If the post is about a problem I can respond with an answer, I normally
"reply to all" so the list is updated, and I know that a copy is sent to
the poster.
Maybe my thinking is off, but I do not consider that as generating spam.
73,
Don W3FPR
On 12/28/2020 4:59 PM, Jim Brown wrote:
FWIW,
Alan,
My Thunderbird does not work like that - If I select "Reply to List", it
puts my email address in the Reply-to field and in the To field, it puts
the elecraft list address.
73,
Don W3FPR
On 12/28/2020 4:30 PM, Alan Bloom wrote:
I'm also using Thunderbird, but when I chose "Reply List"
Bret,
No way that I know of, Mode is a per band setting.
73,
Don W3FPR
On 12/27/2020 1:17 PM, MaverickNH wrote:
If I want to apply CW Mode and configuration settings across all bands,
rather than each band individually, is there a way to do that?
Dana,
It likely means ---
1 - You don't need the preamp on that band.
2 - You have not set S-MTR ABS (S-meter absolute) on in the menu.
Other than those things, I cannot think of anything else - other than
the remote possibility that you have a noisy preamp.
73,
Don W3FPR
On 12/26/2020 4:44
John,
To keep up with all the changes, you should read the firmware release
notes too. Mark up the manual with that information.
73,
Don W3FPR
On 12/26/2020 12:47 PM, John Lemay wrote:
Ken
Thanks for replying quickly.
I am reading the current (D10 version) manual, but on
Frank,
No way that I know of. I always grabbed the manual and manually set
everything back to defaults.
73,
Don W3FPR
On 12/25/2020 10:56 AM, Frank Krozel wrote:
Is there an easy way to reset the KDSP-2 for the K2?
-73- FrankKG9H
I really like that quote from Albert Einstein.
Ignorance can be cured with information, but stupidity lives on in its
dismissal of facts and information.
Merry Christmas all, stay safe.
73,
Don W3FPR
On 12/23/2020 7:12 PM, David Ferrington, M0XDF wrote:
The difference between genius and
Jerry,
I too can state that 1st class or priority mail to Alaska and Hawaii is
the same as the lower 48. You can also ship to Puerto Rico for the
same cost.
73,
Don W3FPR
On 12/21/2020 8:15 PM, w...@jetbroadband.com wrote:
Greetings all,
Doing some end of the year clearing out
Pat,
I do not believe they are interchangeable. Contact supp...@elecraft.com
and they can provide some test points to help analyze the problem.
73,
Don W3FPR
On 12/21/2020 11:36 AM, Ing. Pasquale Speranza wrote:
I have a problem on my K3S. Suddenly in SSB the radio started producing
Tony,
The K3/K3S is a very good transceiver. I can't answer your question
about the speaker jack, but I assume it is because of the lighting in
the photos. You can easily replace the SO-239 jacks with the connector
of your choice, but IMHO it will not make any difference. I once
changed
if it comes back.
On Dec 7, 2020, at 11:43 AM, Don Wilhelm wrote:
Bill,
It does sound like it is fixed. Just be aware that some intermittents do find
their way back, so knowing the symptoms you can recognize it quickly.
73,
Don W3FPR
On 12/6/2020 6:30 PM, Bill Coleman wrote:
Don,
I set the K2 up
John,
Is there any chance that you tuned the VFO from another band (maybe 12
meters) into the 10 meter band? Try a Direct Frequency Entry into the
10 meter band and see if it comes back.
73,
Don W3FPR
On 12/15/2020 1:35 PM, John Kountz wrote:
Gentlemen,
There seems to have been ambiguity
Luc and all,
I have been informed that simply clicking the link I sent may give a 404
error because somehow a period is picked up as part of the link.
Simply remove the period and it will work fine.
73,
Don W3FPR
On 12/13/2020 12:13 PM, Don Wilhelm wrote:
Luc,
The short answer
Luc,
The short answer is that will not work.
What you need is an open circuit on receive and a short to ground during
transmit.
Take a look at the K2(BASIC) External T-R Relay Driver on Tom Hammond's
(SK) website http://www.mmccs.com/mmarc/n0ss/index_k2.html. Kits are
now available from
Eric,
Yes, they are wired the same - see the KIO2 manual.
73,
Don W3FPR
On 12/12/2020 2:27 PM, eric norris wrote:
Don, et al,
Can I assume the same is true of a K2/10 with the AUX IO option? Are
they wired the same?
__
Eric,
The KPA100 RS-232 data appears on pins 2 and 3 of the AUX IO connector
with pin 5 being RS-232 Signal Ground. Chassis ground is on pin 1. See
the KPA100 manual.
DO NOT connect to any other pins of the AUX IO connector, those are
internal K2 signals to be used by external devices such
Joe,
Do you have the audio levels set right for transmit?
Go to my webpage www.w3fpr.com and look at the last article in the left
column.
73,
Don W3FPR
On 12/11/2020 3:10 PM, Joe K2UF wrote:
I am trying to get FT8 running on my K3 using Rig blaster advantage.
Everything works except no
Bill,
It does sound like it is fixed. Just be aware that some intermittents
do find their way back, so knowing the symptoms you can recognize it
quickly.
73,
Don W3FPR
On 12/6/2020 6:30 PM, Bill Coleman wrote:
Don,
I set the K2 up this weekend to try to reproduce this problem. Once again
Joe,
The XMIT button does not produce any RF nor switch the mode.
It is like a front panel PTT switch, but tap on and tap off.
If you do a TUNE (hold the button for 2 seconds), it will go to CW mode
and produce output (no key needed).
73,
Don W3FPR
On 12/4/2020 8:32 AM, Joseph McIntire
Kent,
I bought some on Ebay about 3 years ago.
The old ones from my Heathkit days were split and no longer held the nuts.
73,
Don W3FPR
On 12/2/2020 3:53 PM, KENT TRIMBLE wrote:
That's been suggested to Elecraft many times over the past 21 years.
Wonder if anyone still makes them.
My three
Arkady,
Is Q3 properly seated on the heatsink with its thermal pad and mounting
screw? That is the device which senses the temperature.
73,
Don W3FPR
On 11/30/2020 5:00 PM, Arkady via Elecraft wrote:
Hello,
I wonder if anybody had similar problem.
When I “run” I get fan starting running
Bill,
It is also a mystery to me that it is intermittent rather than a solid
failure. That might imply that something is breaking into oscillation
and overwhelming the VRFDET line. That is why I suggested you check the
component placement and the diode orientation.
That intermittent
Bill,
You might want to inspect the K60XV soldering carefully for bridges and
anything unsoldered.
When this fault condition occurs, what is the voltage on K60XV P1 pin 6.
If VRFDET becomes active during receive, the K2 may behave as you
describe because the firmware 'thinks' the K2 is
Dick,
You can order the power cable from Elecraft.
The part number is KPCA-F, it has an APP connector on one end and ring
terminals on the other end. The wire is 12 guage.
73,
Don W3FPR
On 11/28/2020 2:57 PM, RVZ via Elecraft wrote:
Hi Guys,
Please advise what options I have for
Jim,
That may work OK for non-Elecraft gear, but with the power control
mechanism used by Elecraft, not having sufficient audio drive will cause
"power hunting". Drive the soundcard audio for digital modes to 4 bars
solid with the 5th flashing on the ALC meter. Then set the power knob
for
The phrase "run a DERIVATION of an open source operating system" is key.
It is just a basis for their software. I would bet not a one of them
would open up the full source code used on their hardware. They might
reveal which open source operating system they based their software on,
but not
Dave,
If I am not mistaken, that board would be installed in a K3 that did not
have an ATU.
If you bought the K3 without the tuner and later installed the tuner,
that would be the reason you have it in your 'junk'.
73,
Don W3FPR
On 11/26/2020 6:03 PM, David Olean wrote:
I hope someone can
Doug,
I lived through cycle 19 of the sunspot signals, and did not find any
problem with receiver overloading at that time. We did not have the
Elecraft gear at that time, but what we had was not up to the
performance/protection that is typical for Elecraft. Receivers have
gotten much
Philip,
What kind of a building are you in? As an example, I live in a stucco
house, and with the wire on the walls before the stucco went on, I live
in a faraday shield and few if any signals are received inside the
house. That does include cellphone signals as well as ham frequencies.
Lyn,
I think you are 'getting caught up in the semantics' - let me try a
brief explanation.
Once the tuner knows the proper L/C combination for each frequency bin,
it will switch to those settings in MAN mode. It will NOT try to autotune.
If you switch to a different antenna on that
Jim,
Yes, anything plugged into Line In overrides the internal soundcard
input. That is by design.
BTW, you can have several applications running at once on a single
soundcard - you might try that. The multiple sources are mixed by the
soundcard. The internal soundcard is good enough for
Phil,
Do you have the counterpoise wire connected to a screw on the KX2?
The AX1 is not much of an antenna without it.
73,
Don W3FPR
On 11/23/2020 3:27 PM, Philip Cochran wrote:
I tried 80, 40, 20, 17, and 10 meter ham bands. I tried WWV on 5, 10, 15, and
20 MHz. I tried the common SWL
I do not know what mauve is either.
My wife says I had only 8 crayons in my box while she had 64!
I am amazed at her color perception and memory. She can look at a color
and go to the store and have them duplicate it exactly - even without a
sample for matching.
Having done professional
Doug,
Try better lighting - I think you will find the center stripe is
actually red. Alternately, ask a woman to read the colors - their color
perception is usually much better than men's.
73,
Don W3FPR
On 11/22/2020 4:03 PM, Douglas Hagerman via Elecraft wrote:
I’m in the E850138 upgrade
Wes,
Download the XG3 manual and look near the end (just before the
schematic) and you will see the wiring for a substitute for the KXSER
cable. Build one and plug it into one of your RS232 ports.
73,
Don W3FPR
On 11/22/2020 2:59 PM, Wes wrote:
Somehow I misplaced the data cable used to
Steve,
Are you measuring with the amplifier connected? That could be a reason.
Put in a plug with nothing connected and remeasure. Be careful with
autoranging meters, they can fool you. Make certain you know what your
meter displays for infinite resistance - it should be the same as shown
Barry,
Check the soldering for the LCD display pins. I would also check
continuity on Front Panel U1 to the display pins. Should you find any
that do not have continuity, do not lift the LCD to reflow the solder,
instead, carve a notch in the socket and solder it from on the socket side.
John,
The K2/10 does not have a KEYOUT signal, so you would have to add one to
key the KXPA100 (it is not a kit available from Elecraft). You can see
what needs to be added at http://www.mmccs.com/mmarc/n0ss/index_k2.html
- scroll down to K2 (basic) External T-R Relay Driver. Contrary to
Does the same thing happen if you disconnect the computer?
73,
Don W3FPR
On 11/19/2020 10:07 AM, w...@jetbroadband.com wrote:
GM All,
I have something very unusual going on with both of my K3 radios. I set the
CONFIG PTT-KEY parameter to RTS- DTR and the parameter does not change when
I
...
I am sure it will come back, as I have seen it before...
73, and thanks,
Dave (NK7Z)
https://www.nk7z.net
ARRL Volunteer Examiner
ARRL Technical Specialist, RFI
ARRL Asst. Director, NW Division, Technical Resources
On 11/18/20 1:38 PM, Don Wilhelm wrote:
Dave,
Are you running with the KAT500
Dave,
Are you running with the KAT500 in MAN or TUN?
After you have trained the KAT500 to the antenna (see the manual for the
bin sizes for each band), you should switch it to MANual. That will
keep it from trying to TUNe when you first transmit.
73,
Don W3FPR
On 11/18/2020 2:56 PM, Dave
Wes,
The answer is NO. The KAT500 and KPA500 take their AUX commands from
the K3(S).
On 11/17/2020 1:11 PM, Wes wrote:
I have a K3S interfaced to the KAT500 and KPA500 using the Aux cables.
If I was to replace the K3S with a rig with only RS232 control of the
KPA500, will the Kat500 still
Al,
The screw size is 6-32 (not metric).
But do contact Elecraft to obtain the proper screws. If the screws
project too far inside the KX3 enclosure, the PC board will be damaged.
I do know it can take a while to get items 'across the pond', but for
the health of your KX3, get the proper
Carlos,
You may have a bad copy of Spectrogram - you can download a good copy
from my website www.w3fpr.com. Both version 5.17 and version 16 are
there - scroll near the bottom of the home page to see the links.
I have been running version 16 on Windows 10 for some time.
73,
Don W3FPR
On
Bill,
I am not certain how your other radios determine whether the microphone
needs bias or not.
Yes, if you are using Icom with Icom mics, those need bias.
If you are using Kenwood or Yaesu, they do not supply bias.
The bias or not question depends on the microphone used. Elecraft
allows
Dan,
The Tek 453 has two vertical input channels. Did you connect to the one
that is being displayed? Are you using a 10X probe?
Yes, you should see a square wave if you have the vertical amplitude and
the horizontal sweep set correctly.
73,
Don W3FPR
On 11/7/2020 3:47 PM, Dan Presley
Tom,
You will have to use the KEYOUT from the K2/100. The AUX cable will not
work with the K2.
73,
Don W3FPR
On 11/4/2020 10:12 PM, cx...@4email.net wrote:
Question: How compatible is the K2/100 with KAT/KPA500? Is it possible
to connect K2/100 to both of these other units with the
Don,
Why not replace the regulator and cross your fingers? If it works, all
is well. There is no firmware on the KIO2, but the MAX1406 U1 may have
been damaged.
73,
Don W3FPR
On 11/4/2020 10:09 AM, Don Zank via Elecraft wrote:
HiMy KIO2 interface has stopped working. Voltage checks
As any woodworker knows, that is what clamps are for - they provide that
extra hand often needed.
Also, the woodworker's mantra is "you can never have too many clamps" -
I have often found that is true.
There are large and quite small clamps.
73,
Don W3FPR
On 11/3/2020 4:55 PM, Paul Ferguson
John,
It sounds like you need to adjust the BFO settings for the FL1 SSB
filter. You can do that in receive.
It is best if you do that using a visual aid like an audio spectrum
analyzer to be able to see the position of the filter passband in the
audio spectrum. Spectrogram is one such
Dave,
First try the VCOSHLDKT from Elecraft. See my reflector post at 12:37
today.
Alternately, move anything containing a transformer 2 feet or more away
from the K2.
73,
Don W3FPR
On 10/30/2020 9:11 PM, DaveVK wrote:
Any suggestions to clean the CW transmission up would be
You can cure that condition by installing the VCOSHLDMD from Elecraft.
It adds a mu-metal shield around T5 so the transformer core is not
modulated by the magnetic field from the power supply transformer.
If you do install that mod, first adjust the T5 turns spacing and then
put the shield
The smoke detectors we have here are wired into the security system - no
replaceable batteries - except for one which is standalone in the
bedroom and was required to be added by the inspector when we built the
house even with the whole house system in place. No RFI problems observed.
We do
Bryan intended this to go to the reflector. See below:
73,
Don W3FPR
Forwarded Message
Subject:Re: [Elecraft] K2 upgrade kit sequence
Date: Thu, 29 Oct 2020 17:41:33 + (UTC)
From: Bryan Nehl
To: Don Wilhelm
Don,
While the keying mod kit instructions
Well, regular reflector email works well, and is my preference If it is
changed, I will go down "kicking and screaming". Threads lose something
for me - subjects change, but participants do not change the subject
line, so things get mixed up.
If you want threading a good email client like
John,
I hope you do not bite your tongue while you have it firmly planted in
your cheek.
73,
Don W3FPR
On 10/28/2020 5:10 PM, John Harper wrote:
I think California's Health & Human Services Dept has banned bragging about
having received California products. If not, it will soon be added to
Doug,
You are exactly right. If you follow the K2 history, you will find that
the K2 A TO B kit was issued to pull all the prior mods together as well
as providing instructions about the best sequence to use when doing a
full upgrade. That happened at the same time the B level boards were
David and all,
I am a little late chiming in here, but all David's points are correct
except for a caution on one.
The alternate winding ratio for T4 should never be used with the KSB2 or
the KPA100 installed. It is OK for power in CW kept below 5 watts.
If the PA is operated above 5 watts,
Dan,
The K2 BNC jack will have a DC path to ground whether the K160RX is
installed or not. It is not "ground" for RF, but will show a low DC
path to ground if you measure it with your DMM. If you disconnect lead
3 or 4 of T4, the DC short to ground will go away.
73,
Don W3FPR
On
Carlos,
Do you have the internal frequency counter probe plugged into TP2? That
is one possible cause, remove it and retest. CW or SSB mode? All
spurious signals should be greater than 43 dB below the carrier level -
they cannot be expressed meaningfully in dBm, only with respect to the
Gmail is doing that for you. They do you the "favor" of not repeating
what you sent. Several folks have posted questions about that behavior.
73,
Don W3FPR
On 10/20/2020 12:28 PM, Rich NE1EE wrote:
Despite having the correct settings, I have not been receiving my own posts,
and, because I
Jim,
If your KPA500 is older, there was a change to the transformer mounting
which added a couple washers to the assembly - both under and above the
transformer. Contact supp...@elecraft.com for details and availability
of the kit.
On 2020-10-20 8:11, jimn4kh wrote:
I wasn't my
Carlos,
If you change the filter width, you will also have to change the BFO
settings to keep the passband centered at your desired sidetone pitch.
73,
Don W3FPR
On 10/20/2020 3:35 AM, carlos popelier wrote:
for the cw filter values in cw like fl2 0.70 is this 700hz?
and if you make a
Ray,
I don't know about any software, but the latest firmware is available -
the most recent is MCU 2.04, IOC 1.09 They must go together - order as
FWK2MCIO. If you have trouble finding it on the website, just email
sa...@elecraft.com to order.
To find your currently installed K2 firmware
Dennis,
Frequency data is available from the RS-232 data, but needs decoding
which implies that a smart device is needed (computer). See the K3
Programmer's Reference Manual for the commands and responses.
73,
Don W3FPR
On 10/18/2020 2:28 PM, Dennis Ashworth wrote:
I operate a vertical
Date: Sat, 17 Oct 2020 13:11:23 -0400
From: Don Wilhelm
Reply-To: donw...@embarqmail.com
To: w2bvh
Lenny,
In my experience with over 1000 K2 repairs, I have never seen anything
like that. But I would look first at the PLL/VCO area, and possibility
the BFO.
If you have a good monitor
Jack,
This fault has been reported several times and usually turns out to be a
problem in the KPA500 T/R switch area.
I suggest you consult with supp...@elecraft.com for guidance on how to
proceed (fix it yourself or send it in for repair).
73,
Don W3FPR
On 10/15/2020 6:34 PM,
Geert,
The kits that Ron WB3AAL (SK) offered were exactly the same kit as Tom
Hammond N0SS (SK) offered. Tom passed the baton to Ron for the kits
some long time ago (2015 or 2016). Ron added nothing, and in fact
offered Tom's documentation for the instructions. One thing that Ron
did add
Trustee
Mid-MO ARC
Jefferson City, MO
On 10/15/2020 12:32 PM, Don Wilhelm wrote:
Despite what hat website says, there are no kits available. Tom
Hammond was SK several years ago, but his local radio club has
preserved the content on his website.
All the instructions are there, and I believe Tom used
Pete,
I would say re-tune after switching with the external antenna switch.
If you have tuned to one antenna (on a single port), and then change the
load slightly (by switching to the other antenna), a re-tune is necessary.
73,
Don W3FPR
On 10/15/2020 3:17 PM, N4ZR wrote:
I have two antennas
Despite what hat website says, there are no kits available. Tom Hammond
was SK several years ago, but his local radio club has preserved the
content on his website.
All the instructions are there, and I believe Tom used FAR Circuits for
his boards. An email to FAR Circuits may turn up a board
Richard,
I don't know the answer, but when you get receiver sensitivities better
the -135dBm, the exact sensitivity numbers do not mean much unless you
have an extremely quiet location.
In general, the local noise will mask anything lower than -135dBm.
I expect all K4s models to have better
in the shack.
Do you concur?
I’m in the process of a number of shack improvements, including antenna
replacements and grounding and bonding, so that might take care of it.
On Jan 11, 2020, at 11:29 AM, Don Wilhelm wrote:
Bill,
Is this into a dummy load (bypass the ATU or tune the ATU
Bryan,
I would first check the mic wiring for a broken or otherwise faulty
ground wire.
73,
Don W3FPR
On 10/9/2020 1:14 PM, Bryan Savill wrote:
Here's my issue and it has just begun.
I'm using a Heil Proset with my K3s, when I switch to VOX the tx LED
lights with no input.
With the headset
Istvan,
There are protective diodes in series with both the internal batteries
and the external supply, so the fact that the KX3 shows 0.3 to 0.4 volts
lower than the external supply is normal.
73,
Don W3FPR
On 10/8/2020 2:53 AM, István Szabó wrote:
When I plug in the 13.8V PS the radio
Tom,
You likely have the 6 (or 13) kHz filter enabled for both DATA and AM
modes. Use K3 Utility Filter Calibration to change it.
73,
Don W3FPR
On 10/6/2020 6:25 PM, Tom Azlin W7SUA wrote:
Hi.
My K3 seems to switch to AM around 5 MHz even though the display says
DATA. And the filter
So how did KDKA in Pittsburgh, Pa become a Western callsign?
73,
Don W3FPR
On 10/6/2020 1:04 PM, a...@elecraft.com wrote:
More than you ever wanted to know about the convention of giving "W"
callsigns to broadcast stations east of the Mississippi and "K"
callsigns to the west:
Doug,
Do the K2ATOBKT first, and where those instructions indicate, do the
BFOMDKT and the other auxiliary kits. That will synchronize them for you.
73,
Don W3FPR
On 10/5/2020 4:55 PM, Douglas Hagerman via Elecraft wrote:
It turns out that the 82 pF cap I was looking for in the BFOMDKT kit
Mike,
Easy with Thunderbird,
Make a filter for your incoming mail - If the subject line contains K4,
move it to whichever folder you would like.
That will work as long as everyone puts 'K4' in the subject line. For
the rest, you will have to use the Delete key.
73,
Don W3FPR
On
Carlos,
That sounds like a toroid in the Low Pass Filter. If so, yes you could
make that substitution if it fits.
73,
Don W3FPR
On 10/5/2020 6:35 AM, carlos popelier wrote:
hi, can it be replaced by t50-10 or equivalent
carlos on6cn
Doug,
I have doubts that the toroid for L33 has been changed.
C174 should be 82pF - call support to get a proper capacitor.
Do not remove turns from L33.
The BFO should come into range with those values. Check the high and
low frequencies before doing anything else.
73,
Don W3FPR
On
Fernando,
They should be about the same. They use different cases, but the
insides are the same - an electret mic element.
The MH4 was introduced only because the case for the MH2 was no longer
available.
73,
Don W3FPR
On 9/28/2020 10:09 AM, Fernando Sindeaux wrote:
Dear Friends,
Which
Bill,
Unplug and replug all options in the K2 as a first try, also try
removing the cable to the KAT100. If it is the KAT100, try shortening
the cable between the KPA100 and the KAT100.
INFO 080 means that one of the option's firmware is not communicating
with the K2 MCU (or in the case of
Eric,
Yes to both.
73,
Don W3FPR
On 9/27/2020 7:04 PM, eric norris via Elecraft wrote:
Will an MH2 mic work with a K3S, and will an MH4 mic work with a K2?
Thanks,
73, Eric WD6DBM

__
Elecraft mailing list
Home:
Mike,
Connector #22 is a USB port for a keyboard, not a general USB port. It
is clearly labeled "KEYBOARD".
73,
Don W3FPR
On 9/26/2020 7:21 PM, Mike Flowers wrote:
I have successfully captured a P3 screen image.
Elecraft P3 Utility > Capture Image Tab> Capture Image button - this captures
layout for each of them.
73,
Don W3FPR
On 9/25/2020 8:35 PM, qr...@roadrunner.com wrote:
Mark,
Do you have a schematic for the XV222? I looked on their site and
could not come up with one.
72
Howard Kraus, K2UD
-
From: "Don Wilhelm"
To:
Mark,
Sorry about your failed effort. There is little in the RX path other
than Q3 and U1 that is not also used in TX.
If you have equipment that can do signal tracing at 222MHz, just trace
the signal path. There should be a significant increase in RF voltage
at the output of Q3 and more
Doug,
This is one of the problems with using info from the wayback machine.
That was one initial 'cure' that worked only marginally.
Elecraft released a mod kit that works well. Put the parts from the kit
in, and yes, C180 is to be removed in the process.
Go back to setting L34 for best S/N
Tom,
I would say 100 feet if you are running 100 watts. If you increase the
power, the distance should be increased. As is often said in cases like
this 'it all depends'.
I am assuming you are using the OCFD as a receive antenna. If you hear
the COR clicking while transmitting, they are
Mark,
Replacing those components will normally restore receive.
73
Don W3FPR
On 9/17/2020 8:57 PM, k2qo wrote:
During the recent September VHF contest I could only hear the absolute
strongest local stations on the XV222/K3 in my rover. It worked FB in June.
My XV432 worked just OK as usual.
Barry,
That can happen if you ran CAL PLL with the bottom cover off. Try it again.
73,
Don W3FPR
On 9/15/2020 8:38 PM, barry halterman wrote:
Greetings folks. My K2 has a snapping sound when tuning the band regardless
of mode and it seems to happen when I am close to a signal...within 4 khz
Doug,
If you have the most current upgrade kits, there is no overlap. OTOH if
you have older upgrade kits such as the BFO upgrade, there were changes.
73,
Don W3FPR
On 9/14/2020 7:49 PM, Douglas Hagerman via Elecraft wrote:
I am starting to apply the accumulated Elecraft upgrades to an
It takes 20+ watts to tune the KAT500.
I have no idea of how to set up the IC7300 to do that when in SSB mode.
You will have to ask on the Icom forums.
73,
Don W3FPR
On 9/12/2020 5:04 PM, Russell Domareck via Elecraft wrote:
I own a KAT500 and KPA500 that I use with an IC 7300. When in CW
Steve,
Most email clients include the ability to set filters. My Thunderbird
filters everything with [Elecraft] in the subject line into my Elecraft
sub-box under my Inbox. I can then reply to (or delete) any post I
choose to. My account is set to send individual emails.
In other words, I
Andre,
Do you have any power control? To check set the power to about 50 watts
and do a TUNE. Measure the actual power output with an in-line
wattmeter and a 50 ohm dummy load.
If it still goes to 160 watts, you do not have any power control. The
usual reason is the diodes D16 and D17
Joe,
You cannot get more official than what Wayne says.
73,
Don W3FPR
On 9/1/2020 5:11 PM, Joseph Trombino, Jr wrote:
Howdy Gang.
Just saw a note from Wayne (on another subject) indicating that a small number
of K4’s will ship this week.
Has Elecraft officially said that K4 shipping is
Chris,
I suspect that artifact is being introduced by the Speech Processor on
the KSB2 board.
Do you know any locals who have a K2? The quickest way to verify my
suspicion is to swap out the KSB2 board.
BTW - TUNE switches to CW even if in SSB mode.
73,
Don W3FPR
On 8/30/2020 1:07 PM,
Joe,
The telling answer is in your statement "the radio has an internal ATU".
The radio is showing the SWR between the radio and the ATU.
The wattmeter is showing you the SWR after the ATU - in other words, the
SWR of the untuned antenna. So there may be nothing wrong.
Connect a dummy load
David,
As someone else suggested, it sounds a lot like RF feedback on 17m.
Try operating into a dummy load to see if the same thing happens - if
not, get out the ferrites.
73,
Don W3FPR
On 8/27/2020 12:41 PM, David Haines wrote:
Here are more details:
All seems to be working fine on
Joe,
That was the goal, but consider that the fires may have impacted the
schedule.
Shipping one on the last day of the month meets the qualification.
Be patient until Eric updates us.
Stay safe, and if you are in the Western states, stay away from the fires.
73,
Don W3FPR
On 8/26/2020 1:51
201 - 300 of 14022 matches
Mail list logo