I saw many attempts to call P97USI/P
And this single return today
240227_03153021.074 Rx FT8-18 0.3 838 JF2RDG RR73; JK1TCV
-14
Alan McDonald
Worimi Country
0413 657 427
From: Reino Talarmo via wsjt-devel
Sent: Tuesday, February 27, 2024 10:34 PM
To: 'WSJT software
Yes - Windows
Alan VK1AO
-Original Message-
From: jarmo via wsjt-devel
Sent: Wednesday, February 14, 2024 3:56 PM
To: wsjt-devel@lists.sourceforge.net
Cc: jarmo
Subject: Re: [wsjt-devel] Not sure if an issue
Wed, 14 Feb 2024 09:44:17 +1100
Alan McDonald via wsjt-devel
kirjoitti
to USB again.
Alan / VK1AO
From: David - K2DBK
Sent: Wednesday, February 14, 2024 8:25 AM
To: 'WSJT software development'
Cc: 'Alan McDonald'
Subject: RE: [wsjt-devel] Not sure if an issue
I've had this issue in the past (not currently happening) and switching
codecs has worked.
From
Instead of re-starting the application, have you tried just going to the
Audio tab, then de-selecting and then re-selecting the USB CODECS?
Alan
From: Marty Wayne via wsjt-devel
Sent: Wednesday, February 14, 2024 4:43 AM
To: WSJT software development
Cc: Marty Wayne
Subject: Re: [wsjt
you have the Wide Graph opened out? you will only decode what you see on
the wide graph yes?
Alan
On Tue, 5 Dec 2023 at 05:57, robert evans LAST_NAME via wsjt-devel <
wsjt-devel@lists.sourceforge.net> wrote:
> Using a IC-705 over the weekend and after
> installing the usb drivers in
We never want to remove all our skills from the operations - right?
Alan McDonald
Worimi Country
0413 657 427
-Original Message-
From: Reino Talarmo via wsjt-devel
Sent: Thursday, May 11, 2023 5:31 PM
To: 'WSJT software development'
Cc: Reino Talarmo
Subject: Re: [wsjt-devel] WSJTX
OK yes - point taken
Alan McDonald
-Original Message-
From: Reino Talarmo via wsjt-devel
Sent: Thursday, May 11, 2023 5:31 PM
To: 'WSJT software development'
Cc: Reino Talarmo
Subject: Re: [wsjt-devel] WSJTX Cabrillo log time
Well, it depends on the band and propagation mode
Well typically you can spend a long time calling (off and on) and then when
the counterparty responds it takes on 60 secs to complete.
As far as the counterparty is concerned, it never started until 60 sec prior
to complete.
Alan McDonald
Worimi Country
0413 657 427
-Original Message
I agree, big problem also for chasing rare DX that takes quite some time,
sometimes to complete.
I have to be diligent and make sure my log uses OFF and not ON because the
counterparty has OFF in their log.
I wish there was an option to leave checked = Use OFF time for ON/OFF
Alan McDonald
VK1AO
Why do you generate msgs if you are wanting to call CQ?
Generate Msgs takes the DXCall value but there is probably no value there if
you wish to call CQ.
Alan McDonald
VK1AO
-Original Message-
From: Glenn Williams via wsjt-devel
Sent: Tuesday, May 9, 2023 2:38 PM
To: wsjt-devel
I think I suggested something similar much earlier in the thread.
However with that new name rig and fake it don't mean anything so I'd
suggest change to hardware and software respectively.
Alan G0TLK, sent from my mobile device
On 8 May 2023 16:37:35 Adrian via wsjt-devel
wrote:
Sam
Since WSJT-X shifts any transmit audio below 1500Hz higher up the spectrum
how come we see RX signals on the waterfall below 1500Hz?
I presume on RX it shifts all signals back down by the same amount as they
were shifted up on TX?
Alan G0TLK, sent from my mobile device
On 8 May 2023 15:37:14
paragement -
it adds nothing to the discussion.
Alan McDonald
Worimi Country
0413 657 427
-Original Message-
From: Jim Brown via wsjt-devel
Sent: Tuesday, May 2, 2023 6:37 PM
To: Reino Talarmo via wsjt-devel
Cc: Jim Brown
Subject: Re: [wsjt-devel] Fwd: Enhancement suggestion - 30 sec
make sense?
In the context of WSJT-X it might be better to use something like "Hardware
AHS" and "Software AHS" with AHS meaning audio harmonic suppression rather
than split?
Alan G0TLK, sent from my mobile device
On 1 May 2023 12:18:59 Adrian via wsjt-devel
wrote:
that popup message I posted was from -Z. It too objects to running Fox in
std frequencies.
Alan
On Tue, 11 Apr 2023 at 00:34, jarmo via wsjt-devel <
wsjt-devel@lists.sourceforge.net> wrote:
> Mon, 10 Apr 2023 21:03:42 +1000
> Alan McDonald via wsjt-devel
> kirjoitti:
>
>
And for additional clarity - something many OP may not try. If you try to
switch to Fox mode on a std frequency, you will be met with this popup
[image: image.png]
You will not be able to TX in until you switch back to Normal mode or
change to a non-std frequency.
Alan
On Mon, 10 Apr 2023 at 20
.
T30UN QRZ page quote:
[image: image.png]
Alan
On Mon, 10 Apr 2023 at 20:27, 5p1kzx Michael via wsjt-devel <
wsjt-devel@lists.sourceforge.net> wrote:
> Hi Ton
>
> Those msg for different stations in a single stream and on the same time
> is mandatory for FT8DX Mode (WSJT-X
simultaneously.
Alan McDonald
VK1AO
From: Ton PA0TBR via wsjt-devel
Sent: Monday, April 10, 2023 6:28 PM
To: WSJT software development
Cc: Ton PA0TBR
Subject: Re: [wsjt-devel] F/H mode in wrong period
The messages had different reports for different stations in a single stream.,
my
I think you are assuming that they are using Fox and Hound with WSJT
flavours. They are more likely using MSHV which does not require odd/even
F/H.
They just look like they are F/H but are just multi stream. You can work
them as normal
Alan
On Sun, 9 Apr 2023 at 19:32, Ton PA0TBR via wsjt-devel
Hi, version 2.6.1-win64.exe from the new home page is triggering my AV
software, which then promptly deletes it.
My AV has never done this before on WSJT-X
Alan G0TLK, sent from my mobile device
___
wsjt-devel mailing list
wsjt-devel
worked when I did so from
Settings>Apps and Features
Maybe something like that is all that's necessary to clear this one up -
the installer to suggest a different default folder for each version?
Alan G0TLK
On 31/12/2022 13:46, Alan Groups via wsjt-devel wrote:
Following a system clea
ore version upgrading; or
* Incorporate minimum necessary system entry clean-up into the
installer script; or
* If an ability to run multiple versions on one machine is required
then amend the installer script so that it handles the system
entries to have each version remaining entirely separate
Hope th
stem
(not sure why it's doing that, further investigation to follow!)
Deleted all the entries in ProgramData and rebooted
Installed v 2.5.4, now all seems to be OK with just the single entry for
2.5.4 everywhere.
Alan G0TLK
On 28/12/2022 17:29, Alan Groups via wsjt-devel wrote:
Hi, in doing
an entry only for 2.5.2 so I'm
tempted to do a manual deletion of all these various entries, followed
by a reinstallation of 2.5.4?
--
Alan G0TLK
___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo
Control never failed.
Rx audio never stopped.
It was only Tx audio from USB Codec which flicked offline at random times.
This is no longer the case.
Alan McDonald
Worimi Country
From: Peter Sumner via wsjt-devel
Sent: Monday, 28 November 2022 4:38 PM
To: WSJT software development
Cc
s a rather long series of
changes and testing periods in all this. But it’s a nice feeling to have it
sorted.
Alan McDonald
Worimi Country
From: Black Michael via wsjt-devel
Sent: Wednesday, 23 November 2022 4:02 PM
To: Alan McDonald via wsjt-devel
Cc: Black Michael
Subject: Re: [wsjt
Yes this was done. Restarted. And no change for MY issue.
It’s an audio issue – not a USB issue IMO.
No issue with CAT control. WSJT-X always hears the radio, but the PC output to
the radio jumps away from the chosen output of WSJT-X and needs resetting
constantly.
Alan McDonald
Worimi
sounds being transmitted.
Alan G0TLK, sent from my mobile device
On 22 November 2022 23:44:29 Alan McDonald via wsjt-devel
wrote:
OK you have at least confirmed my observations.
Have you tried setting WSJT-X to NOT use the default device as per this:
But to use this setup (or similar)?
Alan
on the radio
scope. The sound is being re-directed from the NVIDIA/Monitors.
If I turn these to OFF
It stabilises. However, after reboot, the monitors grab control back again. I
can’t seem to make this OFF settings persistent.
Alan McDonald
Worimi Country
0413 657 427
From: Black
OK you have at least confirmed my observations.
Have you tried setting WSJT-X to NOT use the default device as per this:
But to use this setup (or similar)?
Alan McDonald
Worimi Country
0413 657 427
From: Peter Sumner via wsjt-devel
Sent: Wednesday, 23 November 2022
I'm not using a laptop with a battery. These settings, as you describe, are not
available on a mains power PC
Alan McDonald
Worimi Country
0413 657 427
-Original Message-
From: Glenn Williams via wsjt-devel
Sent: Wednesday, 23 November 2022 12:12 AM
To: wsjt-devel
tried moving my USB cable over to another port on the PC but this makes
no difference other than changin from say 2-USB to 3-USB etc.
Alan McDonald
Worimi Country
0413 657 427
From: Alan McDonald via wsjt-devel
Sent: Monday, 7 November 2022 9:43 AM
To: 'WSJT software development
So I’ve been running WSJT-X for the last few days chasing the DXpedtions. I’m
setup with IC-7300 and comport6 instead of the HamRadioDeluxe radio and
server:port settings.
I have not had even one hint of an issue in 3 days.
Alan McDonald
Worimi Country
0413 657 427
From: Alan McDonald
It’s more likely to be that extra layer involved.
WSJT-X is using the HRD Radio, and the HRD Radio is talking to the HRD Rig
Control app which is talking down the Com port.
That extra layer has me suspicious.
I might reset all the baud rates involved.
Alan McDonald
Worimi Country
0413
know the smell of a software
issue.
There’s a section of latency in the setup which flicks a setting in the radio
or triggers an incorrect CAT instruction.
Alan McDonald
Worimi Country
0413 657 427
From: Black Michael
Sent: Saturday, 5 November 2022 2:46 PM
To: wsjt-devel
t does not come back. So
I have to do it again.
Occasionally this little technique fails to bring back Tx. I need to exit and
re-start WSJT-X and Tx returns to normal again for a while, until the next fail.
Alan McDonald
Worimi Country
0413 657 427
From: Black Michael mailto:mdblac...@yah
I can supply some screen shots of my radio.
I have a third behaviour. My trick of tripping Halt and Enable also
sometimes fails to bring the audio back. Tx still occurs but no audio is
passing.
If I exit WSJT-X and restart it, audio returns to the Tx.
Alan McDonald
VK2MET
From: Alan
direct via com port 6 I never have the issue. But that means
exiting HRD rig control each time and I certainly like opening WSJT-X with
one click rather than the scramble required to disconnect and reconnect etc.
Plus the logging and multi-casting is important to me as well to use
GridTracker.
Alan
From memory my crashing was on 2.5.4, couldn't see any particular reason.
Haven't been able to use the RC in depth yet, too many other demands on my
time!
Alan G0TLK, sent from my mobile device
On 25 October 2022 14:51:53 Dennis W1UE via wsjt-devel
wrote:
GM Joe
Summation of Yesterdays
of globally trapping fatal errors such that the program
exits more gracefully?
The latter might also assist in finding the fault?
If not directly then maybe run it in its own container so if that sees a
fatal error in its content it can close nicely?
Alan G0TLK, sent from my mobile device
On 24
over a much longer time
period or come up with another faster way to generate a TX FSK frequency. Hence
bypassing the D>A in WSJT and A>D in the microprocessor.
73,
Alan
AG7XS
> On Sep 19, 2022, at 11:15 AM, William Smith via wsjt-devel
> wrote:
>
> The http://qrp-labs.com/qd
of WSJT-X and
then adding the result to the base frequency in an SI5351. The SI5351 is sent a
digital number which is the sum of the FSK offset and the base frequency. Would
it be possible to sent the FSK frequency with greater resolution so that it
approximated a continuous FSK signal?
73,
Alan
. We have been using VOX or CAT control for PTT, but could update that to
CAT only.
In addition if USB CAT polling interval requests could be blocked during TX
periods, that would be even great as it prevent dropouts and data conflicts if
using a USB hub with audio dongle.
73,
Alan
AG7XS
Might it be the HDD/SSD going to sleep?
I've got other software that can mess about as a result of that.
Look in settings, power and maybe also then click on advanced or further
settings.
Alan G0TLK, sent from my mobile device
On 9 September 2022 14:39:40 Carl Moreschi via wsjt-devel
wrote
Hi, Omnirig software should be able to do this for you.
Alan G0TLK, sent from my mobile device
On 24 August 2022 00:30:03 Pino Zollo via wsjt-devel
wrote:
This does not control one of the two radios...for instance the frequency
change.
I use the virtual audio channel to control the RTL
I had this begin to happen on a previously stable version 2.5.3 but a long
delayed upgrade to 2.5.4 got rid of it, W10. Only a week or so ago.
I haven't been able to test the RC yet, but thought I'd report this just in
case it's from the same cause.
Alan G0TLK, sent from my mobile device
Hi,
I have 2 suggestions:
1. When there are a large number of users on any one band the Band Activity
screen overflows and you are looking for a particular station to work it often
takes too long to find the call in the list thereby missing out on calling it.
My suggestion is that a marker
might be good?
Alan G0TLK, sent from my mobile device
On 6 March 2022 09:31:50 Charles Suckling via wsjt-devel
wrote:
Gavin, Tony et al
I personally find it useful to be able to generate a continuous carrier
with WSJT-X using the Tune button.
73
Charlie DL3WDG
On Sun, 6 Mar 2022 at 10:13
before.
W10 Pro 64 bit
--
Alan G0TLK
___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
Shocking and saddening news, he will be greatly missed.
My condolences to his family and friends, and RIP Bill.
Alan G0TLK, sent from my mobile device
On 4 December 2021 21:25:09 Joe Taylor via wsjt-devel
wrote:
I am very sorry to convey the sad news that Bill Somerville, G4WJS, died
.
May or may not help!
Alan G0TLK, sent from my mobile device
On 12 November 2021 16:11:51 Saku via wsjt-devel
wrote:
Black Michael kirjoitti 12.11.2021 klo 15.54:
Try a new config and see if that fixes the problem.
wsjtx -r test
Mike W9MDB
Hi Mike!
No help. It is what it is and has
your rig with WSJT.
Don't forget rig has to be switched on, and it's nothing to do with the
Kenwood driver.
Alan G0TLK, sent from my mobile device
On 14 October 2021 19:35:04 Enrico OE1EQW via wsjt-devel
wrote:
The driver for the virtual serial port has been downloaded from a Kenwood site
Hi, while that may work it's in my view better to find the source of any
RFI and get rid of it.
You never know what else it might be doing!
Try the setup on a dummy load and if it's then OK look at the
antenna/feeder arrangement.
Alan G0TLK, sent from my mobile device
On 24 September 2021
Would the WSPR protocol work better than the FT8 protocol in such a system?
Alan G0TLK, sent from my mobile device
On 23 September 2021 19:19:53 Glenn M-H via wsjt-devel
wrote:
Maybe a sound processing system can analyze the sound signal and place the
FT8 signal between the lowest human
become
critically important?
Maybe a special RC version could optionally upload sufficient data for
offline collision analysis?
Alan G0TLK, sent from my mobile device
On 2 September 2021 19:19:12 Phil Karn via wsjt-devel
wrote:
On 9/2/21 2:26 AM, alan2--- via wsjt-devel wrote:
Hi, I've
Hi Mike,
I wonder if the retry count could be reset after a successful connection.
73 Alan M0NNB
On Mon, Jul 12, 2021 at 5:06 PM Alan Hopper
wrote:
> Hi Mike,
> this is with WSJT-X connecting to the fake rigctld in SparkSDR. It
> connects and then if a delay happens some time lat
connections it would be nice if it kept reconnecting.
73 Alan M0NNB
On Mon, Jul 12, 2021 at 4:45 PM Black Michael via wsjt-devel <
wsjt-devel@lists.sourceforge.net> wrote:
> It should be trying to reconnect twice with 3 second timeout each time.
>
> What rig are you using? You
on heavily loaded pcs running many WSJT-X instances 24/7. The
delays happen in a low level socket send so I don't think I have any
control over it.
I see it in 2.4.0 and 2.5.0rc3, I've not tested with any other versions.
Is this intended behaviour or a bug?
73
Will it be the VID or PID data?
Alan G0TLK, sent from my mobile device
On 22 June 2021 18:14:52 William Smith wrote:
In my WSJT-X.ini file, I've got:
SoundInName=IC-7100_Rx (3- USB Audio CODEC )
SoundOutName=IC-7100_TX (3- USB Audio CODEC )
I can't see anything changing with that device
That also works for me.
Alan G0TLK, sent from my mobile device
On 16 June 2021 23:40:03 Jon Anhold wrote:
I would say that what WSJT-X refers to as "Configurations" are commonly
called "Profiles".
73 de KM8V
On Wed, Jun 16, 2021 at 12:12 PM Bill Somerville wrote:
Hi
Thanks for the explanation, looks good to me!
Alan G0TLK, sent from my mobile device
On 11 June 2021 02:01:42 Bill Somerville wrote:
On 09/06/2021 00:38, Bill Somerville wrote:
Hi all WSJT-X users,
we are looking into some performance enhancements that will take
advantage of some parallel
, at least until non
AVX machines aren't commonly viable in hobby use.
Alan G0TLK
On 10 June 2021 21:16:03 Jim Brown wrote:
On 6/10/2021 2:02 AM, Alan wrote:
I agree up to a point, but this is a hobby and older kit is often in
service for long periods to keep financial cost down.
It's
to test for the extensions and set a flag accordingly. New code or maybe
new modes that must use AVX could then simply check the flag and pop up a
box to say CPU upgrade needed?
Anyway, getting off topic.
Alan G0TLK, sent from my mobile device
On 9 June 2021 23:13:23 Jeff Stillinger via wsjt
will know how it performs under such loads.
Thermal cycling is another consideration, again duty cycle dependent.
My query is therefore how the load increase occurs, in particular the
length of time it lasts and how frequent it will be. Hopefully no problem
but just some things to check.
Alan G0TLK
?
Alan G0TLK, sent from my mobile device
On 9 June 2021 19:07:06 Bill Somerville wrote:
On 09/06/2021 18:22, Black Michael via wsjt-devel wrote:
Is there some reasons to think we get a notable performance boost from AVX?
First link I found is not impressivevery few benchmarks show much
Indeed one cannot be certain, but the further exchange increases the
probability of the QSO being complete for both parties.
Alan G0TLK, sent from my mobile device
On 7 May 2021 18:30:43 Bill Frantz wrote:
On 5/7/21 at 2:54 AM, al...@alangroups.plus.com (Alan) wrote:
The final 73
as anything else.
Alan G0TLK, sent from my mobile device
On 6 May 2021 23:59:23 David Gillooly wrote:
Some hams on there end will not log a QSO unless they receive the
confirmation 73 after their RRR/RR73.
I am not saying its wrong or right just that it's the practice of some hams
Dave, AA6RE
On Thu
Hi Joe,
thanks, I'll remove them then. That will make monitoring all at once more
doable.
73 Alan M0NNB
On Mon, Apr 19, 2021 at 9:04 PM Joe Taylor wrote:
> Look at the current Guide. FST4 and FST4W have no submodes with larger
> tone spacings.
>
> On 4/19/2021 3:41 PM, Alan
Hi Reino,
thanks but nope, I mean the submodes that have larger tone spacings, A
standard, B x 2, C x 4, D x 8, that were mentioned in one of the quick
start guides.
73 Alan M0NNB
On Mon, Apr 19, 2021 at 8:34 PM Reino Talarmo
wrote:
> Hi Alan,
>
> Do you mean by a submode differen
Hi,
I'm just tweaking the FST4 support in SparkSDR and had added support for
the A,B,C submodes but they do not seem to be an option in the latest
WSJTX, have I missed a setting or should I remove those options?
73 Alan M0NNB
___
wsjt-devel mailing list
. This was
Windows XP at the time as I recall.
Perhaps with later versions of Windows (10 etc.), the Virtual Memory system has
changed.
So, can you check the program's memory usage, both real and virtual?
At the time I had to convince the developer, Virtual Memory is not limitless.
Alan VK2ZIW
#2 0x
#3 0x
#4 0x
#5 0x
#6 0x
#7 0x
#8 0x
#9 0x
#10 0x
#11 0x
#12 0x
#13 0x
#14 0x
73 Alan M0NNB
On Tue, Jan 26, 2021 at 3:45 PM Alan Hopper
wrote:
> Hi Bill,
> thanks for the repl
, booting/waking the laptop and/or the USB
ports used for each device.
It's not a serious issue and therefore not something I'll spend a lot of
time hunting down, nor stop using the GPS dongle as a result.
Alan G0TLK, sent from my mobile device
On 4 March 2021 21:04:08 Mark Spencer wrote:
I
.
Whether a nudge button would be useful or work for me I don't know, because
from experience my clock drift is quite dynamic and unpredictable, but
great to see new constructive ideas being presented.
Alan G0TLK, sent from my mobile device
On 4 March 2021 16:46:19 Jim Pennino via wsjt-devel
If it's a site near the car or maybe in a building etc, then yes the dongle
works well.
However if on foot while certainly not a major issue it's one more thing to
pack/carry, and to go wrong, plus of course it uses more of the scarce
battery power.
Alan G0TLK, sent from my mobile device
that was done only
inside WSJT-X and only for the current session - no changes to the system
clock itself, or permanent config changes.
Alan G0TLK
On 4 March 2021 07:31:47 Claude Frantz wrote:
On 3/4/21 1:53 AM, David Smith wrote:
Proposal:
Add an adjustment that allows you to manually
Maybe use a completely different app on the same system and then see if
the distortion is still there?
Alan G0TLK
On 17/02/2021 13:02, Black Michael via wsjt-devel wrote:
Since I've also verified this on an IC-7300 with it's own USB sound
card seems it's a Windows bug. I think
by hopefully reducing support requests, by enabling users to more
easily find stuff out for themselves. Keep up the good work.
Alan G0TLK
On 16/02/2021 11:16, Bill Somerville wrote:
Alan,
that is a completely unreasonable request, WSJT-X uses many supporting
libraries and on some platforms
leads to unnecessary bug reports and
frustration/irritation all round!
Alan G0TLK
On 16/02/2021 10:49, tom wrote:
Thanks for the update Bill
I have no issue with options being configurable but as Alex put it -
’never touch a running system’ - tidy up coding to make it more robust
yes
Haven't tested this version yet but something else that might be good in
my view is to have a CAT command to vary maximum power output available
from the rig, for those rigs that support it?
Alan G0TLK
On 15/02/2021 14:35, Rich - K1HTV wrote:
I noticed that while running WSJT-X v2.4.0-rc1
Hi, use the colour highlighting settings? There are options in there for
grids not already in the log, and also grids not in the log by band.
Alan G0TLK
On 14/02/2021 16:48, jeff millar wrote:
Hello all,
Sometimes I need to search the Band Activity list for a specific
station who is known
Hi Bill,
thanks for the extra info, I noticed the padding as I added extra padding
to the nearest 32 bits as I do the parity generation in 32 bit chunks.
73 Alan M0NNB
On Wed, Feb 10, 2021 at 3:49 PM Bill Somerville
wrote:
> On 10/02/2021 15:06, Bill Somerville wrote:
>
> On 10/02/2
in
the rest:)
73 Alan M0NNB
On Wed, Feb 10, 2021 at 3:09 PM Bill Somerville
wrote:
> On 10/02/2021 14:40, Alan Hopper wrote:
> > Hi,
> > I'm trying to write a FST4 encoder without using the source, I'm most
> > of the way there using the excellent FT4_FT8_QEX and FST4
the
source without breaching the licence? Also what BT is used for the
Gaussian shaping. I see details of the 50 bit payload are 'in preparation',
If you want a proofreader, I'll very happily proof read by trying to
implement it:)
Thanks again for the great documentation and modes.
73 Alan M0NNB
regardless of what rig ratings might
be. The Tx output will also usually be a bit more linear and therefore
cleaner.
Alan G0TLK
On 04/02/2021 08:47, Saku wrote:
Hi!
If your rig has FM and has full output power there without warnings of
FM TX period lengths the PA should handle it.
FM, or CW
Hi, this adjustment is part of W10 (assuming you have latest version) -
Settings>System>Sound>Advanced sound options>App volume device preferences
Hope that assists.
Alan G0TLK
On 01/02/2021 09:10, Maurizio Brameri wrote:
Hi everyone,
is there a way to set automatically at lau
he code obviously read the message while I was in the middle of typing JA!
Incidentally while I was being received in JA no QSO resulted from the
above messing about - band opening closed!
Hope that helps.
Alan G0TLK
___
wsjt-devel mailing lis
Hi Bill,
thanks for the reply, I just tried jt9 -w 1 -m 1 -6 -9 -p 1 -d 3 -L 100 -H
4000 210125_1758.wav and I'm afraid no decodes, checked same cmd on an old
version and that still worked.
73 Alan M0NNB
On Tue, Jan 26, 2021 at 3:27 PM Bill Somerville
wrote:
> On 26/01/2021 14:16, Alan Hop
Hi,
I don't seem to be getting any JT9 or JT65 decodes when using jt9.exe
directly. The cmd I use is jt9 -w 1 -m 1 -6 -9 -p 1 -d 3 210125_1758.wav
which works with earlier versions. It now simply returns
0 0. with no errors.
Other modes seem fine. Has the command line changed?
73 Alan M0NNB
Thanks!
Alan G0TLK, sent from my mobile device
On 7 January 2021 22:42:59 Bill Somerville wrote:
Alan,
as I said to Uwe, he should remove the logging configuration file I gave
him to temporarily diagnose an issue. The default logging is not verbose at
all and absolutely trivial compared
to something more significant.
Are there any others?
If so could there perhaps be a diagnostic mode where such files get
written, but otherwise they don't? Would also cut resource use, always a
good thing in my view, even if relatively minimal.
Alan G0TLK, sent from my mobile device
On 7 January
it goes...
Bill has said the facility to enable this suggestion to happen is
already present, so if there's sufficient demand no doubt someone will
pick it up?
Alan G0TLK
On 05/12/2020 15:37, Dave Slotter, W3DJS wrote:
Hi Bill,
Thank you for such a detailed and thoughtful response
It occurs to me that this may also need to be checked the EU General
Data Protection Regulation (GDPR)? It's very wide in effect!
Alan G0TLK
On 03/12/2020 16:32, Bill Frantz wrote:
Given the number of cultural differences in naming, it is a difficult
question which name is the given name
Got on with something else, and on another try RC02 is now decoding again.
Alan G0TLK
On 29/11/2020 17:24, Alan Groups wrote:
And now RC2 won't decode anything, 2.2.2 is fine!
Alan G0TLK
On 29/11/2020 17:21, Alan Groups wrote:
Hi, running 2.3.0 RC2, Kenwood TS590S:
* Double click
And now RC2 won't decode anything, 2.2.2 is fine!
Alan G0TLK
On 29/11/2020 17:21, Alan Groups wrote:
Hi, running 2.3.0 RC2, Kenwood TS590S:
* Double click a station to call it
* Rig goes into Tx
* Click halt TX
* RC2 brings up a rig control error asking me if I wish to reconfigure
folder) - transmit simply stops
Alan G0TLK
___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
This article also gives a full explanation - updated in 2019.
https://techcommunity.microsoft.com/t5/ask-the-performance-team/the-basics-of-page-faults/ba-p/373120
Alan G0TLK
On 20/10/2020 15:23, Black Michael via wsjt-devel wrote:
Hmmm...not what this says...they claim a hard fault is asking
TS590S
Alan G0TLK, sent from my mobile device
On 20 October 2020 13:37:24 Bill Somerville wrote:
Hi Alan,
same question for you, what is your Rx please?
73
Bill
G4WJS.
On 20/10/2020 13:20, Alan Groups wrote:
Hi, just tested 2.3.0 RC1 for this:
Running Meinberg NTP, time.is reporting exact
myself now!
Alan G0TLK
On 20/10/2020 12:54, Bill Somerville wrote:
On 09/10/2020 20:51, Bobby Chandler wrote:
Has anyone noticed the DT being off by .3 to .4 on FT8 on the
2.2.0-rc1 version, even when time.is shows exact? It is OK on FT4 and
V2.2.2, always within about .1. Seems maybe a delay
it up
to find out.
Alan G0TLK, sent from my mobile device
On 4 October 2020 14:52:34 Bill Somerville wrote:
On 04/10/2020 11:23, Alan Groups wrote:
One other thing - would be more intuitive if one could delete a
configuration without having to open another one first!
Alan G0TLK
Hi Alan
1 - 100 of 211 matches
Mail list logo
