I agree and get NEW brake Hoses while you are at it.
On 10/29/2012 17:23, Dan Penoff wrote:
No rebuilding of calipers. It's not cost effective, nor is it safe to do.
Buy a pair of remains from Rusty and be done with it.
Dan
Sent from my iPad
On Oct 29, 2012, at 6:12 PM, Bob Rentfro
Jump the Pos wire from Battery to the small terminal next to it. I use a
remote
starter switch from FLAPS for this.
Also you can push start it too.
BTW will pull your parts this weekend.
Russ
On 10/26/2012 10:43, Bob Rentfro wrote:
How do start my 240D using a jumper down around the starter?
Advance sells Wix filters for the 616 617 engines don't know about the
60x motors.
When I bought SWMBO's 240D there was one in the trunk from PO. For grins
I cut it apart construction was on the flimsy side filter material was
thin and not as much
of it as the ones Rusty sells. I'll take the
BMW X-5
On 10/6/2012 17:50, Kaleb C. Striplin wrote:
What vehicle is it?
Sent from my iPhone
On Oct 6, 2012, at 5:11 PM, Jim Cathey j...@windwireless.net wrote:
Yesterday Jill called me in the night and the car was acting up.
Lights on the dash, no power, died at stops, etc. Badness. She
Like Craig said check the ground for the cluster. I had the same problem
on SWMBO's
240D when I got it.
Do a Citric Acid flush and use the MB recommended Coolant.
I have a spare cluster if you need a gauge.
Let me know what part of the door handle you need.
I also have a manual tranny shifter
Got you beat but way behind Wilton 44 1/4 years here.
Russ W.
On 9/10/2012 16:25, Randy Bennell wrote:
With the exception of Wilton, you are all amateurs so far. Barbara and
I have been married 39 years so far.
Not sure how much longer though as she is becoming upset with my snoring.
Randy
Getting some wind gust now. No heavy rain yet.
Forecast is saying won't pass BR until tomorrow night.
So standing by for a bunch of rain tomorrow.
N.O. has had some heavy rain but NO flooding.
At Midnight track is WNW @7 mph.
Russ W.
Hunkered down in Gonzales, La
On 8/28/2012 22:18, andrew
Good Luck Hope it goes well.
On 8/28/2012 23:23, Craig wrote:
This afternoon, the HR person at the W.M. Keck Observatory called and
asked if I wanted to continue with the interview process. I said, Yes.
(What else would I answer?).
He said they wanted to do a panel interview over the telephone
I used Astro Lube when I did the front seal on My 300SD.
It's water soluble and wont hurt the rubber.
Russ W
On 8/25/2012 23:03, andrew strasfogel wrote:
The body shop did a half assed job installing a new front sunroof seal
when they repainted my 1985 300TD. I can't complain tho, because they
Oppps ! Make that AstroGlide like KY but better
On 8/26/2012 13:06, Gerry Archer wrote:
Astro Lube, Astrolube, Ky Jelly, ?
http://www.astrolube.com/products.php
Gerry
From: Russ Williams rawil...@eatel.net
I used Astro Lube when I did the front seal on My 300SD.
It's water
Receiving You 5 by 5
On 8/19/2012 12:50, WILTON wrote:
Test
Wilton
___
http://www.okiebenz.com
For new and used parts go to www.okiebenz.com
To search list archives http://www.okiebenz.com/archive/
To Unsubscribe or change delivery options go to:
not.
Whasup?
Wilton
- Original Message - From: Russ Williams rawil...@eatel.net
To: Mercedes Discussion List mercedes@okiebenz.com
Sent: Sunday, August 19, 2012 1:53 PM
Subject: Re: [MBZ] Lost again?
Receiving You 5 by 5
On 8/19/2012 12:50, WILTON wrote:
Test
Wilton
Back in 1980 I was working for a company out of Pearland, Tx.
Four days prior to this I had just taken delivery of our 4th and last
Sikorsky S-76.
And flown it from the Sikorsky Delivery facility in West Palm Beach to
Pearland.
During the flight from NEW to Pear George (Auto Pilot) would kick
Yes Very Tasteful
On 8/8/2012 09:23, buymbpa...@gmail.com wrote:
Spam? Spam? It was a tasteful advertisement.
Sent on the Sprint® Now Network from my BlackBerry®
-Original Message-
From: Rich Thomas richthomas79td...@constructivity.net
Sender: mercedes-boun...@okiebenz.com
Date: Wed,
Hi E,
I have both the left and right on my dead 240D that you can have. I'll
have to
look at their condition. I'll let you know tomorrow.
Russ W.
On 7/30/2012 17:23, ernest breakfield wrote:
sent the following to a couple of used parts suppliers (including here
and elsewhere), but haven't
High side should be in the 240 psi range for that OAT.
104(OAT)x2+32
Russ W.
On 7/29/2012 15:14, OK Don wrote:
The van is not blowing ICE COLD AIR. It's blowing 68F, not cold. It was
COLD when it was new in 1997.I hooked up the guages, and read low side
of 28 and high of 160 at 1600-2000 RPM.
Wilton try the pharm @ Sam's while you are there.
We switch to them years ago saved about 10 to 15% over the rest.
Russ W.
On 7/5/2012 09:41, WILTON wrote:
'Been trying to think of somewhere I need to go today to show off the
glistening black and to feel the AC blowing ICE COLD. Probably go to
Around here NAPA carries it in the 50/50 formula. One Pep Boys (Yuck)
has it.
None of the O'Reiley's carry it and wont order it. Car Quest will order
it for you.
Russ W.
'84 300D
'83 240D w/dead Manny Tranny
'03 Stratus
On 7/1/2012 12:36, Rick Hawkins Java wrote:
i've always run the G05 and
You can request ATT drop your voice with copper lines too a friend has
it. Just ATT DSL w/ No
Telephone number. He uses a Magic Jack for his land line.
Russ W.
On 6/22/2012 15:29, Allan Streib wrote:
On Fri, Jun 22, 2012, at 01:20 PM, Craig wrote:
On Fri, 22 Jun 2012 12:03:25 -0700 (PDT)
Comcast is going to the Digital receivers to stifle Cable Theft.
The signal from them is going to be encrypted so you have to have a box
to receive.
Also makes it easier to cut off customers that don't pay the bills, No
longer have to send
a tech to climb the pole to disconnect just have the
Not sure. But I have a buddy that travels Amtrac from Hammond.La to
Memphis about every 3 weeks to visit his sick mother. He says it cheaper
than driving and han not had any problems with
Amtrac.
How long are you in Nawilns for? I'm only 45 min up I 10 from there.
Russ W.
On 6/18/2012 18:49,
Loren
I sent your message to the Owner of AGCO Automotive he replied back with
this.
Have them verify fuel pressure and volume. It is NOT enough to have
pressure. It must have the correct pressure and full volume.
Hope this helps.
Russ
On 6/3/2012 21:00, Dieselhead wrote:
A young man who
80 Mph isn't fast
On 6/1/2012 10:41, Randy Bennell wrote:
Gee, who knew a Hyundai could go that fast??
Randy
On 31/05/2012 7:33 PM, Gerry Archer wrote:
The police of South Korea investigate the reasons of a bizarre car
accident, which occurred to the latest model of Hyundai Sonata. The
car
A 240 fan won't turn with the engine off. They have No clutch assy.
Direct drive from the belts.
The first 240 I owned had a plastic bladed fan and did the same as yours
at cruise speed. One blade let go on the way to Bristol Tenn. one night.
Made one H*ll of a racket. Picked up from a P-N-P a
Rick,
I need the Passenger side Mirror (Manual Verson) for a 2001 -2006 Dodge
Stratus or
Chrysler Sebring if you can find one. I'll pay you for your time plus
cost and S/H.
Thanks
Russ W.
On 5/23/2012 19:17, Rick Knoble wrote:
Tomorrow is 1/2 price day at P-N-P. I was going to pick up an
Gerry,
I use Bounce Fabric Softener Sheets to remove Love Bugs.
Wet the bug infected area and the sheet start wiping.
It will take some elbow grease to get the one that are
baked on but they will come off and it's safe on paint and wax.
I also treat my windshield with Rainex it keeps the little
Yep I agree. That's what my buddy found.
On 5/12/2012 18:01, Dan Penoff wrote:
PAM just makes a mess. Don't bother.
Dan
On May 12, 2012, at 6:27 PM, Gerry Archerarche...@embarqmail.com wrote:
Gotta try those fixes. I vaguely remember something about
Pam but never heard of the other ones.
I got one too form Andrew.
Dan you can add me too.
Russ W.
On 5/9/2012 21:17, Alex Chamberlain wrote:
On May 9, 2012 5:50 PM, Dan Penofflwb...@yahoo.com wrote:
I know some of you are LinkedIn members, as I have connected with some of
you.
Must be catching. I just got an invite from Andrew
Brian
Try Rock Auto, is this the one you need?
http://www.rockauto.com/catalog/moreinfo.php?pk=1333823
Russ W.
On 5/6/2012 21:47, Brian Toscano wrote:
Quadratec and others only have the upper and lower radiator hoses (which
are also still available from the dealer). Its the lines to/from the
Better be they supply most of the hoses for the US manufactures.
According the my guy at the Local FAPS.
On 5/7/2012 16:14, Brian Toscano wrote:
Thanks for another idea.
Is Goodyear hose any good?
On Mon, May 7, 2012 at 8:26 AM, Russ Williamsrawil...@eatel.net wrote:
Brian
Try Rock
Yep you can use it.
Read this http://www.livinghiho.com/article/hydrogen-peroxide-vs-bleach
Russ W
On 4/11/2012 4:51 PM, Jerry Herrman wrote:
I debated whether or not to submit this question to the list, but decided to do
so after reviewing the most recent topics.
Here is my question, in
Not quite true.
Sales tax is paid to the State thru the Local Sheriff Dept who is the
tax collector
for the state and Parish.
If you buy a vech. in Miss or Ark and paid taxes there you only pay the
difference
in taxes if your local taxes is more.
If you buy a vech in Texas and tell them you
It's a Group 49 battery that you need.
On 4/4/2012 11:21 AM, Randy Bennell wrote:
Cannot recall. The last time I went there with my wife, I was checking
out the batteries. They have a fair selection but of course, the book
does not go back far enough to indicate whether they think it would
That's what I used in SWMBO 240 hasn't made a peep since and needle
steady as rock.
Mobil 1 ATF.
On 4/2/2012 7:30 PM, OK Don wrote:
IIRC, which I might not, auto tranny fluid was one suggestion several years
ago, so it's what I used in the W115.
On Mon, Apr 2, 2012 at 6:51 PM, clay
Rich take it to the shop when you go press the new BJ's in and use the Press
to compress the spring enough to release the plates.
On 3/31/2012 10:55 AM, Rich Thomas wrote:
I am rebuilding the front end of mama's 300SD. Bought this spring
compressor that Max found,
I guess you have USAA for your Home Owners Policy. Check with them
and see if the damage to the cars are covered under it.
In early 92 my Grand Voyager was broken into thru the sliding door.
No Comp on vech. but HO policy covered the repairs.
I HATE Slime balls that do stuff like this.
Russ W.
Manfred,
You can go to crucial.com or newegg.com and use their memory finder
to see how much and what kind of ram the lappy uses.
Russ W.
On 3/15/2012 8:54 AM, MG wrote:
I can give them a try. It would be real cool if they work in it. The
manual doesn't mention any that big but then it didn't
Congratulations to the Proud Parents Grand Parents
My 4th grand daughter, born today at 2:17PM
___
http://www.okiebenz.com
For new and used parts go to www.okiebenz.com
To search list archives http://www.okiebenz.com/archive/
To Unsubscribe or change
Not out there But I am Here . :-D
Russ W.
On 2/24/2012 11:31 AM, Randy Bennell wrote:
Slow list today.
Anyone out there?
Randy
___
http://www.okiebenz.com
For new and used parts go to www.okiebenz.com
To search list archives
Try looking at Newegg Rich
On 2/13/2012 2:42 PM, Rich Thomas wrote:
My free Dell Optiplex 745 requires the Dell OptiPlex 745 Desktop
Computer takes the PC2-4200/5300/6400 DDR2 SDRAM DIMMs. Supports Dual
Channel DDR2. For some reason these seem rather expensive (a lot more
than free, like the
76 here @ 1338hrs
On 1/20/2012 12:51 PM, Kaleb C. Striplin wrote:
It's in the 60's here
Sent from my iPhone
On Jan 20, 2012, at 11:27 AM, Dan Penofflwb...@yahoo.com wrote:
I wasn't going to mention that it's already in the 70s here, but since Kaleb
brought it up
Sorry.
Dan
Sent
Which 123 is the car? 240D or 300D?
Russ W.
On 1/16/2012 4:38 PM, Rick Knoble wrote:
Okay. SWMBO MB engine is bouncing off the frame and making all kinds of racket.
I interpret this to mean in needs engine shocks. What else do I need to change
with them?
Motor mounts aren't too pricey.
Rick,
If the motor mount on the driver's side is collapsed check to see if the oil
cooler line has clearance where it runs past the spring upper mount. If
there's
no clearance change the mount ASAP. Eng vibration WILL rub a hole in the
line
and make the BP oil spill look like a minor leak.
Allan,
I worked on the same model last week with the same problem.
The processor has been overheated. This is a problem with the Compaq's
that has the Athlon processor. CPU cooling fan and heatsink get clogged up
with dust air flow drops processor temp climbs and eventually the processor
And A Merry Christmas to All
Russ W.
On 12/25/2011 9:06 AM, Craig wrote:
On Sun, 25 Dec 2011 08:19:40 -0600 Donald Snookdsn...@mtsqh.com wrote:
Merry Christmas to everyone!
And Merry Christmas to you, too, Don!
Craig
___
http://www.okiebenz.com
For
Spot on Jim.
Fog light misuse is one of my bugs too.
Russ W.
On 12/18/2011 12:15 PM, Jim Cathey wrote:
I've put another little rant on my web site:
http://userweb.windwireless.net/~jimc/fog.html
This may evolve a bit over time, but I've been wanting
to say this for some time.
-- Jim
You can replace the caps yourself. Here are two links that sell sets of
caps for the GX 270
http://thecapking.com/gx270.html
http://www.badcaps.net/store/product_info.php?cPath=1_4products_id=2
Bad Caps will also do the job for you for a price, He's located in Mizzou.
Russ W.
On 12/14/2011
If you do just the tip Your Fuzes WILL MELT :-D
On 12/4/2011 11:36 AM, Dimitri Seretakis wrote:
How about just the tip? Sorry, I couldn't help myself:)
Sent from my iPhone
On Dec 4, 2011, at 11:38 AM, Dieselhead126die...@gmail.com wrote:
As Elmer Fudd used to say: Be vewy vewy careful
NO WAY Cajun
On 12/4/2011 5:35 PM, Dimitri Seretakis wrote:
Maybe it's a Cajun pronunciation.
Sent from my iPhone
On Dec 4, 2011, at 6:21 PM, Dieselhead126die...@gmail.com wrote:
What's an enjuion
___
http://www.okiebenz.com
For new and used parts go to
He's lucky. I had a co-worker who had an Olds with the converted Diesel 350.
He ran out of fuel about a half of mile from our heliport, Rather than
walking to our hanger
and getting a gal of JP4 he poured about 2 gal of gas he had in a can
in the trunk (it was for the base mower). Cranked up
On 11/24/2011 6:53 PM, Dieselhead wrote:
Some year I need to solder a hot wire to the left light terminal on
the 81 240D. I think it has been out the whole time i've had the
car. Sounds like I should try stuffing in some alum foil at that
time. Can someone elaborate on this? Is it just
Get a can of Right Stuff Gasket sealer. I've used sealing up Antenna
Motors. Easy to
remove if you have to open the motor again. Don't go overboard with it
though.
Russ W.
On 10/22/2011 7:56 PM, Allan Streib wrote:
Allan Streibstr...@cs.indiana.edu writes:
I'm not sure how to seal up the
They failed due to 3 reasons.
They were all Diesel powered so most ran out of fuel. Tanks went dry.
Tanks were located in as low spot. when water went over the berm tanks
floated away.
And the Big reason was the pumps did not have CFM capacity that was
needed and
Pump generators were flooded.
All you Apple fans Hang your head.
Steve Jobs Passed Away today he was 56.
___
http://www.okiebenz.com
For new and used parts go to www.okiebenz.com
To search list archives http://www.okiebenz.com/archive/
To Unsubscribe or change delivery options go to:
It's Toast Wilton.
I'll take it off your hands for Kaleb Price Plus 50 bucks. Grins
Russ W.
On 10/3/2011 11:39 AM, WILTON wrote:
Well, y'all haven't offered any magic answers yet, so I'll grab a
flashlight and go out and see if can see something a little
better.;))
Wilton
-
Goo Gone should get the shipping tag off. Let it soak for 30min or more.
Detergent won't touch the glue on it.
I'd use Hi Temp paint. Reg Rustoleum will burn off real quick.
Russ W.
On 9/20/2011 8:51 PM, Allan Streib wrote:
I pulled the exhaust off my W116 tonight. Everything unbolted easily
Me too!
Eat a Burger and Drown it with a Beer for me.
Russ W.
On 9/10/2011 11:30 AM, WILTON wrote:
'Wish I were there! Enjoy!
Wilton
- Original Message - From: Max Dillon
meadedil...@bellsouth.net
To: Mercedes Discussion List mercedes@okiebenz.com
Sent: Saturday, September 10,
Go to Rusty's an search for _W0133-1617422_
http://www.buymbparts.biz/item.wws?sku=W0133-1617422itempk=10691mfr=OESweight=0.50
that should be the part.
Russ W.
On 9/6/2011 3:12 PM, Dieselhead wrote:
That is part of it. I also need the mating part that connects the
throttle ball joint to the
Use OEM Plugs. You can presoak the plugs with ATF/Acetone.
IMPORTANT make sure the engine is STONE DEAD COLD before extracting
the old plugs.
Russ W.
Who looked at neighbors Burb that had Plug threads pulled out when he
tried to change
them when eng. had been sitting 30 min before he tried to
Daughter and SIL have Bosch they love them. Daughter's is 5 years old
and had no problems.
SIL is about 15 yo and only repair was door gasket thanks to one of her
nieces.
Both units are very quite more than a few feet away and you can't tell
they are running.
Russ W.
On 8/31/2011 8:57 PM,
Doc Booth said to use a .38 Special shell casing to hold it open..
Or you can get Rusty to order you the Official one from Mom Benz.
Russ W.
On 8/30/2011 8:01 PM, Craig wrote:
On Tue, 30 Aug 2011 20:39:02 -0400 Allan Streibstr...@cs.indiana.edu
wrote:
Alex Chamberlainapchamberl...@gmail.com
WhoooH that's good news.
On 8/27/2011 8:51 AM, WILTON wrote:
Light to moderate rain and wind all night here in Goldsboro, NC, on west side
of Irene. Occasional gust to 35 mph to 40 mph; had a gust to 'bout 50 an hour
and a half or so ago. Light rain and wind now. Lotsa small
If you can find a Marathon station their diesel fuel that they sell here
meets European specs.
This is according to a friend that is a chemist for Marathon here in La.
He does all the testing for diesel products. Cetane rating is 50 or above.
Marathon exports about 40% of their diesel output to
To all East Coast Lister's.
With Hurricane Irene bearing down on the East Coast.
Here is some advice from someone that's BTDT (too many times to count).
If You live in a area that is prone to Flooding. GET THE H?LL out of Dodge.
If You stay Make sure you have a 3 day supply of Canned Food and a
Mitch I can forward that email directly to you if you want me to.
Russ
On 8/20/2011 7:56 AM, Mitch Haley wrote:
Dan Penoff wrote:
Use this at Autozone this weekend.
If you're having trouble viewing images, view online version.
A working link to that online version of the coupon would be
Andrew, Check out http://kahlon.com/ they have good prices on High
Performance batteries to.
Bought one three years ago for my Compaq Lappy still holding a full charge.
Russ W.
On 8/18/2011 10:37 AM, Dan Penoff wrote:
Looks like two choices for your MBP - a 58WH ($95) and a 60WH - ($114).
That's because they are owned by Newegg.
On 8/15/2011 2:41 PM, Dan Penoff wrote:
If you have a CompUSA nearby they have everything you need at a little bit more
than NewEgg. In fact, they have some sort of partnership with NewEgg.
Dan
Sent from my iPhone
On Aug 15, 2011, at 3:31 PM, Kaleb
I use Directron (Houston Based) or Newegg foe 90% of my needs.
Newegg has specials on BareBones systems that are hard to beat.
Had Bad experiences with Tiger Direct on their shipping cost i.e 15
bucks for USPS shipping on a part that
weighed 7oz. Sh
Russ W.
On 8/15/2011 2:31
Kaleb
MSI makes some good Mobos. The AMD Phenom CPU is a good one also.
The only thing I don't like about the system is the 400w PS. 500w is the
least that
I use when building a system for a client.
That's my 2¢ worth.
Russ W.
On 8/15/2011 5:47 PM, Kaleb C. Striplin wrote:
what about
On 8/1/2011 9:25 AM, Dan Penoff wrote:
Using body clay is an annual procedure for proper finish care.
It doesn't entail any sort of special effort, for that matter, it is a very
simple process that is nearly impossible to screw up or do incorrectly.
A couple of pointers:
1.) Clay brand
Hi Donald,
I would use Premium fuel only and Mid Grade in a pinch.
Sure the computer will compensate for the lower octane but fuel mileage
and performance WILL suffer.
If you want to ask an expert go here:
http://www.agcoauto.com/content/submit-question
Ask Louis the question he will give you
Alan,
The Pins that hold the pads in on ATE's have little spring clips on the end.
Bendix Pins have cotter pins that hold them in.
Russ W
On 7/18/2011 9:18 AM, aland...@knology.net wrote:
Need to rebuild the brake calipers on my '83 300D. Don't know if they are ATE
or Bendix as I don't find
Bendix Photo
http://www.buymbparts.biz/ShopByVehicle.epc?q=yearid=1984@@1984makeid=63@@MERCEDES@@Xmodelid=6192%3AED|1135%3AMBC
ATE Photo
And parts for Asian cars.
Thanks Rusty for the Pos. Battery Cable for Daughters Honda.
Arrived Sat. Now just to find the time when it's NOT 100+° .
Stealerships wanted over 100 bucks for it. Rusty had it for less than 50.
Russ W.
On 7/11/2011 10:32 AM, Rusty Cullens wrote:
Don't forget that I
PO had put an aftermarket Positive Battery Cable clamp on it. Which
broke when
I tried to remove it to clean up corrosion on the clamp.
Rigged up a new one to work until the cable I ordered from Rusty came in.
Russ W.
On 7/11/2011 1:28 PM, andrew strasfogel wrote:
Thanks for the POS battery
That's Good News.
Welcome Home
On 7/4/2011 3:24 PM, Craig wrote:
After a week at the Glorieta Baptist Conference Center in Glorieta, NM,
we are back home and have the computer set up and running. Nothing here
was damaged.
Craig
___
http://www.okiebenz.com
At 1930 CDT here in South Louisiana it's a Chilly 93 with a Heat Index
of 101 :-D
Russ W.
On 6/30/2011 7:03 PM, G Mann wrote:
We measured 148 F on the ramp at D'ahran airport in Saudi in the late
60's which is in keeping with the known fact that Saudi truly is hell
anyway.
Moved to
I installed one of those last week on a client's Mom's Win XP system.
Works Great. And if I recall correctly there were Linux drivers on the
Install CD.
Russ W.
On 6/28/2011 6:21 PM, Mitch Haley wrote:
diese...@pisquared.net wrote:
Can anyone suggest a way to add wireless capability to our
Congrats
On 6/24/2011 1:47 PM, Jaime Kopchinski wrote:
I'm happy to share some good news! Janet and I had a son this week! Sidney
Jacob Kopchinski was born on Wednesday afternoon, 6lbs, 10 oz.
One picture lives here for now http://www.sidkop.com/
Mother and son are feeling good and doing
Congratulations on both additions
On 6/21/2011 9:56 AM, Donald Snook wrote:
Hello Mercedes List!
I have been out of pocket for a while and am finally catching up. Some of you
probably know about our Adoption saga. We tried to adopt a baby back in
December/January. That fell through.
Join the crowd Andrew.
Russ W. (No Twitter, FaceBook Or MySpace)
On 6/16/2011 10:07 AM, andrew strasfogel wrote:
I may be the last person in North America without a twitter account
On Thu, Jun 16, 2011 at 9:02 AM, Rich Thomas
richthomas79td...@constructivity.net wrote:
What's your
Dan,
Is this what you are looking for.
http://www.alphashark.com/p-1945-j-fold-wingtip-genuine-top-grain-leather-wallet.aspx?pmc=sbaffiliateid=10056utm_campaign=sharkbite1utm_source=email
Russ
On 6/12/2011 3:47 PM, LWB250 wrote:
As there are a number of esoteric and free thinking folks on
Around here it's NAPA, Car Quest/ Advance then Autozone.
Most Autozoners around here are so dumb they'll tell you Your Mb diesel uses
spark plugs NOT Glow Plugs. Sheee
Russ W
On 6/7/2011 7:01 PM, Curt Raymond wrote:
Ugh, around here if you're too dumb to work at Car Quest you go work
Yep it had an autopilot.
At 75, ft the there was only IIRC 10Kts difference between Vne and
Stall speeds.
On 6/6/2011 3:38 PM, Mountain Man wrote:
Russ W. wrote:
Another amazing work of Kelly Johnson and the Skunk Works.
Cool.
Now, what about controlling that beast in flight?
The SR-71 leaked like a sieve on the ground. From the SR-71's Wikipedia
site.
Fuel
Development began with using a coal slurry powerplant,^[20]
http://en.wikipedia.org/wiki/Lockheed_SR-71_Blackbird#cite_note-johnson_bio-21
but Johnson determined that the coal particles damaged engine
Bill,
Try pulling the CMOS Battery and replace it with a fresh one.
I had a client that has a Dell Optiplex that was doing the same thing
last week.
Pulled the battery and tested it. Voltage was Ok. Reinstalled it and
same thing
No Keyboard present. For Grins and Giggles I installed a brand
Because they can.
If people won't buy them then they'll stop selling crap.
Russ W.
On 5/21/2011 3:40 PM, Kaleb C. Striplin wrote:
yea no joke but how the heck can they sell mp3s online with scratches
in them?
On 5/21/2011 3:38 PM, Rich Thomas wrote:
If you have an old turntable, you can use
Andrew,
I called a local nursery and talked to the owner, who has a radio show
here on Sat morn.
He agrees with Rich.
Small 2-4 inch tender shoot dip in Rooting Powder plant in Sterile
Potting Soil. Keep Moist NOT Soaking wet.
Should see roots in 3 to 4 weeks. Keep soil above 72° .
Russ
On
Craig that's a headlight switch
The Ignition switch is under the Steering Category.
But for some reason tonight it's showing No In Stock
Last night it was. H'm
On 5/4/2011 11:15 PM, Craig wrote:
On Tue, 03 May 2011 23:31:02 -0500 Russ Williamsrawil...@eatel.net
wrote:
Switch is on Rusty's
Switch is on Rusty's site
http://www.buymbparts.biz/ShopByVehicle.epc?q=yearid=1983%40%401983makeid=63%40%40MERCEDES%40%40Xmodelid=6191%3AED|1135%3AMBC|1504%40%40300Dkeyword=switchsubcatid=P:241656@@Ignition%20Switchmode=PA
and only 29.88
If the link doesn't come thru select you year and
Segate and Maxtor has the free edition of Acronis on their web sites,
but for each you have to
have one drive of that make on the computer you are using it on.
Clonezilla works fine.
Marcium Reflect is a good free program also.
Russ W.
On 4/29/2011 8:44 AM, Gerry Archer wrote:
Thanks, Douglas.
Jim,
There are 3 bolts that have to be loosened.
2 on the alt one top one bottom and one where the bracket mounts to the
block.
If you don't loosen them the adjusting bolt will bend DAMHIK. when you
get the Alt
adjusted tighten them back up. They are either 15 or 17 mm.
Russ W.
On 4/19/2011
The top ears should have a spacer between the ears with a bolt that runs
from the back to the front
thru the slot on the bracket with a large washer and a lock nut.
I'll try to tack a couple of pics tomorrow of the setup on my 240D it's
the same as a 617.
Come to think of it have to asjust the
List CostWholesale Cost Dealer Cost
According to the Access file from the link that Mao posted a few weeks back.
Russ W.
On 4/14/2011 9:10 AM, Alex Chamberlain wrote:
On Wed, Apr 13, 2011 at 5:23 PM, Mountain Manmaontin@gmail.com wrote:
I read 4675 pages of text - no headings. I
and I voted for her from 51% to 52%...
Russ W.
On 4/2/2011 3:47 PM, Curt Raymond wrote:
I voted her from 49% - 51%...
-Curt
From: Tim Cbb...@crone.us
To: Mercedes Discussion Listmercedes@okiebenz.com
Subject: Re: [MBZ] Way, way OT: SWMBO's Healthy Choices project...
Radio Shuck has it and most electrical supply houses.
On 3/27/2011 12:17 PM, Curt Raymond wrote:
Where does one obtain De-Oxit?
My '84 190D has a flaky stalk, it'll sometimes turn out the lights completely
if its in the wrong position. I presume its dirty contacts as its been getting
better
That's a Rainbow Allan
We've had one for 20+ years. With one motor change.
You empty the water after each use. And store with no water in the tank.
One on the neat features is you can set it in a room with the tank
filled and turn it
on for an hour or so it will pull the dust out out of the air.
Loren
Go to this web address : http://www.agcoauto.com/content/submit-question
Send Lewis the question you posted here. He will answer you within 24 hours.
This guy is a straight shooter. Won't give you a bunch of malarkey.
Or you can tunin to his radio show on the net tomorrow at 10:00 CDT @
8mm for the hold down nut and 12mm for the plug.
Gear wrenches for both or a 8mm swivel 1/4 socket for the nut.
Russ W.
Who just replaced the GP's on the 300D.
_
From: mercedes-boun...@okiebenz.com [mailto:mercedes-boun...@okiebenz.com]
On Behalf Of Rich Thomas
Sent: Thursday, March
Loren you can use PowerPoint or Open Office to extract the Audio from a PPS
file
Go here :
http://presentationsoft.about.com/od/powerpointtipsandfaqs/ss/07soundht
ml.htm
http://presentationsoft.about.com/od/powerpointtipsandfaqs/ss/07soundhtm
l.htm
for instructions on how to do it on PP.
201 - 300 of 522 matches
Mail list logo