Hi Stan,
This subject comes up from time to time on the reflector. Here's a link to a
previous thread:
http://www.mail-archive.com/elecraft@mailman.qth.net/msg103777.html
Here's a link to the Array Solutions RF Limiter mentioned:
http://www.arraysolutions.com/Products/as_rxfep.htm
73,
Mike K2MK
on the front of
the K3 for proper ALC indication. You should then be able to crank up RF
output with the PWR knob (unless you are in TEST mode).
73,
Mike K2MK
Mike Reublin wrote
Thanks to some excellent suggestions, I was able to get receive working,
but transmit is still a no-go.
I cannot get
Hi Fred,
I noticed on the specs that the preamp frequency range is 22 to 54 MHz. Have
you tried it on 12 meters?
73,
Mike K2MK
Fred Smith wrote
I received my new 6/10m preamp yesterday morning and installed it. I had
been using my IC-9100 for 6/10m as it has excellent preamps
Hi Bob,
This feature is disabled in CW with either one or both of the following
settings.
if CONFIG:CW QRQ is turned to ON
or if CONFIG:PB CTRL is set to SHIFT-.01
73,
Mike K2MK
KD7YZ Bob wrote
Howdy K3' people:
I've searched the manual and pushed/held/tapped a lot of K3 buttons
/order_form_parts.htm
Serial numbers might not be the best clue for those buying a previously
owned radio. The previous owner might have already made the improvement.
73,
Mike K2MK
Mike Reublin wrote
I found the mod.
On Jul 4, 2013, at 6:38 PM, Mike Reublin lt;
nf4l@
gt; wrote:
On Jul 4, 2013, at 5:47
forget to switch back to the antenna because I don't hear any stations
when I'm on the dummy load.
73,
Mike K2MK
Deni F5VJC wrote
When booting up my PC connected to the K3 it keys the TX several times
during the bootup sequence, I imagine when initialising the various
comports. I need to power up
to be a KX3 on the
SteppIR site here:
http://www.steppir.com/crankir-vertical-and-dipole
Brian was probably a beta tester. According to the top two photo captions he
took the CrankIR to Hawaii. You could drop him a line to get his
impressions.
73,
Mike K2MK
Lynn W. Taylor, WB6UUT wrote
Noticed
Hi Jack,
I like to keep the K3 manual on my computer and then search in the PDF file
for phrases. Searching for CW in SSB brought me to the top of page 55:
CONFIG:CW WGHT
tap button 1 and you'll see CW+SSB
tap button 1 again and you'll see CW-SSB
73,
Mike, K2MK
Jack Colson wrote
I thought I
Hi Mike,
Is it possible you have QSK (Full break-in) active instead of VOX (Semi
break-in).
73,
Mike K2MK
Mike K4PI wrote
I noticed when using my memories on the K3, the keying line to the amp
drops in between some words. Even if I hold the foot switch down it will
not hold he relay
the house when
it is pointed in that direction.
73,
Mike K2MK
w9hak wrote
Has anyone used the Pixel magnetic antenna with
their K3? I am instrested in your results and how
you attached the Pixel antenna to your k3.
Smith Bradford
W9HAK
--
View this message in context:
http
to the rear
jacks of the K3 and require no adapters. They are available everywhere
online for under $45.
73,
Mike K2MK
Don Baucom wrote
Fred,
Thanks. I have a lot to learn. I also read the what W4ZV had to say. I
cant wait to get home and adj the receiver.
One more question. What
Hi Bill,
That's great news. Please post the manufacturer and model number of the good
modem. I'd dump my Linksys WRT54GL in a heartbeat if I knew of one that was
less problematic.
73,
Mike K2MK
n6fb wrote
Thanks to all who answered me re birdies on every CW band in my K3. It
turns out
RF output
is noticeable on 20 through 6 meters. So I'm on the lookout for
recommendations from K3 users on a clean router.
73,
Mike K2MK
ab2tc wrote
Hi,
Modem? You guys mean router? Ethernet cables are often a very bad source
of birdies, but in my case the primary culprit was not the router
stations that you can currently easily hear. But if you have a directional
antenna and want to enjoy the band openings the PR6 will make those weaker
stations easier to hear.
73,
Mike K2MK
k6st wrote
How effective or necessary is a PR6 preamp for 6m operation? Is thing
specific to installing
to bring up
the monitor menu and make the adjustment each time.
73,
Mike K2MK
N5GE wrote
Paul,
Your monitor should have brightness and contrast controls. You
should use those to adjust the SVGA brightness and contrast, as you
would on any TV or monitor.
Setting the SVGA bias will only
Same here and I don't see a menu option within the SVGA sub menu to turn it
on.
73,
Mike K2MK
N0GC wrote
I don't see the marker in the waterfall portion of the SVGA monitor when
it is on in the P3 display.
What am I doing wrong?
--
View this message in context:
http://elecraft.365791
Hi Paul,
That's easier to fix. You must have the waterfall colors set to gray scale.
Press the P3 menu button and turn the knob until you see Wfall Clr. Then
press the knob and turn it to Default Colors. Press the knob again and you
should be good to go.
73,
Mike K2MK
KC2NYU wrote
Tnx for all
out the CrankIR for a few hours use
while the HOA police are napping.
73,
Mike K2MK
W4JBB wrote
A lot of talk has been going on about radials on the KX3 Yahoogroups
Reflector, but there is so much FOD on that reflector, I usually delete
most of the messages. Although it may have been
is a corded or wireless USB mouse connected
directly to the back of the P3. Then you would have two mice on your desk
which is probably even less desirable during the heat of a contest (unless
you're ambidextrous).
73,
Mike K2MK
VE3WDM wrote
Good morning all, just wanted to resurrect an idea that has
have a P3 you would need a RCA Y cable).
The white wire is more problematic. I extended mine and have it wired into a
15 pin fanout board for the K3 accessory socket.
73,
Mike K2MK
Jim AB3CV wrote
The little 3 pin connector without any strain relief and wires hanging off
it give me concern
the
cable through several times.
73,
Mike K2MK
AB1SX wrote
Never noticed it because while setting up the kx3 I was also setting
everything up on my computer. I am a new ham and was getting the logging
software etc all set up. I recently was using the kx3 without the
computer plugged
-Adhesive-12-Inch-20-Square-Feet/dp/B002AS9NB2/ref=pd_sim_hg_2
It is available at Home Depot and Lowes in smaller/cheaper rolls.
73,
Mike K2MK
Jim Brown-10 wrote
On 4/11/2013 5:03 AM,
pastormg2@
wrote:
I am considering a P3 to go along with my K3. I would like to sit the P3
on top of my
that's a
waffle design) to give the P3 a little more grip. I cut out the liner where
it covered the K3 speaker. Some speaker volume is sacrificed with the P3 on
top but I mostly use headphones so it was not a problem.
73,
Mike K2MK
pastor...@verizon.net wrote
Good Morning, I am considering
that are a problem.
73,
Mike K2MK
Bruce Meier-2 wrote
Update
Not sure how I missed this, but I just determined that this ONLY happens
when NOT in SPLIT mode. And it happens on BOTH K3s. I had my other K3
in split and did not notice it. I can reproduce the same symptom on both
K3s when
but it was not really critical for my style of operating. For me the
SVGA option was worth the cost. For others (perhaps with younger eyes) it
might not be worth the cost.
73,
Mike K2MK
Benny Aumala-2 wrote
I got P3 here some weeks ago. It has transformed my way of band-life
more than expected. I seem to chase
Hi Brian,
Turn CONFIG:CW QRQ to OFF.
73,
Mike K2MK
alsopb wrote
I was doing something odd. Stock 2.7KHz filter, CW mode, V4.61.
Removed all equalization.
Wanted to adjust high cut or low cut. Tapped shift control. Did not
revert to high cut/low cut mode. Ditto for tapping width
the problems will only
occur on one or two bands. If you have difficulty with these manual
adjustments come back with questions and those that have performed the
adjustments will help guide you through.
73,
Mike K2MK
Gordon LaPoint wrote
Hi,
I'm having problems with my K3-100 with power out
in coarse tuning if interest warrants
a change.
From a personal point of view I was not able to manually tune CW signals in
coarse mode (one digit showing). Even with the assistance of my P3 I found
it far to difficult for my unsteady hands to accomplish the task.
73,
Mike K2MK
KC2NYU wrote
Phil - I
effectiveness is
influenced by the CWT threshold setting. Mine is set to THR=2. You can see
this setting by holding the CWT button and you can change it by turning
VFO-A.
73,
Mike K2MK
Phil Hystad-3 wrote
I had the same problem the other day. Instead of driving the signal to
the center of CWT
Hi Joe,
I opened the menu option on my P3 and here are the available resolutions:
1024 x 768
1280 x 1024
1440 x 900
1920 x 1080
1920 x 1080 alt
73,
Mike K2MK
Joe Subich, W4TV-4 wrote
What native resolutions does the P3SVGA support - just the four listed
on the web page? I see quite a few
checked the menu choices for the SVGA card and 1024 x 768 is one of
the available choices.
73,
Mike K2MK
Paul VanOveren-2 wrote
The SVGA card arrives for my P3 today and I have the opportunity to get a
free flat screen monitor 1024 x 768 resolution. Just wondering if that is
sufficient or whether
in the heat
of the pileup he tapped A/B when he should have held for BSET. I was
surprised at how long it took him to get things back to normal.
I'm spoiled by my P3. An A/B mistake or a LINK versus UNLINK error is really
easy to spot on the P3.
73,
Mike K2MK
--
View this message in context:
http
had at the
bottom of the screen. The image size was 1282KB for my 1280 x 1024 monitor
setting.
You might want to attach a pull string to your thumb drive. It's close
proximity to the SVGA connector and the serial connector made it tough to
get a good grip for thumb drive extraction.
73,
Mike K2MK
of the monitor button flips it between the PC and the P3.
73,
Mike K2MK
Paul VanOveren-2 wrote
I have had the P3 for several months now and debating whether or not to
purchase the SVGA board and an additional monitor for the larger display.
I
would be interested in anyone's comments about
Hi Jim,
As a point of curiosity here's a posting from Wayne (04/15/2010) describing
the reason for using steel in the P3 enclosure:
/The P3 enclosure is being fabricated entirely from corrosion-resistant
steel (plated before painting) rather than aluminum. Production and
field test units
(like some RTTY
contests or the Sweepstakes contest) I can tune in on a waterfall a half
inch or more below the the break line and just wait for the station to
return. A real point bonanza.
73,
Mike K2MK
Dale Boresz wrote
Partial quote from Dale:
but the really big 'plus' to the external
available on
the SVGA output. Next, you might want to get a monitor that has at least two
inputs with a button on the front to toggle between inputs. This will enable
you to use it with your desktop PC as an expansion monitor when you are not
using it to display the ham bands.
73,
Mike K2MK
desired
settings. This also applies in an identical manner to NR.
73,
Mike K2MK
Matthew Zilmer-2 wrote
Sorry. Next time I'll read the entire email before shooting my mouth off.
Matt Zilmer
Consultant - Product Management Dept.
Magellan Navigation / MiTAC Digital Corp.
Tel: (909) 394-6052
Hi Mike,
I did a quick search on the word attenuation and found this older e-mail
from Lyle of the Elecraft crew.
73,
Mike K2MK
*Lyle Johnson Tue, 25 Nov 2008 12:42:26 -0800
How much attenuation does the Attenuator put in line?
Approximately 10 dB, not adjustable.
73,
Lyle KK7P*
Mike
this feature so any questions you might have should be quickly
answered.
73,
Mike K2MK
G4HUE wrote
Hi guys, there is a keyboard connector and another USB connector on the
rear of the P3 when fitted with the VGA card. I have read through the
documentation on the Elecraft website, the KE7X book
cycling of the P3 power button.
73,
Mike K2MK
Tom-2 wrote
My P3 display periodically freezes. I've run a couple of contests
with it going and it seems fine, but every once in awhile, it will just
lock up. I turn it off and back on and it's ok. Any ideas??
Tom, K4IE
--
View
Hi Paula,
Do you have a separate receive only antenna connected to the KXV3A RX IN BNC
connector. If yes, then you are possibly hearing the COR (carrier operated
relay) protecting the receiver front end from overload. Disconnect the
antenna connector and see if the noise stops.
73,
Mike K2MK
to Tracking Mode and the VFO cursor jumps to center screen.
Press it again and your back in Fixed-Tune mode. So it's a push-push
operation to get the cursor to center screen and return to Fixed-Tune mode.
You can also have a K3 button perform this operation as a macro.
73,
Mike K2MK
k6dgw wrote
Hi Iain,
When I see a word whose definition eludes me I usually Google it for a quick
Urban Dictionary or Wiki definition. A word of caution, if you don't know
what Munging means you are going to want to Google Data Munging.
73,
Mike K2MK
Iain MacDonnell - N6ML-2 wrote
This is not a Yahoo
through cables
from assorted suppliers. Here are links to two suppliers:
http://www.winfordeng.com/products/ext15hd.php
http://www.monoprice.com/products/product.asp?c_id=102cp_id=10215cs_id=1021501p_id=544seq=1format=2
73,
Mike K2MK
Bill Robbins wrote
I bought a Logitech External speaker
Correction:
The 2nd link I sent you (Monoprice) is incorrect. It shows 15 pins arranged
in two rows. The first link (Windord) is correct, 15 pins in 3 rows.
73,
Mike K2MK
Mike K2MK wrote
Hi Bill,
If you Google VGA plug wiring you'll see that not all pins are connected
and some are shorted
stressed. So with this
information available there should be no reason to shy away from future
downloads.
73,
Mike K2MK
Bill Clarke wrote
Reading about the problems involving upgrading the firmware, resets,
calibrations, etc. - makes me think that I won't be upgrading here. My
K3 is running
totally undamaged and a new
screw was easily put into place. My thanks to the poster that made the
recommendation.
73,
Mike K2MK
Fabio IZ4AFW / NZ1W wrote
Hi guys,
today I decided to try to apply a mod (Audio Low Pass filter) to my
beloved K3.
My K3 was born in September, 2009 and I
Hi Alan,
It's not just the electrons that are being inconvenienced by this recurring
posting.
Between inconvenienced electrons and stinking violins I'm hoping the New
Year brings new cliches.
73,
Mike K2MK
Alan Grant wrote
No trees were damaged in sending this Email, however, many
dial to your
desired frequency and begin transmitting.
73,
Mike K2MK
goldtr8 wrote
I can not get my K3 to TX in split mode for CW.
What is the magic setting, I put it in split mode and change the frq to
1k up but it still does TX on RX frequency.
There has to be something simple to do
to
boost the volume level in my weaker right ear.
Is there a way in K3 firmware to re-balance the left and right channels
using just the Main RX. If not, is anybody using an external device that
accomplishes this task? Preferably one that is immune to RF.
73,
Mike K2MK
--
View this message
Hi Bob,
That should not happen. The problem could be related to your computer
software refreshing VFO A while you are holding the REV button. What
software are you running?
73,
Mike K2MK
KD7YZ Bob wrote
Howdy K3' people:
I tried out my new K3 attempting to jump into the ZL9HR melee on 40m
added the SVGA option and I
put an LCD monitor on a swivel arm overhanging the K3.
73,
Mike K2MK
pastor...@verizon.net wrote
I would like to purchase a P3 in the future to go with my K3. But I don't
have too much room left on the table to mount them side by side. Does
anyone know of a desktop
the direction for every
station you work so it's really not important to me to have my PC turn the
antenna constantly.
The G-450A is a perfect companion for a hex beam. You may want to join the
Hex Beam Yahoo group for additional opinions.
http://groups.yahoo.com/group/hex-beam/
73,
Mike K2MK
Ron Midwin
good
communication between the two is to look at the top center of the P3 screen.
The current K3 frequency should be displayed regardless of which mode you
are in. If you see a zero on the screen you have lost communication.
73,
Mike K2MK
k6dgw wrote
P3 was just fine. Then, rig still on during
I worked a huge number of QRP stations during the CW Sweepstakes this
weekend. Many more than has been usual. Must be all of those new KX3
operators taking it out for a spin.
73,
Mike K2MK
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KX3-in-Sweepstakes-tp7565078.html
Hi Mike,
Page 16 of the K3 Programmers Reference Rev D6.
SPKR+PH = MN097
73,
Mike K2MK
Mike-14-3 wrote
I managed to erase the macro I had for toggling the external speaker
on/off and can't find the command again.
73,
Mike NF4L
--
View this message in context:
http://elecraft.365791
either the RIT
and/or XIT is activated the knob only controls the RIT/XIT frequency and not
VFO A frequency.
73,
Mike K2MK
Mike-14-3 wrote
Playing with the P3 today I just noticed a bit of quirky behaviour. When
I turn the RIT/XIT button on the K3, whether RIT/XIT is on or off, I get
movement
of the research.
73,
Mike K2MK
Keith Heimbold wrote
I embarked on a project to move parts from one K3 to another and I got the
rigs back from my tech elmer tonight. After getting the K3s home, I
decided to follow the procedure to get them operating again.
I had my tech elmer transfer the KAT3, KRX3
Hi Keith,
You should review the KRX3 assembly/installation manual. There's a resistor
that may need to be modified (see page 21) and maybe some other stuff as
well.
73,
Mike K2MK
Keith Heimbold wrote
I have sent my Elmer tech friend a couple emails asking him if he swapped
out the other
Hi Bill,
Deja Vu all over again.
http://www.mail-archive.com/elecraft@mailman.qth.net/msg137871.html
The majority opinion in June was to go for another 35 amp Astron. That's
what I use.
73,
Mike K2MK
Bill wrote
I am about to replace my 35 year old Astron 35 amp supply. The choices
for diversity). Look
at the upper display and make sure the second decimal point is not blinking.
(The blinking decimal point is the only way we know we are in diversity).
73,
Mike K2MK
Dave Weiss wrote
Hi Gang:
I think I am experiencing an issue with the sub receiver on my K3. On all
bands
of the P3.
73,
Mike K2MK
Dale Boresz wrote
When using the second receiver w/ the K3 and P3, is there a way to have
a second cursor representing the frequency of the 2nd rx on the P3?
Currently the only way I have been able to get this to work is to
engage Split, but my goal is to be able
decode
window is coming in on the right stereo channel.
73,
Mike K2MK
Joe K2UF wrote
Just started playing with RTTY. How can I operate split using AFSK A
mode?
Any help?
Joe K2UF
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-RTTY-tp7563219p7563225.html
Sent
previously gone to CW mode and pressed ALT prior to going to USB.
73,
Mike K2MK
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K3-Help-with-SSB-CW-on-6-meters-tp7562446.html
Sent from the Elecraft mailing list archive at Nabble.com
Hi Don,
I would like to echo Lee's comments. After about 2 years of use my Begali
paddle became what I can only call sluggish when used with my K3. I
contacted Begali and he sent me an abrasive cleaning strip. It differs from
the strip that comes with the paddle. This was thicker and required me
have been a better choice. If it is dust buildup then I think even
gold contacts would require cleaning. I do keep the supplied plastic cover
on the paddle at all times.
73,
Mike K2MK
Donald Thompson wrote
Hi Bruna,
I moved my Leonessa Key from the CW Machine to my new K3 and encountered
to YES it does affect what you hear in the
headphones. It's best to turn this feature to NO when using headphones.
73,
Mike K2MK
Gordon LaPoint wrote
Hi,
Is it possible to put the audio from the main RX to both Right and
Left when the sub
RX is off, automatically, then switch back
Hi Jim,
Tap 1, 2, etc. refers to the 12 button keypad. You'll see the numbers
printed in red on each button. These buttons expand the functionality of
several menu/configuration choices.
73,
Mike K2MK
James Navarre wrote
Being a newbe to the list. My first question is while setting up
Hi Terry,
Try running the RF Gain calibration from the K3 Utility Program.
73,
Mike K2MK
terry220 wrote
hi
i have just received my k3 from watersstanton here in the uk.i have a
slight problem
with the rf gain on receive if you turn the rf gain contril fully
clockwise the signal goes
in RTTY.
73,
Mike K2MK
Roy Morris-6 wrote
From time to time I have seen some macros for shortcuts to various K3
functions. At the time I did not pay enough attention and did not copy
them
down. I wonder if there is a comprehensive list somewhere for the K3
macros
and also a list
Hi Benny,
CONFIG:PWR SET
tap 1 button
73,
Mike K2MK
Benny Aumala-2 wrote
Trying to adjust power output, the potmeter do not react
but VFO B gives reading LOCKED. Power is fixed in 100W.
Difficult to find reason in Owners Manual.
Benny OH9NB
--
View this message in context
writelog.ini file.
I know there are true ini files and mirror image ini files. I run Vista and
my ini file is in the Windows directory but this may not be true for all
operating systems. Be very careful. And your definitions should be preceded
by the following:
[Elecraft_K3_commands]
73,
Mike K2MK
Fred
. Although I think I had trouble finding one
of the special keys on the Amazon keyboard that is used for the special CW
characters shown at the bottom of the DATA screen. I didn't consider this a
deal breaker.
73,
Mike K2MK
vk4tux wrote
Get it here with free shipping
Go to http
Hi Hugh,
15 pin Y cable. Fully shielded, all pins wired end to end:
http://www.winfordeng.com/products/cdy15hd.php
15 pin cables. Fully shielded, all pins wired:
http://www.winfordeng.com/products/ext15hd.php
15 pin breakout board:
http://www.winfordeng.com/products/cat_brk.php
73,
Mike K2MK
cause.
73,
Mike K2MK
reliant325 wrote
I recently acquired a K3 which I decided to try on WSPR.
I have been active on WSPR for many months now. I setup the K3 with the
same interface and PC as I use with my IC7700.
The setup with the K3 was straightforward and worked well.however.
I
with the RS232 and ACC connectors. Be extremely
careful not to over tighten the standoffs on either side of those two
connectors when you reinstall this board.
After installation it is necessary to change CONFIG:KXV3 from NOT INST to
NOR.
73,
Mike K2MK
goldtr8 wrote
I think that I need to add
overridden when
diversity is used and reverts to MAIN in left ear and SUB in right ear. So
you might have one arrangement set for general SUB RX use and when you go to
diversity it changes.
73,
Mike K2MK
Jim Bennett wrote
I just recently added the sub receiver to my K3. I've been using the Sub
to the AUX jack
or if you have wired the jack incorrectly internally you will suddenly lose
volume in your right ear.
73,
Mike K2MK
Jim Bennett wrote
Hi Scott, yes - there is a separate antenna. I have an 88 foot long
doublet connected to ANT 1 and a ground mounted Hustler 5BTV connected to
Ant
Hi Ian,
My 5 year old SteppIR controller works fine at 38400 bps.
73,
Mike K2MK
Ian White GM3SEK wrote
The older SteppIR controller can only handle up to 19200 bps. That speed
must be manually configured in all three devices - the SteppIR
controller, the computer and the P3
Hi Mike,
Think of the leg of the Y cable that goes to the K3 as the Elecraft leg.
Take the cable that now goes to the K3 and move it to the P3. Then take the
short serial cable supplied with the P3 and connect it between the P3 and
the K3.
73,
Mike K2MK
Mike-14-3 wrote
I've got a P3 coming
is contained in the box.
73,
Mike K2MK
Mike-14-3 wrote
Thanks, Mike.
Just to make sure my age fuzzed brain got it:
The Y stays where it is, plugged into the K3. The cable from the
computer moves from that to the P3, then the shorty goes from the P3 to
the Y.
73, Mike NF4L
On 8/1/12 2:00
somebody else can comment.
73,
Mike K2MK
AMFMTV wrote
Hi Everyone,
Is it just that I haven't read every installment of the reflector, or
what?
After installing the latest release software, the AM synchronous mode no
longer will track and lock onto the carrier. Also, I no longer can
beta release
firmware and only upload new releases once they move to the production
level. By that time the firmware has been thoroughly tested by hundreds of
users.
73,
Mike K2MK
Bill wrote
While my K3 is in California being repaired, I have been considering the
P3 as an addition when
Hi John,
Yes they can be sensitive but that's the beauty of Home Depot. Return it to
the store and try another brand. Or better yet, take it out, replace it with
a regular receptacle and save it for when you sell the house.
73,
Mike K2MK
John Shadle wrote
Hi all,
I realize
don't
have the means to determine if I am actually transmitting on VFO A freq or
VFO B freq. I'd like to think that it is just a P3 glitch but extra care
should certainly be taken until this problem is totally understood.
73,
Mike K2MK
Jim Sheldon-2 wrote
I've also found that if you are IN split
keyboard. So I'm
still wondering if the keyboard input part of this beta release has been
implemented.
73,
Mike K2MK
Iain MacDonnell - N6ML-2 wrote
Mike,
See:
http://elecraft.365791.n2.nabble.com/P3-Beta-firmware-available-Data-terminal-mode-td7559633.html
73,
~iain / N6ML
into the
LINE IN connector on the back of the K3 or your PC line output needs to be
cranked up using the audio control panel.
73,
Mike K2MK
VE3NFK wrote
Hi
Probably missing something stupid... WSPR and PSK etc did not show any
output when transmitting...
(they used too)... After 'messing
happy with PC software control
of RTTY and PSK. I'll debug the problem later when the P3 is able to do some
other interesting keyboard related things.
73,
Mike K2MK
Rick Prather-2 wrote
Mike,
I guess it's too early in the morning. Of course you are in PSK-D or
FSK-D or you wouldn't
Hi Dave,
This is very embarrassing. I never saw the PDF file among the other
documents that were extracted from the zipped file. It's quite extensive.
Thanks for pointing that out.
73,
Mike K2MK
David Pratt-4 wrote
Mike - It sounds as though you have not read the PDF file
to help you.
73,
Mike K2MK
Steve Reichlyn wrote
I have routinely been able to update software in both K3s in the
usual manner. I tried to update
to 4.51 today and the latest K3 urility that comes up on the Elecraft
site is 1.12.3.28. This utility
will not allow me to update to 4.51. I
Hi John,
What functionality is the external keyboard supposed to provide under the
1.05 SVGA firmware? I haven't seen any posts from anybody indicating that
they are using a keyboard. With every other new feature there are usually
numerous posts describing the great new features.
73,
Mike K2MK
receiver from strong
signals coming in on the RX IN port. It sounds like the relay was not able
to help and you might have some damage to the front end of the K3 receiver.
73,
Mike K2MK
Gil G. wrote
On Tue, 2012-07-24 at 18:14 +0200, Jacques Paoli wrote:
Bonsoir. Pas ou presque de réception
Hi Hank,
No. It would be nice for those that have wide external monitors. Perhaps it
is on the firmware wish list.
73,
Mike K2MK
Hank Garretson wrote
I'm sure I could dig out the answer from manual, but please a quick
question:
Can one have different parameters for P3 and SVGA
a narrower filter later. If money is not an issue buy both.
I also have the 1000Hz filter and never find myself operating with a
bandwidth in the 400Hz to 1000Hz range. One day I'll pull it out and sell
it. Had I used my own advice I could have saved some money.
73,
Mike K2MK
Don KB1YBG wrote
matched filters in your sub RX. But
that move could lower the resale value of your K3. More food for thought.
73,
Mike K2MK
Phillip Shepard wrote
My understanding is that diversity receive works best with matched
receiver
topologies. Should the subRx have the same filter array as the main
incorrectly.
You could also have the sub set up in diversity mode. In diversity you'll be
listening to VFO A in both ears regardless of what is displayed in VFO B.
The tip off is a blinking decimal point (the right decimal point) in the VFO
A display.
73,
Mike K2MK
w0mu wrote
I installed this 2nd
the other things in your macro) when I tap my M4 button.
73,
Mike K2MK
Stewart@twinwood wrote
The following macro runs OK from the K3 Utility program,
but not when assigned to a function key - why ?
TUNEONMN019;MP001;MN255;SWH16;
73
Stewart G3RXQ
--
View this message in context
receive antenna for the low bands then the sub RX can also be used for
diversity reception. This is where you can listen to your transmit antenna
in one ear and your receive antenna in the other ear. For some this is a
powerful tool for weak signal work.
73,
Mike K2MK
RobertG wrote
I have never
is not required to utilize a second antenna. You can
use a second antenna with the main RX with the addition of the optional
KXV3A board.
73,
Mike K2MK
Brian Maynard wrote
I thought this through and chose the P3. The subRX requires a second
antenna - which I did not have - and the matching filters, so
201 - 300 of 512 matches
Mail list logo
