On 27/05/17 21:37, Jim Brown wrote:
> I've been using JT modes for about six years. You should ONLY use
> WSJT-X, which is the software developed under the supervision of WSJT
> inventor (and Nobel laureate) K1JT. All other versions are derived from
> his earlier work, and most are unauthorized.
Don't tell the kapton that has been decoupling the 2kV on the anode in my
500W 1296MHz amplifier for 12 years this!
Dave
WW2R
Date: Sat, 27 May 2017 14:13:58 -0700
From: Matt Zilmer
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KX2 Battery Question
Message-ID:
Hello Elecrafters,
I have a little mechanical nuisance with the legs of my KX3.
If I carefully tighten the screws, after a while the right leg can no longer be folded out
completely and the left leg wobbles.
Is there a solution to hold the underside of the transceiver in place AND to hold
I'm in the process of upgrading our club's K3, new synth, DSP and a stack of
small mods.
I've come up against an issue that's causing me some confusion. The mod for
the KPAIO3 consist of a small electrolytic capacitor soldered to two pins on
the KPAIO3 module. I have two versions of
Yes Ingo, you can use two washers on each leg's thumb-screw with the leg
sandwiched between the washers.
At least this works for me.
73
Ken - K0PP
On May 28, 2017 03:41, "Ingo Meyer, DK3RED" wrote:
> Hello Elecrafters,
>
>
> I have a little mechanical nuisance with the legs
I like WSJT-X but I use JTDX as much or more. It adds some interesting
features to the decoding. WSJT-X interface is a little more polished but
JTDX isn't bad.
Read about different versions and try them out before discounting them
because someone says so.
73,
Kev K4VD
On Sun, May 28, 2017 at
On Sun,5/28/2017 12:18 AM, Richard Lamont wrote:
I agree with all of that, except the 'unauthorized' bit.
Joe has posted on that topic. The executive summary is that he is not
happy with the way in which some of those other developers have failed
to respect his license.
73, Jim K9YC
Hi,
My KPA500 started acting up and now does not amplify at all, and
the input SWR seems to bounce around. I did hear what sounded like an
arc (fairly loud bang, though it was the KAT500, not the KPA500) The
KAT500 is still working normal, but the KPA500 is bad, even into a dummy
Hello All.
My setup is, K3 (sn:5845), computer Athlon 2.5 GHz running WinXP, and homebrew
logging program.
Antennas, 40m e/f inv vee tuned through ATU on all bands, and 20/15m Bi-square
coax fed into shack.
Ground is 1/4 wave radials for each band, strapped together and connected to
ATU, K3
Gray,
Does your term "serial grnd" mean the RS-232 Signal Ground? If so, that
should not be connected to the enclosure ground.
As far as the K3 grnd goes, "bond" the K3 enclosure to the outside of
your interface box, and then on to the computer - follow the audio and
serial lines with the
Big point.
Once he releases the source code under GPL he has no recourse. These
developers can take his source code, do exactly what they want to it,
and don't even have to change the name of the application.
If the program was written with GPL tools, compilers, libraries, dll's,
etc..., as
Hi Ron.
Thanks for the confirmation. I figured out that Rev A was a mistake, after
looking at the fan connector and fan supply orientation. Had Rev A been used
it wouldn't have been a disaster, but the mod would have had no effect, as
it connected both ends of the capacitor to the positive
To expand just a bit, when commanding a QSY from the N1MM+ entry window,
the P3 seems to put that frequency in the center of the screen in
fixed-tune mode placing the edges +/- 10 KHz from it. If I QSY to
14050or 14070, which are the center of a 20 KHz boundary, the right and
left edges of the
You should tighten the screws after extending the legs. Get them tight.
Never fold the legs without loosening the thumb screws first! One leg will
tighten more if don't loosen the screws first.
This problem could have been eliminated if they had use a left hand thread on
one of the legs.
I'd like to get a directional coupler to, among other things, monitor my
transmit signal on a scope.
The Elecraft CP1 kit is priced well, but I'd want it in a metal box with
panel mount connectors, SO-239 for the main RF path. I'd also rather
use 50 ohm terminators rather than switches, so
Greetings,
I'm looking for a little practical advice about linear amplification for
the KX2/3 (I have both).
Hardrock-50 or KXPA100.
Essentially, it would be used mobile, although taking it out the car and
using it portable is
possible.
So any information from users of these two amps will
I looked into that very question a few months ago (February)…
My comments:
1. I don’t think Hardrock-50 has an auto-tuner so in pricing comparison,
compare with
a separate vendors auto-tuner (as good as Elecraft’s) if you are assuming
buying the KXPA100 with
auto tuner.
2. Hardrock-50 is
Thanks Alan. I just verified that this happens only when I QSY by typing
a frequency into the N1MM+ entry window. Problem resolved.
73,
Fred ("Skip") K6DGW
Sparks NV USA
Washoe County DM09dn
On 5/27/2017 8:41 PM, Alan wrote:
If N1MM changes the K3 VFO frequency, even temporarily, it could
Phil,
The Hardrock 50 has an atu - I don't know if the toroids are pre-wound
or not - if not, that's an
issue for me.
Actually, I'm kind of in the reverse situation - I want to keep my
KX2/3, but get rid of my FT-450D
- which is a nice radio, but it's bigger than I can use mobile.
All
Got two KX3 radios sitting here. Both in USB mode. On one, pressing the
keyer/mic button switches the display between swr/rf and cmp/alc. On the
other radio pressing keyer/mic it switches between showing mic gain and wpm
in vfo b, but always shows cmp/alc.
What are we missing?
73,
-detrick
Greetings,
First, before I go any further, I have nothing but the highest regard
for Elecraft's Customer
Support and Service. I've had several issues with my KX2 that were due
to operator error
and Elecraft has fixed my self-induced KX2 injuries quickly and
efficiently. Plus, I've had
a
As a relatively new owner of an Elecraft KX3 and all related accessories
this list has been of immense help to me. It is far more interesting and
well behaved than some other ham lists I read. When I did sell an Elecraft
manufactured accessory it sold in one hour.at my stated fair price and I
When I priced them, the Hardrock was just about half the cost for half the
power. I got the KXPA100.
The KXPA100 kit is assembly, no soldering. One of the design goals was for
installation as a remote PA for mobile use. Install the KXPA next to the
antenna and keep the KX3 by you.
wunder
Tom ...
I feel your pain but not your conclusion. For me the post-loosening problem
was solved with Loctite Blue. Since that didn't work for you, Loctite Red is
the next logical step. If that doesn't work, JB Weld most certainly will.
Just a drop of either adhesive coating the entire shank
Call Elecraft support!
Sent from my iPhone
...nr4c. bill
> On May 28, 2017, at 6:42 AM, Gordon LaPoint wrote:
>
> Hi,
>
> My KPA500 started acting up and now does not amplify at all, and the
> input SWR seems to bounce around. I did hear what sounded like an
Hi Alan:
Use Rev B. Rev A of the instructions had an error that was corrected by an
errata. Apparently you don't have that errata. The change was subsequently
included in the Rev B printing.
73, Ron AC7AC
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On
Using a GPLed compiler and most of the GPL tools doesn't result in a
requirement to licence under the GPL. In particularly, gcc is often
used to compile proprietary code.
Using GPL libraries does, except where those libraries implement
functions that would normally be included with an
note : personal reply
Wow ... somebody writing an off topic post (it had nothing to do with
Elecraft products) to complain about off topic posts. Talk about
dripping with irony.
Besides, it is a trivial exercise to speed read through the topic
headers and delete the messages you don't
I agree 100%! It's really a form of bullying censorship. Learn how to set up
rules in your e-mail client. Failing that, use the 'Del' key. Geez!
Imagine coming across a QSO ota that we don't want to participate in. Rather
than QSY, we ask the active participants to cease their QSO. Ick!
73 de
--
I believe both kinds of views are valid, this coming from a confessed but
unabashed occasional OT-committer. For some the reflector is a source of
technical information and exchange about Elecraft products. Period. Nothing
wrong with that. For others –
Mike,
Look in the manual at Reset to Factory Defaults - or EEINIT.
Caution, it will wipe out configuration data, so be sure you have a
saved configuration file from a time all was OK so you can restore it
after the reset.
73,
Don W3FPR
On 5/28/2017 6:29 PM, Mike Morrell wrote:
Folks:
Can
Ted and all,
I am in agreement with you. There is benefit in many OT conversations,
and thankfully Eric allows it. We learn many things about ham radio in
general as well as how it applies to Elecraft radios (even if it is only
about operating/conditions at the time). There are many OT
It would be pretty easy to modify the CP-1 to use SO239 connectors and mount it
in a box. I would do it while building the board - drill four holes in the
corners for mounting, mount the SO-239s on the box and wire them to the board.
But, I would also keep the BNC connectors for the test
Folks:
Can a "hard reset" be performed on the KX2?
I cannot seem to find that command in the manual.
Thanks,
Mike, K8KE
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Just ran across this the other day. Anyone know have any experience with
this amp?
http://www.ebay.com/itm/Xiegu-XPA125-QRP-ALC-Antenna-Tuner-Function-125W-HF-Ham-Radio-Power-Amplifier-US-/132206081348?hash=item1ec818b544:g:cVQAAOSw9OFZKOkD
73 Tex
ka5y
--
View this message in context:
It's Chinese, YMMV. The BOGO offer seems strange for ham radio
equipment. Of course, you could always put two into a combiner and get
250 W from a 10 W exciter. [:-) It's in the US, no specslisted,
5W-->125 W is 13.97 dB gain. Doesn't say it runs on nominal 12VDC. I
have no experience and
The writer of the manual has a sense of humor. You can download the
manual, and on the last page of the "Troubleshooting" section the last
problem listed is: "Smoke comes from unit," and the solution, "Replace
the smoke...only kidding, return to dealer."
On 5/28/2017 7:15 PM, pkhjr via
These guys have several. Well built. Not cheap. http://www.preciserf.com
Mike KD8RQE
In a message dated 5/28/2017 1:25:49 P.M. Eastern Daylight Time,
mike.ab...@gmail.com writes:
I'd like to get a directional coupler to, among other things, monitor my
transmit signal on a scope.
The
Would this work? It comes with N connectors
http://www.ebay.com/itm/Mini-Circuits-ZFDC-20-4-N-Coaxial-Directional-Coupler-1-1000MHz-/263005332237?hash=item3d3c56e30d:g:YS4AAOSwK6RZKIqL
Mike va3mw
On Sun, May 28, 2017 at 8:39 PM, Mike via Elecraft wrote:
> These
39 matches
Mail list logo