On Tue, 21 Jul 2009 09:29:18 -0700, Mike Scott wrote:
What has happened to the frequent K3 beta updates and all the
chatter that accompanied them? I haven't kept up with the list very well
but have noticed that content seems to be missing these days.
Wayne went on a 3-week vacation :)
The Gurus must be working on some massive release of new firmware :-)
Stewart G3RXQ
On Mon, 20 Jul 2009 12:21:57 -0500, sr...@swbell.net wrote:
What has happened to the frequent K3 beta updates and all the
chatter that accompanied them? I haven't kept up with the list very well but
I have it on my K3. Slight, but noticeable.
Stewart G3RXQ
On Sun, 12 Jul 2009 23:13:50 -0400, Terry Price wrote:
Has anyone else noticed some distortion using the tx gate
option? I heard it
on a friends' K3 and tested it on mine, while listening on
headphones and
the monitor on, after each
My late parents spent an entire week looking for a trapped bird in their house.
A neighbour found the smoke alarm birdie :-)
73
Stewart G3RXQ
The only beep-beeping I've come across has been laptop PCs left on standby
warning that their batteries are about to run down. I think some mobile
I agree.
The cost of the K3 filters is now so high in the UK, that I want to
get away with the minimum number necessary.
73
Stewart G3RXQ
On Thu, 9 Jul 2009 10:00:42 -0400, Joe Subich, W4TV wrote:
I wonder if there is any possibility of allowing AM TX and/or
ESSB via the FM filter...
It is
Yes, I too had the feeling that this used to work.
Stewart G3RXQ
On Fri, 19 Jun 2009 22:42:52 -0700, Brett Howard wrote:
I should also state that I swear this was just working a minute
ago and
now I seem to always get SUB N/A unless both VFO's are on the
same band.
On Fri, 2009-06-19 at
I agree, whatever algorithm BHI uses, it really works.
73
Stewart G3RXQ
On Wed, 29 Apr 2009 16:05:07 -0500, Bill NY9H wrote:
I have two Hear-it speakers from England's BHI company hooked
thru
my microham controller's headphone outputwhich is connected
to
the 7800 the K3.
With a low-
That's my view as well.
Stewart G3RXQ
On Sun, 5 Apr 2009 17:09:08 -0400, Steve Ellington wrote:
Perhaps the band noise is more obvious in the K3 because the low frequency
audio is restricted causing the noise to be distributed over a more narrow
range. This lack of bass tends to induce for ear
A catcha to be aware of if you are building kit that uses DIL plugin relays.
Some of these relays have diodes already fitted internally across the coil.
I have built a couple of projects on PCB's, and wondered why the relay would
not operate.
Reversing the coil connections got things working.
73
Spent a few hours in WPX SSB, but gave up as power levels from my K3 were all
over the place.
My linear did not appreciate the wild input power swings. Back to the bad old
days.
Using the latest beta. Hope this problem gets fixed soon.
73
Stewart G3RXQ
Hi Dave,
No it's not the spike problem.
I think that it is close to the tune then creep up in power issue.
It only seems to be a problem when the KPA3 is selected.
The power output on either a whistle or using the 2 tone oscillator is low on
SSB, and
hitting the key puts the power back up.
Ugh !
Just booked an Alaskan cruise...
Do we need to take hard hats ?
73
Stewart G3RXQ
On Sat, 28 Mar 2009 12:59:40 -0400, ron wrote:
Jim Wiley wrote:
This is very OT, to be sure, but perhaps interesting to some of
you:
For those of you who haven't already discovered this, there
are some
On Sun, 8 Mar 2009 15:22:39 -0700, wayne burdick wrote:
You would have to use the AUX RF input for the sub RX in this case
(because the MAIN path is connected to the transverter IN jack on the
KXV3). Hold BSET, then tap ANT to switch the sub from MAIN to AUX.
AUX can be either the
I don't know if I am trying to do the impossible, wanting to
listen on 2m and 80m simultaneously.
I have a homebrew 2m transverter connected via the KXV3 with a
28MHz I/F setting.
If I set up 2m on Main RX , then I cannot get anything out of the
Sub RX when set to 80m.
If I set up 80m on
Having just completed a home brew 144MHz - 28MHz transverter, I
thought that I would set the K3 scanning to monitor repeater
output frequencies.
Although I have used scanning successfully on other bands, all I
get is Scan N/A.
What am I doing wrong ?
73
Stewart G3RXQ
I have been busy setting up MMVARI together with N1MM to use in
RTTY contests. I have not encountered any real problems, however I
am a little confused when it comes to using the K3 in the AFSK A
mode.
I am using this mode because it always has the RTTY LSB selected
as default. The audio
Hi Lyle,
Thanks for your reply. A bit more investigation shows that
switching between AFSK A, DATA A, USB or LSB makes no difference
as far as the frequency offset is concerned.
What does make a difference is switching between Digital mode and
CW/SSB in N1MM...
In non Digital Modes the K3 VFO
Jim,
I have mine hard connected the way you describe and it
communicates OK with my K3 at 38.4kB with KENW mode.
As has been said before AUTO INF=1 and SteppIR in General Mode.
73
Stewart G3RXQ
On Mon, 9 Feb 2009 12:37:42 -0500, Jim Spears wrote:
I should have pointed out that the specific
Does it for me as well.
A very useful program.
Stewart G3RXQ
On Fri, 6 Feb 2009 06:18:36 -0800 (PST), Lee Buller wrote:
While exploring the Elecraft site, I discovered K3-EZ Software
by Bill Coleman. See it at:
http://home.roadrunner.com/~n2bc/SW.htm
Now, I have no vested interest in the
to try.
73
Stewart G3RXQ
On Tue, 3 Feb 2009 17:54:28 GMT, Stewart Baker wrote:
Is it me, or is the Elecraft site very slow to load.
At present it is a bit like kick starting a Snail.
Stewart G3RXQ
__
Elecraft mailing list
Home
I am now able to get fast access the Elecraft site.
Back up to Warp Factor 10...
Don't know why this is, must be the snow melting !
73
Stewart G3RXQ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Is it me, or is the Elecraft site very slow to load.
At present it is a bit like kick starting a Snail.
Stewart G3RXQ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Dear Kjeld,
You don't say what modes you are intending to operate.
I have removed all the extra filters from the list as I have found
the standard filter offering from Elecraft to be up to the job on
both SSB and CW. However, you might consider adding a 400Hz filter
for CW if that is your main
-
From: Stewart Baker [mailto:stew...@baker.nildram.co.uk]
Sent: 2. februar 2009 17:16
To: Kjeld Holm; elecraft@mailman.qth.net
Subject: Re: [Elecraft] [K3] K3 owner in spe
Dear Kjeld,
You don't say what modes you are intending to operate.
I have removed all the extra filters from the list
Hi,
Recently I have been trialing K3_EZ software from Bill N2BC.
Its features include: Band stack Registers, Frequency Memories, an
Equalizer Manager and a Configuration Helper.
Great software, well worth a look..
73
Stewart G3RXQ
___
Elecraft
Hi Barry,
Do make sure that BOTH connectors between the Front Panel and DSP
boards are mated. If you have the connector with the single row of
pins out of it's socket then the Front Panel mic socket will not
work.
So far, I have managed to achieve this TWICE !
73
Stewart G3RXQ
On Thu, 22 Jan
We're getting closer !
I see that the latest Errata for the KRX3 manual (12/1/09)
includes operating instructions for when the Main and Sub
receivers become fully independent .
Maybe there should be a day named after the event... :-)
73
Stewart G3RXQ
Mike,
Make sure that BOTH connectors between the front panel and DSP
boards are mated. If you leave the one with the single row of pins
unmated you will get the problem of the front mic socket not
working.
Trust me - I have done this TWICE !!!
73
Stewart G3RXQ
On Mon, 12 Jan 2009 15:18:38
I need a little more RF tickling the spider's legs to get them to
move off the open wire feeder :-)
Stewart G3RXQ
On Sat, 03 Jan 2009 21:22:49 -0500, p...@n4lcd.com wrote:
I always use 5W, ... when I tune up my external ATU.
I have my K3 set to use 0.2 Watt for tuning my external LDG
tuner as
No problem Wayne.
I always use 5W, and the LP-100A when I tune up my external ATU.
73
Stewart G3RXQ
On Fri, 2 Jan 2009 10:01:08 -0800, wayne burdick wrote:
Stewart Baker wrote:
The K3 output was from ANT1 using the internal ATU. The ATU was
automatically tuned to 1:1 on all bands
I would consider that figure acceptable.
With my K3 the isolation between ANT1 and ANT2 is 42dB worst case,
56dB Max.
Moving the single wires around made no difference. I suspect that
the level of isolation is determined by the ATU PCB layout.
Given the size of that board I think that the
On Sat, 3 Jan 2009 07:34:13 -0600, Phil Debbie Salas wrote:
I always use 5W, ... when I tune up my external ATU.
Actually, I use 15 watts for tuning both the internal K3 tuner,
as well as
my external MFJ-998 tuner. I do this for two reasons:
1) I get much better SWR agreement between 15
On Sat, 3 Jan 2009 08:58:57 -0600, Phil Debbie Salas wrote:
Hot switching RF in an external ATU is not to be recommended
for
any radio at any level.
BUT - you DO hot-switch your K3's RF output when using any
relay-based
auto-tuner, including the internal K3 auto-tuner. So my
reasoning is
This thread came at the right time. I have just finished
re-calibrating my LP-100A. I did this after having used the unit
for 6 months, however the calibration was very close to the
original settings.
Then I thought that I would check my K3 SWR indication.
The results are not as good as I would
On my K3 there is still quite a loud speaker 'pop' with Power On
and Off after loading firmware revision 2.76.
Looking at the NS data sheet for the audio amplifier IC shows that
it has click suppression built in. The length of the suppression
period is determined by the value of the capacitor on
I got fed up with the felt hiss, so I made a couple of new washers
from a finer grade of felt. This was obtained from the wife's
sewing stock at little (YOU cook the meal tonight) cost..
73
Stewart G3RXQ
On Sun, 21 Dec 2008 20:50:14 -0800 (PST), VK5ABQ wrote:
I was annoyed by the felt on felt
Following the thread concerning PLL errors on the higher frequency
bands, I decided to run a check on my K3.
I found that at a FP temp of over 38deg, I got a PLL2 error
message.
I then implemented the mod that Wayne recently posted in which a
180k resistor shunts R10 to give 56k. This cured the
That should take care of it
T.I.A.
73
Stewart G3RXQ
On Fri, 12 Dec 2008 12:47:29 -0800, Eric Swartz - WA6HHQ, Elecraft
wrote:
Hi Mike,
It is. This is something that doesn't show up all the time so we
were
not aware of it until it was noted here on the list recently.
We're adding an
Hi,
Since installing MCU 2.73. I have noticed that power on is
accompanied by a number of loud, rather unpleasant clicks/clunks
from the speaker.
73
Stewart G3RXQ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to
Nice firmware addition, works well.
Thanks Guys.
73
Stewart G3RXQ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
Lyle,
The high priority being given to the SUB IND is great news.
I suspect that a number of K3 users are already tuned in :-)
73
Stewart G3RXQ
Having the Sub Rx work on a different band than the Main is a
very high
priority work in progress. Stay tuned...
73,
Lyle KK7P
Using a pair of small Creative (non amplified) computer speakers,
and the audio quality from the K3 is excellent.
I must be very lucky, I can't hear any of the birdies listed.
My K3 has the 2nd RX, however I took no special care in the
routing of the signal cables.
73
Stewart G3RXQ
On Sun, 23
I noticed this as well, hope that it gets sorted soon..
73
Stewart G3RXQ
On Thu, 20 Nov 2008 17:19:27 -0800 (PST), Barry N1EU wrote:
N5WNG wrote:
The question is does the RX EQ get applied to both receivers?
No, with the current firmware, RX EQ is only applied to the main
rx. I'm
sure
Seconded...
Just what the 2nd RX needed.
73
Stewart G3RXQ
On Wed, 19 Nov 2008 09:37:53 +0100, Alexandr Kobranov wrote:
Excellent job, Wayne!
SUB/MAIN ballance and easy ANT switching is really big
improvement!
Many thanks,
Lexa, ok1dst
with still growing K3/10 :-)
wayne burdick
Documentation for the speaker mod says RFC47 is 100uH. However,
the circuit diagram is marked 10uH.
73
Stewart G3RXQ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr.
is 10mH. The marking on the new part
appears
to be 101 which I read as 100mH.
So it's just a recent change not reflected in the published
schematic.
Bob NW8L
On Sun, Nov 16, 2008 at 4:19 AM, Stewart Baker
[EMAIL PROTECTED] wrote:
Documentation for the speaker mod says RFC47 is 100uH.
However
Have you tried just running the mic into your K3 without the
external station controller ?
What is that controller ?
73
Stewart G3RXQ
On Sat, 1 Nov 2008 07:57:10 -0600, Dr. James C. Garland wrote:
Gang,
Im pulling my hair out over an RF feedback problem with my
K3/100, and wonder if
anybody
Make sure that the KRX3 is fully mated with the SUBIN board
connectors.
73
Stewart G3RXQ
On Wed, 29 Oct 2008 09:02:50 +0100, Mitch Wolfson DJØQN wrote:
Hi Lyle,
Thanks for the tip.I am using 2.46, and it didn't work until
you pointed
me in the right direction.
Since I had the AF
Not at present. I hope that this one is on the list.
73
Stewart G3RXQ
On Tue, 23 Sep 2008 14:49:14 +, Peter wrote:
Hi
I like to make a complete record of a qso.
With the line-out at the K3 connected to the sound card I can
record the
rx part.
Is it possible to echo the tx audio into
Yes, this fairly major feature of the K3 is missing.
No timescale for it's implementation been given.
73
Stewart G3RXQ
On Fri, 19 Sep 2008 20:15:13 +0900, a.yoshida wrote:
Just finished assembling my KRX3.
Everything seems to work as advertized except VFO IND
setting.
When I turn VFO A to
That's great news Eric, can't wait...
73
Stewart G3RXQ
On 19 Sep 2008 08:31:00 -0700, Eric Swartz - WA6HHQ, Elecraft
wrote:
We're actually working on the firmware for this now. :-)
Stay tuned!
73,
Eric WA6HHQ
_..._
-Original Message-
From: Stewart Baker [EMAIL PROTECTED]
Date
That's what I did.
73
Stewart G3RXQ
On Mon, 8 Sep 2008 08:00:42 -0400, Roy Morris wrote:
On page 34 of the Installation and Opeation manual it says to
remove the W4 jumber
soldered between two pads located between J64A and the KIO3
board. My K3 RF board is
Rev A. W4 is hard wired between two
If the rain doesn't stop soon we will be signing G3MDG/MM !
73
Stewart G3RXQ
Chesham District ARS
On Fri, 5 Sep 2008 04:49:35 -0700 (PDT), GW0ETF wrote:
Toby Deinhardt wrote:
Hi,
this weekend is our SSB Fieldday: Saturday 13UTC to 13UTC
Sunday.
Please listen for /p stations from region
site, hi
73 es GL
Glenn ON4WIX
- Original Message - From: Stewart Baker
[EMAIL PROTECTED]
To: GW0ETF [EMAIL PROTECTED]
elecraft@mailman.qth.net
Sent: Friday, September 05, 2008 2:51 PM
Subject: Re: [Elecraft] IARU Region 1 SSB Fieldday this
weekend
If the rain doesn't stop soon
I find virtually the same results here using 50uV RF from an
Elecraft signal source, and measuring using Wave Spectra.
An offset of 43 to 45dB, and below LIN OUT = 5 the harmonics drop
rapidly.
73
Stewart G3RXQ
On Tue, 02 Sep 2008 12:28:02 -0400, Jack Smith wrote:
Brendan:
You might wish to
I have had my K3 on receive most of the day, whilst doing other
things in the shack.
By chance I touched the top of the case and it felt quite hot,
given that the shack temperature is 26 deg. According to the LCD
readout both the FP and PA temps were at 34 deg.
It got me wondering, what are the
Thanks Gary (and others),
I think that since fitting the 2nd RX the unit gets quite a bit
warmer. The supply volts are 13.7 and the current on receive is
1.07A, so that's about 14W, not excessive.
If the unit is on receive and the fans are not running, the only
place for the heat to escape from
I don't know which beta release it was implemented in, but I
notice that when the VFO's are LINKED there is a Lock Icon against
VFO B.
I know that it is not possible to tune using VFO B when the VFO's
are linked, but I find the use of the Lock icon when in LINKED
mode confusing. It doesn't
My experience is that although it only takes a minute or so to
remove the KRX3, it takes quite a lot of time to re-install. Most
of that time being taken up in routing the coax cables.
73
Stewart G3RXQ
On Thu, 28 Aug 2008 07:27:40 -0700 (PDT), Barry N1EU wrote:
Terry Schieler wrote:
Will
On Thu, 28 Aug 2008 11:08:35 -0400, Barry N1EU wrote:
On Thu, Aug 28, 2008 at 10:58 AM, Stewart Baker
[EMAIL PROTECTED] wrote:
My experience is that although it only takes a minute or so to
remove the KRX3, it takes quite a lot of time to re-install.
Most
of that time being taken up
Any suggestions other than silicon sealant for keeping dust from
finding it's way onto the back of the LCD cover ?
I have to take the cover off about every couple of months to clean
it where dust has fallen down the gap with the front panel
metalwork.
The shack is not very dusty (despite what
That's a good idea. She can now put her very expensive Bernina
sewing machine which gives out sprogs all over 80 40 to good
use..
73
Stewart G3RXQ
On Thu, 28 Aug 2008 12:46:11 -0700 (PDT), Julian, G4ILO wrote:
doberman wrote:
How about the dust covers someone suggested a few or so posts
Yes, very good.
We've had ESSB Diversity implemented.
VFO IND next ?
73
Stewart G3RXQ
On Thu, 28 Aug 2008 10:42:15 -0700, wayne burdick wrote:
K3 beta-test firmware revision 2.31 is now available. This is an
extensive update; details appear below. Please send any problem
reports
to [EMAIL
I made a carbon copy of this ATU. It works pretty well, however at
impedance extremes it was a bit lossy.
73
Stewart G3RXQ
On Wed, 20 Aug 2008 09:12:01 -0700, Vic K2VCO wrote:
David Andrews wrote:
I'm using a h/b 1930's link (balanced) tuner. It's as efficient
as I can
get, and open wire
Since fitting the 2nd RX I have been exploring the audio settings
and find that:-
To get 1st 2nd RX audio thru the speaker I have SPKRS=1.
This is fine, however if I have SPKR+PH=YES, then I only get audio
from the LH headphone.
With SPKR+PH=NO, I get audio from both LH and RH headphones.
Is
. Works here.
73,
Ken K3IU
Stewart Baker wrote: Since fitting the 2nd RX I have been
exploring the audio
settings and find that:- To get 1st 2nd RX audio thru the
speaker I have SPKRS=1.
This is fine, however if I have SPKR+PH=YES, then I only get
audio from the LH
headphone. With SPKR+PH
The buzzing I noticed on my K3 is the top cover vibrating against
the top of the PA shield. There should be a greater clearance
between the two.
I have been waiting until there is a reason to disassemble my K3,
so I can take a file to the metalwork. That is what I would do if
I were building
Oh Yes !
73
Stewart G3RXQ
On Mon, 11 Aug 2008 10:56:36 +0100, David Ferrington, M0XDF wrote:
Strange, mine not only does not do that, but I can't make it do
that
even if I tap it - do you have the chassis stiffener in place
correctly?
___
Elecraft
below the pa unit. Fern
- Original Message -
From: Stewart Baker [EMAIL PROTECTED]
To: David Ferrington, M0XDF [EMAIL PROTECTED]
Cc: Fern Rivard [EMAIL PROTECTED] Elecraft List
elecraft@mailman.qth.net
Sent: Monday, August 11, 2008 4:14 AM
Subject: Re: [K3] annoying resonance
For convenience, I have generated a number of macros under the HRD
CAT command facility. I assigned them to buttons on the HRD front
panel. I have macros for TX EQ RX EQ for CW SSB.
For easy identification, part of the macro displays the name on
the K3 LCD bottom line.
E.g.
TX SSB1
Is that really so ?
If that's the case, then the design is poor..
73
Stewart G3RXQ
On Wed, 6 Aug 2008 09:32:55 +0200, Koppendorfer Klaus wrote:
did you use the line out ?? The Line Output
transformers of the K3, saturate at normal program levels
try Headphone out on Frontplate and you will
Looks more like an Air Freshener ::-)
73
Stewart G3RXQ
On Wed, 06 Aug 2008 16:17:33 +0100, Ian Maude wrote:
Bert Craig wrote:
How about Palstar's offering?
http://www.palstar.com/sp30.php
God that's ugly :)
73 Ian
___
Elecraft mailing list
Post
With the current recession (sorry credit crunch), I am thinking
about making my K3 available for hire for contests and
DXpeditions :-)
73
Stewart G3RXQ
On Thu, 31 Jul 2008 17:26:14 -0700 (PDT), W7TEA wrote:
Maybe you could have put your order on hold to keep your spot
in the queue
and then
It would be nice to have a LINE OUT setting something like =TX/RX
where both the received audio and the transmitted audio were
available at a preset (independent of volume control) level.
It would be very useful in contests to record both sides of a
contact CW or SSB.
73
Stewart G3RXQ
On Wed, 30
All fine in principle, but here in the UK, nobody is enforcing the
EMC legislation. Maybe Ireland is more fortunate.
73
Stewart G3RXQ
Member RSGB EMC Committee
On Sat, 26 Jul 2008 01:45:54 +0100, Brendan Minish wrote:
On Fri, 2008-07-25 at 13:29 -0700, Alan Bloom wrote:
However, I believe
Member RSGB EMC Committee
On Sat, 26 Jul 2008 09:43:27 +0100, Ian White GM3SEK wrote:
Stewart Baker wrote:
All fine in principle, but here in the UK, nobody is enforcing
the EMC
legislation.
It's true that nobody is enforcing it effectively against grey
imports.
On the other hand, those
I have had this on a number of occasions :-
*** DON'T PANIC ***
The Bad News is that something got screwed up on the recent
firmware download.
The Good News is that no harm was done, and your K3 is sitting
there ready to try again.
My advice would be to restart your computer, check your COM
My KRX3 came today. Installed in about 2.5 hours, with no
problems, however the coax cable routing was fun...
Very pleased with this addition to my K3.
My only comment so far is - why does switching the SUB RX
ON/OFF/ON cancel SPLIT ?
I would prefer that the operator has full control over the
Wow, that was quick !
I only went downstairs to make a cup of tea
I will look out for MCU 2.17.
73
Stewart G3RXQ
On Tue, 22 Jul 2008 09:43:13 -0700, Ed Muns wrote:
My only comment so far is - why does switching the SUB RX
ON/OFF/ON cancel SPLIT ?
This is fixed in MCU 2.17, so QRX for
To prevent inadvertent QSY's, I would like to have the RIT coarse
tune (CONFIG:VFO OFS) be locked when the LOCK button is pressed.
73
Stewart G3RXQ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
I agree Julian,
Let's use the Little Gray Cells between our ears.
If not, there's always EchoLink, Skype etc.
73
Stewart G3RXQ
On Mon, 21 Jul 2008 00:49:10 -0700 (PDT), Julian, G4ILO wrote:
Brett Howard wrote:
Personally I'd rather have the ability to do CW in SSB anywhere
as it
turns out
I brought a 6m preamp kit from Down East Microwave.
It cost only slightly more than if I had sourced the components in
the UK. The end result means that now I can hear the K3 noise
level increase when I add an antenna.
73
Stewart G3RXQ
On Fri, 18 Jul 2008 10:33:21 -0700, Jim Brown wrote:
On Fri,
I'm ready for another holiday in the US next year, before the UK
economy gets much weaker :-(
73
Stewart G3RXQ
On Sat, 19 Jul 2008 08:45:57 -0700, Jim Brown wrote:
On Sat, 19 Jul 2008 09:46:56 +0100, Stewart Baker wrote:
I brought a 6m preamp kit from Down East Microwave.
They are well
.
73
Dave KD1NA
From: Stewart Baker [EMAIL PROTECTED]
Subject: Re: [Elecraft] Re: KAT3 ATU and SPE Expert 1K-FA
Amplifier
To: Dave G4AON [EMAIL PROTECTED],
elecraft@mailman.qth.net
Message-ID: [EMAIL PROTECTED]
Content-Type: text/plain; charset=ISO-8859-1
I made some measurements
Shouldn't mess with things !!
In preparation for my KRX3 which is on the way to me, I thought
that I would be clever and load the latest Beta firmware.
The MCU LD crashed, and now I cannot get my K3 to INIT using the
POWER switch and NORM controls. I sits there with MCU LD message
on the
I made some measurements of the isolation between ANT 1 ANT 2 on
my K3.
There is little difference between ATU BYPASS. Unable to do
50MHz.
1.9MHz 58.1dB
3.7MHz 51.9dB
5.1MHz 49.2dB
7.0MHz 47.1dB
10MHz 44.7dB
14MHz 42.5dB
18MHz 40.8dB
21MHz 39.2dB
Same here. I have two of these supplies, and have yet to hear a
peep of RF noise from them.
73
Stewart G3RXQ
On Mon, 7 Jul 2008 21:50:08 -0400, Bruce McLaughlin wrote:
I am having very good performance from the SEC 1223 which is the
same supply
I use with the K2/100. If it does generate any
I believe that all new SEC1223's have the mods fitted.
73
Stewart G3RXQ
On Tue, 08 Jul 2008 14:40:27 +0200, Jan Erik Holm wrote:
Mike Penkas wrote:
I have 2 SEC1223's and no hash. I also have an Astron RS35 and
RS50
linear supplies. Sometimes the magnetic hum from them drives
me crazy.
The
Yup, it's pretty good..
73
Stewart G3RXQ
On Mon, 7 Jul 2008 09:59:51 -0600, Bill W5WVO wrote:
To those of you SSB ops who won't use VOX because every
implementation of it you've
ever used basically sucked -- Try the K3! I just set it up using
my Heil Pro-Set for
the first time, and it works
Is that do do or can do ?
73
Stewart G3RXQ
On Mon, 07 Jul 2008 10:25:32 -0700, Eric Swartz - WA6HHQ, Elecraft
wrote:
DSP based VOX is very cool. :-) We can do some interesting
things to
avoid dropped first syllables.
Eric WA6HHQ
Stewart Baker wrote:
Yup, it's pretty good..
73
Stewart
.
73, Eric
Stewart Baker wrote:
Is that do do or can do ?
73
Stewart G3RXQ
On Mon, 07 Jul 2008 10:25:32 -0700, Eric Swartz - WA6HHQ,
Elecraft
wrote:
DSP based VOX is very cool. :-) We can do some interesting
things to avoid
dropped first syllables
Thanks Bill,
That was a question I was going to ask :-)
73
Stewart G3RXQ
On Sun, 06 Jul 2008 09:51:23 -0500, ny9h wrote:
now that I received my katiegram for the second receiverI
have
read the instructions. Looks like I need to make a decision
whether
to hook the 2nd rcvr aux in to the
Pleased it wasn't me losing it.
Whilst in the memory area, I would like to have the ATU/Bypass
status stored Band by Band.
I have some bands where I use the K3 barefoot, and others where it
goes either to an amplifier or to an external balanced ATU.
Sometimes when changing bands I forget to
On 6m if I select the mode as CW, then save and recall from a
memory I get CW REV. Is this correct ?
73
Stewart G3RXQ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr.
My advisory came today - shipping in 2 weeks.
Should be up and running (not sure about the op! ), in plenty of
time for CQWW.
73
Stewart G3RXQ
K3 #307
On Wed, 2 Jul 2008 21:34:05 -0500, Nelson Moyer wrote:
Thanks, and please keep the KRX3 advisories coming so I can
predict when my
September
I have just finished putting together, and testing a 6m preamp kit
from Down East Microwave. As I use the RX Ant input on the lower
bands, and not wanting to put in a relay, I have made up a
Diplexer to separate out the 2 signal paths.
Although the arrangement is a bit of a lash up it has proved
As far as I can see it is not possible at present. It is fairly
high on my should be quick to implement wish list :-)
73
Stewart G3RXQ
On Thu, 3 Jul 2008 04:22:59 -0700 (PDT), K3KO wrote:
Anybody figure out if it is possible to display a delta F value
instead of
the actual VFO B frequency when
see the delta F in place of the VFO B. The
only
downside is that you have to use the small knob to set y our
delta f.
On Thu, 2008-07-03 at 12:41 +0100, Stewart Baker wrote:
As far as I can see it is not possible at present. It is fairly
high on my should be quick to implement wish list
I would hang on to your XV-50 until you have checked that you find
your K3 sensitive enough on 6m. I made the mistake of selling mine
off before my K3 arrived, and I now regret it.
73
Stewart G3RXQ
On Mon, 23 Jun 2008 13:19:51 -0500, Terry Schieler wrote:
Fellow Elecraftorians:
Some weeks
Overall I am very pleased with the review that Peter produced.
Having chided him somewhat over the lack of a K2 review, I and
others pushed him quite hard towards producing one for the K3.
Given that the K3 is quite a different beast to the Far East Black
Boxes he normally reviews, the end result
1 - 100 of 385 matches
Mail list logo