Re: [WISPA] MT power supplies THE SOLUTION
Regarding cable That makes since. We really like the Arc wireless cable because it meets the need for 70% of the CPE side installs (residential and small business) with ease of use and the right price. The industry really needed a product like that. But the ARC cable is what it is, and is no substitution for high grade cable when it is needed. The Superior Essex we use now, has been proven to be awesome. We use it the other 25% of the time, when we have long runs or have to extend across gravel flat roof (where there is risk it will be submerged in water or walked on.). Many don't realize that it is not just the metal shielding that gives isolation from interference (environmental or self induced crosstalk). The non-metalic outer jacket and inner jacket of the wires also have isolating characteristics that contribute. There is something to be said for total thickness of a cable. Tom DeReggi RapidDSL & Wireless, Inc IntAirNet- Fixed Wireless Broadband - Original Message - From: "Brian Rohrbacher" <[EMAIL PROTECTED]> To: "WISPA General List" Sent: Friday, September 15, 2006 10:33 PM Subject: Re: [WISPA] MT power supplies THE SOLUTION Good points. Likely I will not touch it again unless it breaks. I'll try to get a make on the "good" cable, but I know the cheap stuff I ran yesterday is the arc wireless shielded, flooded, drainwire, I picked up 6 months ago when it was $69 a roll. Brian Tom DeReggi wrote: So the question that arises, is why did that fix it? I see two possibilities 1) Poor quality cable or cable shields. (Loss running Ethernet data parallel to power) 2) Sharing a CAT5 jack on the 532 main board for Power and Data. Travis previously talked about the horrid RF interferrence that the 532 board generated when using 48V, due to the 532 onboard power converter/supply. I'm wondering if the distortion/loss was at the board itself apposed to cable? It would have been interesting to know, if you used one cable for both data and power, but terminated the data pairs to a different Ethernet port instead of the POE port used for power. What also would have been interesting would have been to know wether a 18V power supply would have worked on a shared single cable. Different ethernet chipsets do have different characteristics and ranges. So it is possible that just the different chip made the difference based on compatibilty or characteristics of chip. But the other reasons are just as probable. What brand (not just shield type) cable were you using? I realize that you would not likely pursue additional tests as you found a fix already, but it would be interesting to know, just so we can keep collecting data should we experience similar problems in the future. We had a similar situation that was due to chipset. We ran 10 mbps ethernet 550 feet to our subscriber. (different radio brand). We used a slightly higher power voltage to make up for cable loss. Our laptops worked great over the link. The customer's 3 identical routers could not stay connected for long. We were not sure if it was a speed autodetection issue, or the distance for the chip to work. We installed a 10mbps Cisco Switch in between their router and our cable dmarc in their premise, and it all worked. Tom DeReggi RapidDSL & Wireless, Inc IntAirNet- Fixed Wireless Broadband - Original Message - From: "Brian Rohrbacher" <[EMAIL PROTECTED]> To: "WISPA General List" Sent: Friday, September 15, 2006 9:20 AM Subject: Re: [WISPA] MT power supplies THE SOLUTION I started with RB 532 on tower. It comes down 265 feet to poe injector to router. Major packet loss. 2) switched RB 532 out. No change. 3) Created test setup on ground with "bad board" and it looked fine. (from laptop--6ft cablepoe265 ft---RB) 4) Blamed it on the cable, and got a cable certifier from a friend. 5) Right before climb, I re did the test setup on the ground. This time I plugged the 265 feet into the actual router instead of my laptop. The problen was back. (I was bummed) 6) One final test. Get another 265 foot cable. I used 265ft for power and 265ft for data to eth 2 or 3. Problem solved. I can only speculate that the chipset on RB 532 poe port is diffrent from the chipset on eth 2/3. And for whatever reason it was not compatable with cable, hardware, ect.setup. I may never know for sure why, but I have the workaround. Good enough for me. FWIW I ended up pulling 2 new cables (all 3 certified fine). I used the original cable for data (it has "real" shield) I used my new 2 (cheapo foil shield) for power and slapped the other into eth3 for the heck of it. Lessons learned for next time. Measure cable, crimp, and power up on ground using the EXACT same everything as what the final deployment will have. And then test
Re: [WISPA] MT power supplies THE SOLUTION
Couldn't find it. Under cable settings is default, standard, and short. From the manual it looks like default = "long cable" and it looks like default is the default. But I have no idea how to see what mode it is on. Brian Rick Smith wrote: Brian, did you try the "long cable" setting on that particular interface ? Brian Rohrbacher wrote: I started with RB 532 on tower. It comes down 265 feet to poe injector to router. Major packet loss. 2) switched RB 532 out. No change. 3) Created test setup on ground with "bad board" and it looked fine. (from laptop--6ft cablepoe265 ft---RB) 4) Blamed it on the cable, and got a cable certifier from a friend. 5) Right before climb, I re did the test setup on the ground. This time I plugged the 265 feet into the actual router instead of my laptop. The problen was back. (I was bummed) 6) One final test. Get another 265 foot cable. I used 265ft for power and 265ft for data to eth 2 or 3. Problem solved. I can only speculate that the chipset on RB 532 poe port is diffrent from the chipset on eth 2/3. And for whatever reason it was not compatable with cable, hardware, ect.setup. I may never know for sure why, but I have the workaround. Good enough for me. FWIW I ended up pulling 2 new cables (all 3 certified fine). I used the original cable for data (it has "real" shield) I used my new 2 (cheapo foil shield) for power and slapped the other into eth3 for the heck of it. Lessons learned for next time. Measure cable, crimp, and power up on ground using the EXACT same everything as what the final deployment will have. And then test. Hope that sums it all up. Ok to directly answer your question. Yes. I did this on the ground test unit. Brian Rohrbacher Paul Hendry wrote: Brian, Just out of interest, did you try running both power and data over the new cable and did you still see the same issue? P. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: 15 September 2006 02:43 To: WISPA General List Subject: Re: [WISPA] MT power supplies THE SOLUTION First off. I'm back to a 48v 420mA power supply. To the solution. I ran another cat5 up the tower and plugged it into the RB 532. Now I have one cable for poe and one cable for data, and it all works fine. And check this. My headache went away as soon as the problem did. :) Problem solved. NEXT! Brian Tom DeReggi wrote: Amps don't mean a thing without disclosing Volts, Consider Watts instead. 1300mA at 3V is much different than 1300mA at 18V. The mPCI slot (SR5) is 3.3V. Power to the Motherboard is from 12-48V. W=V*A Tom DeReggi RapidDSL & Wireless, Inc IntAirNet- Fixed Wireless Broadband - Original Message - From: "Mark McElvy" <[EMAIL PROTECTED]> To: "WISPA General List" Sent: Wednesday, September 13, 2006 8:19 AM Subject: RE: [WISPA] MT power supplies I am surprised no one has mentioned this. I looked up power consumption on the SR5 and it shows 800 to 1300 mA each. You state your power supply is 700mA. I did not look up power consumption for the RB532 but I would think you would need at least a 3A supply. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 11:51 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies THE SOLUTION
Good points. Likely I will not touch it again unless it breaks. I'll try to get a make on the "good" cable, but I know the cheap stuff I ran yesterday is the arc wireless shielded, flooded, drainwire, I picked up 6 months ago when it was $69 a roll. Brian Tom DeReggi wrote: So the question that arises, is why did that fix it? I see two possibilities 1) Poor quality cable or cable shields. (Loss running Ethernet data parallel to power) 2) Sharing a CAT5 jack on the 532 main board for Power and Data. Travis previously talked about the horrid RF interferrence that the 532 board generated when using 48V, due to the 532 onboard power converter/supply. I'm wondering if the distortion/loss was at the board itself apposed to cable? It would have been interesting to know, if you used one cable for both data and power, but terminated the data pairs to a different Ethernet port instead of the POE port used for power. What also would have been interesting would have been to know wether a 18V power supply would have worked on a shared single cable. Different ethernet chipsets do have different characteristics and ranges. So it is possible that just the different chip made the difference based on compatibilty or characteristics of chip. But the other reasons are just as probable. What brand (not just shield type) cable were you using? I realize that you would not likely pursue additional tests as you found a fix already, but it would be interesting to know, just so we can keep collecting data should we experience similar problems in the future. We had a similar situation that was due to chipset. We ran 10 mbps ethernet 550 feet to our subscriber. (different radio brand). We used a slightly higher power voltage to make up for cable loss. Our laptops worked great over the link. The customer's 3 identical routers could not stay connected for long. We were not sure if it was a speed autodetection issue, or the distance for the chip to work. We installed a 10mbps Cisco Switch in between their router and our cable dmarc in their premise, and it all worked. Tom DeReggi RapidDSL & Wireless, Inc IntAirNet- Fixed Wireless Broadband - Original Message - From: "Brian Rohrbacher" <[EMAIL PROTECTED]> To: "WISPA General List" Sent: Friday, September 15, 2006 9:20 AM Subject: Re: [WISPA] MT power supplies THE SOLUTION I started with RB 532 on tower. It comes down 265 feet to poe injector to router. Major packet loss. 2) switched RB 532 out. No change. 3) Created test setup on ground with "bad board" and it looked fine. (from laptop--6ft cablepoe265 ft---RB) 4) Blamed it on the cable, and got a cable certifier from a friend. 5) Right before climb, I re did the test setup on the ground. This time I plugged the 265 feet into the actual router instead of my laptop. The problen was back. (I was bummed) 6) One final test. Get another 265 foot cable. I used 265ft for power and 265ft for data to eth 2 or 3. Problem solved. I can only speculate that the chipset on RB 532 poe port is diffrent from the chipset on eth 2/3. And for whatever reason it was not compatable with cable, hardware, ect.setup. I may never know for sure why, but I have the workaround. Good enough for me. FWIW I ended up pulling 2 new cables (all 3 certified fine). I used the original cable for data (it has "real" shield) I used my new 2 (cheapo foil shield) for power and slapped the other into eth3 for the heck of it. Lessons learned for next time. Measure cable, crimp, and power up on ground using the EXACT same everything as what the final deployment will have. And then test. Hope that sums it all up. Ok to directly answer your question. Yes. I did this on the ground test unit. Brian Rohrbacher Paul Hendry wrote: Brian, Just out of interest, did you try running both power and data over the new cable and did you still see the same issue? P. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: 15 September 2006 02:43 To: WISPA General List Subject: Re: [WISPA] MT power supplies THE SOLUTION First off. I'm back to a 48v 420mA power supply. To the solution. I ran another cat5 up the tower and plugged it into the RB 532. Now I have one cable for poe and one cable for data, and it all works fine. And check this. My headache went away as soon as the problem did. :) Problem solved. NEXT! Brian Tom DeReggi wrote: Amps don't mean a thing without disclosing Volts, Consider Watts instead. 1300mA at 3V is much different than 1300mA at 18V. The mPCI slot (SR5) is 3.3V. Power to the Motherboard is from 12-48V. W=V*A Tom DeReggi RapidDSL & Wireless, Inc IntAirNet- Fixed Wireless Broadband - Original Message - From: "Mark McElvy" <[EMAIL PROTECTED]> To: &qu
Re: [WISPA] MT power supplies THE SOLUTION
So the question that arises, is why did that fix it? I see two possibilities 1) Poor quality cable or cable shields. (Loss running Ethernet data parallel to power) 2) Sharing a CAT5 jack on the 532 main board for Power and Data. Travis previously talked about the horrid RF interferrence that the 532 board generated when using 48V, due to the 532 onboard power converter/supply. I'm wondering if the distortion/loss was at the board itself apposed to cable? It would have been interesting to know, if you used one cable for both data and power, but terminated the data pairs to a different Ethernet port instead of the POE port used for power. What also would have been interesting would have been to know wether a 18V power supply would have worked on a shared single cable. Different ethernet chipsets do have different characteristics and ranges. So it is possible that just the different chip made the difference based on compatibilty or characteristics of chip. But the other reasons are just as probable. What brand (not just shield type) cable were you using? I realize that you would not likely pursue additional tests as you found a fix already, but it would be interesting to know, just so we can keep collecting data should we experience similar problems in the future. We had a similar situation that was due to chipset. We ran 10 mbps ethernet 550 feet to our subscriber. (different radio brand). We used a slightly higher power voltage to make up for cable loss. Our laptops worked great over the link. The customer's 3 identical routers could not stay connected for long. We were not sure if it was a speed autodetection issue, or the distance for the chip to work. We installed a 10mbps Cisco Switch in between their router and our cable dmarc in their premise, and it all worked. Tom DeReggi RapidDSL & Wireless, Inc IntAirNet- Fixed Wireless Broadband - Original Message - From: "Brian Rohrbacher" <[EMAIL PROTECTED]> To: "WISPA General List" Sent: Friday, September 15, 2006 9:20 AM Subject: Re: [WISPA] MT power supplies THE SOLUTION I started with RB 532 on tower. It comes down 265 feet to poe injector to router. Major packet loss. 2) switched RB 532 out. No change. 3) Created test setup on ground with "bad board" and it looked fine. (from laptop--6ft cablepoe265 ft---RB) 4) Blamed it on the cable, and got a cable certifier from a friend. 5) Right before climb, I re did the test setup on the ground. This time I plugged the 265 feet into the actual router instead of my laptop. The problen was back. (I was bummed) 6) One final test. Get another 265 foot cable. I used 265ft for power and 265ft for data to eth 2 or 3. Problem solved. I can only speculate that the chipset on RB 532 poe port is diffrent from the chipset on eth 2/3. And for whatever reason it was not compatable with cable, hardware, ect.setup. I may never know for sure why, but I have the workaround. Good enough for me. FWIW I ended up pulling 2 new cables (all 3 certified fine). I used the original cable for data (it has "real" shield) I used my new 2 (cheapo foil shield) for power and slapped the other into eth3 for the heck of it. Lessons learned for next time. Measure cable, crimp, and power up on ground using the EXACT same everything as what the final deployment will have. And then test. Hope that sums it all up. Ok to directly answer your question. Yes. I did this on the ground test unit. Brian Rohrbacher Paul Hendry wrote: Brian, Just out of interest, did you try running both power and data over the new cable and did you still see the same issue? P. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: 15 September 2006 02:43 To: WISPA General List Subject: Re: [WISPA] MT power supplies THE SOLUTION First off. I'm back to a 48v 420mA power supply. To the solution. I ran another cat5 up the tower and plugged it into the RB 532. Now I have one cable for poe and one cable for data, and it all works fine. And check this. My headache went away as soon as the problem did. :) Problem solved. NEXT! Brian Tom DeReggi wrote: Amps don't mean a thing without disclosing Volts, Consider Watts instead. 1300mA at 3V is much different than 1300mA at 18V. The mPCI slot (SR5) is 3.3V. Power to the Motherboard is from 12-48V. W=V*A Tom DeReggi RapidDSL & Wireless, Inc IntAirNet- Fixed Wireless Broadband - Original Message - From: "Mark McElvy" <[EMAIL PROTECTED]> To: "WISPA General List" Sent: Wednesday, September 13, 2006 8:19 AM Subject: RE: [WISPA] MT power supplies I am surprised no one has mentioned this. I looked up power consumption on the SR5 and it shows 800 to 1300 mA each. You state your power supply is 700mA. I did not look up power con
Re: [WISPA] MT power supplies THE SOLUTION
Additionally consider, just because something works on the ground doesn;t mean that it will work up in the air, for two reasons. 1) When operating outside of specs, it may take a period of time before the equipment starts to fail and flaws show up. (heat build up, or stress on devices) 2) Interferences stretched along the tower structure for 250 feet, may be different than interferences that exist in a coil at the ground. Take note, that even though COILS can degrade signal, I've tested 500 feet cables on the ground in coils with Trango successfully, but up on a roof, failures at 200 feet in some circumstances. So... first, do the math. second, test on ground. third, prey that it will works after its been installed on the tower. :-) The most important lesson, is to rule out unknowns before you install on the tower. Test IP configurations of radios from laptop. Use patch cables that will be used when testing live. Work with a set of knowns. So you don't have to Climb just to rule something out. And always test before you climb down. Tom DeReggiRapidDSL & Wireless, IncIntAirNet- Fixed Wireless Broadband - Original Message - From: Scott Reed To: WISPA General List Sent: Friday, September 15, 2006 12:48 PM Subject: Re: [WISPA] MT power supplies THE SOLUTION I just looked at that Resources for a 532. 2 Ports are VIA Technologies. The 3rd is Integrated Device Technologies. Scott Reed Owner NewWays Wireless Networking Network Design, Installation and Administration www.nwwnet.net -- Original Message --- From: Brian Rohrbacher <[EMAIL PROTECTED]> To: WISPA General List Sent: Fri, 15 Sep 2006 09:20:58 -0400 Subject: Re: [WISPA] MT power supplies THE SOLUTION > I started with RB 532 on tower. It comes down 265 feet to poe > injector to router. Major packet loss. > 2) switched RB 532 out. No change. > 3) Created test setup on ground with "bad board" and it looked fine. > (from laptop--6ft cablepoe265 ft---RB) > 4) Blamed it on the cable, and got a cable certifier from a friend. > 5) Right before climb, I re did the test setup on the ground. This > time I plugged the 265 feet into the actual router instead of my > laptop. The problen was back. (I was bummed) > 6) One final test. Get another 265 foot cable. I used 265ft for power > and 265ft for data to eth 2 or 3. > Problem solved. > I can only speculate that the chipset on RB 532 poe port is diffrent > from the chipset on eth 2/3. > And for whatever reason it was not compatable with cable, hardware, > ect.setup. > I may never know for sure why, but I have the workaround. Good enough > for me. > > FWIW I ended up pulling 2 new cables (all 3 certified fine). I used > the original cable for data (it has "real" shield) I used my new 2 > (cheapo foil shield) for power and slapped the other into eth3 for the > heck of it. > > Lessons learned for next time. > Measure cable, crimp, and power up on ground using the EXACT same > everything as what the final deployment will have. And then test. > > Hope that sums it all up. > > Ok to directly answer your question. Yes. I did this on the ground > test unit. > > Brian > Rohrbacher > > Paul Hendry wrote: > > >Brian, > > > >Just out of interest, did you try running both power and data over the new > >cable and did you still see the same issue? > > > >P. > > > >-Original Message- > >From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On > >Behalf Of Brian Rohrbacher > >Sent: 15 September 2006 02:43 > >To: WISPA General List > >Subject: Re: [WISPA] MT power supplies THE SOLUTION > > > >First off. I'm back to a 48v 420mA power supply. > >To the solution. > >I ran another cat5 up the tower and plugged it into the RB 532. > >Now I have one cable for poe and one cable for data, and it all works fine. > >And check this. My headache went away as soon as the problem did. :) > >Problem solved. NEXT! > > > >Brian > > > >Tom DeReggi wrote: > > > > > > > >>Amps don't mean a thing without disclosing Volts, Consider Watts > >>instead. 1300mA at 3V is much different than 1300mA at 18V. > >>The mPCI slot (SR5) is 3.3V. Power to the Motherboard is from > >>12-48V. W=V*A > >> > >>Tom DeReggi > >>RapidDSL & Wireless, Inc > >>IntAirNet- Fixed Wireless Broadband > >> > >> > >>- Original Message - From: "Mark McElv
Re: [WISPA] MT power supplies THE SOLUTION
I just looked at that Resources for a 532. 2 Ports are VIA Technologies. The 3rd is Integrated Device Technologies. Scott Reed Owner NewWays Wireless Networking Network Design, Installation and Administration www.nwwnet.net -- Original Message --- From: Brian Rohrbacher <[EMAIL PROTECTED]> To: WISPA General List Sent: Fri, 15 Sep 2006 09:20:58 -0400 Subject: Re: [WISPA] MT power supplies THE SOLUTION > I started with RB 532 on tower. It comes down 265 feet to poe > injector to router. Major packet loss. > 2) switched RB 532 out. No change. > 3) Created test setup on ground with "bad board" and it looked fine. > (from laptop--6ft cablepoe265 ft---RB) > 4) Blamed it on the cable, and got a cable certifier from a friend. > 5) Right before climb, I re did the test setup on the ground. This > time I plugged the 265 feet into the actual router instead of my > laptop. The problen was back. (I was bummed) > 6) One final test. Get another 265 foot cable. I used 265ft for power > and 265ft for data to eth 2 or 3. > Problem solved. > I can only speculate that the chipset on RB 532 poe port is diffrent > from the chipset on eth 2/3. > And for whatever reason it was not compatable with cable, hardware, > ect.setup. > I may never know for sure why, but I have the workaround. Good enough > for me. > > FWIW I ended up pulling 2 new cables (all 3 certified fine). I used > the original cable for data (it has "real" shield) I used my new 2 > (cheapo foil shield) for power and slapped the other into eth3 for the > heck of it. > > Lessons learned for next time. > Measure cable, crimp, and power up on ground using the EXACT same > everything as what the final deployment will have. And then test. > > Hope that sums it all up. > > Ok to directly answer your question. Yes. I did this on the ground > test unit. > > Brian > Rohrbacher > > Paul Hendry wrote: > > >Brian, > > > >Just out of interest, did you try running both power and data over the new > >cable and did you still see the same issue? > > > >P. > > > >-Original Message----- > >From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On > >Behalf Of Brian Rohrbacher > >Sent: 15 September 2006 02:43 > >To: WISPA General List > >Subject: Re: [WISPA] MT power supplies THE SOLUTION > > > >First off. I'm back to a 48v 420mA power supply. > >To the solution. > >I ran another cat5 up the tower and plugged it into the RB 532. > >Now I have one cable for poe and one cable for data, and it all works fine. > >And check this. My headache went away as soon as the problem did. :) > >Problem solved. NEXT! > > > >Brian > > > >Tom DeReggi wrote: > > > > > > > >>Amps don't mean a thing without disclosing Volts, Consider Watts > >>instead. 1300mA at 3V is much different than 1300mA at 18V. > >>The mPCI slot (SR5) is 3.3V. Power to the Motherboard is from > >>12-48V. W=V*A > >> > >>Tom DeReggi > >>RapidDSL & Wireless, Inc > >>IntAirNet- Fixed Wireless Broadband > >> > >> > >>- Original Message - From: "Mark McElvy" <[EMAIL PROTECTED]> > >>To: "WISPA General List" > >>Sent: Wednesday, September 13, 2006 8:19 AM > >>Subject: RE: [WISPA] MT power supplies > >> > >> > >>I am surprised no one has mentioned this. I looked up power consumption > >>on the SR5 and it shows 800 to 1300 mA each. You state your power supply > >>is 700mA. I did not look up power consumption for the RB532 but I would > >>think you would need at least a 3A supply. > >> > >>-Original Message- > >>From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On > >>Behalf Of Brian Rohrbacher > >>Sent: Tuesday, September 12, 2006 11:51 AM > >>To: WISPA General List > >>Subject: Re: [WISPA] MT power supplies > >> > >>So, does anyone know if it looks like I would be fine on the power side > >>of things? > >>I have tweaked the ethernet port settings for no gain. > >> > >>Next step is to get climbing 280ft to replace board, but I'd like to > >>confirm power first.
Re: [WISPA] MT power supplies THE SOLUTION
Brian, did you try the "long cable" setting on that particular interface ? Brian Rohrbacher wrote: I started with RB 532 on tower. It comes down 265 feet to poe injector to router. Major packet loss. 2) switched RB 532 out. No change. 3) Created test setup on ground with "bad board" and it looked fine. (from laptop--6ft cablepoe265 ft---RB) 4) Blamed it on the cable, and got a cable certifier from a friend. 5) Right before climb, I re did the test setup on the ground. This time I plugged the 265 feet into the actual router instead of my laptop. The problen was back. (I was bummed) 6) One final test. Get another 265 foot cable. I used 265ft for power and 265ft for data to eth 2 or 3. Problem solved. I can only speculate that the chipset on RB 532 poe port is diffrent from the chipset on eth 2/3. And for whatever reason it was not compatable with cable, hardware, ect.setup. I may never know for sure why, but I have the workaround. Good enough for me. FWIW I ended up pulling 2 new cables (all 3 certified fine). I used the original cable for data (it has "real" shield) I used my new 2 (cheapo foil shield) for power and slapped the other into eth3 for the heck of it. Lessons learned for next time. Measure cable, crimp, and power up on ground using the EXACT same everything as what the final deployment will have. And then test. Hope that sums it all up. Ok to directly answer your question. Yes. I did this on the ground test unit. Brian Rohrbacher Paul Hendry wrote: Brian, Just out of interest, did you try running both power and data over the new cable and did you still see the same issue? P. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: 15 September 2006 02:43 To: WISPA General List Subject: Re: [WISPA] MT power supplies THE SOLUTION First off. I'm back to a 48v 420mA power supply. To the solution. I ran another cat5 up the tower and plugged it into the RB 532. Now I have one cable for poe and one cable for data, and it all works fine. And check this. My headache went away as soon as the problem did. :) Problem solved. NEXT! Brian Tom DeReggi wrote: Amps don't mean a thing without disclosing Volts, Consider Watts instead. 1300mA at 3V is much different than 1300mA at 18V. The mPCI slot (SR5) is 3.3V. Power to the Motherboard is from 12-48V. W=V*A Tom DeReggi RapidDSL & Wireless, Inc IntAirNet- Fixed Wireless Broadband - Original Message - From: "Mark McElvy" <[EMAIL PROTECTED]> To: "WISPA General List" Sent: Wednesday, September 13, 2006 8:19 AM Subject: RE: [WISPA] MT power supplies I am surprised no one has mentioned this. I looked up power consumption on the SR5 and it shows 800 to 1300 mA each. You state your power supply is 700mA. I did not look up power consumption for the RB532 but I would think you would need at least a 3A supply. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 11:51 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies THE SOLUTION
I started with RB 532 on tower. It comes down 265 feet to poe injector to router. Major packet loss. 2) switched RB 532 out. No change. 3) Created test setup on ground with "bad board" and it looked fine. (from laptop--6ft cablepoe265 ft---RB) 4) Blamed it on the cable, and got a cable certifier from a friend. 5) Right before climb, I re did the test setup on the ground. This time I plugged the 265 feet into the actual router instead of my laptop. The problen was back. (I was bummed) 6) One final test. Get another 265 foot cable. I used 265ft for power and 265ft for data to eth 2 or 3. Problem solved. I can only speculate that the chipset on RB 532 poe port is diffrent from the chipset on eth 2/3. And for whatever reason it was not compatable with cable, hardware, ect.setup. I may never know for sure why, but I have the workaround. Good enough for me. FWIW I ended up pulling 2 new cables (all 3 certified fine). I used the original cable for data (it has "real" shield) I used my new 2 (cheapo foil shield) for power and slapped the other into eth3 for the heck of it. Lessons learned for next time. Measure cable, crimp, and power up on ground using the EXACT same everything as what the final deployment will have. And then test. Hope that sums it all up. Ok to directly answer your question. Yes. I did this on the ground test unit. Brian Rohrbacher Paul Hendry wrote: Brian, Just out of interest, did you try running both power and data over the new cable and did you still see the same issue? P. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: 15 September 2006 02:43 To: WISPA General List Subject: Re: [WISPA] MT power supplies THE SOLUTION First off. I'm back to a 48v 420mA power supply. To the solution. I ran another cat5 up the tower and plugged it into the RB 532. Now I have one cable for poe and one cable for data, and it all works fine. And check this. My headache went away as soon as the problem did. :) Problem solved. NEXT! Brian Tom DeReggi wrote: Amps don't mean a thing without disclosing Volts, Consider Watts instead. 1300mA at 3V is much different than 1300mA at 18V. The mPCI slot (SR5) is 3.3V. Power to the Motherboard is from 12-48V. W=V*A Tom DeReggi RapidDSL & Wireless, Inc IntAirNet- Fixed Wireless Broadband - Original Message - From: "Mark McElvy" <[EMAIL PROTECTED]> To: "WISPA General List" Sent: Wednesday, September 13, 2006 8:19 AM Subject: RE: [WISPA] MT power supplies I am surprised no one has mentioned this. I looked up power consumption on the SR5 and it shows 800 to 1300 mA each. You state your power supply is 700mA. I did not look up power consumption for the RB532 but I would think you would need at least a 3A supply. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 11:51 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies THE SOLUTION
I was on 48v from the start. But I tested 4 48v power supplies300, 420, 700, and 1000mA units. None of that had any effect. The seperate cables. One for power, one for data fixed it. Brian George Rogato wrote: Good call Brian, Being an electrician all of my previous working life, voltage drop is a serious consideration at 300', even with 120 volts. Solution has always been to increase the voltage to reduce the amperage to control voltage drop. That is why you see transformers all over the place. I like 48 Volts a whole lot more than 24 volts. George Brian Rohrbacher wrote: First off. I'm back to a 48v 420mA power supply. To the solution. I ran another cat5 up the tower and plugged it into the RB 532. Now I have one cable for poe and one cable for data, and it all works fine. And check this. My headache went away as soon as the problem did. :) Problem solved. NEXT! Brian Tom DeReggi wrote: Amps don't mean a thing without disclosing Volts, Consider Watts instead. 1300mA at 3V is much different than 1300mA at 18V. The mPCI slot (SR5) is 3.3V. Power to the Motherboard is from 12-48V. W=V*A Tom DeReggi RapidDSL & Wireless, Inc IntAirNet- Fixed Wireless Broadband - Original Message - From: "Mark McElvy" <[EMAIL PROTECTED]> To: "WISPA General List" Sent: Wednesday, September 13, 2006 8:19 AM Subject: RE: [WISPA] MT power supplies I am surprised no one has mentioned this. I looked up power consumption on the SR5 and it shows 800 to 1300 mA each. You state your power supply is 700mA. I did not look up power consumption for the RB532 but I would think you would need at least a 3A supply. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 11:51 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
RE: [WISPA] MT power supplies THE SOLUTION
Brian, Just out of interest, did you try running both power and data over the new cable and did you still see the same issue? P. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: 15 September 2006 02:43 To: WISPA General List Subject: Re: [WISPA] MT power supplies THE SOLUTION First off. I'm back to a 48v 420mA power supply. To the solution. I ran another cat5 up the tower and plugged it into the RB 532. Now I have one cable for poe and one cable for data, and it all works fine. And check this. My headache went away as soon as the problem did. :) Problem solved. NEXT! Brian Tom DeReggi wrote: > Amps don't mean a thing without disclosing Volts, Consider Watts > instead. 1300mA at 3V is much different than 1300mA at 18V. > The mPCI slot (SR5) is 3.3V. Power to the Motherboard is from > 12-48V. W=V*A > > Tom DeReggi > RapidDSL & Wireless, Inc > IntAirNet- Fixed Wireless Broadband > > > - Original Message - From: "Mark McElvy" <[EMAIL PROTECTED]> > To: "WISPA General List" > Sent: Wednesday, September 13, 2006 8:19 AM > Subject: RE: [WISPA] MT power supplies > > > I am surprised no one has mentioned this. I looked up power consumption > on the SR5 and it shows 800 to 1300 mA each. You state your power supply > is 700mA. I did not look up power consumption for the RB532 but I would > think you would need at least a 3A supply. > > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On > Behalf Of Brian Rohrbacher > Sent: Tuesday, September 12, 2006 11:51 AM > To: WISPA General List > Subject: Re: [WISPA] MT power supplies > > So, does anyone know if it looks like I would be fine on the power side > of things? > I have tweaked the ethernet port settings for no gain. > > Next step is to get climbing 280ft to replace board, but I'd like to > confirm power first. > > Brian > > Brian Rohrbacher wrote: > >> I have a RB 532 on 300 foot of cat 5 with 2 sr5. >> I'm using poe 48v .700a power supply. >> I'm seeing weirdness. >> >> Do I have enough "juice" >> >> Brian > > -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -- No virus found in this incoming message. Checked by AVG Free Edition. Version: 7.1.405 / Virus Database: 268.12.3/447 - Release Date: 13/09/2006 -- No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.1.405 / Virus Database: 268.12.4/448 - Release Date: 14/09/2006 -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies THE SOLUTION
Good call Brian, Being an electrician all of my previous working life, voltage drop is a serious consideration at 300', even with 120 volts. Solution has always been to increase the voltage to reduce the amperage to control voltage drop. That is why you see transformers all over the place. I like 48 Volts a whole lot more than 24 volts. George Brian Rohrbacher wrote: First off. I'm back to a 48v 420mA power supply. To the solution. I ran another cat5 up the tower and plugged it into the RB 532. Now I have one cable for poe and one cable for data, and it all works fine. And check this. My headache went away as soon as the problem did. :) Problem solved. NEXT! Brian Tom DeReggi wrote: Amps don't mean a thing without disclosing Volts, Consider Watts instead. 1300mA at 3V is much different than 1300mA at 18V. The mPCI slot (SR5) is 3.3V. Power to the Motherboard is from 12-48V. W=V*A Tom DeReggi RapidDSL & Wireless, Inc IntAirNet- Fixed Wireless Broadband - Original Message - From: "Mark McElvy" <[EMAIL PROTECTED]> To: "WISPA General List" Sent: Wednesday, September 13, 2006 8:19 AM Subject: RE: [WISPA] MT power supplies I am surprised no one has mentioned this. I looked up power consumption on the SR5 and it shows 800 to 1300 mA each. You state your power supply is 700mA. I did not look up power consumption for the RB532 but I would think you would need at least a 3A supply. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 11:51 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- George Rogato Welcome to WISPA www.wispa.org http://signup.wispa.org/ -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies THE SOLUTION
First off. I'm back to a 48v 420mA power supply. To the solution. I ran another cat5 up the tower and plugged it into the RB 532. Now I have one cable for poe and one cable for data, and it all works fine. And check this. My headache went away as soon as the problem did. :) Problem solved. NEXT! Brian Tom DeReggi wrote: Amps don't mean a thing without disclosing Volts, Consider Watts instead. 1300mA at 3V is much different than 1300mA at 18V. The mPCI slot (SR5) is 3.3V. Power to the Motherboard is from 12-48V. W=V*A Tom DeReggi RapidDSL & Wireless, Inc IntAirNet- Fixed Wireless Broadband - Original Message - From: "Mark McElvy" <[EMAIL PROTECTED]> To: "WISPA General List" Sent: Wednesday, September 13, 2006 8:19 AM Subject: RE: [WISPA] MT power supplies I am surprised no one has mentioned this. I looked up power consumption on the SR5 and it shows 800 to 1300 mA each. You state your power supply is 700mA. I did not look up power consumption for the RB532 but I would think you would need at least a 3A supply. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 11:51 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies
Amps don't mean a thing without disclosing Volts, Consider Watts instead. 1300mA at 3V is much different than 1300mA at 18V. The mPCI slot (SR5) is 3.3V. Power to the Motherboard is from 12-48V. W=V*A Tom DeReggi RapidDSL & Wireless, Inc IntAirNet- Fixed Wireless Broadband - Original Message - From: "Mark McElvy" <[EMAIL PROTECTED]> To: "WISPA General List" Sent: Wednesday, September 13, 2006 8:19 AM Subject: RE: [WISPA] MT power supplies I am surprised no one has mentioned this. I looked up power consumption on the SR5 and it shows 800 to 1300 mA each. You state your power supply is 700mA. I did not look up power consumption for the RB532 but I would think you would need at least a 3A supply. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 11:51 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ This electronic communication (including any attached document) may contain privileged and/or confidential information. This communication is intended only for the use of indicated e-mail addressees. If you are not an intended recipient of this communication, please be advised that any disclosure, dissemination, distribution, copying, or other use of this communication or any attached document is prohibited. If you have received this communication in error, please notify the sender immediately by reply e-mail and promptly destroy all electronic and printed copies of this communication and any attached document. Unauthorized interception of this e-mail is a violation of federal criminal law. -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -- No virus found in this incoming message. Checked by AVG Free Edition. Version: 7.1.405 / Virus Database: 268.12.3/445 - Release Date: 9/11/2006 -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
RE: [WISPA] MT power supplies
We have had a couple of cables that have shown link lights and passed data sporadically. We replaced the cable and it worked fine after that. The cable did NOT pass the tester though. :-) -Hal __ Harold Bledsoe Deliberant LLC 800.742.9865 x205 [EMAIL PROTECTED] http://www.deliberant.com -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Wednesday, September 13, 2006 2:33 PM To: WISPA General List Subject: Re: [WISPA] MT power supplies Oh, I was thinking re transmitions. Like lost or bad or partial packets or something...DOH! The answer. 1 cable. POE port to POE injector. Cable test to be preformed in a could hours. Brian Paul Hendry wrote: >When I say re-terminations I mean do you have a single cat5 cable from >PoE injector to RB532 or do you use any fly leads. Also, do you >terminate the outdoor cat5 to a connector on the AP then a further >internal short cat5 to the RB532? > > > >>>Also, how many re-terminations do you have between the power injector >>>and the RB532? >>> >>> >>> >>> >>> >>Where do I find this info? >> >>Brian >> >> > > >-Original Message- >From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On >Behalf Of Brian Rohrbacher >Sent: 13 September 2006 13:25 >To: WISPA General List >Subject: Re: [WISPA] MT power supplies > > > >Paul Hendry wrote: > > > >>Have you tried just using a different PSU with higher voltage and >>higher ampage? >> >> >> >yes. I actually even set up a second test link on the ground with the >"bad" board I just took down. I tested with an extra 11 foot of cat5 >five on my ground test (276, not the 265 in the air). >The ethernet link was fine. Bandwidth test showed me sending 24mb >(laptop cpu maxed) vs the 3mb I can send at the tower site. I can >receive 14mb (RB cpu maxed) vs the 5mb I get at the tower site. >I have a fancy cable tester coming from a guy I know. We'll see what >it finds. > > > >>Also, how many re-terminations do you have between the power injector >>and the RB532? >> >> >> >> >> >Where do I find this info? > >Brian > > > >>P. >> >>-Original Message- >>From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] >>On Behalf Of Brian Rohrbacher >>Sent: 12 September 2006 17:51 >>To: WISPA General List >>Subject: Re: [WISPA] MT power supplies >> >>So, does anyone know if it looks like I would be fine on the power >>side of things? >>I have tweaked the ethernet port settings for no gain. >> >>Next step is to get climbing 280ft to replace board, but I'd like to >>confirm power first. >> >>Brian >> >>Brian Rohrbacher wrote: >> >> >> >> >> >>>I have a RB 532 on 300 foot of cat 5 with 2 sr5. >>>I'm using poe 48v .700a power supply. >>>I'm seeing weirdness. >>> >>>Do I have enough "juice" >>> >>>Brian >>> >>> >>> >>> >> >> >> >> -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies
Oh, I was thinking re transmitions. Like lost or bad or partial packets or something...DOH! The answer. 1 cable. POE port to POE injector. Cable test to be preformed in a could hours. Brian Paul Hendry wrote: When I say re-terminations I mean do you have a single cat5 cable from PoE injector to RB532 or do you use any fly leads. Also, do you terminate the outdoor cat5 to a connector on the AP then a further internal short cat5 to the RB532? Also, how many re-terminations do you have between the power injector and the RB532? Where do I find this info? Brian -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: 13 September 2006 13:25 To: WISPA General List Subject: Re: [WISPA] MT power supplies Paul Hendry wrote: Have you tried just using a different PSU with higher voltage and higher ampage? yes. I actually even set up a second test link on the ground with the "bad" board I just took down. I tested with an extra 11 foot of cat5 five on my ground test (276, not the 265 in the air). The ethernet link was fine. Bandwidth test showed me sending 24mb (laptop cpu maxed) vs the 3mb I can send at the tower site. I can receive 14mb (RB cpu maxed) vs the 5mb I get at the tower site. I have a fancy cable tester coming from a guy I know. We'll see what it finds. Also, how many re-terminations do you have between the power injector and the RB532? Where do I find this info? Brian P. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: 12 September 2006 17:51 To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
RE: [WISPA] MT power supplies
When I say re-terminations I mean do you have a single cat5 cable from PoE injector to RB532 or do you use any fly leads. Also, do you terminate the outdoor cat5 to a connector on the AP then a further internal short cat5 to the RB532? >>Also, how many re-terminations do you have between the power >>injector and the RB532? >> >> >> >Where do I find this info? > >Brian -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: 13 September 2006 13:25 To: WISPA General List Subject: Re: [WISPA] MT power supplies Paul Hendry wrote: >Have you tried just using a different PSU with higher voltage and higher >ampage? > yes. I actually even set up a second test link on the ground with the "bad" board I just took down. I tested with an extra 11 foot of cat5 five on my ground test (276, not the 265 in the air). The ethernet link was fine. Bandwidth test showed me sending 24mb (laptop cpu maxed) vs the 3mb I can send at the tower site. I can receive 14mb (RB cpu maxed) vs the 5mb I get at the tower site. I have a fancy cable tester coming from a guy I know. We'll see what it finds. >Also, how many re-terminations do you have between the power >injector and the RB532? > > > Where do I find this info? Brian >P. > >-Original Message- >From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On >Behalf Of Brian Rohrbacher >Sent: 12 September 2006 17:51 >To: WISPA General List >Subject: Re: [WISPA] MT power supplies > >So, does anyone know if it looks like I would be fine on the power side >of things? >I have tweaked the ethernet port settings for no gain. > >Next step is to get climbing 280ft to replace board, but I'd like to >confirm power first. > >Brian > >Brian Rohrbacher wrote: > > > >>I have a RB 532 on 300 foot of cat 5 with 2 sr5. >>I'm using poe 48v .700a power supply. >>I'm seeing weirdness. >> >>Do I have enough "juice" >> >>Brian >> >> > > > -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -- No virus found in this incoming message. Checked by AVG Free Edition. Version: 7.1.405 / Virus Database: 268.12.3/446 - Release Date: 12/09/2006 -- No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.1.405 / Virus Database: 268.12.3/446 - Release Date: 12/09/2006 -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
RE: [WISPA] MT power supplies
I would check the terminations and maybe re-terminate them, especially if you have verified with a new cable that it works ok. -Hal -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Wednesday, September 13, 2006 10:10 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies Yes, ethernet is shielded. The good stuff. It's like almost 1/2 inch cat5. The tower has pagers, lots of trango, few backhauls, canopy 900, and some more I believe. The only thing up with me is some trango, and they have no problem. I am pointing at a bad cable. Brian Harold Bledsoe wrote: >The 800 to 1300mA consumption is at 3.3V. The 700mA from the PS is at >48V so there is probably plenty of power going to it. > >Is the CAT5 shielded? What else is on the tower? > >-Hal > > >-Original Message- >From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On >Behalf Of Mark McElvy >Sent: Wednesday, September 13, 2006 8:20 AM >To: WISPA General List >Subject: RE: [WISPA] MT power supplies > >I am surprised no one has mentioned this. I looked up power consumption >on the SR5 and it shows 800 to 1300 mA each. You state your power supply >is 700mA. I did not look up power consumption for the RB532 but I would >think you would need at least a 3A supply. > >-Original Message- >From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On >Behalf Of Brian Rohrbacher >Sent: Tuesday, September 12, 2006 11:51 AM >To: WISPA General List >Subject: Re: [WISPA] MT power supplies > >So, does anyone know if it looks like I would be fine on the power side >of things? >I have tweaked the ethernet port settings for no gain. > >Next step is to get climbing 280ft to replace board, but I'd like to >confirm power first. > >Brian > >Brian Rohrbacher wrote: > > > >>I have a RB 532 on 300 foot of cat 5 with 2 sr5. >>I'm using poe 48v .700a power supply. >>I'm seeing weirdness. >> >>Do I have enough "juice" >> >>Brian >> >> > > > -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies
Yes, ethernet is shielded. The good stuff. It's like almost 1/2 inch cat5. The tower has pagers, lots of trango, few backhauls, canopy 900, and some more I believe. The only thing up with me is some trango, and they have no problem. I am pointing at a bad cable. Brian Harold Bledsoe wrote: The 800 to 1300mA consumption is at 3.3V. The 700mA from the PS is at 48V so there is probably plenty of power going to it. Is the CAT5 shielded? What else is on the tower? -Hal -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Mark McElvy Sent: Wednesday, September 13, 2006 8:20 AM To: WISPA General List Subject: RE: [WISPA] MT power supplies I am surprised no one has mentioned this. I looked up power consumption on the SR5 and it shows 800 to 1300 mA each. You state your power supply is 700mA. I did not look up power consumption for the RB532 but I would think you would need at least a 3A supply. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 11:51 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
RE: [WISPA] MT power supplies
The 800 to 1300mA consumption is at 3.3V. The 700mA from the PS is at 48V so there is probably plenty of power going to it. Is the CAT5 shielded? What else is on the tower? -Hal -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Mark McElvy Sent: Wednesday, September 13, 2006 8:20 AM To: WISPA General List Subject: RE: [WISPA] MT power supplies I am surprised no one has mentioned this. I looked up power consumption on the SR5 and it shows 800 to 1300 mA each. You state your power supply is 700mA. I did not look up power consumption for the RB532 but I would think you would need at least a 3A supply. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 11:51 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: > I have a RB 532 on 300 foot of cat 5 with 2 sr5. > I'm using poe 48v .700a power supply. > I'm seeing weirdness. > > Do I have enough "juice" > > Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ This electronic communication (including any attached document) may contain privileged and/or confidential information. This communication is intended only for the use of indicated e-mail addressees. If you are not an intended recipient of this communication, please be advised that any disclosure, dissemination, distribution, copying, or other use of this communication or any attached document is prohibited. If you have received this communication in error, please notify the sender immediately by reply e-mail and promptly destroy all electronic and printed copies of this communication and any attached document. Unauthorized interception of this e-mail is a violation of federal criminal law. -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies
Anyone have a source for a power supply like this? Mark McElvy wrote: I am surprised no one has mentioned this. I looked up power consumption on the SR5 and it shows 800 to 1300 mA each. You state your power supply is 700mA. I did not look up power consumption for the RB532 but I would think you would need at least a 3A supply. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 11:51 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies
Those are the numbers I was looking for. This is a lot more power supply than I currently have. Mark McElvy wrote: I am surprised no one has mentioned this. I looked up power consumption on the SR5 and it shows 800 to 1300 mA each. You state your power supply is 700mA. I did not look up power consumption for the RB532 but I would think you would need at least a 3A supply. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 11:51 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
RE: [WISPA] MT power supplies
I am surprised no one has mentioned this. I looked up power consumption on the SR5 and it shows 800 to 1300 mA each. You state your power supply is 700mA. I did not look up power consumption for the RB532 but I would think you would need at least a 3A supply. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 11:51 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: > I have a RB 532 on 300 foot of cat 5 with 2 sr5. > I'm using poe 48v .700a power supply. > I'm seeing weirdness. > > Do I have enough "juice" > > Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ This electronic communication (including any attached document) may contain privileged and/or confidential information. This communication is intended only for the use of indicated e-mail addressees. If you are not an intended recipient of this communication, please be advised that any disclosure, dissemination, distribution, copying, or other use of this communication or any attached document is prohibited. If you have received this communication in error, please notify the sender immediately by reply e-mail and promptly destroy all electronic and printed copies of this communication and any attached document. Unauthorized interception of this e-mail is a violation of federal criminal law. -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies
Paul Hendry wrote: Have you tried just using a different PSU with higher voltage and higher ampage? yes. I actually even set up a second test link on the ground with the "bad" board I just took down. I tested with an extra 11 foot of cat5 five on my ground test (276, not the 265 in the air). The ethernet link was fine. Bandwidth test showed me sending 24mb (laptop cpu maxed) vs the 3mb I can send at the tower site. I can receive 14mb (RB cpu maxed) vs the 5mb I get at the tower site. I have a fancy cable tester coming from a guy I know. We'll see what it finds. Also, how many re-terminations do you have between the power injector and the RB532? Where do I find this info? Brian P. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: 12 September 2006 17:51 To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
RE: [WISPA] MT power supplies
Have you tried just using a different PSU with higher voltage and higher ampage? Also, how many re-terminations do you have between the power injector and the RB532? P. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: 12 September 2006 17:51 To: WISPA General List Subject: Re: [WISPA] MT power supplies So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: > I have a RB 532 on 300 foot of cat 5 with 2 sr5. > I'm using poe 48v .700a power supply. > I'm seeing weirdness. > > Do I have enough "juice" > > Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -- No virus found in this incoming message. Checked by AVG Free Edition. Version: 7.1.405 / Virus Database: 268.12.3/445 - Release Date: 11/09/2006 -- No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.1.405 / Virus Database: 268.12.3/446 - Release Date: 12/09/2006 -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
RE: [WISPA] MT power supplies
Brian, Have you tried to turn the power down on the SR5's to see if that's the problem? Mac Dearman -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 9:17 PM To: WISPA General List Subject: Re: [WISPA] MT power supplies I climbed and swapped RB532 and it is still messing up. Exact cable length is 265ft. Eth port to poe injector. How do I figure out if this is too far for 2 sr5? This is running nstream. Brian Brian Rohrbacher wrote: > So, does anyone know if it looks like I would be fine on the power > side of things? > I have tweaked the ethernet port settings for no gain. > > Next step is to get climbing 280ft to replace board, but I'd like to > confirm power first. > > Brian > > Brian Rohrbacher wrote: > >> I have a RB 532 on 300 foot of cat 5 with 2 sr5. >> I'm using poe 48v .700a power supply. >> I'm seeing weirdness. >> >> Do I have enough "juice" >> >> Brian > > -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies
I climbed and swapped RB532 and it is still messing up. Exact cable length is 265ft. Eth port to poe injector. How do I figure out if this is too far for 2 sr5? This is running nstream. Brian Brian Rohrbacher wrote: So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies
So, does anyone know if it looks like I would be fine on the power side of things? I have tweaked the ethernet port settings for no gain. Next step is to get climbing 280ft to replace board, but I'd like to confirm power first. Brian Brian Rohrbacher wrote: I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies (long cable mode)
I think I found it. Thanks, all. I'll let you know the results. http://forum.mikrotik.com/viewtopic.php?t=210&highlight=long+cable&sid=5d5d6558c2bc21460b84df74a2cba94b Brian Brian Rohrbacher wrote: I'm already at 10mb half. Where is this long cable setting? Brian JohnnyO wrote: Ethernet port acting up ? As in connecting / disconnecting ? Make sure you have it set for "long cable", if that doesn't work - disable auto-negotiation and try 100mbps half duplex, if that don't work - 10mbps full duplex and then last try 10mbps HALF duplex.. JohnnyO x -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 7:56 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies It's actually the ethernet port acting up. Thought maybe it was lack of power. Mac Dearman wrote: I don't think a RB532 will run 2 SR5's with a 2' patch cable and a 48VDC power supply without s0me weirdness happening. I only put one Super Range card in a RB532 and one Atheros or Prism card. Mac -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Monday, September 11, 2006 11:29 PM To: Conversations over a new WISP Trade Organization Subject: [WISPA] MT power supplies I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies
I'm already at 10mb half. Where is this long cable setting? Brian JohnnyO wrote: Ethernet port acting up ? As in connecting / disconnecting ? Make sure you have it set for "long cable", if that doesn't work - disable auto-negotiation and try 100mbps half duplex, if that don't work - 10mbps full duplex and then last try 10mbps HALF duplex.. JohnnyO x -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 7:56 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies It's actually the ethernet port acting up. Thought maybe it was lack of power. Mac Dearman wrote: I don't think a RB532 will run 2 SR5's with a 2' patch cable and a 48VDC power supply without s0me weirdness happening. I only put one Super Range card in a RB532 and one Atheros or Prism card. Mac -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Monday, September 11, 2006 11:29 PM To: Conversations over a new WISP Trade Organization Subject: [WISPA] MT power supplies I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
RE: [WISPA] MT power supplies
Ethernet port acting up ? As in connecting / disconnecting ? Make sure you have it set for "long cable", if that doesn't work - disable auto-negotiation and try 100mbps half duplex, if that don't work - 10mbps full duplex and then last try 10mbps HALF duplex.. JohnnyO x -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Tuesday, September 12, 2006 7:56 AM To: WISPA General List Subject: Re: [WISPA] MT power supplies It's actually the ethernet port acting up. Thought maybe it was lack of power. Mac Dearman wrote: > I don't think a RB532 will run 2 SR5's with a 2' patch cable and a >48VDC power supply without s0me weirdness happening. I only put one >Super Range card in a RB532 and one Atheros or Prism card. > >Mac > > >-Original Message- >From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On >Behalf Of Brian Rohrbacher >Sent: Monday, September 11, 2006 11:29 PM >To: Conversations over a new WISP Trade Organization >Subject: [WISPA] MT power supplies > >I have a RB 532 on 300 foot of cat 5 with 2 sr5. >I'm using poe 48v .700a power supply. >I'm seeing weirdness. > >Do I have enough "juice" > >Brian > > -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
Re: [WISPA] MT power supplies
It's actually the ethernet port acting up. Thought maybe it was lack of power. Mac Dearman wrote: I don't think a RB532 will run 2 SR5's with a 2' patch cable and a 48VDC power supply without s0me weirdness happening. I only put one Super Range card in a RB532 and one Atheros or Prism card. Mac -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Monday, September 11, 2006 11:29 PM To: Conversations over a new WISP Trade Organization Subject: [WISPA] MT power supplies I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
RE: [WISPA] MT power supplies
I don't think a RB532 will run 2 SR5's with a 2' patch cable and a 48VDC power supply without s0me weirdness happening. I only put one Super Range card in a RB532 and one Atheros or Prism card. Mac -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Brian Rohrbacher Sent: Monday, September 11, 2006 11:29 PM To: Conversations over a new WISP Trade Organization Subject: [WISPA] MT power supplies I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
[WISPA] MT power supplies
I have a RB 532 on 300 foot of cat 5 with 2 sr5. I'm using poe 48v .700a power supply. I'm seeing weirdness. Do I have enough "juice" Brian -- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/