add it later so as not to have to remove the front panel.
Does this make sense?
...bc nr4c
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft
Hi,
For information purposes I'd like to annouce I fixed my rattle. I
built my K3 about 2 weeks ago, and had a rattle caused by the large,
thick spacer washer on the phone jack. Well, I tried tightening it
but still no joy.
This week, I installed the Digital Voice Recorder and therefore
The discussion below is one approach, but not the situation I am
dealing with. I am looking for a way to access the signal from the K3
that tells the ATU to TUNE. I want to use the front panel ATU button
to start the TUNE process, not a button on the tuner. Leaving the
tuner in AUTO
Where is the 4.1 beta? I have looked for it and onbly founbd the 4.05
which i already hve on my K3.
...bc
Quoting David Pratt da...@g4dmp.fsnet.co.uk:
Joe - It might be useful to upgrade to the latest K3 v4.10 beta
software. It provides some changes to the way the transverters are
A mode, it had shifted a lot to
the left, maybe 1khz. What gives?
...bc nr4c
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
don't want to damage the radio, but
don't want to start off with a weak signal if I can do better.
Thanks
...bc nr4c
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
I'm not sure if this will work for you, but I did accomplish writing a
couple of macros last night that will switch the mic from front to
rear and update the tX EQ accordingly. now i can have both my headset
and hand mic avail at the press/hold of a front panel button. this
might work
that the recordings contained
some TX EQ AND I was hearing it compounded by the current TX EQ for
the front mic.
Does this make any sense.
Help!
...bc nr4c
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help
Alan,
Thanks for the answer to my question. That would be a simple accessory.
Now to answer your question. A lot depends on how your station is
setup. If the radio is placed so it is very inconvienient to
disconnect the cable, it makes sense to add a switch. And, there may
be times
I use my CM500 on 'RP.L bias' with mic gain set to around 12-15 and
compression less than 20. I get good audio, and good power out. it
just plugs right in the real panel jacks. My TX EQ is set to -16 -16
-16 +3 0 0 0 0 (I think this is right).
Could you explain why you are going thru a
.
..nr4c
Quoting JAMES ROGERS w4...@bellsouth.net:
In a word, yes
Jim, W4ATK
On Nov 4, 2010, at 12:18 PM, Nate Bargmann wrote:
I updated my K3 to MCU 4.17 beta last night along with DSP 2.65 and
FPU
1.4(?) and now today I notice that my SSB output is down about 3
dB. I
can only coax
answer to this.
...bc
ps; Hi Roy!
NR4C
Quoting Jim Cox jcox...@bellsouth.net:
Yes, this has been a problem here since I got my K3 about a year ago.
Others have noticed it when their audio is played back to them making
playback on the air almost useless for quality reports.
I have reported
with TX EQ flat at 0 0 0 0 0
0 0.
...bc NR4C
Quoting David Gilbert xda...@cis-broadband.com:
A quick and easy search of the archives brought up this reply from Lyle
dated June 22 to an earlier post:
The DSP treats all TX audio sources the same: FP MIC, RP MIC, Line In,
and DVR. TX EQ
We have a gov net that we check into weekly at the EOC here at our
installation. It uses frequencies assigned by the NTIA and are near,
but slightly below or above the ham bands. Can the K3 be modified to
transmit on these frequencies? How?
William Conkling
Alternate Spectrum Manager
buy the base model, and
are going to do a lot of upgrades, any chance of a 'Zipper' or Velcro
fastener on the top panel?
Ok, One more question, Do we get any pretzels or peanuts with the Kool-Aid?
.
K3 4536 proud owner (P3 841)
...bc nr4c
Quoting k2qi@gmail.com:
Hi Mark,
That connector (looks like an RJ11) is an accessory connector that
isn't used for anything at the moment. Perhaps the guys at Aptos use
it for diagnostics?
James K2QI
That connector
--Original Message--
From: Mark Goecke
Sender:
Quoting k2qi@gmail.com:
Hi Mark,
That connector (looks like an RJ11) is an accessory connector that
isn't used for anything at the moment. Perhaps the guys at Aptos use
it for diagnostics?
James K2QI
That connector
--Original Message--
From: Mark Goecke
Sender:
It's a 6 lead version of the modular connector. There is one on the P3
front panel as well. I think it might be a test port for the panel
assembly.
sure would be nice for a mic or a separate panel to use fo mobile
installation.
,,,bc nr4c
Quoting k2qi@gmail.com:
Hi Mark
nr4c
Quoting The Smiths notforc...@hotmail.com:
I'm sorry, perhaps I'm mistaken, but I've already hooked up my K3
using a serial to USB converter cable, and then turned on
Spectrogram and found that the audio IS already there. Do I have a
voodoo K3, or is someone else mistaken
, you MUST
cycle the K3 power to make it appear.
...bc nr4c
Quoting Bill K9YEQ k9...@live.com:
If you press and hold the tune button it will cycle on and off. Try holding
it down once to enable it.
Bill
K9YEQ
-Original Message-
From: elecraft-boun...@mailman.qth.net
this out soon with some on air recordings from friends.
OK, who's got the Kool-Aid pitcher? Where are the nuts and pretzels?
...bc nr4c
Quoting Nate Bargmann n...@n0nb.us:
Before I start I should note that I'm not a top tier contester. For
that matter I probably don't even rank very high
Yes. You have PTT or KEY(CW) configured wrong. maybe try to start N1MM
without the K3 on. Find these settings and verify the configuration.
Also check your cabling. Might try unplugging all cables and
re-connecting one by one.
Divide and Conquer.
...bc nr4c
Quoting dbellw...@aol.com
is the
best in the industry.
...bc nr4c
Quoting VK7JB zen...@netspace.net.au:
Hello group,
My mouse is hovering over the Add to Cart button for a K3/100 modular kit.
I'd really value some candid advice about options before I commit.
My situation: I'm a casual operator, data modes, SSB
Yes. The K3 is very much like a computer and when you press the OFF
switch, you initiate a 'shutdown' procedure that eventually turns off
the power. All of your settings get saved to memory so that it will
start-up next time just the way it was when it was shutdown.
...bc nr4c
Quoting
want at a later time.
This is the beggining of a great adventure.
...bc nr4c
Quoting VK7JB zen...@netspace.net.au:
Hello All,
A couple of people have asked me to post a summary to share what I learnt
from my question about options for a new K3. I received 25 replies, many
were off-list
be transintted 100% of the time. The other tone is a pulsed
deviation from the base, so is only ON for short pulses when needed
to form a character. Since there is hardly ever an even distribution
of MARK/SPACE, the power out will not be the same.
My $.015 worth.
...bcnr4c
Quoting Mark n2qt n
gain to be set pretty low (prob less then 20) and
adjust comp to get about 10db on the COMP scale. I'm trying to
remember, but I think I have the TX EQ set to -16 -16 -16 0 0 0 0 0.
My widest filter is 2.8KHz so I haven't tried AM or FM so far.
...bc nr4c
Quoting Jim Sheldon w...@cox.net
any chance of recording the CW audio on a DVR and replaying and
recording into one of the memories with the K3 DVR? then jkust play
it back on the air.
...bill nr4c
Quoting Richard Ferch ve3...@storm.ca:
Scott,
If Ralph's guess is correct, there is a configuration option to do
will not be). Unless you need the sound card for computer sounds
and/or other audio uses, I'd just use the computer sound card. PTT can
be handled via the serial CAT cable.
bill nr4c
On Thu, 03 May 2012 07:32:45 -0400, Steve wrote:
Good Morning All,
I have a K3 and am awaiting my KX3
I seem to remember that one issue with Scott's programs is that he
sends the 'MODE' command before the band/freq. And, depending on your
settup, the freq re-sets the MODE.
Anyone able to comment on this?
..bill nr4c
I know it seems daunting, but a call to Astron might change your mind.
A few caps and I have heard that the transformers aren't that expensive
($50)so you might re-think a refresh.
...bill nr4c
On Tue, 12 Jun 2012 10:21:23 -0400, Bill wrote:
Transformer let go - not worth fixing. I'll just
that way.
My $0.02 worth
...bill nr4c
On Wed, 20 Jun 2012 06:16:29 -0700, eric manning wrote:
Rich said:
intelligibility is concentrated around 1-2K Hz. Yes?
I think so. If my failing memory serves, early Bell Labs work found
that
300 - 3000 Hz was the minimum- width audio band
enjoying mine.
...bill nr4c
On Tue, 26 Jun 2012 00:20:12 -0800, Edward R. Cole wrote:
I believe this has been asked before:
Is the K3 Utility usable with the KX3; is the k3 memory editor usable
with the KX3?
73, Ed - KL7UW, WD2XSH/45
==
BP40IQ 500 KHz
cabling, Antenna, settings. Oh, how is your
RF/AF gain controls set up. I have separate RF gains, but the AF gains
are set up so that the little knob is volume, and the larger one is a
fader. How are your set up?
./...bill nr4c
On Sun, 01 Jul 2012 22:49:36 -0600, W0MU Mike Fatchett wrote
, but I'm really leaning
toward using magnets to provide the 'feel'. I've done this with others
including a AZQRP Scorpion.
...bill nr4c
On Mon, 2 Jul 2012 07:51:49 -0700, Sid Leben wrote:
I received my KX3 a few days ago we are getting acquainted.
Similar to my K3, but not the same..
I
nr4c
On Wed, 04 Jul 2012 22:59:52 -0500, David F. Reed wrote:
I must be doing something wrong, but I can't seem to use my Proset-K2
with my KX3...
The headphones work fine, but plugging the microphone into the mic
input
puts the KX3 into transmit mode; I had expected to use the XMIT
button
not an issue in my shack. YMMV.
Hope this helps, good luck!
...bill nr4c
On Thu, 5 Jul 2012 10:55:35 -0500, Terry Schieler wrote:
I have a SignaLink USB external soundcard that I have used
successfully for years with my former rig (FT1000MP). Got around to
hooking it up to the K3 (#474) a couple weeks
another
laptop. Don't give up!
...bill nr4c
On Tue, 17 Jul 2012 11:43:33 -0700 (PDT), W8JH wrote:
My K3 has lost communication with the K3 utility program. Although
properly
configured (comm port) the Utility cannot read the versions of
firmware in
the rig nor update them. The recent
Sounds like you have somehow mis-configgured your filter(s).
Try using the K3 Utility and verify your filter settings. Make sure
you have selected the 2.7 KHz filter for SSB TX. Can we assume you have
a 400 hz filter installed for CW?
...bill nr4c
On Mon, 23 Jul 2012 05:33:20 -0700 (PDT
What Elecraft Keyboard?
...bill nr4c
On Thu, 2 Aug 2012 07:35:30 -0500, W4ATK wrote:
Has anyone tried the MFJ-551 RFI suppressed keyboard? This is a PS2
type of keyboard but PS2/USB adapters are cheap. Better yet, any word
on when the Elecraft keyboard will be available?
Jim, W4ATK
Anyone have any experience with the Behringer U202 or U222 USB sound
device? I see a lot of regular spikes across the band.
...bill nr4c
On Thu, 2 Aug 2012 08:46:14 -0500, Tony Estep wrote:
On Wed, Aug 1, 2012 at 9:40 PM, Buck k4ia k...@aol.com wrote:
...the signals are not there - just
and potential customers is not in good taste. It there
were a systemic problem with support or service, the company would not
be doing business this long with the vast array of products available
that Elecraft offers.
...bilkl nr4c
On Tue, 7 Aug 2012 07:17:41 -0400, Robert Emory wrote
Yes, the SignalLink USB is a mono sounbd card with other features, a
very nice, reasonably quiet mono soundcard.
...bill nr4c
On Tue, 21 Aug 2012 05:53:47 -0700, Jeff Herr wrote:
Is signalink mono?
__
Elecraft mailing list
mating of the connectors. I have seen a device that looks like a
'chain' locking link than can be used to hold a connector set together,
but I think the hole in the K3 connector is obscured by the case panels.
...bill nr4c
On Mon, 3 Dec 2012 06:14:01 -0800, Ron Midwin wrote:
I was working cw
.
bill nr4c
On Mon, 03 Dec 2012 06:49:11 -0800, Bob W7AVK wrote:
Gang - Know I should have it somewhere but I can't find the
instructions on using APF. Someone please refresh my memory. I
have
the latest K3 software loaded.
73 Bob W7AVK
K3/100K s/n 4365
visualization tool. This worked pretty well.
Funny thing, my 200Hz fileter with a -86Hz offset is pretty well
centered about the centerline, but my 400 Hz 8-pole with 0 offset, is
way off center! So are the 1.8 and 2.8 filters. What gives?
...bc nr4c
Quoting Amateur Radio Operator N5GE n
being duplicated.
...bill nr4c
Quoting N1IRB n1...@cox.net:
I am getting ready to add the second RX to my K3. I notice that the order
page says that only one AM and FM filter is required in my radio for the TX
side. So my question is when using the divirsity mode to listen to say
It should work fine. I replace my TS570 with a K3 and used the same
serial cable.
...bill nr4c
Quoting Adriano adriano.pera...@uol.com.br:
Anyone knows if the Serial to Serial cable from FT-2000 would work w/ the k3?
Tnx again
PY2ADR
K3 4795
OK, yes, My TS-570 has a gender changer mounted on it's rear RS232
port. My main response was to the fact that the wiring is the same,
and I didn't consider gender. However, the cable I used for the 570
is the same cable I use for the K3, minus the gender changer.
...bc nr4c
Quoting
tube and made a screen out of brass screen. Find a foam wind screen
and a wooden plug in the other end with a hole for the cable to exit
and a plug on the end.
I'm not aware of anyone making a desk mic stand with PTT other than Heil.
This should get you started.
...bill nr4c
Quoting Phil
enjoy your K3 as much as I've enjoyed mine.
Good luck
,.,.,bill nr4c
On Sun, 20 Mar 2011 21:49:54 -0700, Kate Hutton wrote:
My new K3 works great on CW - love the way it sounds the
intuitively
logical controls - but I'm trying to figure out what part I need if
any to
connect my
From the owner's manual for the K3, the DC power output is rated at
0.5A max. The P3 max draw is, you guessed it, 0.5 A max. this doesn't
leave a lot of overhead for 'all' the other things you want to power
with it.
...bill nr4c
On Tue, 3 May 2011 01:43:09 -0700, Fred Townsend
receiver. I do, and can work around the
issue
I have used software that allows independent selection of RX and TX
frequencies, within the audio bandwidth. Left-click for RX, right-click
for TX. Most notable is Hamscope, but I have seen others.
...bill nr4c
this way. I can also work
. They'll send you a new chip to insert in the tuner.
I hope this helps.
...bill nr4c
BTW: if this doesn't help, loan me the KPA500 for a while, you know,
maybe until thge Elecraft tuner makes it's appearance.
On Sun, 15 May 2011 11:00:57 -0400, Nels Anderson wrote:
Been enjoying KPA500 #32
it would be in there was some way that the mic's could
be active during 'non' key periods so that the logger and operator could
talk to each other to verify calls, exchange etc. and still hear what's
on the radio.
Is there any chance this might be added to the K3 feature list?
...bill NR4C
/MRP40-EN/IF.gif, the part with the
opto-couplers. A patch cord from computer OUT to K3 LINE IN Will get
you the audio. The K3 already has transformer isolated in/out on the
LINE interface.
bc nr4c
On Tue, 24 May 2011 09:34:11 +0100, Gavin Keegan wrote:
I would like to use the MRP40
suffering, but not dangerous.
...bill nr4c
On Tue, 24 May 2011 16:00:49 +0200, jgaudron wrote:
Hello
(On behalf of a friend, Gerard, familiar with his K3, but not so much
with
the English language )
When he sets the power of his K3 at 110, 100, or 90 watts, it
decreases
gradually down to 50
Thanks for this note. I had completely forgotten this capability. I
have to use a second RS-232 port for keying my rig due to software
restraints (N3FJP won't use same serial port for CW as CAT).
...bc nr4c
On Tue, 24 May 2011 15:24:25 +0100, Brendan Minish wrote:
The requisite keying
Sounds to me like they are providing a serial cable (one end, DB-9 to
fit computer and the other end a diferent connector to fit KX3 but not a
DB-9 die to limited space).
...bill nr4c
On Fri, 27 May 2011 09:00:38 -0700 (PDT), Lee Buller wrote:
What does this mean and how does this work
I've wired several K3, Kenwood and ICOM mics and Kenwood and K3 are
very similar. I think you'll find that the mic and PTT are the same,
with mic being on Pin 1 and 7, PTT on 2 and 8. Cable shield is usually
tied to pin 8 as well.
...bill nr4c
On Thu, 2 Jun 2011 06:04:55 -0700 (PDT
) and in data mode, the Mic gain control varies LINE IN
level. From here, a little testing with a dummy load for TX and some
tweaking on the rec end should get you going.
...bill nr4c
On Thu, 9 Jun 2011 10:03:45 -0700 (GMT-07:00), Don Putnick wrote:
Hi all,
I'm the proud new papa of Elecraft K3
separately and the data combined after decoding.
73,
... Joe, W4TV
On 6/15/2011 10:39 PM, Bill Conkling wrote:
The K3 line out jack is MONO. Nothing beyond the K3 is gonna see
two
signals. It might be combined in the K3 audio circuit, I didn't
look this
up.
...bc nr4c
and the KEYOUT.
...bill nr4c
On Tue, 10 Jan 2012 10:56:41 -0500, Ian Kahn wrote:
All,
I recently acquired a used Ameritron AL-811H for use with my K3
(until I
can save enough to get the KPA500). I seem to be having issue
getting the
amp to respond to key down on the rig. I have an RCA cable
hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
DUH! been there, got the Tee shirt!
...bill nr4c
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http
Since you can access the M1-M4 buttons for 'playback' from N1MM for CW
messages, I assume it (N1MM) could playback the M1-M4 DVR messages as
well. I think it just sends the EPL macro as ascii text over the serial
line.
...bill nr4c
On Mon, 23 Jan 2012 14:19:01 +, Mike Clarke wrote
On the P3 there is a menu function to calibrate the frequency. Do this
and you can set it perfectly.
...bc
On Tue, 24 Jan 2012 07:07:52 -0800 (PST), N0SA wrote:
I have a K3 with the P3 panadapter.
When I properly tune a CW signal in and us the SPOT and CW indicator
I
notice that it is not
be relevant to your situation.
For me, the jury is still out on the continued use of the WinkeyUSB.
It works well for keying, but..
...bill nr4c
On Mon, 30 Jan 2012 15:54:28 +0100, Arie Kleingeld PA3A wrote:
As said, N1MM can key the K3 via the serial port.
Still, I use my old K1EL keyer because
Not real sure what you question is, but
If using n1mm logging software, it is possible to have n1mm send
message to the K3 to play one of the m1-m4 memories pre-recorded via the
DVR for call and/or contest exchange. Works very well.
...bill nr4c
On Mon, 30 Jan 2012 11:14:00 -0600 (GMT
else gets unceremoniously unplugged.
Good luck, but don't jump the a quick fix, make sure you're fixing the
correct problem.
...bill nr4c
On Tue, 31 Jan 2012 13:56:16 -0500, Linda and Bob wrote:
Rick,
I just checked the rear panel at the paddle jack area. There is no
external lock washer
I think they meant the 'OTHER' end of February.. You know, closer
to March.
...bill nr4c
On Wed, 8 Feb 2012 11:33:36 -0800, Keith Heimbold wrote:
Just curious is there any word on when the first KX3 transceivers
will ship. It is February now and I am getting very excited.
Keith
That's odd, as yours is newer than mine, and I'm pretty sure mine has
gold plated pins on all connectors. And, my K3 was delivered Aug3,
2010. Well after the 2009 date.
...bill nr4c
On Tue, 14 Feb 2012 14:37:36 -0200, Adriano Perazio wrote:
Mine is s/n 4795 and showed this problem last
Try downloading the manual for the amp from the Elecraft website manual
download page. Should show you everything you need to know.
...bc
On Tue, 14 Feb 2012 12:17:05 -0500, Francisco Siso Hennessey-HK3W-
wrote:
Last friday I bougt a KPA500 and is on the way right now, I want to
know
, set the first three TX EQ steps (50,
100, 200) to -16, all others at +0 and you will sound good. A bit of
tweeking here will make you sound great!
...bill nr4c
On Mon, 20 Feb 2012 21:50:09 -0700, Bryon wrote:
Hello everyone. I have a couple questions for you. I have browsed the
archives
of hte radio. Works well, and cheap.
...bill nr4c
On Wed, 22 Feb 2012 09:44:29 -0700, W7RIV wrote:
I have a K3 and I'm looking for inexpensive suggestions for desk mic.
Thanks,
- -
73 de Bryon/W7RIV
http://www.w7riv.com
I would leave them alone. I don't think mine are 'straight' but it
works.
bill nr4c
On Wed, 22 Feb 2012 11:35:39 -0600, Joel Black wrote:
I came home for lunch today and my KAT3 was in the mailbox. I opened
the box and the zip-lock bag and was looking at it through the
anti-static bag
I recommend the Elecraft site for manual for the BL1 or BL2 BALUNs they
sell. Or just buy one of them. The BL2 is switchable from 1:1 to 4:1
and is small, and very well designed. I tested mine on a high end
vector analyzer and it is flat from 160-6meters and beyond. Handles my
K3/100 and
The headphone jack is not the issue, it was the SPEAKER jack.
Different amplifiers. I haven't seen a mono plug on a headphones set in
a long time.
bill nr4c
On Sun, 26 Feb 2012 08:42:32 -0800, Phil Hystad wrote:
Back around the time I got my K3 (serial number #3799) there were
arrives and I get to tryit out with antennas that I already have
before i look further.
Good luck,
...bill nr4c
On Mon, 5 Mar 2012 15:01:39 -0500, John Stears wrote:
Good afternoon, I am a very new (receive only/studying for license)
enthusiast caught up in the excitement here and for the loaded
' will be dealt with a lot better in a future formware
release after the P3SVGA card ships so keep watch.
...bill nr4c
On Tue, 6 Mar 2012 17:45:57 -0600, David F. Reed wrote:
I am wonder if it is possible to look at your transmitted signal with
the P3; I only see the receive side. If so, how
won't ever get this
thing delivered.
...bill nr4c
On Wed, 7 Mar 2012 16:12:47 +, va3...@gmail.com wrote:
In one of the previous notes from Wyne, he mentions that maybe
Elecraft would end buying a bulk, good quality set of plugs that can
be ordered (instead of talking one's chances by order
newer than what? Version 1.11 is available, adds support for P3SVGA
adapter among other mods.
bill nr4c
On Sun, 11 Mar 2012 18:46:53 -0700 (PDT), John_N1JM wrote:
Any new P3 firmware version in the works?
John N1JM
--
View this message in context:
http://elecraft.365791.n2
For what mic? Any chance of getting a different cable?
...bill nr4c
On Sun, 11 Mar 2012 20:58:00 -0500, John Shadle wrote:
Hi all,
Are there any recommended 8-pin to stereo mic cables for the K3 (for
moving the mic to the rear panel), or will just any old one do?
Thanks!
-john W4PAH
screws of the K3, and illuminates the front panel for operations
like Field Day after dark.
...bill nr4c
On Tue, 13 Mar 2012 07:06:23 -0700 (PDT), Mike K2MK wrote:
Hi Bill,
Thanks for the information. I haven't received my shipping notice yet
but
I'd thought I'd get prepared. I found a 12V
like my K3 for my day to day
DXing and contesting. I would not like to have to make the choice of
one OR the other.
...bill nr4c
On Tue, 13 Mar 2012 13:33:27 -0400, David Stratton wrote:
This question has been going around in my head
and I would like some feedback from Elecraft owners
. This eleminates the coax jumper altogether. I would
think it would be a very low loss way to go. My only concern is that
the whole thing gets pretty long and bulky hanging off the KX3. Prob not
as much an issue with a K3/K2 radio. What do you think?
...bill nr4c
On Mon, 2 Apr 2012 09:13
in ham radio than money spent on wire, rope and
feedline for an antenna. The five most important items in putting out a
signal are: ANTENNA, ANTENNA, ANTENNA, POWER, MODULATION!
Congratulatios on you upgrade, and best wishes on you exciting
adventure with HF radio.
...bill nr4c
On Mon, Apr 2
There's a lot of empty volume in the P3 already. maybe somneone could
build a PS in the same enclcosure as the P3.
...bill nr4c
On Thu, 30 Jun 2011 21:37:02 -0400, Andrew Moore wrote:
On a related note, since it's been a long time since I asked, is
there a
possibility of offering a bare
I seem to remermber that Prolific has a driver Remover on their
website. Try google PL2303REMOVER. But, first try to use
Windows/CONTROL PANE/Add_Remove Software app, then if that doesn't work,
go to Prolific.
Good luck
...bill nr4c
On Mon, 11 Jul 2011 00:26:33 -0400, Paul W. Van Dyke
on this one.
...bill nr4c
On Wed, 13 Jul 2011 17:01:44 -0700 (PDT), callen1155 wrote:
Sorry to do this to you guys but .
I need some roofing filter advice:)
Currently I only have the stock 2.7K filter and it has worked fine
for
casual rag chewing and some dx'ing.
I've been operating my
there is an example of this.
...bill nr4c
Bob - W6OPO
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-dual-mikes-at-same-time-biased-and-un-biased-tp6687183p6693197.html
Sent from the Elecraft mailing list archive at Nabble.com
for the band
width.
...bill nr4c
On Wed, 5 Oct 2011 10:09:17 -0700 (PDT), rich kennedy wrote:
My setup is a simple resonant dipole, HRD/DM780 software, and a
K3/100 with latest firmware. I often operate PSK or RTTY, using the
DM780 software and running approx 35 watts. I've noticed
) check my website for a '.pdf' file.
http://nr4c.net/dev/images/PAL-FAB-Notes.pdf
More information can be found here...
http://nr4c.net/dev/pages/projects.html and look for links on the new
PAL mkII and the construction notes above.
,,,bill nr4c
this!
...bill nr4c
On Tue, 25 Oct 2011 13:09:47 +, Dave Johnson wrote:
Lu, if you have access to an SDR receiver that can record it's output
on a PC, it might be easier that using a noise source.
When comparing several microphones and headsets on my K3, I used a
Perseus SDR to play
. I do use the sub dialed down to
200 hz when chasing DX at times. But the DSP works so well that I
couln't justify the expense of the other filters for the sub. I'd keep
it.
...bill nr4c
Before I do perhaps others could say how they think the 2nd rx should
be
populated filter-wise
A while back, I saw some discount 'coupons' on the list for the K3 book
from KE7X. Are there any current discounts available for this item?
...bill nr4c
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
I was just looking thru the n1mm manual and came across the {END}
macro. Check this our as it might just do the trick.
...bill nr4c
On Tue, 15 Nov 2011 10:41:40 -0800, Fred Jensen wrote:
If there is, I haven't found it yet. The basic problem is that WL
[and
N1MM, and maybe others
UH,
QSK is Full Break IN. Would not QSK OFF be Semi-break IN?
Just curious
...bc nr4c
On Tue, 29 Nov 2011 11:39:41 -0500, Paul VanOveren wrote:
Is there a way to shut off QSK in CW mode? I only find SEMI or
FULL
NF8J
The stored file contains configuration AND calibration information and is
specific to a particular radio, including serial number.
A lot of us would like to see this broken into two files but so far not
happening.
Sent from my iPhone
...nr4c. bill
On Mar 29, 2014, at 9:01 AM, Richard hb9
and graft it to a
Heil cable.
As I recall the Amazon cable was pretty inexpensive, thin and red.
Sent from my iPhone
...nr4c. bill
On Mar 30, 2014, at 8:19 AM, John Lawrence j123...@aol.com wrote:
First of all, the KX3 is a sweet radio and have it running quickly with only
Are you using the latest K3 utility? If not try upgrading that first.
Sent from my iPhone
...nr4c. bill
On Mar 31, 2014, at 5:17 PM, Bill Coleman aa...@arrl.net wrote:
I noticed this weekend that Elecraft had updated the firmware (not beta) back
in February. So, today, I thought I would
1 - 100 of 1160 matches
Mail list logo
