t any more, to Elecraft specific topics. This one has
wandered well afield of Elecraft.
73,
Rick nk7i
On 5/4/2024 9:21 PM, Jorge Diez - CX6VM wrote:
Hi Dave
I have a panel like yours, each antenna to a discharger, on a copper sheet.
Nothing has happened with the coaxial and antenna swit
No content, please use plain text when sending to THIS list. (no
formatting or HTML)
Thank you,
Rick nk7i
On 5/4/2024 10:59 AM, Ray wrote:
__
Elecraft mailing list
Home:http://mailman.qth.net/mailman/listinfo/elecraft
Help:http
times during use.
73,
Rick nk7i
* Lightning protection how-to or discussion is beyond the scope of this
group, but EVERY STATION should have a system in place WITH grounding
and bonding of every item in the shack, includes every wire that enters
the building (cable TV, phone, power, DSL
the entire
antenna and feed system to be sure.
Or you can dive in to repair it; if you feel qualified.
Sorry, been there too.
Rick nk7i
On 4/23/2024 6:52 PM, Dick Bingham wrote:
Greeting to everyone
I have read the KPA500 operator manual in hopes of solving my
issue and have found nothing
Check the menu setting? Not Inst?
73,
Rick nk7i
On 4/17/2024 8:39 PM, Robie Elms wrote:
Dave,
Mark sure you do not have the AUX antenna selected for your sub receiver.
Push and Hold the RX ANT button and change it from Main to AUX or vice
versa. This selection is band sensitive.
Robie
Fn | Updates | Release Notes
will show you what you're looking for. R35 updated the front display code.
73,
Rick nk7i
On 4/10/2024 10:42 AM, Bob wrote:
I installed version R35 today, but didn't see any release notes as part of
the update, or on the elecraft website itself.
Any idea what
Using the utility, erase the settings for 20M and reteach it? Once
trained, leave it in MAN mode for daily use.
73,
Rick nk7i
On 4/9/2024 8:30 AM, Mike Murray wrote:
My KAT500 will no longer tune in AUTO mode on 20M and does not change to
prior stored settings in MAN mode. All other bands
Correct.
73,
Rick nk7i
On 4/6/2024 12:03 PM, Fred Jensen wrote:
Hmmm ... I thought that the ALC started AT the 5th bar and the first 4
bars were sort of a VU-meter. Hence Don's occasional advice, "4 full
bars and the 5th occasionally flickering." I've been known to get
th
the next couple weeks
were adjusted to my operating preferences (DXing) and local conditions.
K3 to K4 transition is not a steep learning curve; but they are two
different rigs, there IS a curve. (Kenwood to Elecraft, slightly
steeper. "Other" brands, steeper again but MUCH simpler.)
Think it through, it is an ANTENNA tuner (matching circuit). You disable all
of them along the path (BYPASS), EXCEPT at the antenna connection.
It is presumptive 50 ohm to 50 ohm resistive at each stage, no tuner required,
except for the antenna.
73,
Rick nk7i
> On Mar 11, 2024, at 12
Did you check the filter settings (or filter) on the sub?
73,
Rick nk7i
On 1/24/2024 3:35 PM, Michael Carter via Elecraft wrote:
Hi Pete,
If you've confirmed that the RX ANT is NOT selected
on the 80 meter band for the sub-RX, I would
check the CONFIG entry for the KRX3 to be sure
that it's
Flex isn’t cheap either but the wait for non-warranty repair tells Elecrafters
waiting; hold my beer. A month minimum, often longer.
73,
Rick NK7I
> On Dec 15, 2023, at 12:25 PM, Pete Smith N4ZR wrote:
>
> That said, does anyone think it's acceptable to have even a 4-week hold
isn't a topic to be discussed on this list.
Across my Starlink LAN (I have two LAN), it's working beautifully and
should be available 'real soon now' for public beta... have some
patience yet while the field test team runs it through it's paces and
some spit and polish are applied.
73,
Rick
I'm glad you found the cause and a fix.
I'll add that, in my experience, 40M is always the most problematic band
for causing RFI problems. In a vehicle or home, it seems that a LOT of
'stuff' is sensitive to 40M. 160M comes in second for that status.
73,
Rick nk7i
On 11/21/2023 2:55 PM
,
transformers, wires etc) has broken down (high voltages are possible
causes). Something changed, you know where to look now. Be ready to
replace the antenna with the means to prevent another similar failure.
73,
Rick nk7i
On 11/20/2023 7:16 PM, Victor Rosenthal 4X6GP wrote:
This is really
efficient at 6M, limit the output to
no more than 1 KW (ask me how I know).
I use the default speeds, but I'm also uncomfortable with it going above
65C, so I step in at that point and boost the fans.
73,
Rick nk7i
On 11/10/2023 11:34 AM, Jim Brown wrote:
I've been told by someone who knows
, the fan can make some noise.
The lower output that you run, the less efficient the amp is, which is
total power used (presented as heat) to output power. Sometimes (30M),
that's the cost (the K3/4 won't produce the US legal limit of 200 watts,
without the amp).
73,
Rick nk7i
On 11/10/2023 11:14
Wayne said that he expects within 1-2 weeks. Without sounding
insulting, sometimes he's right about that.
https://youtu.be/YtV24qha2Uc
73,
Rick nk7i
On 10/27/2023 4:44 PM, Pete Meier via Elecraft wrote:
When is the KH1 reasonably expected to start shipping? No wild guesses please.
Pete
(mostly) are used in the
KAT500 (just larger sizes) which also has a low failure rate.
Instead of guessing, answers of actual failures would provide data points.
73,
Rick nk7i
On 10/13/2023 11:56 AM, David Gilbert wrote:
I am reasonably certain that the KAT3 can handle 100 watts for a
lengthy
Guessing, but the audio setting would be found in MMTTY not N1MM.
Connect CODEC there and you should be good for AFSK.
GL,
Rick nk7i
On 9/22/2023 4:53 PM, Pete Smith N4ZR wrote:
For the first time in maybe 6 years I thought I'd spend a little time
in the CQWW RTTY contest this weekend. I
ON the roof will work (better) for you (install on a week
day while everyone is at work/school). The other issues include potent
RFI in the building (smoke detectors are great receivers, particularly
on 40M; GFCI devices are second best).
73,
Rick nk7i
On 7/29/2023 9:46 AM, Dr. William J. Schmidt wrote
will be happy to show you what you missed. (Antenna didn't fall over?
It's not big enough!).
73 Bill,
Rick nk7i
On 7/28/2023 3:36 PM, Dr. William J. Schmidt wrote:
I worked at Honeywell defense systems in the early 80's and I had two guys (Ph.D's from
MIT) working in the office next to me that were
and out. When you take a hit, that potential rises, equally if
all is done well; it's the difference in potential that harms.)
73,
Rick nk7i
On 7/28/2023 2:31 PM, Dr. William J. Schmidt wrote:
Even the methods in that book are considered sub-standard by the broadcast
industry... The only think
several reads to grasp what you
have to do.
73,
Rick NK7I
> On Jul 28, 2023, at 2:11 PM, j...@kk9a.com wrote:
>
> I would recommend that you follow proper lightning bonding/grounding
> techniques, these are the only methods that work. My tower has taken a
> number of lighti
to not be another (no matter the
mode).
73,
Rick NK7I
> On Jul 23, 2023, at 7:23 AM, M Cresap via Elecraft
> wrote:
>
> I have been running tests on K3s and K4s to understand the conditions
> needed to transmit clean FT8 signals. I have previously shared some of my
>
order (because
you’re loud and clean).
The choice is yours.
73,
Rick NK7I
> On Jul 20, 2023, at 7:33 PM, Pete Smith N4ZR wrote:
>
> OK guys - rather than reply individually, let me try to pull everything
> together in one message.
>
> In a previous effort at FT8 I fol
ned to be
used is enough, adding more just mungs things up.
So I suspect we actually agree.
73,
Rick NK7I
> On Jul 20, 2023, at 3:42 PM, Jim Brown wrote:
>
> On 7/20/2023 2:47 PM, Rick NK7I wrote:
>> s said MANY times, set the WSJT-X output to MAX, then IGNORE IT.
>
> Hi Ric
years the misinformation would fade out.
So now YOU know how to set the audio on the K3 and will be cleaner than those
who attempted to mislead you with false information.
This method holds true on ANY audio based digital mode (like AFSK, PSK…).
73,
Rick NK7I
> On Jul 20, 2023, at 2:17 PM, P
I politely and firmly, disagree. It's too prone to operator error and
sending cruft that doesn't belong on the air.
A SECOND internal card for radio, fine. The only one; bad plan.
Rick nk7i
On 2/24/2023 3:22 PM, Wes wrote:
There is nothing wrong with using the internal sound card
of
cruft sent, which helps no one.
If you're just starting out (and on occasion) ASK a neighbor to look at
your signal to make sure it's as you need it to be.
73,
Rick nk7i
__
Elecraft mailing list
Home: http://mailman.qth.net/mailma
The old CW traffic handler gag was "Having a great time. Wish you were
her(e)" with the final dit, missed.
73,
Rick nk7i
On 2/17/2023 12:50 PM, Dale Boresz wrote:
Unfortunately, there are a lot of missing spaces on the CW bands too.
73,
Dale - WA8SRA
On Fri, Feb 17, 2023 at 2:
It also won’t forward if the from address is the same as it is supposed to
forward to; so use a second account for testing.
73,
Rick NK7I
> On Jan 23, 2023, at 4:15 PM, Andrew Moore wrote:
>
> Note that many email clients can be configured with a custom "reply-to"
>
until the next reboot, negating it's value to less
than zero), again on ALL of your USB devices (hubs, ports etc).
73,
Rick nk7i
Use Windows Device Manager (run devmgmt.msc) to change the Advanced
properties of both of the K4 FTDI virtual serial ports: Uncheck Serial
Enumeration Check Disable
Have you tried putting the KAT500 into MAN mode (not bypass or AUTO)?
Once trained for bands (memory loaded), MAN is the best way to use the
tuner. It'll recall the tuning combination but won't go into auto-retune.
73,
Rick nk7i
On 11/14/2022 6:00 PM, Joe Rogers wrote:
I am operating
in cost
reaps major benefits (and aluminum is no longer legal for new
construction, at least when I retired).
73,
Rick nk7i
On 11/14/2022 2:25 PM, Fred Jensen wrote:
When my younger brother was finally out of the house for good, Mom and
Dad bought a double-wide, sold the house in So. Central
and be aware of the total house load/s, in particular
whatever shares the amp power circuit. Don't overload ANY of the circuits.
I think we can agree on that point. ;-)
73,
Rick nk7i
On 11/14/2022 9:36 AM, Jon Poland wrote:
I disagree with Rick. It is true that modern houses have more
electric
I'd move it up one tap as long as it does NOT EXCEED 85V at receive.
Higher voltage not only gives you better output but also cleaner. That
matters too.
73,
Rick nk7i
On 11/12/2022 10:25 AM, Gordon LaPoint wrote:
My KPA500 is showing 57-58 VDC at 450-500 watts out, and 71-72 VDC on rx
Yes. $60
Yamaha CM500 Closed-back Broadcast Headset with Boom Mic https://a.co/d/7c5F962
73,
Rick NK7I
> On Nov 1, 2022, at 9:56 PM, j...@kk9a.com wrote:
>
> Is the Yamaha CM500 still being manufactured?
>
> John KK9A
of the archives is recommended, this topic has been covered
many times before.
73,
Rick nk7i
On 11/1/2022 2:39 PM, Clark Macaulay wrote:
Hi, Bernie.
Like you, I am a CW op that dabbles in FT8. About a year ago I decided to
dabble in SSB just to hear an operator's voice in QSO parties and the like
AT those responsible.
Rick nk7i
On 10/8/2022 11:40 AM, David Gilbert wrote:
Wow.
On 10/8/2022 11:35 AM, Rick NK7I wrote:
You're whining, nothing more. It's unbecoming.
Pay attention to the lists; or not at your own risk.
Rick nk7i
On 10/8/2022 11:22 AM, David Gilbert wrote:
That's
You're whining, nothing more. It's unbecoming.
Pay attention to the lists; or not at your own risk.
Rick nk7i
On 10/8/2022 11:22 AM, David Gilbert wrote:
That's ridiculous. Any company that had your attitude would be out of
business. No way should anyone have to keep track of emails
this thread.
73,
Rick nk7i
On 10/8/2022 8:22 AM, Mike Smith VE9AA wrote:
Dave/AB7E seems to understand the point 100% correctly and a lot of you are
twisting my (and others) words.
The point is not that I don't have a microphone or that I couldn't cobble
together a connector for from
It would be in the archives.
Search for Eric, I'm pretty sure he was the one to write the post, no
clue what the header (topic) was. He's not a prolific writer (of email,
hi hi) so the search shouldn't take long.
73,
Rick NK7I
On 10/7/2022 6:53 PM, j...@kk9a.com wrote:
I guess I have
, like this one, now changed.
73,
Rick nk7i
On 10/7/2022 11:35 AM, j...@kk9a.com wrote:
The last update was 21 1/2 weeks ago:
http://mailman.qth.net/pipermail/elecraft/2022-May/289523.html According to
that post everyone in groups 1 through 4 should have received their product
by now. I am
). There is the occasional
errant user but they don't make contacts either, thankfully so they
don't hang out long.
73,
Rick NK7I
On 6/26/2022 12:26 PM, Bob McGraw wrote:
I operated FD from here at the house this weekend. Most all
).
73,
Rick NK7I
On 6/3/2022 9:22 PM, David F. Reed wrote:
I note my KPA1500 drops power at its temperature rises...
Using FT8, so a relatively high duty cycle.
Say I start at a heat sink temperature of 27 C, and 1,000 watts out;
by the time the temperature is at 65 C, the power has dropped
d.)
Which brings up one more point, ask someone knowledgeable nearby to
actually look at on their scope and listen to your signal; trust the
settings you chose, but verify they're working as intended.
Then operate exuberantly!
73,
Rick NK7I
On 5/6/2022 1:05 PM, rocke...@gmail.com wrote:
#1
the K4!
73,
Rick NK7I
On 5/2/2022 11:40 AM, David Gilbert wrote:
I still say it was purely a business decision WHEN THEY MADE IT. Yes,
some parts might be difficult to get now, but when Elecraft offered
the last chance buys they obviously expected to be able to source the
necessary parts
for a start up repair
shop; just like old car buffs and OLD radio folks manage to create. One
door closes, another opens.
73,
Rick NK7I
On 4/21/2022 12:11 PM, David Gilbert wrote:
I bought my K3 for two reasons ... its performance and its modularity
which promised long term support for upgrades
Print to (or download) the pdf version, then put that into a file space on your
Android.
73,
Rick NK7I
> On Mar 30, 2022, at 12:53 PM, Jim Brown wrote:
>
> On 3/30/2022 12:19 PM, Pete Smith N4ZR wrote:
>> I think a case can be made that when the K3 says its setting for
at 10 watts and consistently
worked (now I use a K4, KPA1500 and a much better antenna, no tuner needed).
If CW, was VOX on?
GL,
Rick NK7I
On 1/25/2022 2:21 PM, ncela...@scicable.com wrote:
I have a K3,KAT500 and KPA500. I had a station on 10 Meters this
afternoon that I wanted to reach
PS When using the tuner in the KPA1500 with the K3, it gets the 10
watts that I have as my default. I've not tested to see if that can be
changed to any other value.
I also attempted an ATU tune on the K3 into a dummy load, it's too fast
for power to be displayed. ;-)
73,
Rick NK7I
default, 10).
73, Merry Christmas,
Rick NK7I
On 12/8/2021 8:34 AM, Tom Boucher wrote:
*You can set TUN PWR in the K3 Config Menu to something other than 5
watts.73,DrewAF2Z*
Drew,
Page 60 of K3 Owner's Manual states: "TUN PWR Note 1: *TUN PWR* does not
pertain to *ATU TUNE, *which always u
Some folks, for esthetics usually, put chokes and resistors in only one
direction throughout the build, which may simplify finding mistakes later, the
numbers or color code direction is always the same.
Pretty is only relevant to the builder hi hi.
73,
Rick NK7I
Email spiel Czech
25 amp fusing isn’t a lot over overhead for a K3 with KRX3, KIO3a, P3 with the
SVGA board and the PR6-10 preamp in play.
It all adds up. Use what is appropriate for your rig combination.
73,
Rick NK7I
Email spiel Czech corruptions happen
> On Jul 21, 2021, at 10:33 PM, Ray wr
The
internet is a tool; it's not ham radio without a radio.
See you on HF!
73,
Rick NK7I
On 6/29/2021 5:51 PM, Michael Walker wrote:
Rick
I think you need to look at the average age of today's ham (hopefully,
it is going down).
Ham radio is what you make it. Your version is just fine for
dBm is my normal noise floor on most bands now; not the -80 I had before.
At the least, own a simple HT, KX#, to call yourself a ham in more than
license.
73 all,
Rick NK7I
On 6/29/2021 12:47 PM, Gordon LaPoint wrote:
I setup a remote about 10 miles from my house, with KT1I and WB8PKK,
becaus
as a Pi, just to play with. I said I like toys.
I have cameras too lol. More than one. Those same ‘rules’ apply.
73,
Rick NK7I
Email spiel Czech corruptions happen
> On Jun 28, 2021, at 6:09 PM, Dick wrote:
>
>
> I will never understand how those in the Amateur radio hob
; some are free. Some are just crap-ware...
It's a struggle; just fill your needs.
73,
Rick NK7I (specifically NOT saying which one I use)
On 6/28/2021 2:54 PM, jerry wrote:
So what's the hot ticket nowadays on logging software?
I rolled my own, but it's
quite primitive. It runs on my Linux
have my K4 yet, so it's a guess.
73,
Rick NK7I
On 6/18/2021 11:58 AM, Jim Brown wrote:
On 6/18/2021 11:34 AM, Ed Cole wrote:
I wear hearing aids and the CM500 immediately set up a loud howl the
minute I put them on (even with not being plugged into the radio).
Apparently my hearing aid gain
.
Sorry for your loss,
Rick NK7I
On 3/29/2021 10:30 AM, John Simmons wrote:
Dave,
This topic was recently covered either here or another reflector I
subscribe to.
There isn't a very good way to properly find all the options installed
other than pulling the cover to see. There are two programs
to another radio, it still works too). WSJT-X
can also load directly into the logging program of HRD (if you use for
example Win3K3 for rig control with HRD logging). They all play nicely
together.
73,
Rick NK7I
On 3/22/2021 9:21 AM, Bill Frantz wrote:
Welcome to the list and to the K3.
I had
) for a better
understanding.
73,
Rick NK7I
On 3/19/2021 2:06 PM, Robert G Strickland via Elecraft wrote:
It seems that there are two ways of running grounding wires in the
shack: FAN - from a common ground point, individual grounding wires
are run to each piece of equipment; LINKING - a ground wire
on the K4 audio. Two less wires on the
desk, foot switch to transmit...
73,
Rick NK7I
PS if not, can it be one for the want list?
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http
My bad, I didn't think it through enough. Joe is right.
Rick NK7I
On 1/4/2021 1:10 PM, Joe Subich, W4TV wrote:
I recently purchased a P3 and connected it to my K3. The
installation shares the RS232 connection with a Microham USB
interface III for digital operation. I used a Y cable
While I don't have the Microham, the Y should be first in the series
(listen only port to the Microham); to the P3, then the cable from the
P3 to the K3 so they can 'chat'. (That is the same as I do for my
SteppIR controller.)
HNY,
Rick NK7I
On 1/4/2021 12:28 PM, MICHAEL SMITH wrote
.
By then the support staff at Elecraft should be back on duty for further
comments and testing.
It's curious (disturbing) that both of yours exhibit the same issues
(though one is 'better').
Good luck, please report back any useful comments or fixes.
HNY,
Rick NK7I
On 1/1/2021 10:34 AM, g4piq--- via
You've made a mistake, a long XMIT (TUN) press is for applying a small
amount of output, to match with the antenna (or check the SWR).
ATU TUN (ATU) applies power to the internal tuner, if any, if enabled.
Two different functions.
73,
Rick NK7I
On 12/4/2020 10:06 AM, Joseph McIntire wrote
) bring this up monthly anymore; the answer in the foreseeable
future, is no. For excellent reasons.
Most of the users buy in because of the well proven quality and won’t accept
substitutes. Stop asking.
73,
Rick NK7I
Email spiel Czech corruptions happen
> On Nov 25, 2020, at 10:10 PM,
. Plus you can talk to a tech (except for COVID delays
now) the same day you initiate contact.
73,
Rick NK7I
On 11/25/2020 8:25 AM, Andy Durbin wrote:
"Name any other company that gives you FREE firmware updates in real time (not
months later like Icom or never like most others) until the i
Fake It keeps the tones between 1500-2000 Hz. (not 1000) so that the
harmonic energy is out of the passband.
Also the response of the sound card has some variation at different
pitches (it's not a totally flat response), so try different tones.
73,
Rick NK7I
On 10/21/2020 6:19 AM, Dave
this year.
CA has exceeded the 4 million acre threshold (30+ dead); a record that no one
wants... with another month (or more) of fire season to go (in the north, the
south never closes).
Prayers for all the impacted; the level of destruction is beyond traumatic.
Rick NK7I
Email spiel Czech
Using that same page, it shows m provider (barely) provides IPv4 with no IPv6.
My mantra is still “I didn’t move here for the Internet”. ;-)
Rick NK7I
Sent from my iPad
> On Sep 27, 2020, at 11:54 PM, Bob Wilson, N6TV wrote:
>
> Using a web browser on Windows, on the same LAN
Your router may supply it to your lan, but your provider may not utilize
it yet.
Rick NK7I
On 9/27/2020 11:41 PM, Bob Wilson, N6TV wrote:
I'm not sure what you mean by "support IPv6".
From a Windows command prompt, I tried a *ping -6* command with the radio's
IPv6 address, to
Occasionally the filters, shift center, NR or NV kick in and I've always
written that off as random output from the computer. A filter reset
(long push on the shift knob) or a mode change usually brings it back to
what is wanted.
73,
Rick NK7I
On 9/21/2020 1:49 PM, David Gilbert wrote
safe,
Rick NK7I
On 9/10/2020 6:28 PM, Wayne Burdick wrote:
I thought I'd post an update given the many questions on this topic. I'm the
bottleneck on documentation, something that wasn't supposed to happen,
but...stuff happened. No need to rehash that.
There are three major documents
If you model it accurately, you see that a 4:1 transformer will cause most
(other than 160M) to have a closer match; while on a few the 1:1 device will
work better.
If convenient, try each. They each offer (dis)advantages.
Rick NK7I
Email spiel Czech corruptions happen
> On Sep 1, 2
...
*IF* you have a newer vehicle that measures current draw and charging
rate at the battery (sometimes via the negative pole), you'll want to
use that sensor point for negative connection; not at the battery.
That's the super quick description, to start a foundation of proper set up.
73,
Rick
ket'.
73,
Rick NK7I
PS I watched after, those days were already filled with family things.
Being able to see what I wanted on my own schedule, really nice.
On 8/22/2020 2:53 PM, Gary Peterson wrote:
Agreed. Much better than I expected. And I never considered attending a
hamfes
forget to add a common mode current choke at the feed.
73,
Rick NK7I
On 7/26/2020 11:57 AM, Don Wilhelm wrote:
Fred,
That would be correct if they are oriented at 180 degrees from each
other so as to cancel the horizontal radiation. Elevated radials must
be tuned to be effective, but only 2
to
output.
73,
Rick NK7I
Email spiel Czech corruptions happen
> On Jul 17, 2020, at 7:00 PM, Fred Jensen wrote:
>
> No antenna has, at any time, anywhere in any of our lifetimes, been "tuned"
> by an "antenna tuner." So called antenna tuners are 2-por
. ;-)
If split, use the same observations, but turn off XIT and use the other
VFO for TX (allowing you to hear the station being worked as well).
EVERY operator has a pattern, humans are just wired for consistency.
Find it, predict it, make that contact.
73,
Rick NK7I dit dit
On 7/16/2020 9:27 PM
at product and
service; they understand much better than the other brands.
No one has a guarantee to tomorrow, but there are signs of hope around.
73,
Rick NK7I
"It ain't the years darlin', it's the miles!" Indiana Jones
On 7/16/2020 12:13 PM, rich hurd WC3T wrote:
Climb safely.
Th
the conditions they
face. And doing it well, the Elecraft way. This'll take a while so
patience is required.
If you truly feel deceived, cancel your order and let the next in line
move up a slot. I'm sure they be appreciative.
Rick NK7I
Another CA escapee and I don't miss it for a moment
You’ve just defined the vast majority of DX (and DXpedition in particular)
contacts.
That doesn’t make less a part of ham radio.
Rick NK7I
Email spiel Czech corruptions happen
> On Jul 12, 2020, at 4:54 PM, Lynn W. Taylor, WB6UUT
> wrote:
>
> ... but if all you're doin
ike hungry
Mongo... band slots, while tasty, do not make a meal.
73,
Rick NK7I
On 7/8/2020 5:08 PM, Eric Norris wrote:
Actually, I have, Rick. The KPA1500 is the second greatest amplifier
in the history of the solar system. It's a BattleBot, a monster, the
doomsday legal-limit
Lyn,
You can try restarting the utility; sometimes if you push the front
buttons (power on/off, standby), the app gets out of sync for the KPA500.
73,
Rick NK7I
On 6/23/2020 4:50 PM, Lyn Norstad wrote:
Nope. "Should be" is not how it works. I have discussed this wi
to 50 ohms). The worse the unmatched condition, the more useless the
display becomes. It wants to see 50 ohm in, 50 ohm out to provide
accurate power readings.
So if your antennas demand a matching circuit (tuner), the LP sensor
becomes less valued at the output of the amp.
73,
Rick NK7I
attention.
They can't assemble from parts they can't get; they can't sell without
assembly. What more do you expect of them?
Rick NK7I
On 5/15/2020 1:40 PM, Tom Doligalski via Elecraft wrote:
All I have asked is honest information. Sad that Elecraft fails to respond to
customers, especially
the same things with little
to no whining.
I suggest a socially distant walk in the sunlight (which kills the virus
AND calms the spirit); repeat often.
Try to have a better day,
Rick NK7I
On 5/15/2020 11:54 AM, David Gilbert wrote:
Don't put words in my mouth ... I never said anything about lies
t; because "Stuff" happens. ;-P
Rick NK7I
On 5/15/2020 11:13 AM, David Gilbert wrote:
All of that is true, except that it doesn't take somebody like Wayne
or Eric or any of their engineers to draft a weekly status report to
those who have put down a deposit. Anybody who speaks
That implies that the AUX cable is not working. Cycle the gear power
and make sure each connector is properly seated.
Rick NK7I
On 5/15/2020 11:07 AM, Edward via Elecraft wrote:
I have the combo K3S/KAT500/KPA500 with all of the optional interconnection
cables.
I am not able to key
of us.
Rick NK7I
On 5/15/2020 10:22 AM, Tom Doligalski via Elecraft wrote:
I agree, but am quite disappointed about the lack of direct communication from
Elecraft with folks who have put money down. I haven’t heard directly from
anyone at Elecraft since January 16 (and that after my instigation
If it were NOT a contest, there would be NO reason to post standings in
the QST magazine because 'points' would have no meaning.
Rick NK7I
On 5/14/2020 11:17 AM, Bob McGraw K4TAX wrote:
From ARRL - At its core, Field Day is a local event and an opportunity for
local amateur radio clubs
Kenwood, 8 pin round but use the K3/S menu to turn the 'button' feature off.
Rick NK7I
On 5/13/2020 11:53 AM, Jim Brown wrote:
On 5/13/2020 11:43 AM, Edward via Elecraft wrote:
I plugged in an Icom mic.
The three JA mfrs use the same mic connector but different pin
connections, making
Simpler yet, use an appropriate size (for your desk) tablet to manage the K4.
Then take that with you when you’re in another room, traveling, etc.
Rick NK7I
Smell Czech corruptions are inevitable
> On Apr 19, 2020, at 1:11 PM, hawley, charles j jr
> wrote:
>
> When
.
With my quiet environment I base my output power on the signal I receive, if
loud, low output; if weak, ramp it up.
Rick NK7I
Smell Czech corruptions are inevitable
> On Apr 5, 2020, at 6:09 AM, brianchapn...@rogers.com wrote:
>
> My only rig is a kx3 so I have no experience at h
Because it’s weak signal at the receiving end; you use what power it takes to
succeed in making the contact, up to the legal limit.
On 160M, 1500 watts out is common.
Rick NK7I
Smell Czech corruptions are inevitable
> On Apr 4, 2020, at 9:02 PM, brianchapnick wrote:
>
> This d
and Flex are among the cleanest, sheer cliff walls of audio.
Rick NK7I
Small phone keyboard, smell Czech corruptions are inevitable
> On Mar 29, 2020, at 10:48 AM, Dauer, Edward wrote:
>
> Previous posts suggest a consensus, or at least a widely-held opinion, that
> the K3 is below pa
, with the amp on, with
just the tuning energy and if ok (medium power out of the amp), then raise to
the desired level of output for a ‘final’ test. At least until the tuner has
been programmed for all bins in each band.
Using resonant antennas is SO much simpler.
Rick NK7I
Smell Czech
1 - 100 of 101 matches
Mail list logo