I reset the TRX and checked the VFO´s that there is no split. After that, I
switch the trx to a different frequency via the WSJTX-2.3.0 I get split
frequencies.
Am Donnerstag, 18. Februar 2021, 08:36:19 MEZ hat Dirk Kuschke
Folgendes geschrieben:
I understood that and also
I understood that and also checked it, unfortunately it doesn't solve the
problem.
It has not been set split by me in any memory of the TRX or the software.I only
wanted to use the frequencies from "Settings / Working Frequencies", which
worked properly without split up to version 2.2.2
73,
On 2/17/21 4:50 PM, ve...@napan.com wrote:
Hi Glenn and all,
... I can set Audio to Pulse for both Rx and TX in
wsjtx settings. Rx now works and decodes OK. I can switch modes no
problem. I can see wsjtx in the recording tab of pavucontrol. If
attempt to Tx via the Tune button (or Tx
Hello Bill
I reboot the computer to avoid other application take control of any com port,
same error.
73 de Alex, HB9DRI
From: Bill Somerville
Sent: Thursday, February 18, 2021 12:43 AM
To: wsjt-devel@lists.sourceforge.net
Subject: Re: [wsjt-devel] FW: BUG in WSJT-X 2.3 and 2.4rc1
You don’t know?
With all my respect Joe you know perfect what's going on here
73 de Alex, HB9DRI
-Original Message-
From: Joe Taylor
Sent: Thursday, February 18, 2021 5:41 AM
To: WSJT software development
Subject: Re: [wsjt-devel] FW: BUG in WSJT-X 2.3 and 2.4rc1 COM port
I do not
I assume you are pressing the band select button to store the setting in the
band stack?
VFOA and VFOB have their own separate band stacks.
So you may have to select each VFO and press the band select to store it.
Mike W9MDB
On Wednesday, February 17, 2021, 01:01:51 PM CST, Dirk
I played a bit tonight and if I select the actual device name ie
"alsa_output.usb-Burr-Brown_from_TI_USB_Audio_CODEC-00.analog-stero.2"
in wsjtx it works. It shows up in pavucontrol OK. If I select just Pulse
in wsjtx Audio it does not work. Now if I can find a way to make the
names friendlier
On 2/17/2021 5:02 AM, Black Michael via wsjt-devel wrote:
I've also verified that reducing the volume level to eliminate the
effect does not reduce the power out either. My LP-700 wattmeter shows
the same wattage with 0 or -3.0dB
That could be caused by AGC within the rig. Or it could be in
I do not know what prompted a gratuitous diatribe about the origins,
strengths, and limitations of WSJT, WSJT-X, and MAP65 on this email
reflector. Your forum hosts hardly need instruction on these topics,
since we developed these referenced programs and the digital protocols
that power them.
I normally just set wsjtx audio to Pulse and then connect it to the
proper sound device with pavucontrol. I will experiment some more
tonight. Something is wrong though because wsjtx cannot recover once Tx
is attempted and needs to be killed. Wish there was an error log of some
sort.
73
FWIW, I experience the exact same symptoms with WSJT-X v2.4.0-rc1 on Ubuntu
20.04 when I choose the default sound device. It doesn't matter what audio
device I set the default to (using Ubuntu settings).
I have an external USB sound card that I normally use. With WSJT-X audio
settings pointed
I had thought that too, but it is not the reasen, if I switched off the split
before, I get split again when switching over. I switched all bands through
with the software and switched split off, the next test, split was there again.
That's only since version 2.3.0 with 2.2.2 everything is as
Oddly, WSJT-X DOES show up in pavucontrol for me
I don't know why it wouldn't...
de AI8W
-BEGIN GEEK CODE BLOCK-
Version: 3.1
GCS/CM/CC/E/IT/TW d-@ s+:+ !a C++$@ UBLVSCX*(on)$>$ P++>$ L+++$ E+@
W++>$ N+++ o+@ K+++ w@ O+@ M-@ V@>$ PS+@ PE@ Y+ PGP++ t+ 5+ X++ R@* tv++
b+>$ DI++ D+
Thanks Stefan
I will try that tonight when I get home.
73
Glenn VE9GJ
On February 17, 2021 1:56:10 PM AST, Stefan HB9TMC wrote:
>dsnoop was selected by accident while taking the screenshot.
>I have selected the usb-BurrBrown device (the last two rows on the
>list).
>No problem with having it on
Hi Stefan
In your screenshot is dsnoop not an alsa device bypassing pulse? Does tx show
up in pavucontrol with that selection? Wsjtx does work if I use the hw: device
but my goal is to have it working with pulse. Pulse allows multiple apps or
instances to share the same source or sink.
BTW
Hi Alex,
one of the two serial ports is probably opened by another application.
73
Bill
G4WJS.
On 17/02/2021 17:38, Alex Artieda, HB9DRI wrote:
Hello Bill
This is the answer after execute the command:
C:\WSJT\wsjtx\bin>rigctld-wsjtx -m 3081 -r COM4 -s 19200 -p COM2 -P
RTS -Cptt_share=1
Hello Bill
This is the answer after execute the command:
C:\WSJT\wsjtx\bin>rigctld-wsjtx -m 3081 -r COM4 -s 19200 -p COM2 -P RTS
-Cptt_share=1
Recommend using --vfo switch for rigctld if client supports it
rigctl and netrigctl will automatically detect vfo mode
rig_open: error =
Hi Alex,
yes it will work exactly as you require.
73
Bill
G4WJS.
On 17/02/2021 16:29, Alex Artieda, HB9DRI wrote:
Hello Bill
I must PTT a external sequencer via a COM port, I cannot use PTT via
CAT because that will trigger the Radio 1^st , I must trigger the
external sequencer via a COM
I understand that but the problem is wsjtx TX or playback never shows up
in pavucontrol Playback tab. wsjtx Rx does show up in the Recording tab
OK
73 Glenn VE9GJ
On 2021-02-17 12:25, Topher Petty wrote:
in Pulseaudio, you need to select the input and output sources using
"pavucontrol".
Hello Bill
I must PTT a external sequencer via a COM port, I cannot use PTT via CAT
because that will trigger the Radio 1st, I must trigger the external sequencer
via a COM port 1st, then the sequencer has 4 events to manage antenna relays,
preamps, bias in the SSPA and for last PTT the
in Pulseaudio, you need to select the input and output sources using
"pavucontrol".
Just above and to the left of the wsjt-x volume control and level in
pavucontrol the device you're sending to is shown. Click that and select
your radio's sound device.
You should, then, see the radio start
Hi
I have been struggling to get wsjtx working on my Ubuntu 20.04 64bit
Desktop. When I started I had version 2.1.1 then upgraded to 2.3.0 but
there was no change in behavior. Rig is a FT991A using builtin USB sound
device. Cat works OK. I can set Audio to Pulse for both Rx and TX in
wsjtx
I've got a completely separate app that generates a sine wave and it does the
same thing.
Ergo...Windows bug. This was probably introduced several months ago and nobody
noticed.
Mike W9MDB
On Wednesday, February 17, 2021, 08:27:30 AM CST, Alan Groups
wrote:
Maybe use a
On 17/02/2021 15:03, Dirk Kuschke via wsjt-devel wrote:
Hello,
since FTDX version 2.3.0
my yaesu ftdx3000d changes to split mode when I change the frequency,
using the button on the left. Up to version WSJTX2.2.2 this was not
the case.
The settings are:
Inline-Bild Inline-Bild
I change
Hello,
sinceFTDX version 2.3.0
my yaesu ftdx3000d changes to split mode when I change the frequency,
using the button on the left. Up to version WSJTX2.2.2 this was not thecase.
The settings are:
Ichange the Databits between 7 or 8 and the Stop bits between 1 or 2 with
noeffect. The
Hi Alex,
OK, try this. Change "Settings->Radio->Rig" to "Hamlib NET rigctl" and
"Settings->Radio->PTT Method" to "CAT" for each WSJT-X instance you run.
Open a CMD prompt window and type the following command:
C:\WSJT\wsjtx\bin\rigctld-wsjtx -m 3081 -r COMx -s y -p COMz -P RTS
-Cptt_share=1
Hello Bill
Yes I use only 1 CAT controller transmitter, the IC-9700, I don’t have any
other CAT application accessing my Transceiver.
73 de Alex, HB9DRI
From: Bill Somerville
Sent: Wednesday, February 17, 2021 9:39 PM
To: wsjt-devel@lists.sourceforge.net
Subject: Re: [wsjt-devel]
On 17/02/2021 14:35, John Nelson via wsjt-devel wrote:
Bill,
I have guided David (via landline) to get wsjtx to launch. The immediate
problem appears to be a failure of wsjtx to be installed in the Applications
folder by using the normal installation procedure of dragging the WSJT-X icon
Alex,
let me try again as you have not answered my question. I will qualify it
a bit which may help.
Are you only using one CAT controlled transmitter and is that your IC-7900?
Do you have any other applications that require CAT access to your
transceiver(s)?
Note by CAT control I do not
Ted,
that's not going to work, you need to use the links listed at the bottom
of every message to remove yourself.
Neil, KN3ILZ
On 2/17/2021 6:52 AM, Ted Lawhead Jr wrote:
Please remove my e-mail address from your list.
___
wsjt-devel mailing
Bill,
I have guided David (via landline) to get wsjtx to launch. The immediate
problem appears to be a failure of wsjtx to be installed in the Applications
folder by using the normal installation procedure of dragging the WSJT-X icon
on top of the Applications icon in the dmg panel.This
Dear Bill
You said “I am still not understanding what you are doing”
I’m doing EME, not HF, we, the EME community, make JT protocol famous, since
more than 15 years I was devote, together with aprox, 300 people to use an
ADAPTIVE POLARIZATION SYSTEM, MAP65 appears later (10 years ago
Maybe use a completely different app on the same system and then see if
the distortion is still there?
Alan G0TLK
On 17/02/2021 13:02, Black Michael via wsjt-devel wrote:
Since I've also verified this on an IC-7300 with it's own USB sound
card seems it's a Windows bug. I think this is a
Hi Dave,
that's not what I would expect to see if you had dragged and dropped the
WSJT-X application bundle onto the /Applications folder. You should see
something like the attached text file.
73
Bill
G4WJS.
On 17/02/2021 13:52, David Schmocker wrote:
Hi Bill:
It seems you are always
Hi Bill:
It seems you are always working (never sleeping)! Thank you for your help.
Here’s permissions view you requested:
From: Bill Somerville
Reply-To: WSJT software development
Date: Wednesday, February 17, 2021 at 4:17 AM
To:
Subject: Re: [wsjt-devel] Running WSJT-X
Since I've also verified this on an IC-7300 with it's own USB sound card seems
it's a Windows bug. I think this is a recent Windows bug since I used to see
linear behavior on the Pwr slider so that reducing to -3dB would cut the power
in half...but no more
I've reported the problem to MS
From: Bill Somerville [mailto:g4...@classdesign.com]
Sent: 17. helmikuuta 2021 14:01
To: wsjt-devel@lists.sourceforge.net
Subject: Re: [wsjt-devel] Clipping
On 17/02/2021 11:49, Bill Somerville wrote:
On 17/02/2021 11:08, Reino Talarmo wrote:
>From: Bill Somerville
Please remove my e-mail address from your list.
___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
Depending on the settings, the waterfall does a visual dynamic
compression, such that very weak signals are still visible next to very
strong signals. I.e. a -70 dB signal is well visible next to a -3 dB signal.
That's a feature, not a bug ;)
73
Stefan
On 17.02.21 12:08, Reino Talarmo
On 17/02/2021 11:49, Bill Somerville wrote:
On 17/02/2021 11:08, Reino Talarmo wrote:
*>From:*Bill Somerville [mailto:g4...@classdesign.com]
*Sent:* 17. helmikuuta 2021 0:16
*To:* wsjt-devel@lists.sourceforge.net
*Subject:* Re: [wsjt-devel] Clipping
On 16/02/2021 22:10, Jim Brown wrote:
On 17/02/2021 11:08, Reino Talarmo wrote:
*>From:*Bill Somerville [mailto:g4...@classdesign.com]
*Sent:* 17. helmikuuta 2021 0:16
*To:* wsjt-devel@lists.sourceforge.net
*Subject:* Re: [wsjt-devel] Clipping
On 16/02/2021 22:10, Jim Brown wrote:
On 2/16/2021 2:01 PM, Bill Somerville wrote:
Alex,
the PTT sharing was only ever designed to work with setups not using CAT
control. Currently the only supported way to have CAT control shared by
multiple applications is to use a CAT server application like the Hamlib
rigctld or similar, that will implicitly share the PTT so this should
I use
http://www.eterlogic.com/Products.VSPE.html
No need to register, and supports 4 CAT connections to the VCP using
splitter to real comport.
I use it with wsjtx, Commander , N1MM and MMTTY. for the last years with
no issue.
On 17/2/21 9:07 pm, Alex Artieda, HB9DRI wrote:
Hello Bill
>From: Bill Somerville [mailto:g4...@classdesign.com]
Sent: 17. helmikuuta 2021 0:16
To: wsjt-devel@lists.sourceforge.net
Subject: Re: [wsjt-devel] Clipping
On 16/02/2021 22:10, Jim Brown wrote:
On 2/16/2021 2:01 PM, Bill Somerville wrote:
there are no analog audio stages involved. The
Hello Bill
I can omit to work with Omnirig BUT the IC-9700 config embedded in WSJT-X have
the same behavior that the PTT, only the 1st WSJT-X instance can manage, the
only way to have SHARE CAT com port was using Omnirig.
Regards
Alex, HB9DRI
From: Bill Somerville
Sent: Wednesday,
Hi Alex,
thanks for that.
OK, I now understand what is happening. The Hamlib configuration
overrides do not currently apply when using any form of CAT control
other than Hamlib, including via Omni-Rig. I will change that for the
next release.
Another option is not to use Omni-Rig, which
On 17/02/2021 01:57, David Schmocker wrote:
Hi Bill,
1) uninstalled all WSJT-X prior instances (v2.2.2, v2.3.0, and v2.4.0rc1) by
dragging icon from Applications folder into trash can
2) re-down loaded WSJT-X .dmg file
3) launched .dmg installer
4) carefully followed the G4KLA Readme.txt
When, I looked at them, I saw Bills version had a blank line removed,
and the the 1 encapsulated in "" like "1". The previous you had did not
have that.
On 17/2/21 6:07 pm, Alex Artieda, HB9DRI wrote:
Hello Bill
Sorry but the file you send me is exact to the code propose by Mike,
the code
Hello Bill
Sorry but the file you send me is exact to the code propose by Mike, the code
is the same and I copied in ALL WSJT-X instances I have and I cannot share the
PTT port.
My config in Radio tab in ALL WSJT-X instances:
For RIG: I use Omni Rig 2 where CAT is configure over a
49 matches
Mail list logo
