back, I asked the list if anyone knew how a blind guy could
MIG weld. The answers were not encouraging. There didn't seem to be anyone
who knew the techniques and steps for a blind
Ed,
The Clickrule comes with 3 12 extensions and will measure up to a total of
48. It costs $65 plus sh from the NFB store.
The Rotomatic comes with 3 extensions. 1- 6, 1-- 12, and 1- 18 and will
measure up to a total of 42. The price from the NFB store is $50 plus sh.
- Original
Lee,
There used to be a place here that rented service bays for you to work on your
car. It was about 30 years ago. The problem, these days, is that the
liability insurance makes this prohibitive.
It would be great if we had such a place where every tool we could ever dream
of using would
Tom,
Another thing to check is the short piece of pipe that screws onto the big
drain piece in the sink. This pipe is called the tailpiece and screws onto the
drain basket with a fine thread. this fine thread should have a bit of pipe
thread sealant on it and it should be screwed up tight to
There are none of those around here.
Do you think they would have a coronary if they had a blind guy show up and
want to use the shop?
- Original Message -
From: John Schwery
To: blindhandyman@yahoogroups.com
Sent: Thursday, October 19, 2006 7:51 AM
Subject: Re:
Richard,
It would be helpful if you can tell us what type of water heater you have. (eg.
electric, gas with a pilot light, gas with electric power vent, etc.) The
answer will depend on the type of water heater, since the reset button is
different for each type. I will assume that it is not a
, Mickey Fixsen wrote:
electric
Richard Most
[EMAIL PROTECTED]
[Non-text portions of this message have been removed]
--
No virus found in this incoming message.
Checked by AVG Free Edition.
Version
Rob,
There really is not a better. As others have said there is an accuracy
difference. They both have their advantages and disadvantages.
The Clickrule is faster to adjust than the Rotomatic to get your measurement.
The Clickrule will do inside measurements more easily than the Rotomatic
Thanks to all who replied to this issue.
As expected, the responses are extremely varied. If nothing else, it has been
interesting.
Keep all of the good blind tricks and techniques coming.
- Original Message -
From: Mickey Fixsen
To: Blind Handyman
Sent: Tuesday, October
I listened to the Handyman show of last week and Don said he was very familiar
with and used a circular saw guide from Sears called the Craftsman Accu-rip saw
guide. He said that it would take sighted assistance to set it up the first
time and get it adjusted to the zero point. He went on to
Message -
From: Don
To: blindhandyman@yahoogroups.com
Sent: Wednesday, October 18, 2006 5:18 PM
Subject: Re: [BlindHandyMan] blind techniques
Mickey, if you don't like the list unsubscribe, just get the hell out...Don
- Original Message -
From: Mickey Fixsen
[EMAIL PROTECTED]
Skype DaleLeavens
Come and meet Aurora, Nakita and Nanook at our polar bear habitat.
- Original Message -
From: Mickey Fixsen [EMAIL PROTECTED]
To: blindhandyman@yahoogroups.com
Sent: Monday, October 16, 2006 5:36 PM
Subject: Re: [BlindHandyMan] Adventures
Bill,
Congratulations!!!
I'm sure that you noticed on coats after the first one, that you don't have to
use as much finish and it can be rubbed out further. Btw, I use 400 grit
sandpater between coats and be sure to make sure that everything is very clean
before applying the next coat.
Yes,
Tom,
No, I have not worked with Spirit Varnish.
You can dip the dowel ends in the can if you wish, but you will have way too
much on them when you pull them out and they will drip all over and you will
have to deal with it anyway. I usually just give end grain a bit more
attention when I am
Tom,
This is an excellent example of how the sighties don't know didly!
You can do exactly what you had in mind with excellent results. As a matter of
fact, you will do better than your wife with a brush.
Spar varnish is an alkyd varnish with a ultraviolet inhivitor. In real speak,
this
: Re: [BlindHandyMan] tiny shutoff valves
Try the pet stores.
Ken
- Original Message -
From: Mickey Fixsen [EMAIL PROTECTED]
To: blindhandyman@yahoogroups.com
Sent: Wednesday, October 11, 2006 10:26 AM
Subject: Re: [BlindHandyMan] tiny shutoff valves
I tried all
.
- Original Message -
From: Mickey Fixsen [EMAIL PROTECTED]
To: blindhandyman@yahoogroups.com
Sent: Thursday, October 12, 2006 10:55 AM
Subject: Re: [BlindHandyMan] tiny shutoff valves
Thanks for the suggestion. I've tried this source and the valves are too
large for my
1 - 100 of 125 matches
Mail list logo
