Re: [Elecraft] K3/0 and RTTY

I should also mention we are using Fiber to the home for Inet here and 10MB DSL link at the remote Typical ping times are 50MS range and Latency range is usually 10-20 range and Jitter 0-4 range usually 0 as it was a moment ago when tested. Not sure why RTTY decode is a problem using the s

Re: [Elecraft] K3/0 and RTTY

Got the CONFIG: SYNC DT off finally...Thanks so much. RX Signal levels on RTTY are S9+..still gibberish decode over the Remote system? -Original Message- From: Wayne Burdick Sent: Sunday, February 08, 2015 2:43 PM To: Larry - K1UO Cc: Elecraft Reflector Subject: Re: [Elecraft] K3

Re: [Elecraft] K3/0 and RTTY

Both RTTY and CW decode should work remotely. Use a narrow filter passband tune the signal in carefully using the CWT meter scale (pgs. 33 and 34 of the owner's manual). Decode accuracy is affected by noise, fading, and interference, but should work as long as the signal is correctly tuned in an

[Elecraft] K3/0 and RTTY

I have a K3/0 and remote K3 setup using the RemoteRig boxes from Elecraft. SSB/CW is fine. When I switch the K3/0 to DATA mode and set up the onboard text decode and FSK to 45Bps . I get nothing but gibberish.. There is NO decoding possible for RTTY and the CW-RTTY does not key the remote un

[Elecraft] K3/0 Mini Firmware Update???

As Elecraft knows there is a bug in the firmware for the K3/0 Mini that causes it to time out approximately three minutes into a conversation unless you unkey before the time out. When can we expect you to fix your bug? I paid a lot of money for my complete K-Line and would like to be able to use

[Elecraft] K3/0-mini or K3/0

Hello, Have somebody of you an K3/0 mini or K3/0 for sale ? (What standard is the 12 vdc conn. on K3/0 mini ) ? 73'Viggo M . LA9NEA __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qt

[Elecraft] K3/0 Mini Configuration Help Please

I recently purchased the K3/0 Mini and I still can't get it configured correctly. I have it about 90% working. *Is there a DEFINITIVE guide that shows how to configure the K3/0 with the RigTalk to work with a complete K-Line (K3, P3, KPA 500, KTA 500) and CAT logging to a computer? *I have the K3/0

Re: [Elecraft] K3/0 all in one box? + P3/0

tially the same > situation as someone with CC&R. > > From: > To: > Subject: Re: [Elecraft] K3/0 all in one box? + P3/0 > Message-ID: <004801d02ffc$bda1dc70$38e59550$@net> > Content-Type: text/plain; charset="us-ascii" > > Sorry for my conf

Re: [Elecraft] K3/0 all in one box? + P3/0

ering From: Walter Underwood To: Elecraft Reflector Sent: Wednesday, January 14, 2015 5:00 PM Subject: Re: [Elecraft] K3/0 all in one box? + P3/0 Two channels of 16-bit 192kHz audio compressed with FLAC should use around 500kbits/s. That is a chunk of bandwidth, but it is fairly reasonable

Re: [Elecraft] K3/0 all in one box? + P3/0

torage lot someday with me an old > codger living in assisted-living with a computer for control; > essentially the same situation as someone with CC&R. > > From: > To: > Subject: Re: [Elecraft] K3/0 all in one box? + P3/0 > Message-ID: <004801d02ffc$bda1dc70$38e5955

Re: [Elecraft] K3/0 all in one box? + P3/0

e nice to >> have the control station use a P3 with the extra data lines intergraded into >> the 1258, or K3/0 mini mark II :-). >> >> >> 73 Jeff kb2m >> >> -Original Message- >> From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf

Re: [Elecraft] K3/0 all in one box? + P3/0

@mailman.qth.net] On Behalf Of Fred > Jensen > Sent: Tuesday, January 13, 2015 19:59 PM > To: elecraft@mailman.qth.net > Subject: Re: [Elecraft] K3/0 all in one box? + P3/0 > > Hmmm ... K3 1st IF is ~8 MHz. Could pose some problems for generally > available "overIP&

Re: [Elecraft] K3/0 all in one box? + P3/0

meday with me an old codger living in assisted-living with a computer for control; essentially the same situation as someone with CC&R. From: To: Subject: Re: [Elecraft] K3/0 all in one box? + P3/0 Message-ID: <004801d02ffc$bda1dc70$38e59550$@net> Content-Type: text/plain; ch

Re: [Elecraft] K3/0 mini

It's not completely clear from the K3/0-mini documentation (which is rather high-level), but it appears that it only has a TTL interface (for connection to the RemoteRig box), and not RS232, so you wouldn't be able to directly connect it to a K3 using a "null modem" cable, as you could with the ori

Re: [Elecraft] K3/0 mini

Does that mean all the wires and hardware that would be used for a real remote operation are needed just to get the faceplate on the desk for ease of use? Please explain - it has been very difficult to get this question answered. Thanks, Bill W2BLC K-Line ___

Re: [Elecraft] K3/0 mini

Yes, but it's not as portable as you'd think. I have the whole remoterig set up and I'm remoting a whole foot. It actually frees up a lot of space on my desk. On Wed, 14 Jan 2015, W2BLC wrote: Does anyone use the K3/0 mini as a movable faceplate on their main desk? If so, how is it connected to

Re: [Elecraft] K3/0 all in one box? + P3/0

-boun...@mailman.qth.net] On Behalf Of Fred Jensen Sent: Tuesday, January 13, 2015 19:59 PM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3/0 all in one box? + P3/0 Hmmm ... K3 1st IF is ~8 MHz. Could pose some problems for generally available "overIP" for many people. I/Q sounds li

[Elecraft] K3/0 mini

Does anyone use the K3/0 mini as a movable faceplate on their main desk? If so, how is it connected to the K3? Bill W2BLC K-Line __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.n

Re: [Elecraft] K3/0 all in one box?

(First post on this reflector!) Well, an ethernet link can go up to 10Gbit on modern ethernet links, so sending an 8MHz signal with a decent sampling rate and resolution is definitely possible, but only on a local network... As an extreme, the Arecibo radiotelescope uses RF over fiber all over

Re: [Elecraft] K3/0 all in one box?

Jeff, I am not certain how you could send the 8 MHz IF signal over an Ethernet link. It may be possible to use some derivative of that signal - such as hardware using the output of the SVGA option to send the digitized result (SVGA signaling) of the IF passband to the control location, but to

Re: [Elecraft] K3/0 all in one box? + P3/0

Hmmm ... K3 1st IF is ~8 MHz. Could pose some problems for generally available "overIP" for many people. I/Q sounds like a better way to go with a PX3? I guess that would require an outboard quadrature demod at the "real" K3. While I don't do remote stuff right now, we're eventually going t

Re: [Elecraft] K3/0 all in one box? + P3/0

gt; To: 'Elecraft Reflector' > Sent: Tuesday, January 13, 2015 5:27 PM > Subject: Re: [Elecraft] K3/0 all in one box? > > I already own a K3/0 mini, RRC-1258, power supply, etc. I would sell all of > this and buy a K3/0 mini, and remote box as you describe, 'IF&#x

Re: [Elecraft] K3/0 all in one box? + P3/0

current chips for multimedia and possible some of the open source CODEXsit may be a workable item, though I would expect it to me a bit off a pricey option From: "k...@arrl.net" To: 'Elecraft Reflector' Sent: Tuesday, January 13, 2015 5:27 PM Subject: Re: [E

Re: [Elecraft] K3/0 all in one box?

have to dictate... What do you think Wayne :-) 73 Jeff kb2m -Original Message- From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Harry Yingst via Elecraft Sent: Tuesday, January 13, 2015 15:44 PM To: Elecraft Reflector Subject: [Elecraft] K3/0 all in one box? About a

Re: [Elecraft] K3/0 all in one box?

Reflector Sent: Tuesday, January 13, 2015 4:29 PM Subject: Re: [Elecraft] K3/0 all in one box? Harry: Interesting idea.  Reducing "clutter" and simplifying hookup to only requiring power and internet access does have appeal.  Not having to unplug and replug between K3/O-Mini and Remo

Re: [Elecraft] K3/0 all in one box?

Harry: Interesting idea. Reducing "clutter" and simplifying hookup to only requiring power and internet access does have appeal. Not having to unplug and replug between K3/O-Mini and RemoteRig will reduce errors. For example, I have managed to connect the wrong item to the wrong port because

[Elecraft] K3/0 all in one box?

About a year ago I had strongly considered getting the full size K3/0and putting the RemoteRig inside so it would be self contained. Now with the K3/0 Mini it got me thinking that a nice accessory would be a box thatwould hold the Remote Rig, a small power supply and possibly a wireless adapter.

Re: [Elecraft] K3/0 mini remote, panadapter display at control site

Hi If you have a pc with a spare pcie slot at the remote site you can use the avermedia hd game broadcaster with the p3 svga. It comes with streaming software. Tom Tom On Jan 11, 2015 8:58 AM, Don Wilhelm wrote: > > Jeff, > > I have heard of some who are using a webcam at the remote site to

Re: [Elecraft] K3/0 mini remote, panadapter display at control site

Jeff, I have heard of some who are using a webcam at the remote site to view the P3. I am not certain how you would pass any RF signal (and the IF output is RF at 8 MHz) from the remote to the control site without using a direct coax run. I guess it *might* be possible to transmit the inte

[Elecraft] K3/0 mini remote, panadapter display at control site

I know several people are working on getting the IF from the remote K3 to the K3/0 control site. Has anyone got this working, and would like to share their method with the group? Is it possible for Elecraft to add forwarding of the IF with a mod to the existing hardware? I sorely miss my panadapter

[Elecraft] K3/0 FOR SALE

K3/0 (not mini) for sale. Includes RRK0CBL cable set. Excellent condition - nonsmoking environment, $600.00. Please contact me off the reflector: k9nu at mchsi.com. 73, Paul K9NU __ Elecraft mailing list Home: http://mailman.qth.ne

[Elecraft] K3/0 or Mini WANTED:

If you replaced your K3/0 with a K3/0 mini, or are not using your K3/0, I may be interested in purchasing it. Actually interested in the K3 mini if you have one and are not using it. I am looking for the K3 control RRC and cables as well. Regards

Re: [Elecraft] K3/0 mini remoting problem

Great!Happy to hear it was such an easy fix! 73 de Jim - KE8G Sent from my iPad > On Oct 3, 2014, at 11:25 PM, "bwru...@gmail.com" wrote: > > Wow! Just unplugged and replugged all the RS232 lines, and it works! > > Thanks for the help--- I am very pleased with the result. > > 73 de Bria

Re: [Elecraft] K3/0 mini remoting problem

Wow! Just unplugged and replugged all the RS232 lines, and it works! Thanks for the help--- I am very pleased with the result. 73 de Brian W3BW Brian F. Wruble, C.F.A. >From my iPad > On Oct 3, 2014, at 10:43 PM, KE8G wrote: > > Hi Brian, > Try removing the cable from the K3 RS232 and mak

[Elecraft] K3/0 mini remoting problem

Hi guys: Last year, I had wonderful success controlling my "big station" (K3, KPA500,KAT500) on Maryland's Eastern Shore from our winter home in Key West. When I took the setup down last May, I carefully documented every step required to set things back up. Well, I have just gone through that

[Elecraft] K3/0

Hi, I understand that the K3/0 will provide 100% complete emulation of a K3 remotely. Therefore, all commands that can be used at a K3 directly, will be usable at the K3/0. I would like to communicate off list, with owners of the K3/0, who are willing to provide me with some information of it’s

[Elecraft] K3/0 Mini FSK RTTY Setup Info

It took me some time to get FSK RTTY working properly with the K3/0 Mini and the Remote Rig interface. Getting it to work smoothly with Writelog was especially challenging so I decided to write up my settings and connections and pass that info along to others who might be having as much difficulty

Re: [Elecraft] K3/0 mini observations

To be honest I already waited for the first such comment to appear. Sorry Slava, this is not against you personally. I simply cannot hear all the praise anymore for cases which were wrong right from the beginning (and from people not even owning the product in question). Amazingly I already g

Re: [Elecraft] K3/0 mini observations

Now i ask you: where else would you get an even remotely similar level of service and commitment to customer? __ Slava (Sal) B, W2RMS w2...@arrl.net On Jun 16, 2014, at 10:27 PM, Wayne Burdick wrote: > Hi Oliver, > >> The mini is used in tilted postion like the KX3. So I would

Re: [Elecraft] K3/0 mini observations

Hi Oliver, > The mini is used in tilted postion like the KX3. So I would have expected the > same display like in the KX3 to be used… We switched to the KX3 display very early in production. Contact customer support for a replacement (or we can do it for you, no charge). > The manual gives a

Re: [Elecraft] K3/0 mini observations

On 6/16/2014 3:51 PM, Oliver Dröse wrote: ... Display The mini is used in tilted postion like the KX3. So I would have expected the same display like in the KX3 to be used, i.e. with a "6 o'clock" viewing angle. Sorrily it's not, it has the original K3 display ("12 o'clock") so you cannot see

[Elecraft] K3/0 mini observations

Hi, having used the K3/0 mini for a few weeks now here are some observations, maybe they can be taken into account to make the product even better. Display The mini is used in tilted postion like the KX3. So I would have expected the same display like in the KX3 to be used, i.e. with a "6

Re: [Elecraft] K3/0 question: serial from the K3/0 to a logging program?

On Sun, 15 Jun 2014, Hisashi T Fujinaka wrote: Does the K3/0 do serial comminications to a logging program? I can't seem to get it working, so my current guess is no. And once again I found the answer (I think) right after sending an email. It's in the RRC manual online. -- Hisashi T Fujinaka

[Elecraft] K3/0 question: serial from the K3/0 to a logging program?

Does the K3/0 do serial comminications to a logging program? I can't seem to get it working, so my current guess is no. -- Hisashi T Fujinaka - ht...@twofifty.com BSEE(6/86) + BSChem(3/95) + BAEnglish(8/95) + MSCS(8/03) + $2.50 = latte _

Re: [Elecraft] K3/0-Mini Remote makes me wonder....

If I change over to a K3/0 Mini for the remote control point, how about a kit with all the parts required to upgrade my now unused K3/0 to a fully functional K3? 73 John N5CQ __ Elecraft mailing list Home: http://mailman.qth.net/mailma

Re: [Elecraft] K3/0 Mini F posted on elecraft website

Wow tnx. Tha's a goood news woohoo Vy73 de ve3gno Daniel Sent from Yahoo Mail on Android __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailma

Re: [Elecraft] K3/0 Mini F posted on elecraft website

There will be an announcement shortly. Wayne N6KR On Mar 19, 2014, at 11:35 AM, VE3GNO Daniel wrote: > Hi All > > I've seen the K3/0-MINI-F posted on Elecraft website $699.95. Is just a > pre-announcement? Any manuals pls and a guestimate of delivery. ___

[Elecraft] K3/0 Mini F posted on elecraft website

Hi All I've seen the K3/0-MINI-F  posted on Elecraft website  $699.95. Is just a pre-announcement? Any manuals pls and a guestimate of delivery    Tnx vy 73 de VE3GNO Daniel __ Elecraft mailing list Home: http://mailman.qth.net/mailman/

Re: [Elecraft] K3/0 Mini Soon?

Pictures? 73, Jim KG0KP -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Paul DeFelice Sent: Saturday, February 22, 2014 7:19 AM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3/0 Mini Soon? Must be close because it

Re: [Elecraft] K3/0 Mini Soon?

Must be close because it was on display at the Orlando Hamcation a couple of weeks ago. 73, Paul K9NU __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto

[Elecraft] K3/0 Mini Soon?

I'm hoping the sheet metal issues have been cleared up regarding the K3/0 mini... Any news on ship date? 73, -- Gerry Hull, W1VE | Nelson, NH USA | +1-617-CW-SPARK AKA: VE1RM | VY2CDX | VO1CDX | 6Y6C | 8P9RM

Re: [Elecraft] K3/0 Remote setup and Brainboxes

Thanks for your information, John. This morning I went on the Brainboxes web site and took advantage of their support page. All is set up and fine now. 73, Paul K9NU __ Elecraft mailing list Home: http://mailman.qth.net/mailman/list

Re: [Elecraft] K3/0 Remote setup and Brainboxes

port forwarding info. 73, John NI0K -- Original Message -- From: "Paul A DeFelice" To: elecraft@mailman.qth.net Sent: 1/5/2014 9:47:46 AM Subject: [Elecraft] K3/0 Remote setup and Brainboxes As part of my remote setup, I purchased a Brainboxes ES-257 2 Port RS232 ethernet

[Elecraft] K3/0 Remote setup and Brainboxes

As part of my remote setup, I purchased a Brainboxes ES-257 2 Port RS232 ethernet to serial adapter to control a couple of serial port accessories. I can control the ES-257 and the attached equipment using their Boost.LAN Manager software over my LAN but cannot get the device configured to accept

[Elecraft] K3/0 Line in/out for AFSK

I am trying to operate AFSK modes remotely using K3/0 to K3 and RemoteRig. I have stereo cables running from line in/out on the back of the K3/0 to my PC sound card. I am getting no audio from the K3/0 to the PC. If I connect to the front panel headphone jack, I do get audio. Is there a menu

[Elecraft] K3/0 to K3 Sound card digital

Guys, what is the best way to cable the K3/0 plus Remote Rig to a PC for sound card digital ops? Tnx. HNY, Brian W3BW -- Brian F. Wruble, CFA 1107 Key Plaza, PMB 447 Key West, FL 33040-4077 PO Box 57, 7400 Augustine Herman Highway, Georgetown, MD 21930-0057 eFax 305.768.0278 __

[Elecraft] K3/0 to K3 with contest programs

Hi all: I have a very nicely functioning remote setup. I control the complete K-Line in Maryland from a K3/0 in Key West. However, I have tried and tried, and I cannot get CW keying to work with N1MM or Writelog. I do have CW working with my regular (non-contest) logger, CommCAT. It uses the

Re: [Elecraft] K3/0 to K3 RemoteRig issue: NEVER MIND

No, I can ping the U-Verse router. I cannot ping my distant router, where my remotely controlled station is, from within the U-Verse network. I can ping it from outside the U-Verse network. Very weird. -- 70 is the new 40. Brian F. Wruble, C.F.A. 1107 Key Plaza, PMB 447 Key West, FL 33040 S

Re: [Elecraft] K3/0 to K3 RemoteRig issue: NEVER MIND

Your U-Verse router settings are set to not respond to ping request, you could change the settings in the router to respond to ping request. 73, Michael - N8NOC K1-4 #3046 K3/10 #6596 KX3#1573 On Dec 19, 2013, at 9:45 AM, bwru...@gmail.com wrote: It works. No idea why, but this morning e

Re: [Elecraft] K3/0 mini - when???

Don't know; didn't ask, but at Dayton in May they said same price as current K3/0 Buzz W3EMD Message: 1 Date: Sat, 14 Dec 2013 12:00:53 -0500 From: Bill W2BLC To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3/0 mini - when Message-ID: <52ac8ec5.7010...

Re: [Elecraft] K3/0 mini - when????

Just have to ask: How much is this going to cost? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http:/

Re: [Elecraft] K3/0 mini - when????

n the order list! Yes, I know at Dayton they promised early Fall. Buzz W3EMD Message: 10 Date: Thu, 12 Dec 2013 23:15:22 +0100 From: Oliver Dr?se To: elecraft@mailman.qth.net Subject: [Elecraft] K3/0 mini - when? Message-ID: <52aa357a.5050...@necg.de> Content-Type: text/pla

Re: [Elecraft] K3/0 mini - when????

W3EMD Message: 10 Date: Thu, 12 Dec 2013 23:15:22 +0100 From: Oliver Dr?se To: elecraft@mailman.qth.net Subject: [Elecraft] K3/0 mini - when? Message-ID: <52aa357a.5050...@necg.de> Content-Type: text/plain; charset=ISO-8859-15; format=flowed Hi guys, any news

[Elecraft] K3/0 to K3/100 with RemoteRig: CW how? Digital how?

Hello all, I have got my K3/0 here in Key West beautifully controlling my K3/100 + KPA500 + KAT500 located at my big station in MD. I cannot figure out how to get CW keying using N1MM or Writelog. Can someone guide me through the hookup? I am able to read frequencies from the K3/0 using var

Re: [Elecraft] K3/0 mini - when?

To be fair, Autumn is officially from the Equinox to the winter Solstice, which is on the 21st - so Autumn is not over yet :-) 73 de David, M0XDF (K3 #174, P3 #108) You must have been warned against letting the golden hours slip by. Yes, but some of them are golden only because we let them slip b

[Elecraft] K3/0 mini - when?

Hi guys, any news re the K3/0 mini? "Autumn" 's gone a while now. ;-) Thanks & 73, Olli - DH8BQA __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecra

[Elecraft] K3/0 to K3 Problem: working again

If you have ideas, please email direct. I forgot that I was in "digest mode" for this list. After multiple recycling of the power to the radio end router, I am back in business. I am going to just leave it on until the contest ends. 73 de Brian W3BW *Brian F. Wruble, C.F.A. *70 is the new 40

[Elecraft] K3/0 to K3 Remote stopped working

Hi all. I could use some advice. I have spent the last several months building the complete K-Line for my MD summer QTH. I am now preparing to operate via RemoteRig from a K3/0 located remotely. I was hoping for a test run in Sweepstakes this weekend. Everything was working fine, and starti

Re: [Elecraft] K3/0 to K3/100 twin issue at K6LRG - mode switches usb to cw

you are up and running! Chris N6WM From: elecraft-boun...@mailman.qth.net [elecraft-boun...@mailman.qth.net] On Behalf Of Walt W0CP [w...@comcast.net] Sent: Sunday, November 10, 2013 7:49 AM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3/0 to K3

Re: [Elecraft] K3/0 local site software

Although I have also used Eltima's products in the past, they require a PC to be running at the remote location. Therefore I highly recommend another method for remote stations: serial device servers. These small devices plug into the network and carry the serial ports over the internet with n

[Elecraft] K3/0 local site software

Prior to purchasing a K3/0 with the remote rig boxes, I had been using HRD. My accessory equipment (Alpha 87A, 2 rotor controllers, power meter, etc.) were handled by using the HRD Serial Port Client in conjunction with the 3rd party N8VB vCOM Virtual Serial Port Driver software. Unfortunately, the

Re: [Elecraft] K3/0 to K3/100 twin issue at K6LRG - mode switches usb to cw

After more testing, I see that, as stated previously, this is a display problem. When in ssb mode and pressing PTT I am modulating the k3 even though the k3/0 diplays cw mode. -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-0-to-K3-100-twin-issue-at-K6LRG-tp7567299p758

Re: [Elecraft] K3/0 to K3/100 twin issue at K6LRG - mode switches usb to cw

Thanks for the info, Chris. In this case, I think it is actually switching to cw mode since it won't modulate with a mike that works just fine on the k3. I'm new to this, so I'll do some more digging and see what I can find out. 73, Walt W0CP -- View this message in context: http://elecraft.365

Re: [Elecraft] K3/0 to K3/100 twin issue at K6LRG - mode switches usb to cw

boun...@mailman.qth.net [elecraft-boun...@mailman.qth.net] On Behalf Of Walt W0CP [w...@comcast.net] Sent: Wednesday, November 06, 2013 8:36 AM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3/0 to K3/100 twin issue at K6LRG - mode switches usb to cw I am having this problem right now. Front panel

Re: [Elecraft] K3/0 to K3/100 twin issue at K6LRG - mode switches usb to cw

CW+SSB is not enabled -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-0-to-K3-100-twin-issue-at-K6LRG-tp7567299p7580492.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list H

Re: [Elecraft] K3/0 to K3/100 twin issue at K6LRG - mode switches usb to cw

I am having this problem right now. Front panel PTT activation switches the mode to cw from USB on the local radio only. Front panel XMIT button does not do this. I don't have any computer (logging program) attached on either end. -- View this message in context: http://elecraft.365791.n2.nabb

[Elecraft] K3/0 Mini when?

Any idea when the mini will become available? 73 de Brian W3BW -- 70 is the new 40. Brian F. Wruble, C.F.A. 1107 Key Plaza, PMB 447 Key West, FL 33040 Summers: P.O.Box 57, 7400 Augustine Herman Highway, Georgetown, MD 21930 eFax 305.768.0278 Skype bwruble

[Elecraft] K3/0 tx audio problem

Hi Doug, Just wanted to let you know that I'm up and running. I called Elecraft on Monday and Brandon helped me. What a pleasure to work with the Elecraft staff. Main problem was that I need to remove JMP1 (default is bias on) in the control RRC-1258. I did not realize that some mics that don't nee

Re: [Elecraft] K3/0 tx audio problem

Paul: Assuming that you are using the Elecraft cables - the mic audio and PTT from the front panel Mic connector of the K3/0 is hard wired to the Mic mono and PTT In on the rear panel of the K3/0. The Elecraft cable then takes those signals to the AUX/MIC RJ-45 connector on the front panel of

[Elecraft] K3/0 tx audio problem

Just received my K3/0 and in the process of setting it up. RX, dual RX and CW are working great. I can't get any audio on SSB. I have the remote (K3/100) MIC SEL set to rP.L and the local K3/0 MIC SET set to fP.L . The mic plugged into the front connector of the K3/0. PTT is working but no ALC defe

[Elecraft] K3/0

K3/0 forsale with leads to connect to rig remote box . Contact g3...@btinternet.com Sent from Samsung Mobile __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: ma

[Elecraft] K3/0 forsale

K3/0 forsale with leads forsale $600 dollars . Contact : g3...@btinternet.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net Th

Re: [Elecraft] K3/0 to K3

It works!!! FANTASTIC!!! Thanks so much iain. I had to make the baud rate change to 38400. It was set to 9600. 73, Steve K6SAB On Aug 24, 2013, at 11:00 AM, iain macdonnell - N6ML wrote: > On Sat, Aug 24, 2013 at 9:58 AM, Steven Bertsch wrote: >> My friend uses the K3/0 to connect to my K3,

Re: [Elecraft] K3/0 to K3

On Sat, Aug 24, 2013 at 9:58 AM, Steven Bertsch wrote: > My friend uses the K3/0 to connect to my K3, and that works fine. > > But when I use my K3, I use Ham Radio Deluxe which would normally connect to > the 9 pin RS232 on the back of my K3, but since I have one of the remote > boxes connected

[Elecraft] K3/0 to K3

My friend uses the K3/0 to connect to my K3, and that works fine. But when I use my K3, I use Ham Radio Deluxe which would normally connect to the 9 pin RS232 on the back of my K3, but since I have one of the remote boxes connected to my K3 9 pin RS232, I would use the com1 on the front of the r

Re: [Elecraft] K3/0 to K3 issues mostly solved

I am not an authority on Remote Rig, but it would seem to be that JMP1 controls the microphone bias. The Heil Proset-K2/K3 sold by Elecraft is essentially the same as the Proset-iC in that it needs bias to operate. There are so many versions of Heil microphones that one needs to be specific abou

[Elecraft] K3/0 to K3 issues mostly solved

Brandon gave me about an hour on the phone, and we got all the settings just right. I can now operate remotely using RemoteRig and the K3/0 to my K3/100. It works --- with a couple of quirks. Quirk 1--- if you use the Heil ProSet Elite iC (made specially for Icom,) the jumper JMP1 in the con

[Elecraft] K3/0 to K3/100 RemoteRig Can't Get Icom mikes to Work

I have tried everything. Yes, I have the jumper out in the control box of the RemoteRig. Has anybody successfully gotten a Heil mike to work? My MH2 works FB with the JMP1 jumper in. I have full function and have had a successful remote QSO, linked over the internet. I have absolutely no audio

[Elecraft] K3/0 to K3 Working

I have the remote setup working on the desktop. It is pretty neat the way the K3 is slaved to the K3/0. Every button, every knob --- they move in lockstep. Audio quality is definitely degraded even though both RemoteRig is plugged into the same router. I have an immediate question --- is there

Re: [Elecraft] K3/0 Mini

I will be placing a first hour order on website for one. Last I heard was August of this year. Keith AK6ZZ Sent from my iPhone please excuse typos On Jul 23, 2013, at 7:10 AM, "Brian F. Wruble" wrote: > Anyone know when this will be available? > > Tnx de Brian W3BW > > > *Brian F. Wruble,

[Elecraft] K3/0 Mini

Anyone know when this will be available? Tnx de Brian W3BW *Brian F. Wruble, C.F.A. *70 is the new 40.* * Mail: 1107 Key Plaza, PMB 447 Key West, FL 33040-4077 Summers: P.O.Box 57, 7400 Augustine Herman Highway, Georgetown, MD 21930 eFax 305.768.0278 ___

[Elecraft] K3/0 Mini at W4DXCC.COM

Hi Everyone, Last year we had the original K3/0 operational at the W4DXCC - DX and Contest Convention last year in September.  This year W4DXCC is September 27th and 28th in Pigeon Forge TN and I am wondering if the K3/0 Mini will be shipping by then, anyone know? I would like to have it runni

Re: [Elecraft] K3/0 Question

an.qth.net] On Behalf Of Eric Swartz WA6HHQ - Elecraft Sent: Sunday, May 19, 2013 4:32 PM To: iain macdonnell - N6ML Cc: Elecraft Reflector Subject: Re: [Elecraft] K3/0 Question The K3/0 via the RemoteRig boxes absolutely -can- power up and down the remote K3. It uses a pin on the K3 AuxPort that

Re: [Elecraft] K3/0 Question

e- >> From: elecraft-boun...@mailman.qth.net >> [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Eric Swartz WA6HHQ >> - >> Elecraft >> Sent: Sunday, May 19, 2013 4:32 PM >> To: iain macdonnell - N6ML >> Cc: Elecraft Reflector >> Subject: Re: [

Re: [Elecraft] K3/0 Question

, > N2TK, Tony > > -Original Message- > From: elecraft-boun...@mailman.qth.net > [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Eric Swartz WA6HHQ > - > Elecraft > Sent: Sunday, May 19, 2013 4:32 PM > To: iain macdonnell - N6ML > Cc: Elecraft Reflector > S

Re: [Elecraft] K3/0 Question

rtz WA6HHQ - Elecraft Sent: Sunday, May 19, 2013 4:32 PM To: iain macdonnell - N6ML Cc: Elecraft Reflector Subject: Re: [Elecraft] K3/0 Question The K3/0 via the RemoteRig boxes absolutely -can- power up and down the remote K3. It uses a pin on the K3 AuxPort that acts the same as pressing the power button

Re: [Elecraft] K3/0 Question

3/10 I'm using and my friends K3/0 both used at control sites >> turn the >>>>> power On & Off to the K3/100 used at the radio site, so I expect that >> the >>>>> new "mini" K3/0 would as well. Suggest that you use an internet

Re: [Elecraft] K3/0 Question

;>> power On & Off to the K3/100 used at the radio site, so I expect that > the > >>> new "mini" K3/0 would as well. Suggest that you use an internet > controlled > >>> switch to turn on the AC to the 12 V power supply and then the "Power"

Re: [Elecraft] K3/0 Question

the AC to the 12 V power supply and then the "Power" >>> switch on the K3/0 will turn on and link to the K3/100. It all works very >>> well. >>> >>> 73, Doug VE3MV >>> >>> >>> - Original Message - From: "Brian F. Wru

Re: [Elecraft] K3/0 Question

gt; switch on the K3/0 will turn on and link to the K3/100. It all works very >> well. >> >> 73, Doug VE3MV >> >> >> - Original Message - From: "Brian F. Wruble" >> To: "Elecraft Reflector" >> Sent: Sunday, May 19, 2013 7:41 AM

<    1   2   3   4   5   >