changes during the
design process.
We use Orcad Capture for schematic entry and spice modeling. Protel for
layout.
Dave Eloranta
[EMAIL PROTECTED]
-Original Message-
From: Mira [mailto:[EMAIL PROTECTED]
Sent: Wednesday, July 14, 2004 9:58 PM
To: Protel EDA Forum
Subject: Re: [PEDA] SOT-23
Mr. Lomax
Bingo
You identified my problem. The pads are top Layer with a hole specified.
Does DXP have this fixed?
thank you
Dave Eloranta
[EMAIL PROTECTED]
5540 Research Park Dr.
Madison, WI
-Original Message-
From: Abd ul-Rahman Lomax [mailto:[EMAIL PROTECTED]]
Sent: Thursday
- Original Message -
From: Dave Eloranta <[EMAIL PROTECTED]>
To: 'Protel EDA Forum' <[EMAIL PROTECTED]>
Sent: Thursday, November 21, 2002 10:07 AM
Subject: [PEDA] shorted planes due to alignment pin holes with no plane
expansion
> Hi
> I just got a 10 layer board back wi
to regions of the board under BGAs that require a smaller plane
clearance of 12mils.
I am surprized that I have not run into this problem before.
Dave Eloranta
[EMAIL PROTECTED]
Locus Inc.
5540 Research Park Dr.
Madison, WI
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* To post a
use protel for all the board documents. If protel had
better dimensioning tools and mirroring control for plotting title blocks/borders
there would be no need for autocad for any of our board layouts.
Dave Eloranta
[EMAIL PROTECTED]
Locus Inc.
5540 Research Park Dr.
Madison, WI
-Original Me
Warning
Unable to process data:
multipart/mixed;boundary="=_NextPart_000_0003_01C28709.AAB8FA20"
rrect this file for future revisions.
Thank you
Dave Eloranta
Locus Inc.
5440 Research Park Dr.
Madison, WI
[EMAIL PROTECTED]
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* To post a message: mailto:proteledaforum@;techservinc.com
*
* To leave this list visit:
* http://www.techs
, there are vias galore.
Dave Eloranta
Locus Inc.
Madison, WI
-Original Message-
From: JaMi Smith [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, September 18, 2002 9:16 PM
To: Protel EDA Forum
Cc: JaMi Smith
Subject:[PEDA] Selective tenting on one side only
Hi All,
Can I
unchanged.
Thank you
Dave Eloranta
Locus Inc.
Madison WI.
* Tracking #: 9FD945AEC5C30247BFA3084C2E007D98764217AF
jumpers form during reflow.
Dave Eloranta
Locus Inc.
Madison, WI
-Original Message-
From: Emanuel Zimmermann [mailto:[EMAIL PROTECTED]]
Sent: Thursday, September 05, 2002 8:54 AM
To: Protel EDA Forum
Subject:Re: [PEDA] Solder jumper
Michael
I'm wondering if you ever
higher glass transition temperature. Our board house was able to suggest one
that they had used in the past.
Dave Eloranta
Locus Inc.
[EMAIL PROTECTED]
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On
Behalf Of Jon Elson
Sent: Wednesday, July 17, 2002 5:07 PM
To
I find that when the print preview is not working properly that I can get
the preview correct by highlighting the printer within the design explorer,
then editing the properties. Sometimes just touching the printer settings
then Process PCB.
Dave Eloranta
Locus Inc.
Madison, WI
[EMAIL PROTECTED
Igor
My use of the .designator string is because my locator drawing requires all
references visible and where possible within the component outline. The
silkscreen designator should whenever possible be outside the component
outline.
Dave Eloranta
Locus Inc.
Madison, WI
-Original Message
need make a new gerber, I then send a new
file name for that layer along with a new rev of the Fab Spec. . I find this
important so that boards are an absolute known element and the design can
move forward over time.
Dave Eloranta
Locus Inc.
Madison, WI
-Original Message-
From: [EMAIL PR
Tony
Here is what I wrote on this some time ago.
Thursday, August 09, 2001 8:08 PM
To: Protel EDA Forum
Subject:Re: [PEDA] reg clean ? Rotate components with drag tracks
Dave Eloranta wrote:
> Hi
> I was without the hole size editor for several months, then I lost x-y
> c
the proper position while Gcprevue showed it crossing other arcs. To fix it
I drew the arcs in metric units and the arcs appeared properly in both
Camtastic and GCPrevue. It would seem that Protel 9SE and Camtastic must
share some unit conversion code that has a bug.
Dave Eloranta
[EMAIL PROTECTED
ck with an independent
gerber viewer or translator.
Dave Eloranta
Locus Inc.
[EMAIL PROTECTED]
-Original Message-
From: Mike Reagan [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, October 31, 2001 6:58 AM
To: Protel EDA Forum
Subject:Re: [PEDA] DXF export bug?
> This may have b
Edi
I've used land patterns that look like two semi circles separated by 7-8
mils for test and debug shunts. These 2 pad footprints needed to be this
far apart so that it was easy to remove the bridge when required. They are
a little hard to manage because they are made of 2 pads 40mil round, 2
I have not been able to control arcs in a Clientbasic macro. Does anyone
have control over the start and end angles?
The use of Center method is the default but I've seen no example of method
specification. I guessed at this as in line 2. My arcs seem to start at a
quadrant and end at 3 oclock.
Yu-Ming Luo
You have identified a long time problem with Protel. I have my library
components constructed with a .designator string and an outline much as you
describe. Mine are on Mechanical 1, from days with only 4 mechanical layers.
My outlines are 4mil lines centered ten mils beyond the max pa
Hi
I was without the hole size editor for several months, then I lost x-y
coordinate display for library editing only. The only solution for me was to
completely uninstall all things Protel / client / pcb etc.. Then clean up
the registry getting all program references removed. And finally
reinstal
You might also watch for errors in the .LEGEND string if you use more than
sixteen drill sizes. This is more than a normal amount but the drill drawing
is a mess after sixteen sizes. It most often arises for me when SMD require
NPT holes. If a single drill tool could be used and a plating thickn
22 matches
Mail list logo
