On Fri, 11 Jun 2021, John Dammeyer wrote:
Date: Fri, 11 Jun 2021 17:05:53 -0700
From: John Dammeyer
Reply-To: "Enhanced Machine Controller (EMC)"
To: "'Enhanced Machine Controller (EMC)'"
Subject: Re: [Emc-users] Pi4 issues with MESA 7i92H
From: Ralph Stirling
suggests some kind of network setup issue on your RPI
Did you try setting the host address to 10.10.10.100 and the 7I92 to 10.10.10.10
This is less likely to have routing issues (and is suggested in general to
avoid overlaps with common NAT ranges)
-Original Message-
From: Peter
I dont see this issue (though if have my 7I92 at 10.10.10.10 and the RPI at
10.10.10.100)
pi@raspberrypi:/boot $ uname -a
Linux raspberrypi 4.19.71-rt24-v7l+ #1 SMP PREEMPT RT Thu Jan 23 16:59:28 PST
2020 armv7l GNU/Linux
pi@raspberrypi:/boot $ mesaflash --device 7i92 --addr 10.10.10.10
On Thu, 10 Jun 2021, John Dammeyer wrote:
Date: Thu, 10 Jun 2021 21:25:35 -0700
From: John Dammeyer
Reply-To: "Enhanced Machine Controller (EMC)"
To: "'Enhanced Machine Controller (EMC)'"
Subject: Re: [Emc-users] Pi4 issues with MESA 7i92H
BTW, used the same process for the BBB to
w
what hm2_rpspi has implemented.
________
From: Peter C. Wallace [p...@mesanet.com]
Sent: Thursday, June 10, 2021 11:56 AM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Multiple 7i90 cards on Rpi 4b
On Thu, 10 Jun 2021, Ralph Stirling wrote:
Date: Thu,
On Thu, 10 Jun 2021, Ralph Stirling wrote:
Date: Thu, 10 Jun 2021 14:58:24 +
From: Ralph Stirling
Reply-To: "Enhanced Machine Controller (EMC)"
To: "emc-users@lists.sourceforge.net"
Subject: [Emc-users] Multiple 7i90 cards on Rpi 4b
The man page for hm2_rpspi indicates that multiple
On Wed, 2 Jun 2021, Fox Mulder wrote:
Date: Wed, 2 Jun 2021 20:06:05 +0200
From: Fox Mulder
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] How to change step pulse width for stepper driver
So i tried setting stepspace = 1
On Sat, 22 May 2021, dave engvall wrote:
Date: Sat, 22 May 2021 17:12:35 -0700
From: dave engvall
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] homing off glass scale
Talk about having a bad day. Sure glad the extras were
On Thu, 29 Apr 2021, Curtis Dutton wrote:
Date: Thu, 29 Apr 2021 12:01:56 -0400
From: Curtis Dutton
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] Best Mesa Thermistor Reading Combo
I'm upgrading the old spindle motor for my
On Sun, 25 Apr 2021, Ralph Stirling wrote:
Date: Sun, 25 Apr 2021 17:43:12 +
From: Ralph Stirling
Reply-To: "Enhanced Machine Controller (EMC)"
To: "emc-users@lists.sourceforge.net"
Subject: [Emc-users] Analog servo system
Getting back to my Realmeca C2 mill retrofit now.
I'm giving
On Fri, 23 Apr 2021, andrew beck wrote:
Date: Fri, 23 Apr 2021 16:23:35 +1200
From: andrew beck
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] wiring up mesa ency encoder
update on encoder splitting to altivar vfd and mesa
On Sun, 18 Apr 2021, Karl Jacobs wrote:
Date: Sun, 18 Apr 2021 19:02:47 +0200
From: Karl Jacobs
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] 7i92 hardware question
Hi all,
sorry if this has been asked before: I am planning on
On Sat, 17 Apr 2021, dave engvall wrote:
Date: Sat, 17 Apr 2021 08:14:34 -0700
From: dave engvall
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] 7i43 usage
Hi all,
I'm trying to use a 7i43 I've had on the shelf for awhile.
200K
On Wed, 14 Apr 2021, John Dammeyer wrote:
Date: Wed, 14 Apr 2021 22:27:08 -0700
From: John Dammeyer
Reply-To: "Enhanced Machine Controller (EMC)"
To: "'Enhanced Machine Controller (EMC)'"
Subject: Re: [Emc-users] Motion information.
From: Peter C. Wallace [mai
On Thu, 15 Apr 2021, andrew beck wrote:
Date: Thu, 15 Apr 2021 15:15:56 +1200
From: andrew beck
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] wiring up mesa ency encoder
Hey guys
looking for info on how to wire up a mesa ency
On Wed, 14 Apr 2021, John Dammeyer wrote:
Date: Wed, 14 Apr 2021 20:55:01 -0700
From: John Dammeyer
Reply-To: "Enhanced Machine Controller (EMC)"
To: "'Enhanced Machine Controller (EMC)'"
Subject: [Emc-users] Motion information.
I've returned to playing with the BeagleBone Black and
On Sun, 11 Apr 2021, andrew beck wrote:
Date: Sun, 11 Apr 2021 15:31:46 +1200
From: andrew beck
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] ethernet card not loading
hey everyone
I have a ethernet 7i82m card from mesa here
age-
From: Peter C. Wallace [mailto:p...@mesanet.com]
Sent: April-09-21 10:59 AM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Small PC for use with 7i90 / 7i96?
On Fri, 9 Apr 2021, John Dammeyer wrote:
Date: Fri, 9 Apr 2021 10:34:30 -0700
From: John Dammeyer < <mailto:
On Fri, 9 Apr 2021, John Dammeyer wrote:
Date: Fri, 9 Apr 2021 10:34:30 -0700
From: John Dammeyer
Reply-To: "Enhanced Machine Controller (EMC)"
To: "'Enhanced Machine Controller (EMC)'"
Subject: Re: [Emc-users] Small PC for use with 7i90 / 7i96?
From: andy pugh
arrot day, everybody! (Yes, it's really a thing)
Phil T.
The Feral Engineer
Check out my LinuxCNC tutorials, machine builds and other antics at
www.youtube.com/c/theferalengineer
On Sun, Apr 4, 2021, 11:59 AM Peter C. Wallace wrote:
On Sun, 4 Apr 2021, Dewey Garrett wrote:
Date: Sun, 4 Apr 2021
On Sun, 4 Apr 2021, Dewey Garrett wrote:
Date: Sun, 4 Apr 2021 15:36:30 - (UTC)
From: Dewey Garrett
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] [Emc-developers] Home_use_index issue revisited
The git *master* branch has
esetting the encoder position now but that's basically a no-op
since the encoder position is unused.
Phil T.
The Feral Engineer
Check out my LinuxCNC tutorials, machine builds and other antics at
www.youtube.com/c/theferalengineer
On Sun, Apr 4, 2021, 11:37 AM Peter C. Wallace wrote:
On Sun, 4 Apr
ition is not cleared. This means that linuxCNC will move
to a position determined by wherever the stepgen feedback happened
to be at index detection.
Phil T.
The Feral Engineer
Check out my LinuxCNC tutorials, machine builds and other antics at
www.youtube.com/c/theferalengineer
On Sun, Apr 4, 20
On Sun, 4 Apr 2021, Feral Engineer wrote:
Date: Sun, 4 Apr 2021 11:04:10 -0400
From: Feral Engineer
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] [Emc-developers] Home_use_index issue revisited
That's the thing, though.
On Sun, 4 Apr 2021, Feral Engineer wrote:
Date: Sun, 4 Apr 2021 10:04:29 -0400
From: Feral Engineer
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] [Emc-developers] Home_use_index issue revisited
But home should be
On Fri, 26 Mar 2021, Feral Engineer wrote:
Date: Fri, 26 Mar 2021 16:34:05 -0400
From: Feral Engineer
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] Heidenhain LS403 scale
Does anyone have a working solution for using
On Fri, 19 Mar 2021, Nicklas SB Karlsson wrote:
Date: Fri, 19 Mar 2021 19:07:50 +0100
From: Nicklas SB Karlsson
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] Spindle rps and index
Den 2021-03-19 kl. 10:53, skrev andy pugh:
On
InMTag & InMData1Pin,
IOPortTag & x"00" & InMTag & InMData2Pin,
Note that currently the minimum number of InM pins per module is 8
Take a look at PIN_7I96_inmD_51.vhd
From: Peter C. Wallace [p...@mesanet.com]
Sent: Monday, March 8, 2021 6:24 AM
To:
On Mon, 8 Mar 2021, Ralph Stirling wrote:
Date: Mon, 8 Mar 2021 05:07:15 +
From: Ralph Stirling
Reply-To: "Enhanced Machine Controller (EMC)"
To: "emc-users@lists.sourceforge.net"
Subject: [Emc-users] Muxed encoder counters vs regular encoder counters
I am making a custom
On Thu, 4 Mar 2021, John Dammeyer wrote:
Date: Thu, 4 Mar 2021 12:40:34 -0800
From: John Dammeyer
Reply-To: "Enhanced Machine Controller (EMC)"
To: "'Enhanced Machine Controller (EMC)'"
Subject: Re: [Emc-users] Following Error Joint 2
From: Les Newell [mailto:les.new...@fastmail.co.uk]
On Wed, 3 Mar 2021, John Dammeyer wrote:
Date: Wed, 3 Mar 2021 23:11:23 -0800
From: John Dammeyer
Reply-To: "Enhanced Machine Controller (EMC)"
To: "'Enhanced Machine Controller (EMC)'"
Subject: Re: [Emc-users] Following Error Joint 2
The comment on the link about Ethernet latency is
On Wed, 3 Mar 2021, John Dammeyer wrote:
Date: Wed, 3 Mar 2021 16:42:25 -0800
From: John Dammeyer
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] Following Error Joint 2
I made another video with the new 3D printed pulley.
The 7i90 is designed to be programmed from an epp parport, and I don't
believe it can be programmed again once an spi interface has been put in
it with out doing some jumper moving to reset it to parport drive before
it can be reprogrammed again. Its explained in the docs for it. It is
also
On Fri, 26 Feb 2021, Ralph Stirling wrote:
Date: Fri, 26 Feb 2021 19:26:58 +
From: Ralph Stirling
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] Rpi4 -> 7i90
You have to get an spi bitfile loaded before you can use spi.
On Fri, 26 Feb 2021, Ralph Stirling wrote:
Date: Fri, 26 Feb 2021 18:48:37 +
From: Ralph Stirling
Reply-To: "Enhanced Machine Controller (EMC)"
To: "emc-users@lists.sourceforge.net"
Subject: [Emc-users] rt data logging
I would like to do some realtime data logging
from hal to disk
On Tue, 23 Feb 2021, Alan Condit wrote:
Date: Tue, 23 Feb 2021 10:53:26 -0600
From: Alan Condit
To: "Emc-users@lists.sourceforge.net" ,
Wallace Peter C.
Subject: 7i76 spindle speed control with Cyclotrol C150 Controller
PCW,
I am trying to use my 7i76 Mesa card??s spindle control to
The 7I64 has low enough power draw that it can be powered via the CAT5 serial
cable
Manual says that it is for cable length less than 5 feet, which is
about 1,5 m. This machine will have cable length of 10+ m. I thought
that voltage drop would be too large.
Well, I guess that there is only
On Sun, 14 Feb 2021, Viesturs L?cis wrote:
Date: Sun, 14 Feb 2021 18:50:12 +0200
From: "[UTF-8] Viesturs L?cis"
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] Some questions about 6i25 and 7i77+7i74 combo
sv??td., 2021. g.
On Sun, 14 Feb 2021, Viesturs L?cis wrote:
Date: Sun, 14 Feb 2021 16:26:41 +0200
From: "[UTF-8] Viesturs L?cis"
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] Some questions about 6i25 and 7i77+7i74 combo
sv??td., 2021. g.
On Sat, 13 Feb 2021, Viesturs L?cis wrote:
Date: Sat, 13 Feb 2021 20:44:58 +0200
From: "[UTF-8] Viesturs L?cis"
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] Some questions about 6i25 and 7i77+7i74 combo
Hello!
I am trying to
On Mon, 25 Jan 2021, Ralph Stirling wrote:
Date: Mon, 25 Jan 2021 16:49:10 +
From: Ralph Stirling
Reply-To: "Enhanced Machine Controller (EMC)"
To: "emc-users@lists.sourceforge.net"
Subject: [Emc-users] hostmot2 bspi interface
So while I'm exploring hostmot2 communication
and while the pulse train
moves to the other trace, I get no more response.
-- Ralph
Well its neccesary for FPGA TX --> uC RX and uC TX --> FPGA RX
but clearly not sufficient. Are you sure the uC baud rate is correct?
____________
From: Peter C. Walla
On Wed, 20 Jan 2021, Ralph Stirling wrote:
Date: Wed, 20 Jan 2021 22:06:45 +
From: Ralph Stirling
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] Another Mesa vhdl question
I've got the STMBL code flashed on an
On Tue, 19 Jan 2021, Todd Zuercher wrote:
Date: Tue, 19 Jan 2021 20:50:49 +
From: Todd Zuercher
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] Spindle speed changes with threading.
I under stand the analogy, but I
On Tue, 19 Jan 2021, Gene Heskett wrote:
It wasn't the last time I tested it Jon, and most of the recent
conversations here are ignoreing the fact that every new stroke,
starting from its resting position, regardless of whether its a G76 or
you are "pecking" a G33.1 for rigid tapping, is a NEW
On Mon, 18 Jan 2021, Gene Heskett wrote:
Date: Mon, 18 Jan 2021 23:36:37 -0500
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] Spindle speed changes with threading.
On Monday 18 January 2021 22:21:
On Mon, 18 Jan 2021, Gene Heskett wrote:
But because once locked, its not a big deal if the cutting load slows the
spindle 25%, its still locked at that phase angle and it will stay that
way until the end of THAT cut stroke. But if YOU change the spindle
speed, then YOU have changed the synch
On Mon, 18 Jan 2021, John Dammeyer wrote:
Date: Mon, 18 Jan 2021 15:58:12 -0800
From: John Dammeyer
Reply-To: "Enhanced Machine Controller (EMC)"
To: "'Enhanced Machine Controller (EMC)'"
Subject: Re: [Emc-users] Spindle speed changes with threading.
On Mon, 18 Jan 2021, Ralph Stirling wrote:
Date: Mon, 18 Jan 2021 16:40:29 +
From: Ralph Stirling
Reply-To: "Enhanced Machine Controller (EMC)"
To: "emc-users@lists.sourceforge.net"
Subject: [Emc-users] Another Mesa vhdl question
The AD7740 v-to-f converters don't work as well
as
Does the state of the A input show up in hal?
that is, does hm2_7i90.0.encoder.00.input-a
reflect the status of the FPGA pin?
Peter Wallace
Mesa Electronics
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
oder A0,B0,Z0 pins with A0,A1,A2 pins to support up to three V-F converters.
Note that unconnected input pins will be terminated to a logic low level so the
unconnected 'B' input will be at a low level so the counting will be in the down
direction when in counter mode (and a negative velocity va
On Thu, 14 Jan 2021, Ralph Stirling wrote:
Date: Thu, 14 Jan 2021 17:40:51 +
From: Ralph Stirling
Reply-To: "Enhanced Machine Controller (EMC)"
To: "emc-users@lists.sourceforge.net"
Subject: [Emc-users] measuring frequency with 7i90
I am using an AD7740 voltage-to-frequency
foam cutters. I'm tired of
random castoff pc's.
Thanks again,
-- Ralph
____________
From: Peter C. Wallace [p...@mesanet.com]
Sent: Monday, January 11, 2021 4:34 PM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Rpi 3b+ to 7i90hd
CAUTION: This email
getting close to success?
Thanks again.
-- Ralph
____________
From: Peter C. Wallace [p...@mesanet.com]
Sent: Thursday, January 7, 2021 3:47 PM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Rpi 3b+ to 7i90hd
CAUTION: This email originated from outside the Wal
anks again.
-- Ralph
________
From: Peter C. Wallace [p...@mesanet.com]
Sent: Thursday, January 7, 2021 3:47 PM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Rpi 3b+ to 7i90hd
CAUTION: This email originated from outside the Walla Walla University email
system.
he 7c81, but not the 7i90hd.
The clock from the pi is correct.
Thanks again.
-- Ralph
____________
From: Peter C. Wallace [p...@mesanet.com]
Sent: Thursday, January 7, 2021 3:18 PM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Rpi 3b+ to 7i90hd
Looks r
On Thu, 7 Jan 2021, Ralph Stirling wrote:
Date: Thu, 7 Jan 2021 22:05:32 +
From: Ralph Stirling
Reply-To: "Enhanced Machine Controller (EMC)"
To: "emc-users@lists.sourceforge.net"
Subject: [Emc-users] Rpi 3b+ to 7i90hd
I have a Raspberry Pi 3b+ successfully talking to a
Mesa 7c81,
On Fri, 25 Dec 2020, Gene Heskett wrote:
Date: Fri, 25 Dec 2020 15:03:43 -0500
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: [Emc-users] for PCW
Greetings and Merry Christmas.
The 7i76 manual has mention of modes 0, 1, and
On Mon, 14 Dec 2020, Gene Heskett wrote:
Date: Mon, 14 Dec 2020 19:34:36 -0500
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: [Emc-users] calibrating the BS-1 battle
Greetings all, math whizes in particularly;
I couldn't
On Wed, 9 Dec 2020, Sven Wesley wrote:
Date: Wed, 9 Dec 2020 00:53:25 +0100
From: Sven Wesley
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] 7i96 multi wire input
Den ons 9 dec. 2020 kl 00:37 sk
On Wed, 9 Dec 2020, Sven Wesley wrote:
Date: Wed, 9 Dec 2020 00:17:11 +0100
From: Sven Wesley
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] 7i96 multi wire input
Friends,
I am in the process of refreshing a CNC that has been
On Mon, 7 Dec 2020, Gene Heskett wrote:
Date: Mon, 7 Dec 2020 17:07:58 -0500
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] [was Spindle indexing] now rigid tapping help
On Monday 07 December 2020 12:20:17 Jon
of
course would be limited by the servo thread rate.
Todd Zuercher
P. Graham Dunn Inc.
630 Henry Street
Dalton, Ohio 44618
Phone: (330)828-2105ext. 2031
-----Original Message-
From: Peter C. Wallace
Sent: Monday, December 07, 2020 1:08 PM
To: Enhanced Machine Controller (EMC)
Subje
On Mon, 7 Dec 2020, Todd Zuercher wrote:
Date: Mon, 7 Dec 2020 14:47:56 +
From: Todd Zuercher
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] Mesa Tacho Generator?
Is it possible to set up a firmware for a Mesa FPGA that
Advice needed! Was:
Plasma config with Telwin plasma source
Viesturs
pirmd., 2020. g. 30. nov., plkst. 22:57 ?? lietot??js Peter C. Wallace
() rakst??ja:
On Mon, 30 Nov 2020, Viesturs L?cis wrote:
> Date: Mon, 30 Nov 2020 22:35:21 +0200
> From: "[UTF-8] Viesturs L?cis"
On Tue, 1 Dec 2020, Todd Zuercher wrote:
Date: Tue, 1 Dec 2020 21:22:30 +
From: Todd Zuercher
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] Servo Amp Documentation?
Unfortunately the wiring is very simple in this
On Tue, 1 Dec 2020, Todd Zuercher wrote:
Date: Tue, 1 Dec 2020 17:22:25 +
From: Todd Zuercher
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] Servo Amp Documentation?
Anyone out there have any documentation for an older
On Mon, 30 Nov 2020, Gene Heskett wrote:
Date: Mon, 30 Nov 2020 17:07:04 -0500
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] crazy
Greetings all the pid experts;
I changed out the bob for one w/o the input
On Mon, 30 Nov 2020, Viesturs L?cis wrote:
Date: Mon, 30 Nov 2020 22:35:21 +0200
From: "[UTF-8] Viesturs L?cis"
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] Faulty THCAD board? 7i96 error? Advice needed! Was:
Plasma config
On Fri, 13 Nov 2020, Gene Heskett wrote:
Date: Fri, 13 Nov 2020 11:14:24 -0500
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: [Emc-users] back to a bad cable?
Greetings all;
I, despite seeingthe signals on the bobs input
Any ideas about those oscillations?
Viesturs
Can you post your hal/ini files?
Peter Wallace
Mesa Electronics
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
I would start over with a pncconf created configuration
On Mon, 9 Nov 2020, Viesturs L?cis wrote:
Date: Mon, 9 Nov 2020 00:00:55 +0200
From: "[UTF-8] Viesturs L?cis"
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] Velocity
On Sat, 7 Nov 2020, Gene Heskett wrote:
I think I've been doing that in my hal file(s) for at least a decade.
Based on if its got an index, why not use it? And if it doesn't have a
home switch, add one of those too.
Where would I see that error if there is a miss match?
Thanks Peter.
You
On Sat, 7 Nov 2020, andy pugh wrote:
Date: Sat, 7 Nov 2020 18:30:11 +
From: andy pugh
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] encoder vs headache and bad threads.
On Sat, 7 Nov 2020 at 18:03, Gene Heskett wrote:
On Fri, 6 Nov 2020, R C wrote:
Date: Fri, 6 Nov 2020 20:13:20 -0700
From: R C
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] quick question on parallel port cables
On 11/6/20 8:08 PM, andy pugh wrote:
On Sat, 7 Nov 2020 at
On Sat, 7 Nov 2020, andrew beck wrote:
Date: Sat, 7 Nov 2020 15:10:32 +1300
From: andrew beck
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] quick question on parallel port cables
hey everyone
I found that I am missing a
und and
analog lines to keep high frequency ground currents from the VFD out of
the servo system. (you could also use 470 ohm or series resistors
in ground and analog lines)
regards
Andrew
On Fri, Nov 6, 2020 at 12:05 PM Peter C. Wallace wrote:
On Fri, 6 Nov 2020, andrew beck wrote:
Date
erfect. I might use
a spare 7i76 now with the 7i77 and replace it once make my next order of
mesa cards
regards
Andrew
On Tue, Nov 3, 2020 at 4:42 AM Peter C. Wallace wrote:
On Mon, 2 Nov 2020, andrew beck wrote:
Date: Mon, 2 Nov 2020 22:31:32 +1300
From: andrew beck
Reply-To: "Enhance
On Mon, 2 Nov 2020, andrew beck wrote:
Date: Mon, 2 Nov 2020 22:31:32 +1300
From: andrew beck
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] how to control lathe spindle with a mesa 7i77 card
Thanks Jon.
I am controlling a
On Sun, 1 Nov 2020, dave engvall wrote:
Date: Sun, 1 Nov 2020 15:16:06 -0800
From: dave engvall
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] EPP
Middle of afternoon and I still need coffee. ;-) Let's try 7i43. Tnx.
The 7I43
On Thu, 22 Oct 2020, Gene Heskett wrote:
Date: Thu, 22 Oct 2020 04:41:19 -0400
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] Now do I have a bad card?
On Wednesday 21 October 2020 23:05:16 Peter
On Wed, 21 Oct 2020, Gene Heskett wrote:
Date: Wed, 21 Oct 2020 21:06:06 -0400
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] Now do I have a bad card?
On Wednesday 21 October 2020 20:21:30 Peter
On Wed, 21 Oct 2020, Gene Heskett wrote:
Date: Wed, 21 Oct 2020 19:45:56 -0400
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] Now do I have a bad card?
On Wednesday 21 October 2020 19:20:46 Peter
On Wed, 21 Oct 2020, Gene Heskett wrote:
Date: Wed, 21 Oct 2020 19:18:37 -0400
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] mesaflash problem, Peter plz comment
On Wednesday 21 October 2020 17:36:
On Wed, 21 Oct 2020, Gene Heskett wrote:
Date: Wed, 21 Oct 2020 18:55:40 -0400
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] Now do I have a bad card?
On Wednesday 21 October 2020 17:36:10 Peter
On Wed, 21 Oct 2020, Gene Heskett wrote:
Date: Wed, 21 Oct 2020 17:06:10 -0400
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] mesaflash problem, Peter plz comment
Greetings;
I have now written the
On Wed, 21 Oct 2020, Gene Heskett wrote:
Date: Wed, 21 Oct 2020 17:09:37 -0400
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] Now do I have a bad card?
On Wednesday 21 October 2020 16:15:40 Peter
On Wed, 21 Oct 2020, Gene Heskett wrote:
Date: Wed, 21 Oct 2020 16:08:37 -0400
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] Now do I have a bad card?
Greetings all;
I have re-written and reloaded the
On Fri, 16 Oct 2020, Gene Heskett wrote:
Date: Fri, 16 Oct 2020 15:49:17 -0400
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: "'Enhanced Machine Controller (EMC)'"
Subject: [Emc-users] For Peter
I went out to clear the input pins I'd need for the 2nd encoder I was
So, 2 questions for Peter CW: Can I run the 5i25's pwm-gens in different
modes? If so, how?
PWM modes are per channel so can be different on a per channel basis
Beware using bare FPGA I/O for driving HBridges that have non-isolated
inputs. These often have considerable ground bumping (in the
On Wed, 14 Oct 2020, andrew beck wrote:
Date: Wed, 14 Oct 2020 09:11:43 +1300
From: andrew beck
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] troubleshooting 6i25-7i77 mesa cards help please:)
Hey everyone
just having some
On Fri, 9 Oct 2020, Alan Condit wrote:
Date: Fri, 9 Oct 2020 16:42:47 -0500
From: Alan Condit
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Emc-users@lists.sourceforge.net"
Subject: Re: [Emc-users] Error on loading 5i25/7i76
Here is a link to my hal file
On Mon, 14 Sep 2020, Gene Heskett wrote:
Date: Mon, 14 Sep 2020 17:40:36 -0400
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] Setting up two home switches on Y
On Monday 14 September 2020 17:16:36 andy pugh
On Mon, 14 Sep 2020, Ed wrote:
Date: Mon, 14 Sep 2020 09:08:01 -0500
From: Ed
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] changing from 5i20 to 6i24
Well, my ancient computer that drives a lathe died and I no longer have any
On Sat, 12 Sep 2020, John Dammeyer wrote:
Date: Sat, 12 Sep 2020 19:13:43 -0700
From: John Dammeyer
Reply-To: "Enhanced Machine Controller (EMC)"
To: "'Enhanced Machine Controller (EMC)'"
Subject: Re: [Emc-users] Mini-PC
Mini USB cable arrived via Amazon today so I could power the HDMI
On Thu, 10 Sep 2020, Gene Heskett wrote:
Date: Thu, 10 Sep 2020 13:53:24 -0400
From: Gene Heskett
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] Q for Peter CW.
Greetings Peter;
How hard would it be to convert the
On Wed, 9 Sep 2020, andy pugh wrote:
Date: Wed, 9 Sep 2020 02:41:45 +0100
From: andy pugh
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] LinuxCNC 2.8.0 is released
On Wed, 9 Sep 2020 at 02:37, Gene Heskett wrote:
Andy,
On Fri, 4 Sep 2020, John Dammeyer wrote:
From what I understand, the MESA hardware essentially already offloads most of
the important real time stuff into the FPGAs. Remember, you can, in addition
to quadrature counters, PSI ports etc, fabricate an entire micro-processor
inside an FPGA.
On Wed, 2 Sep 2020, James Reed wrote:
Date: Wed, 2 Sep 2020 22:50:25 +
From: James Reed
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] 7i76 input with NPN NO
What am I missing here? I see a NPN output transistor as the
On Wed, 2 Sep 2020, Marius wrote:
Date: Wed, 2 Sep 2020 20:07:40 +0200
From: Marius
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: [Emc-users] 7i76 input with NPN NO
I am using a 7i76e which has sinking inputs. The machine was built using NPN
101 - 200 of 1866 matches
Mail list logo